Two- and Three-Dimensional Simulations of the Flow Around a Cylinder Fitted With Strakes

2012 ◽  
Author(s):  
Bruno S. Carmo ◽  
Rafael S. Gioria ◽  
Ivan Korkischko ◽  
Cesar M. Freire ◽  
Julio R. Meneghini
Keyword(s):  
Reynolds Number ◽  
Vortex Shedding ◽  
Free Stream ◽  
Three Dimensional ◽  
The Body ◽  
Vortex Wake ◽  
Two Dimensional ◽  
Flow Around A Cylinder ◽  
Three Dimensional Simulations ◽  
Angle Of Rotation

Two- and three-dimensional simulations of the flow around straked cylinders are presented. For the two-dimensional simulations we used the Spectral/hp Element Method, and carried out simulations for five different angles of rotation of the cylinder with respect to the free stream. Fixed and elastically-mounted cylinders were tested, and the Reynolds number was kept constant and equal to 150. The results were compared to those obtained from the simulation of the flow around a bare cylinder under the same conditions. We observed that the two-dimensional strakes are not effective in suppressing the vibration of the cylinders, but also noticed that the responses were completely different even with a slight change in the angle of rotation of the body. The three-dimensional results showed that there are two mechanisms of suppression: the main one is the decrease in the vortex shedding correlation along the span, whilst a secondary one is the vortex wake formation farther downstream.

Bifurcation Characteristics of Flows in Rectangular Sudden Expansion Channels

2005 ◽  
Author(s):  
Francine Battaglia ◽  
George Papadopoulos
Keyword(s):  
Reynolds Number ◽  
Laminar Flow ◽  
Critical Reynolds Number ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Expansion Ratio ◽  
Sudden Expansion ◽  
Two Dimensional ◽  
Effective Expansion ◽  
Three Dimensional Simulations

The effect of three-dimensionality on low Reynolds number flows past a symmetric sudden expansion in a channel was investigated. The geometric expansion ratio of in the current study was 2:1 and the aspect ratio was 6:1. Both experimental velocity measurements and two- and three-dimensional simulations for the flow along the centerplane of the rectangular duct are presented for Reynolds numbers in the range of 150 to 600. Comparison of the two-dimensional simulations with the experiments revealed that the simulations fail to capture completely the total expansion effect on the flow, which couples both geometric and hydrodynamic effects. To properly do so requires the definition of an effective expansion ratio, which is the ratio of the downstream and upstream hydraulic diameters and is therefore a function of both the expansion and aspect ratios. When the two-dimensional geometry was consistent with the effective expansion ratio, the new results agreed well with the three-dimensional simulations and the experiments. Furthermore, in the range of Reynolds numbers investigated, the laminar flow through the expansion underwent a symmetry-breaking bifurcation. The critical Reynolds number evaluated from the experiments and the simulations was compared to other values reported in the literature. Overall, side-wall proximity was found to enhance flow stability, helping to sustain laminar flow symmetry to higher Reynolds numbers in comparison to nominally two-dimensional double-expansion geometries. Lastly, and most importantly, when the logarithm of the critical Reynolds number from all these studies was plotted against the reciprocal of the effective expansion ratio, a linear trend emerged that uniquely captured the bifurcation dynamics of all symmetric double-sided planar expansions.

Flow past a rotationally oscillating cylinder

2013 ◽  
Vol 735 ◽  
pp. 307-346 ◽  
Author(s):  
S. Kumar ◽  
C. Lopez ◽  
O. Probst ◽  
G. Francisco ◽  
D. Askari ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Vortex Shedding ◽  
Three Dimensional ◽  
Far Field ◽  
Two Dimensional ◽  
Flow Past ◽  
Vortex Shedding Frequency ◽  
Shedding Frequency ◽  
Flow Visualizations ◽  
Hydrogen Bubble Technique

AbstractFlow past a circular cylinder executing sinusoidal rotary oscillations about its own axis is studied experimentally. The experiments are carried out at a Reynolds number of 185, oscillation amplitudes varying from $\mathrm{\pi} / 8$ to $\mathrm{\pi} $, and at non-dimensional forcing frequencies (ratio of the cylinder oscillation frequency to the vortex-shedding frequency from a stationary cylinder) varying from 0 to 5. The diagnostic is performed by extensive flow visualization using the hydrogen bubble technique, hot-wire anemometry and particle-image velocimetry. The wake structures are related to the velocity spectra at various forcing parameters and downstream distances. It is found that the phenomenon of lock-on occurs in a forcing frequency range which depends not only on the amplitude of oscillation but also the downstream location from the cylinder. The experimentally measured lock-on diagram in the forcing amplitude and frequency plane at various downstream locations ranging from 2 to 23 diameters is presented. The far-field wake decouples, after the lock-on at higher forcing frequencies and behaves more like a regular Bénard–von Kármán vortex street from a stationary cylinder with vortex-shedding frequency mostly lower than that from a stationary cylinder. The dependence of circulation values of the shed vortices on the forcing frequency reveals a decay character independent of forcing amplitude beyond forcing frequency of ${\sim }1. 0$ and a scaling behaviour with forcing amplitude at forcing frequencies ${\leq }1. 0$. The flow visualizations reveal that the far-field wake becomes two-dimensional (planar) near the forcing frequencies where the circulation of the shed vortices becomes maximum and strong three-dimensional flow is generated as mode shape changes in certain forcing parameter conditions. It is also found from flow visualizations that even at higher Reynolds number of 400, forcing the cylinder at forcing amplitudes of $\mathrm{\pi} / 4$ and $\mathrm{\pi} / 2$ can make the flow field two-dimensional at forcing frequencies greater than ${\sim }2. 5$.

scholarly journals The onset of unsteadiness of two-dimensional bodies falling or rising freely in a viscous fluid: a linear study

2011 ◽  
Vol 690 ◽  
pp. 173-202 ◽  
Author(s):  
Pauline Assemat ◽  
David Fabre ◽  
Jacques Magnaudet
Keyword(s):  
Reynolds Number ◽  
Viscous Fluid ◽  
Strouhal Number ◽  
Cross Section ◽  
Vortex Shedding ◽  
The Body ◽  
Mode Switching ◽  
Two Dimensional ◽  
Body Dynamics ◽  
Mass Ratios

AbstractWe consider the transition between the steady vertical path and the oscillatory path of two-dimensional bodies moving under the effect of buoyancy in a viscous fluid. Linearization of the Navier–Stokes equations governing the flow past the body and of Newton’s equations governing the body dynamics leads to an eigenvalue problem, which is solved numerically. Three different body geometries are then examined in detail, namely a quasi-infinitely thin plate, a plate of rectangular cross-section with an aspect ratio of 8, and a rod with a square cross-section. Two kinds of eigenmodes are observed in the limit of large body-to-fluid mass ratios, namely ‘fluid’ modes identical to those found in the wake of a fixed body, which are responsible for the onset of vortex shedding, and four additional ‘aerodynamic’ modes associated with much longer time scales, which are also predicted using a quasi-static model introduced in a companion paper. The stability thresholds are computed and the nature of the corresponding eigenmodes is investigated throughout the whole possible range of mass ratios. For thin bodies such as a flat plate, the Reynolds number characterizing the threshold of the first instability and the associated Strouhal number are observed to be comparable with those of the corresponding fixed body. Other modes are found to become unstable at larger Reynolds numbers, and complicated branch crossings leading to mode switching are observed. On the other hand, for bluff bodies such as a square rod, two unstable modes are detected in the range of Reynolds number corresponding to wake destabilization. For large enough mass ratios, the leading mode is similar to the vortex shedding mode past a fixed body, while for smaller mass ratios it is of a different nature, with a Strouhal number about half that of the vortex shedding mode and a stronger coupling with the body dynamics.

Wake dynamics of external flow past a curved circular cylinder with the free stream aligned with the plane of curvature

2007 ◽  
Vol 592 ◽  
pp. 89-115 ◽  
Author(s):  
A. MILIOU ◽  
A. DE VECCHI ◽  
S. J. SHERWIN ◽  
J. M. R. GRAHAM
Keyword(s):  
Circular Cylinder ◽  
Vortex Shedding ◽  
Free Stream ◽  
Three Dimensional ◽  
Axial Flow ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
The Body ◽  
Vertical Extension ◽  
Flow Past

Three-dimensional spectral/hp computations have been performed to study the fundamental mechanisms of vortex shedding in the wake of curved circular cylinders at Reynolds numbers of 100 and 500. The basic shape of the body is a circular cylinder whose centreline sweeps through a quarter section of a ring and the inflow direction lies on the plane of curvature of the quarter ring: the free stream is then parallel to the geometry considered and the part of the ring that is exposed to it will be referred to as the ‘leading edge’. Different configurations were investigated with respect to the leading-edge orientation. In the case of a convex-shaped geometry, the stagnation face is the outer surface of the ring: this case exhibited fully three-dimensional wake dynamics, with the vortex shedding in the upper part of the body driving the lower end at one dominant shedding frequency for the whole cylinder span. The vortex-shedding mechanism was therefore not governed by the variation of local normal Reynolds numbers dictated by the curved shape of the leading edge. A second set of simulations were conducted with the free stream directed towards the inside of the ring, in the so-called concave-shaped geometry. No vortex shedding was detected in this configuration: it is suggested that the strong axial flow due to the body's curvature and the subsequent production of streamwise vorticity plays a key role in suppressing the wake dynamics expected in the case of flow past a straight cylinder. The stabilizing mechanism stemming from the concave curved geometry was still found to govern the wake behaviour even when a vertical extension was added to the top of the concave ring, thereby displacing the numerical symmetry boundary condition at this point away from the top of the deformed cylinder. In this case, however, the axial flow from the deformed cylinder was drawn into the wake of vertical extension, weakening the shedding process expected from a straight cylinder at these Reynolds numbers. These considerations highlight the importance of investigating flow past curved cylinders using a full three-dimensional approach, which can properly take into account the role of axial velocity components without the limiting assumptions of a sectional analysis, as is commonly used in industrial practice. Finally, towing-tank flow visualizations were also conducted and found to be in qualitative agreement with the computational findings.

The wake behind a cylinder rolling on a wall at varying rotation rates

2010 ◽  
Vol 648 ◽  
pp. 225-256 ◽  
Author(s):  
B. E. STEWART ◽  
M. C. THOMPSON ◽  
T. LEWEKE ◽  
K. HOURIGAN
Keyword(s):  
Reynolds Number ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Wake Flow ◽  
Recirculation Region ◽  
Two Dimensional ◽  
Number Range ◽  
Rotation Rates ◽  
Transition Mechanism ◽  
Three Dimensional Simulations

A study investigating the flow around a cylinder rolling or sliding on a wall has been undertaken in two and three dimensions. The cylinder motion is specified from a set of five discrete rotation rates, ranging from prograde through to retrograde rolling. A Reynolds number range of 20–500 is considered. The effects of the nearby wall and the imposed body motion on the wake structure and dominant wake transitions have been determined. Prograde rolling is shown to destabilize the wake flow, while retrograde rotation delays the onset of unsteady flow to Reynolds numbers well above those observed for a cylinder in an unbounded flow.Two-dimensional simulations show the presence of two recirculation zones in the steady wake, the lengths of which increase approximately linearly with the Reynolds number. Values of the lift and drag coefficient are also reported for the steady flow regime. Results from a linear stability analysis show that the wake initially undergoes a regular bifurcation from a steady two-dimensional flow to a steady three-dimensional wake for all rotation rates. The critical Reynolds number Rec of transition and the spanwise wavelength of the dominant mode are shown to be highly dependent on, but smoothly varying with, the rotation rate of the cylinder. Varying the rotation from prograde to retrograde rolling acts to increase the value of Rec and decrease the preferred wavelength. The structure of the fully evolved wake mode is then established through three-dimensional simulations. In fact it is found that at Reynolds numbers only marginally (~5%) above critical, the three-dimensional simulations indicate that the saturated state becomes time dependent, although at least initially, this does not result in a significant change to the mode structure. It is only at higher Reynolds numbers that the wake undergoes a transition to vortex shedding.An analysis of the three-dimensional transition indicates that it is unlikely to be due to a centrifugal instability despite the superficial similarity to the flow over a backward-facing step, for which the transition mechanism has been speculated to be centrifugal. However, the attached elongated recirculation region and distribution of the spanwise perturbation vorticity field, and the similarity of these features with those of the flow through a partially blocked channel, suggest the possibility that the mechanism is elliptic in nature. Some analysis which supports this conjecture is undertaken.

The three-dimensional structure of the wake of a circular cylinder

1966 ◽  
Vol 25 (1) ◽  
pp. 143-164 ◽  
Author(s):  
J. H. Gerrard
Keyword(s):  
Circular Cylinder ◽  
Growth And Development ◽  
Free Stream ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
The Body ◽  
Dimensional Structure ◽  
Vortex Wake ◽  
Vortex Lines ◽  
Critical Scrutiny

A critical scrutiny of the nature of the three-dimensional characteristics of the vortex wake of a circular cylinder serves to suggest lines for further investigation and furnishes some ideas on the nature of the growth and development of these non-uniformities. It is suggested that the basic occurrence in the growth of three-dimensionality is the continuation of vortex lines, oriented more or less parallel to the body, into the direction of the free stream. The causes of this vary, as do the details of the development with the particular situation considered.Experiments were performed in a wind tunnel at Reynolds numbers based on cylinder diameter of 85, 235 and 2 × 104, at which stable, transitional and turbulent vortices were investigated.

scholarly journals Lattice gas automaton modelling of a vortex flow meter: Strouhal–Reynolds number dependence

2017 ◽  
Vol 56 (4) ◽  
pp. 191-199
Author(s):  
Vaidas Juknevičius ◽  
Jogundas Armaitis
Keyword(s):  
Reynolds Number ◽  
Strouhal Number ◽  
Vortex Shedding ◽  
Vortex Flow ◽  
Three Dimensional ◽  
Two Dimensions ◽  
Dimensional Structure ◽  
Two Dimensional ◽  
Flow Meter ◽  
Reynolds Number Dependence

Motivated by recent experimental and computational results concerning a three-dimensional structure of vortices behind a vortex shedding flow meter [M. Reik et al., Forsch. Ingenieurwes. 74, 77 (2010)], we study the Strouhal–Reynolds number dependence in the vortex street in two dimensions behind a trapezoid-shaped object by employing two types of Frisch–Hasslacher–Pomeau (FHP) models. Our geometry is intended to reproduce the operation of a vortex shedding flow meter in a two-dimensional setting, thus preventing the formation of a three-dimensional vortex structure. In particular, we check if the anomalous Reynolds–Strouhal number dependence reported for three dimensions can also be found in our two-dimensional simulation. As we find that the Strouhal number is nearly independent of the Reynolds number in this particular setup, our results provide support for the hypothesis that three-dimensional flow structures are responsible for that dependence, thus hinting at the importance of the pipe diameter to the accurate operation of industrial vortex flow meters.

Analysis of Fluid Flow in Porous Media Using the Lattice Boltzmann Method: Inertial Flow Regime

2012 ◽  
Author(s):  
Huizhe Zhao ◽  
Aydin Nabovati ◽  
Cristina H. Amon
Keyword(s):  
Reynolds Number ◽  
Lattice Boltzmann Method ◽  
Lattice Boltzmann ◽  
Critical Reynolds Number ◽  
Three Dimensional ◽  
Two Dimensional ◽  
Inertial Effects ◽  
Inertial Flow ◽  
Boltzmann Method ◽  
Three Dimensional Simulations

In this work, we use the lattice Boltzmann method to study inertial flow in three-dimensional random fibrous porous materials. In order to validate the methodology, inertial flow in two-dimensional hexagonal arrangements of circular cylinders is simulated, and the results are compared against those previously reported in the literature. The three-dimensional fibrous porous materials are then constructed by randomly placing straight cylindrical fibers inside the computational domain. Inertial effects are studied systematically for a wide range of pore Reynolds numbers in materials with porosities between 0.60 and 0.95. A previously proposed semi-empirical relation is modified to represent the inertial effects in three-dimensional fibrous materials. Three distinct regimes of constant, quadratic, and linear relations between the inverse of the permeability and pore Reynolds number are observed for both two- and three-dimensional simulations. The critical Reynolds number, beyond which the inertial effects are strong and this relation is linear, is shown to be smaller in three-dimensional simulations, when compared to the critical Reynolds number in two-dimensional simulations.

Three-Dimensional Wakes of Curved Pipes

2002 ◽  
Author(s):  
Anthi Miliou ◽  
Spencer J. Sherwin ◽  
J. Michael R. Graham
Keyword(s):  
Vortex Shedding ◽  
Stream Flow ◽  
Free Stream ◽  
Three Dimensional ◽  
Imperial College ◽  
Flow Conditions ◽  
Towing Tank ◽  
Curved Pipes ◽  
Flow Vector ◽  
Three Dimensional Simulations

A numerical investigation into the flow past curved pipes has been performed. The first group of computations includes curved pipes for which the incoming flow vector is normal to the plane of curvature. For the second group of computations the free-stream flow vector is parallel to the plane of curvature. Different flow conditions have been applied and the corresponding results compared. The vortex shedding patterns and the wake topology are studied and the sectional forces at different locations of the span are also presented. The fully three-dimensional simulations were computed with a spectral/hp element method. The computational results were compared with visualisation experiments undertaken in the towing tank facility of the Department of Aeronautics of Imperial College.

Bifurcation Characteristics of Flows in Rectangular Sudden Expansion Channels

2005 ◽  
Vol 128 (4) ◽  
pp. 671-679 ◽  
Author(s):  
Francine Battaglia ◽  
George Papadopoulos
Keyword(s):  
Reynolds Number ◽  
Laminar Flow ◽  
Critical Reynolds Number ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Expansion Ratio ◽  
Sudden Expansion ◽  
Two Dimensional ◽  
Effective Expansion ◽  
Three Dimensional Simulations

The effect of three dimensionality on low Reynolds number flows past a symmetric sudden expansion in a channel was investigated. The geometric expansion ratio in the current study was 2:1 and the aspect ratio was 6:1. Both experimental velocity measurements and two- and three-dimensional simulations for the flow along the centerplane of the rectangular duct are presented for Reynolds numbers in the range of 150 to 600. Comparison of the two-dimensional simulations with the experiments revealed that the simulations failed to capture completely the total expansion effect on the flow, which is influenced by both geometric and hydrodynamic effects. To properly do so requires the definition of an effective expansion ratio, which is the ratio of the downstream and upstream hydraulic diameters and is therefore a function of both the expansion and aspect ratios. When two-dimensional simulations were performed using the effective expansion ratio, the new results agreed well with the three-dimensional simulations and the experiments. Furthermore, in the range of Reynolds numbers investigated, the laminar flow through the expansion underwent a symmetry-breaking bifurcation. The critical Reynolds number evaluated from the experiments and the simulations were compared to other values reported in the literature. Overall, side-wall proximity was found to enhance flow stability, thus sustaining laminar flow symmetry to higher Reynolds numbers. Last, and most important, when the logarithm of the critical Reynolds number was plotted against the reciprocal of the effective expansion ratio, a linear trend emerged that uniquely captured the bifurcation dynamics of all symmetric double-sided planar expansions.

Sign in / Sign up

Export Citation Format

Share Document