Preliminary Design and Hydrodynamic Analysis on the Offshore Integrated Anemometer Mast During Wet-Towing

2018 ◽  
Author(s):  
Zhang Puyang ◽  
Hu Ruiqi ◽  
Ding Hongyan ◽  
Le Conghuan
Keyword(s):  
Dynamic Response ◽  
Three Dimensional ◽  
Structure Design ◽  
The Self ◽  
Preliminary Design ◽  
Critical Factors ◽  
Sea State ◽  
Hydrodynamic Analysis ◽  
Expensive Equipment ◽  
Sea Bed

An offshore integrated anemometer mast (OIAM) is proposed to integrate the offshore installation of the foundation and steel mast into one operation. It can be prefabricated onshore and transported to the installation site which is simple in construction, rapid in speed and saving in cost. The most critical technique of the OIAM is the self-floating towing technique with a reasonable subdivision inside the floating tank. These subdivisions of OIAM facilitate the floating stability in case the occurrence of a damaged compartment. The tank will be ballasted to lower OIAM down and to penetrate these shallow skirt plates underneath into the sea bed after a free-floating towing process. To study and predict the dynamic behaviors of the OIAM in different sea conditions considering different towing critical factors, the hydrodynamic software MOSES is used to simulate the three-dimensional motion of the OIAM in the towing operation. Before that the integrated installation technique is introduced in terms of structure design, towing operation, and sinking on-site. The numerical results show that multiple subdivisions guarantee an adequate floating stability, and the hydrodynamic features indicate that a relative small dynamic response in some extreme sea state can be obtained by this OIAM structure. The self-floating technique of OIAM in sea is highly competitive for saving cost by using less expensive equipment in towing transportation.

scholarly journals Dynamic Response Analysis of a Bulk Carrier by Nonlinear Hydroelastic Method

2021 ◽  
Vol 9 (8) ◽  
pp. 877
Author(s):  
Zhanyang Chen ◽  
Hongbin Gui ◽  
Xiyu Liao ◽  
Mengchao Du
Keyword(s):  
Dynamic Response ◽  
Three Dimensional ◽  
Beam Theory ◽  
High Strength ◽  
Structure Design ◽  
Response Analysis ◽  
Restoring Force ◽  
Element Analysis ◽  
Response Method ◽  
Classical Beam Theory

With increasing demands for huge ship dimensions and the wide use of high-strength steel, the influence of slamming and elastic structure on structural strength cannot be ignored. Therefore, in this paper, a three-dimensional (3D) nonlinear hydroelastic theory is introduced, in which the nonlinear hydrostatic restoring force caused by instantaneous wetted surface as well as slamming force are taken into consideration, and the bending moments with/without slamming effects are calculated, respectively. Numerical simulations of the dynamic response of a flexible hull at different speeds are carried out using the finite element analysis software MSC/PATRAN. By comparison with the results of classical beam theory, the accuracy of the dynamic analysis method is studied. Finally, the dynamic response method is compared with the quasi-static method and classical beam theory. By analyzing and quantifying the influence of forward speed and nonlinear factors on structural responses, the reasonable applicable conditions for different methods are discussed, which can be used as reference in the structure design of bulk carriers.

Origami-Based Self-Folding Structure Design and Fabrication Using Projection Based Stereolithography

2015 ◽  
Vol 137 (2) ◽  
Author(s):  
Dongping Deng ◽  
Yong Chen
Keyword(s):  
3D Structure ◽  
Three Dimensional ◽  
Experimental Tests ◽  
Middle Layer ◽  
Structure Design ◽  
The Self ◽  
Two Dimensional ◽  
Polystyrene Film ◽  
Folding Structure ◽  
Unique Capability

Self-folding structures have unique capability such as reconfiguration during their usage. Such capability can be beneficial for a wide variety of applications including biomedical and electronics products. In this paper, a novel fabrication approach based on a three-dimensional (3D) printing process is presented for fabricating self-folding structures that can be actuated in a heating environment. The thermo-actuating structures that are designed and fabricated by our method are two-dimensional (2D) origami sheets, which have multiple printed layers. The middle layer of an origami sheet is a prestrained polystyrene film with large shrinkage ratios when heated. Both its top and bottom surfaces are covered with cured resin that is printed in designed shapes. A foldable hinge is achieved by constraining the shrinkage of the film on one side while allowing the shrinkage of the film on another side when the origami sheet is exposed to a heating environment. Heuristic models of hinge's folding angles are developed based on the related folding mechanism. A 2D origami sheet design and fabrication method is presented for a given 3D structure. Various experimental tests are performed to verify the self-folding performance of the designed and fabricated origami sheets. Techniques on improving folding angle control are also discussed with possible applications.

Nanoscale Self-Assembly Using Ion and Electron Beam Techniques: A Rapid Review

MRS Advances ◽  
2020 ◽  
Vol 5 (64) ◽  
pp. 3507-3520
Author(s):  
Chunhui Dai ◽  
Kriti Agarwal ◽  
Jeong-Hyun Cho
Keyword(s):  
Electron Beam ◽  
Self Assembly ◽  
Ion Beam ◽  
Three Dimensional ◽  
The Self ◽  
Stress Generation ◽  
Rapid Review ◽  
High Yield ◽  
3D Nanostructures ◽  
Self Assembled

AbstractNanoscale self-assembly, as a technique to transform two-dimensional (2D) planar patterns into three-dimensional (3D) nanoscale architectures, has achieved tremendous success in the past decade. However, an assembly process at nanoscale is easily affected by small unavoidable variations in sample conditions and reaction environment, resulting in a low yield. Recently, in-situ monitored self-assembly based on ion and electron irradiation has stood out as a promising candidate to overcome this limitation. The usage of ion and electron beam allows stress generation and real-time observation simultaneously, which significantly enhances the controllability of self-assembly. This enables the realization of various complex 3D nanostructures with a high yield. The additional dimension of the self-assembled 3D nanostructures opens the possibility to explore novel properties that cannot be demonstrated in 2D planar patterns. Here, we present a rapid review on the recent achievements and challenges in nanoscale self-assembly using electron and ion beam techniques, followed by a discussion of the novel optical properties achieved in the self-assembled 3D nanostructures.

Simulating Self-Regeneration and Self-Replication Processes Using Movable Cellular Automata with a Mutual Equilibrium Neighborhood

2020 ◽  
Vol 29 (4) ◽  
pp. 741-757
Author(s):  
Kateryna Hazdiuk ◽  
◽  
Volodymyr Zhikharevich ◽  
Serhiy Ostapov ◽  
◽  
...  
Keyword(s):  
Cellular Automata ◽  
Cellular Automaton ◽  
Three Dimensional ◽  
Computer Models ◽  
The Self ◽  
Model Construction ◽  
Natural Phenomena ◽  
Different Types ◽  
Movable Cellular Automata ◽  
Self Replication

This paper deals with the issue of model construction of the self-regeneration and self-replication processes using movable cellular automata (MCAs). The rules of cellular automaton (CA) interactions are found according to the concept of equilibrium neighborhood. The method is implemented by establishing these rules between different types of cellular automata (CAs). Several models for two- and three-dimensional cases are described, which depict both stable and unstable structures. As a result, computer models imitating such natural phenomena as self-replication and self-regeneration are obtained and graphically presented.

scholarly journals Detecting the Mechanism behind the Transition from Fixed Two-Dimensional Patterned Sika Deer (Cervus nippon) Dermal Papilla Cells to Three-Dimensional Pattern

2021 ◽  
Vol 22 (9) ◽  
pp. 4715
Author(s):  
Guanning Wei ◽  
Hongmei Sun ◽  
Haijun Wei ◽  
Tao Qin ◽  
Yifeng Yang ◽  
...  
Keyword(s):  
Culture Condition ◽  
Sika Deer ◽  
Three Dimensional ◽  
Cervus Nippon ◽  
Dermal Papilla ◽  
Growth Patterns ◽  
The Self ◽  
Dermal Papilla Cells ◽  
Aggregative Behavior ◽  
Cell Pattern

The hair follicle dermal papilla is critical for hair generation and de novo regeneration. When cultured in vitro, dermal papilla cells from different species demonstrate two distinguishable growth patterns under the conventional culture condition: a self-aggregative three dimensional spheroidal (3D) cell pattern and a two dimensional (2D) monolayer cell pattern, correlating with different hair inducing properties. Whether the loss of self-aggregative behavior relates to species-specific differences or the improper culture condition remains unclear. Can the fixed 2D patterned dermal papilla cells recover the self-aggregative behavior and 3D pattern also remains undetected. Here, we successfully constructed the two growth patterns using sika deer (Cervus nippon) dermal papilla cells and proved it was the culture condition that determined the dermal papilla growth pattern. The two growth patterns could transit mutually as the culture condition was exchanged. The fixed 2D patterned sika deer dermal papilla cells could recover the self-aggregative behavior and transit back to 3D pattern, accompanied by the restoration of hair inducing capability when the culture condition was changed. In addition, the global gene expressions during the transition from 2D pattern to 3D pattern were compared to detect the potential regulating genes and pathways involved in the recovery of 3D pattern and hair inducing capability.

scholarly journals Investigation of Pressure Oscillation and Cavitation Characteristics for Submerged Self-Resonating Waterjet

2021 ◽  
Vol 11 (15) ◽  
pp. 6972
Author(s):  
Lihua Cui ◽  
Fei Ma ◽  
Tengfei Cai
Keyword(s):  
Sudden Change ◽  
Three Dimensional ◽  
Pressure Oscillation ◽  
Experimental Tests ◽  
Low Pressure ◽  
The Self ◽  
Two Phase ◽  
Cavitation Phenomenon ◽  
Pressure Zone ◽  
Unsteady Characteristics

The cavitation phenomenon of the self-resonating waterjet for the modulation of erosion characteristics is investigated in this paper. A three-dimensional computational fluid dynamics (CFD) model was developed to analyze the unsteady characteristics of the self-resonating jet. The numerical model employs the mixture two-phase model, coupling the realizable turbulence model and Schnerr–Sauer cavitation model. Collected data from experimental tests were used to validate the model. Results of numerical simulations and experimental data frequency bands obtained by the Fast Fourier transform (FFT) method were in very good agreement. For better understanding the physical phenomena, the velocity, the pressure distributions, and the cavitation characteristics were investigated. The obtained results show that the sudden change of the flow velocity at the outlet of the nozzle leads to the forms of the low-pressure zone. When the pressure at the low-pressure zone is lower than the vapor pressure, the cavitation occurs. The flow field structure of the waterjet can be directly perceived through simulation, which can provide theoretical support for realizing the modulation of the erosion characteristics, optimizing nozzle structure.

scholarly journals Porous Characteristics of Three-Dimensional Disordered Graphene Networks

Crystals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 127
Author(s):  
YongChao Wang ◽  
YinBo Zhu ◽  
HengAn Wu
Keyword(s):  
Pore Size ◽  
Low Temperatures ◽  
Gas Adsorption ◽  
Three Dimensional ◽  
Md Simulations ◽  
Structural Features ◽  
Atomic Scale ◽  
Critical Factors ◽  
Chlorination Process ◽  
Porous Morphology

The porous characteristics of disordered carbons are critical factors to their performance on hydrogen storage and electrochemical capacitors. Even though the porous information can be estimated indirectly by gas adsorption experiments, it is still hard to directly characterize the porous morphology considering the complex 3D connectivity. To this end, we construct full-atom disordered graphene networks (DGNs) by mimicking the chlorination process of carbide-derived carbons using annealing-MD simulations, which could model the structure of disordered carbons at the atomic scale. The porous characteristics, including pore volume, pore size distribution (PSD), and specific surface area (SSA), were then computed from the coordinates of carbon atoms. From the evolution of structural features, pores grow dramatically during the formation of polyaromatic fragments and sequent disordered framework. Then structure is further graphitized while the PSD shows little change. For the obtained DGNs, the porosity, pore size, and SSA increase with decreasing density. Furthermore, SSA tends to saturate in the low-density range. The DGNs annealed at low temperatures exhibit larger SSA than high-temperature DGNs because of the abundant free edges.

scholarly journals Dynamic response analysis for multi-degrees-of-freedom parallel mechanisms with various types of three-dimensional clearance joints

2021 ◽  
Vol 18 (3) ◽  
pp. 172988142110177
Author(s):  
Jia Yonghao ◽  
Chen Xiulong
Keyword(s):  
Dynamic Response ◽  
Multibody Systems ◽  
Parallel Mechanism ◽  
Three Dimensional ◽  
Response Analysis ◽  
Parallel Mechanisms ◽  
Dynamics Model ◽  
Clearance Joints ◽  
Clearance Joint ◽  
Spatial Parallel Mechanism

For spatial multibody systems, the dynamic equations of multibody systems with compound clearance joints have a high level of nonlinearity. The coupling between different types of clearance joints may lead to abundant dynamic behavior. At present, the dynamic response analysis of the spatial parallel mechanism considering the three-dimensional (3D) compound clearance joint has not been reported. This work proposes a modeling method to investigate the influence of the 3D compound clearance joint on the dynamics characteristics of the spatial parallel mechanism. For this purpose, 3D kinematic models of spherical clearance joint and revolute joint with radial and axial clearances are derived. Contact force is described as normal contact and tangential friction and later introduced into the nonlinear dynamics model, which is established by the Lagrange multiplier technique and Jacobian of constraint matrix. The influences of compound clearance joint and initial misalignment of bearing axes on the system are analyzed. Furthermore, validation of dynamics model is evaluated by ADAMS and Newton–Euler method. This work provides an essential theoretical basis for studying the influences of 3D clearance joints on dynamic responses and nonlinear behavior of parallel mechanisms.

3-D elastic coupling vibration and acoustical radiation characteristics of cracked gear under elastic support condition

2015 ◽  
Vol 23 (9) ◽  
pp. 1548-1568 ◽  
Author(s):  
Shao Renping ◽  
Purong Jia ◽  
Xiankun Qi
Keyword(s):  
Dynamic Response ◽  
Support System ◽  
Three Dimensional ◽  
Elastic Support ◽  
Dynamic Responses ◽  
Tooth Root ◽  
Support Condition ◽  
Elastic Boundary ◽  
Root Crack ◽  
Elastic Disc

According to the actual working condition of the gear, the supporting gear shaft is treated as an elastic support. Its impact on the gear body vibration is considered and investigated and the dynamic response of elastic teeth and gear body is analyzed. On this basis, the gear body is considered as a three-dimensional elastic disc and the gear teeth are treated as an elastic cantilever beam. Under the conditions of the elastic boundary (support shaft), combining to the elastic disk and elastic teeth, the influence of three-dimensional elastic discs on the meshing tooth response under an elastic boundary condition is also included. A dynamic model of the gear support system and calculated model of the gear tooth response are then established. The inherent characteristics of the gear support system and dynamics response of the meshing tooth are presented and simulated. It was shown by the results that it is correct to use the elastic support condition to analyze the gear support system. Based on the above three-dimensional elastic dynamics analysis, this paper set up a dynamics coupling model of a cracked gear structure support system that considered the influence of a three-dimensional elastic disc on a cracked meshing tooth under elastic conditions. It discusses the dynamic characteristic of the cracked gear structure system and coupling dynamic response of the meshing tooth, offering a three-dimensional elastic body model of the tooth root crack and pitch circle crack with different sizes, conducting the three-dimensional elastic dynamic analysis to the faulty crack. ANSYS was employed to carry out dynamic responses, as well as to simulate the acoustic field radiation orientation of a three-dimensional elastic crack body at the tooth root crack and pitch circle with different sizes.

Dynamic Response of Frame Structure with Different Stiffness in Two Horizontal Directions under Oblique Seismic Action

2013 ◽  
Vol 368-370 ◽  
pp. 1644-1647
Author(s):  
Zhen Bao Li ◽  
Hai Teng Wang ◽  
Li Fei Liu ◽  
Wen Jing Wang
Keyword(s):  
Dynamic Response ◽  
Ground Motion ◽  
Structure Design ◽  
Frame Structure ◽  
Maximum Response ◽  
Seismic Action

The ground motion is multidimensional, random and uncertain in directions when earthquakes occur, so dynamic response under oblique seismic action needs to be considered in the structure design. A frame structure with different stiffness in two horizontal directions was analyzed under seismic action with different input angles. The maximum response of beams and columns was obtained. The seismic mechanism of structures under oblique seismic action was discussed.

Sign in / Sign up

Export Citation Format

Share Document