Effective-Stress Finite Element Analysis of Spudcan Penetration

2012 ◽  
Author(s):  
Jiang Tao Yi ◽  
Fook Hou Lee ◽  
Siang Huat Goh ◽  
Yu Ping Li ◽  
Xi Ying Zhang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Analysis ◽  
Pore Pressure ◽  
Effective Stress ◽  
Excess Pore Pressure ◽  
Element Analysis ◽  
Pore Pressures ◽  
Excess Pore Pressures ◽  
Excess Pore

The numerical modeling of spudcan penetration involves technical challenges posed by large soil deformation coupled with significant material non-linearity. The Lagrangian approach commonly used for solid stress analysis often does not work well with large deformations, resulting in premature termination of the analysis. Recently, the Arbitrary Langrangian Eulerian (ALE) and the Eulerian methods have been used in spudcan analysis to overcome problems caused by the soil flow and large deformation. However, most of the reported studies are based on total stress analysis and therefore shed no light on the excess pore pressures generated during spudcan installation. As a result, much remains unknown about the long-term behaviour of spudcans in the ground, which is affected by the dissipation of excess pore pressures. This paper reports an effective-stress finite element analysis of spudcan installation in an over-consolidated (OC) soft clay. The Eulerian analysis was conducted using ABAQUS/ Explicit, with the effective stress constitutive models coded via the material subroutine VUMAT. The results demonstrated the feasibility of conducting effective-stress finite element analysis for undrained spudcan penetration in OC clays. The paper discusses the flow mechanism, stable cavity depths and bearing capacity factors when spudcan installation occurs in various OC soils. It was found that the pore pressure build-up concentrates in a bulb-shaped zone surrounding the spudcan. The size of the pore pressure bulb increases with increasing penetration. The maximum excess pore pressure, which is generated near the spudcan tip, is predominantly controlled by the undrained shear strength at the tip level.

Eulerian finite element analysis of excess pore pressure generated by spudcan installation into soft clay

2012 ◽  
Vol 42 ◽  
pp. 157-170 ◽  
Author(s):  
Jiang Tao Yi ◽  
Fook Hou Lee ◽  
Siang Huat Goh ◽  
Xi Ying Zhang ◽  
Jer-Fang Wu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Pore Pressure ◽  
Soft Clay ◽  
Excess Pore Pressure ◽  
Element Analysis ◽  
Excess Pore

Surpressions interstitielles développées par le fonçage dans les sols cohérents

1979 ◽  
Vol 16 (4) ◽  
pp. 814-827
Author(s):  
M. Peignaud
Keyword(s):  
Pore Pressure ◽  
Excess Pore Pressure ◽  
Overburden Pressure ◽  
Pore Pressures ◽  
Excess Pore Pressures ◽  
Plastic Clays ◽  
Excess Pore

The Laboratoire Régional des Ponts et Chaussées, Angers (France) has investigated the excess pore pressures developed during the driving of a piezometer probe at different rates on four sites. Attention is drawn to the important differences between the pore pressures measured during penetration and at rest.During driving, negative excess pore pressures are measured. When the piezometer is stopped the pore pressures become large and positive. For the soils tested, i.e., plastic to highly plastic clays, the maximum excess pore pressure at rest may be estimated from the total overburden pressure. [Journal translation]

Undrained behavior of embankments on New Liskeard varved clay

1977 ◽  
Vol 14 (3) ◽  
pp. 367-388 ◽  
Author(s):  
Suzanne M. Lacasse ◽  
Charles C. Ladd ◽  
Alex K. Barsvary
Keyword(s):  
Finite Element ◽  
Effective Stress ◽  
Field Measurements ◽  
Excess Pore Pressure ◽  
Strength Parameters ◽  
Finite Element Program ◽  
Pore Pressures ◽  
Element Program ◽  
Varved Clay ◽  
Excess Pore

The performance, including a failure, of two embankments in New Liskeard, Ontario is analysed. The underlying medium-to-soft varved clay foundation is studied with respect to stability, undrained deformations, and excess pore pressure distribution.Total stress stability analyses were performed with undrained strengths based on measured and corrected field vane strengths, the average unconfined compression and unconsolidated undrained strength, and SHANSEP strength parameters with and without anisotropy. Several approaches yielded satisfactory factors of safety and reasonable critical arcs. Effective stress analyses using pore pressures predicted from finite element analyses showed that either the effective stress strength parameters were much lower than those measured in the laboratory or the predicted pore pressures at failure were much too low.Undrained deformations and excess pore pressures at end-of-construction were predicted with the finite element program FEECON. The values were generally consistent with field measurements for an embankment located 60 m from the failure area.

A New Technique for Reduction of Excess Pore Pressures During Pile Driving

1974 ◽  
Vol 11 (3) ◽  
pp. 423-430 ◽  
Author(s):  
Robert D. Holtz ◽  
Per Boman
Keyword(s):  
Pore Pressure ◽  
Alternative Methods ◽  
New Technique ◽  
Excess Pore Pressure ◽  
Relative Reduction ◽  
Pile Driving ◽  
Pore Pressures ◽  
A New Technique ◽  
Excess Pore Pressures ◽  
Excess Pore

A new technique is described whereby excess pore pressures induced during pile driving in soft, varved silts and clays were economically reduced to a safe level. The technique was applied to piles at a bridge site south of Stockholm, Sweden, where a small slide had occurred during pile driving. A new paper–plastic drain was attached to the wood piles during driving, and two pulling tests indicated that the drain was undamaged under normal driving conditions. The excess pore pressure generated during the driving of some 13 test piles without drains and 48 piles with drains was measured. The data indicated at least a 50% relative reduction in excess pore pressure when the drain was used. In addition, the cost of the technique was considerably less than alternative methods for dealing with dangerous excess pore water pressures resulting from piling in similar soils. The technique has been successfully applied at two other piling sites in Sweden.

Numerical Analysis for Excess Pore Pressure Dissipation Process for Pressed Pile Installation

2013 ◽  
Vol 405-408 ◽  
pp. 133-137
Author(s):  
Tai Quan Zhou ◽  
Feng Tan ◽  
Cheng Li
Keyword(s):  
Finite Element ◽  
Pore Pressure ◽  
Excess Pore Pressure ◽  
Soil Behavior ◽  
Element Analysis ◽  
Dissipation Process ◽  
Pile Installation ◽  
Finite Element Software ◽  
Modified Cam Clay ◽  
Excess Pore

The finite element analysis is performed on the excess pore pressure dissipation for pressed pile installation using the ABAQUS finite element software. The modified Cam-Clay model is used to model the soil behavior. The finite slide contact model is used to model the pressed pile installation process. Based on the geology stratum of soils and drainage conditions, the excess pore pressure dissipation process is analyzed using the proposed method. The initial excess pore pressure distribution along the pile depth and the pile radius direction is obtained. The excess pore pressure dissipation after 98 days is analyzed.

Consolidation of a soil layer subsequent to cessation of deposition

2005 ◽  
Vol 42 (2) ◽  
pp. 678-682
Author(s):  
Guofu Zhu ◽  
Jian-Hua Yin
Keyword(s):  
Pore Pressure ◽  
Soil Layer ◽  
Average Degree ◽  
Excess Pore Pressure ◽  
Triangular Distribution ◽  
Pressure Distributions ◽  
Pore Pressures ◽  
Degree Of Consolidation ◽  
Excess Pore Pressures ◽  
Excess Pore

It is necessary in certain cases to estimate the progress of consolidation in a soil layer that has ceased increasing in thickness over time. In this paper, the existing excess pore pressures for two time–thickness relations are used as the "initial" pore pressures for analysing the consolidation of soil subsequent to the cessation of deposition. Average degrees of consolidation of the soil layer are presented for one-way drainage and two-way drainage boundary conditions. The average degrees of consolidation are compared with those for uniform and triangular initial excess pore pressure distributions. It is found that the average degree of consolidation for one-way drainage boundaries can be estimated using the value for the triangular distribution. The average degree of consolidation for two-way drainage boundaries is bound by the averages for both the uniform and the triangular initial excess pore pressure distributions.Key words: consolidation, deposition, drainage, settlement, soil.

scholarly journals Numerical Analysis of Staged Construction of an Embankment on Soft Soil

2021 ◽  
Author(s):  
Ayesha Binta Ali ◽  
Mehedi Ahmed Ansary
Keyword(s):  
Finite Element ◽  
Numerical Analysis ◽  
Pore Pressure ◽  
Soft Soil ◽  
Excess Pore Pressure ◽  
Element Analysis ◽  
Staged Construction ◽  
Modeling Software ◽  
Degree Of Consolidation ◽  
Excess Pore

Abstract The objective of this study was to predict the excess pore pressure and settlement of an embankment over soft ground, treated with vertical drain, through numerical analysis of staged construction. To carry out finite element analysis, numerical modeling software PLAXIS 3D was used. The practical demonstration was demonstrated by validating two case studies; the first one was a trial embankment at the Krishnapatnam Ultra Mega Power Project in Nellore, Andhra Pradesh, India and the second one was the Second Bangkok International Airport or Suvarnabhumi Airport, about 30 km from the city of Bangkok, Thailand. After the successful validation of the program, detailed finite element modelling of an embankment resting on soft soil was conducted. Moreover, the degree of consolidation and factor of safety were also determined. There was rapid dissipation of excess pore pressure and maximum settlement at the mid-height of the embankment. In contrast, the dissipation of excess pore pressure was very slow just below the embankment and it increased with the increment of the depth of the clay layer. Moreover, with the rise of the distance from the centre of the embankment, the dissipation of the excess pore pressure also raised and took less time, the settlement also increased.

scholarly journals Comparison of Coupled and Uncoupled Consolidation Equations Using Finite Element Method in Plane-Strain Condition

2016 ◽  
Vol 2 (8) ◽  
pp. 375-388 ◽  
Author(s):  
Mohamadtaqi Baqersad ◽  
Abbas Eslami Haghighat ◽  
Mohammadali Rowshanzamir ◽  
Hamid Mortazavi Bak
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Pore Pressure ◽  
Effective Stress ◽  
Excess Pore Pressure ◽  
Soil Deformation ◽  
Soil Consolidation ◽  
Time Step ◽  
Excess Pore ◽  
Element Method

In the current paper, the consolidation settlement of a strip footing over a finite layer of saturated soil has been studied using the finite element method. In Biot’s coupled consolidation equations, the soil deformation and excess pore pressure are determined simultaneously in every time step which refers to the hydro-mechanical coupling. By considering a constant total stress throughout the time and by assuming that volume strain is a function of isotropic effective stress, uncoupled consolidation equations can be obtained using coupled consolidation equations. In these uncoupled equations, excess pore pressure and deformation are determined separately. In this approach, the excess pore pressure can be identified in the first stage. Using the calculated excess pore pressure, the soil deformation is determined through effective stress-strain analyses. A computer code was developed based on coupled and uncoupled equations that are capable of performing consolidation analyses. To verify the accuracy of these analyses, the obtained results have been compared with the precise solution of Terzaghi’s one-dimensional consolidation theory. The capability of these two approaches in estimation of pore water pressure and settlement and to show Mandel-Crayer’s effect in soil consolidation is discussed. Then, the necessity of utilizing coupled analyses for evaluating soil consolidation analysis was investigated by comparing the coupled and uncoupled analyses results.

scholarly journals A laboratory study of particle ploughing and pore-pressure feedback: a velocity-weakening mechanism for soft glacier beds

2008 ◽  
Vol 54 (184) ◽  
pp. 169-181 ◽  
Author(s):  
Jason F. Thomason ◽  
Neal R. Iverson
Keyword(s):  
Pore Pressure ◽  
Water Discharge ◽  
Fold Increase ◽  
Excess Pore Pressure ◽  
Measured Velocity ◽  
Pore Pressures ◽  
Pressure Diffusion ◽  
Pressure Feedback ◽  
Excess Pore Pressures ◽  
Excess Pore

AbstractIf basal-water discharge and pressure are sufficiently high, a soft-bedded glacier will slip over its bed by ploughing, the process in which particles that span the ice–bed interface are dragged across the bed surface. Results of laboratory experiments indicate that resistance to ploughing can decrease with increasing ploughing velocity (velocity weakening). During ploughing at various velocities (15–400 m a−1), till was compacted in front of idealized particles, causing pore pressures there that were orders of magnitude higher than the ambient value. This excess pore pressure locally weakened the till in shear, thereby decreasing ploughing resistance by a factor of 3.0–6.6 with a six-fold increase in ploughing velocity. Characteristic timescales of pore-pressure diffusion and compaction down-glacier from ploughing particles depend on till diffusivity, ploughing velocity and sizes of ploughing particles. These timescales accurately predict the ranges of these variables over which excess pore pressure and velocity weakening occurred. Existing ploughing models do not account for velocity weakening. A new ploughing model with no adjustable parameters predicts ploughing resistance to no worse than 38% but requires that excess pore pressures be measured. Velocity weakening by this mechanism may affect fast glacier flow, sediment transport by bed deformation and basal seismicity.

Inclined Perimeter Drains Performance as Liquefaction Countermeasure Techniques Below Existing Buildings

2020 ◽  
Vol 14 (03) ◽  
pp. 2050015
Author(s):  
Samy Garcıáa-Torres ◽  
Gopal Santana Phani Madabhushi
Keyword(s):  
Pore Pressure ◽  
Structural Damage ◽  
Excess Pore Pressure ◽  
Existing Buildings ◽  
Ground Shaking ◽  
Vertical Drains ◽  
Centrifuge Tests ◽  
Pore Pressures ◽  
Excess Pore Pressures ◽  
Excess Pore

Reducing the risk of structural damage due to earthquake-induced liquefaction in new and existing buildings is a challenging problem in geotechnical engineering. Drainage countermeasure techniques against liquefaction have been studied over the last decades with an emphasis on the use of vertical drains. This technique aims to allow a rapid dissipation of excess pore pressures generated in the soil during the earthquake thereby limiting the peak excess pore pressures and consequently improve the structural response. Rapid drainage in the post-earthquake period in the presence of these drains helps quick recovery of the soil strength. Recent studies propose different variations in the vertical drains arrangement to improve the excess pore pressure redistribution in the soil around structures. However, conventional arrangements for existing buildings do not achieve an adequate proximity from the drains to the soil below the foundation. To address this, the performance of inclined and vertical perimeter drain arrangements are studied in this paper. Dynamic centrifuge tests were carried out for the different arrangements in order to evaluate the excess pore pressure generation due to ground shaking and the following dissipation together with the foundation settlement and dynamic response.

Sign in / Sign up

Export Citation Format

Share Document