Micro Quantity Internal Cooling (MQUIC™) of Cutting Tools for Increased Productivity While Machining Ti-6Al-4V

2010 ◽  
Author(s):  
Samved Bhatnagar ◽  
William J. Endres
Keyword(s):  
Tool Life ◽  
Unit Cost ◽  
Cutting Tools ◽  
Cutting Speed ◽  
High Strength ◽  
Internal Cooling ◽  
Wear Rates ◽  
Industry Standard ◽  
Tool Performance ◽  
Cutting Speeds

Machining of space age materials like Ti-6Al-4V is associated with thermally activated wear mechanisms which lead to rapid tool failure and increased machine downtime. The high strength and low thermal conductivity of Ti-6Al-4V can reduce tool-life significantly at high cutting speeds adding drastically to the per-unit cost. A new concept, Micro Quantity Internal Cooling (MQUIC™) has been developed to extend the tool-life and/or enable higher cutting speeds while machining Ti-6Al-4V. The concept involves introducing flow (coolant) in a micro-duct placed inside the tool and close to the cutting edge, thus bringing the cooling source close to the heat source (chip-contact area). In this research, experiments have been conducted to compare the performance (wear rates) of cutting tools using the MQUIC™ concept with those run under dry or flood conditions. Further, two levels of feed and cutting speed are selected for the experiments so as to be able to investigate the combined effect of parameters on tool performance. Physical testing employing coolant consumption of less than 5% of typical flood coolant rates proves the viability of the concept by demonstrating wear rates of 1/3 to 1/2 those of flood cooling. The testing also proves the application of the MQUIC™ concept to enable higher cutting speeds than the current industry standard for machining Ti-6Al-4V. This paper presents the experimental setup, methodology and results obtained while testing the feasibility of the concept.

scholarly journals Investigation into Performance of Multilayer Composite Nano-Structured Cr-CrN-(Cr0.35Ti0.40Al0.25)N Coating for Metal Cutting Tools

Coatings ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 447 ◽  
Author(s):  
Sergey Grigoriev ◽  
Alexey Vereschaka ◽  
Alexander Metel ◽  
Nikolay Sitnikov ◽  
Filipp Milovich ◽  
...  
Keyword(s):  
Tool Life ◽  
Metal Cutting ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Constructional Steel ◽  
Wear Process ◽  
Layered Architecture ◽  
Process Pattern ◽  
Resistant Layer ◽  
Cutting Speeds

This paper deals with the Cr-CrN-(Cr0.35Ti0.40Al0.25)N coating. It has a three-layered architecture with a nano-structured wear-resistant layer. The studies involved the investigation into the microstructure (with the use of SEM and TEM), elemental and phase composition (XRD and SAED patterns), wear process pattern in scratch testing, crystal structure, as well as the microhardness of the coating. Cutting tests of tools with the above coating were carried out in dry turning of steel 1045 at cutting speeds of vc = 200, 250, and 300 m·min−1. The comparison included uncoated tools and tools with the commercial TiN and (Ti,Al)N coatings with the same thickness. The tool with the Cr-CrN-(Cr0.35Ti0.40Al0.25)N coating showed the longest tool life at all the cutting speeds under consideration. Meanwhile, a tool with the coating under study can be recommended for use in turning constructional steel at the cutting speed of vc = 250 m·min−1. At this cutting speed, a tool shows the combination of a rather long tool life and balanced wear process, without any threat of catastrophic wear.

scholarly journals Analysis of the General Tool Life Function of Cutting Tools by Application of the Catastrophe-Theory

2021 ◽  
Author(s):  
Zoltán Pálmai ◽  
János Kundrák ◽  
Csaba Felhő
Keyword(s):  
Tool Life ◽  
Catastrophe Theory ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Taylor Formula ◽  
Technology Planning ◽  
Concave Part ◽  
Cutting Speeds ◽  
General Tool ◽  
Life Function

Abstract Production technology planning requires information on tool life T and its relation to cutting speed v. As the Taylor formula often cannot be linearized on an lg-lg scale, a general tool life function has been developed for describing a v-T function with a convex-concave part. Using catastrophe theory, an analogy is established between the general tool life function and the cusp catastrophe, allowing topological mapping of the general v-T function. Results were verified by machinability tests in the turning of C35 and C60 conventional and specially deoxidized C-steels during steelmaking. It was found that in the convex-concave section of this function, 2–3 cutting speeds can be selected for a given tool life, which is advantageous for harmonizing tool changes in multi-operation technology.

scholarly journals Alternative Binder Carbide Tools for Machining Superalloys

2008 ◽  
Author(s):  
Daniel Waldorf ◽  
Scott Liu ◽  
Michael Stender ◽  
Daniel Norgan
Keyword(s):  
Wear Resistance ◽  
Tool Life ◽  
Cutting Tools ◽  
Cutting Speed ◽  
New Class ◽  
Nickel Based Superalloy ◽  
Composite Tool ◽  
Binder Composition ◽  
Positive Effect ◽  
Cutting Speeds

This study examines the performance of a new class of wear-resistant but economical cutting tools produced by varying the binder composition of standard cemented carbide composites. By replacing some or all of the cobalt binder with rhenium and nickel-based superalloy, a stronger composite tool results, potentially capable of machining heat-resistant superalloys at significantly higher cutting speeds. Sample tools with alternative binder were produced and compared to standard tools bound with cobalt only. Turning experiments on Inconel 718 were run to evaluate wear resistance and tool life for several grades. The experimentation also examined the effects of varying the relative proportions of each binder constituent as well as the overall binder percentage in the composite. Results show a clear advantage of the alternative binder tools as evidenced by a 150% increase in tool life or the equivalent of an 18% increase in cutting speed. Although increasing amounts of rhenium in the binder show a positive effect on performance, the effects of superalloy and overall binder % are inconclusive.

Development of Cutting Tools With Micro-Textured Surface for High Speed Machining of Ti-6Al-4V

2021 ◽  
Author(s):  
Mitsuru Hasegawa ◽  
Tatsuya Sugihara
Keyword(s):  
Tool Life ◽  
High Speed ◽  
Metal Cutting ◽  
Failure Process ◽  
Cutting Tools ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Fluid ◽  
Textured Surface ◽  
Textured Surfaces

Abstract In cutting of Ti-6Al-4V alloy, the cutting speed is limited since a high cutting temperature leads to severe tool wear and short tool life, resulting in poor production efficiency. On the other hand, some recent literature has reported that various beneficial effects can be provided by forming micro-textures on the tool surface in the metal cutting process. In this study, in order to achieve high-performance machining of Ti-6Al-4V, we first investigated the mechanism of the tool failure process for a cemented carbide cutting tool in high-speed turning of Ti-6Al-4V. Based on the results, cutting tools with micro textured surfaces were developed under the consideration of a cutting fluid action. A series of experiments showed that the textured rake face successfully decreases the cutting temperature, resulting in a significant suppression of both crater wear and flank wear. In addition, the temperature zone where the texture tool is effective in terms of the tool life in the Ti-6Al-4V cutting was discussed.

scholarly journals Threading Performance of Different Coatings for High Speed Steel Tapping

Coatings ◽  
2020 ◽  
Vol 10 (5) ◽  
pp. 464
Author(s):  
Alain Gil Del Val ◽  
Fernando Veiga ◽  
Octavio Pereira ◽  
Luis Norberto Lopez De Lacalle
Keyword(s):  
Tool Life ◽  
Vapor Deposition ◽  
Physical Vapor Deposition ◽  
High Speed ◽  
Cutting Speed ◽  
High Speed Steel ◽  
Tialn Coating ◽  
Tool Performance ◽  
Thread Profile ◽  
Increase Tool Life

Threading holes using tapping tools is a widely used machining operation in the industry. This manufacturing process involves a great tool immersion in the part, which involves both friction and cutting. This makes the use of coatings critical to improving tool life. Four coatings are used based on Physical vapor deposition (PVD) technology—TiN, TiCN, TiAlN and TiAlN+WC/C are compared to uncoated tool performance. The effect of various coatings on the life of M12 × 1.5 tapping tools during threading of through holes 20 mm deep, in GG25 casting plates, dry and applying cutting speed of 50 m/min. The end-of-life criterion has been established based on a cutting torque of 16 N-m. Taking the uncoated tap as a basis for comparison, it is observed that coatings based on PVD technologies increase tool life doubling in the most advantageous case with the TiAlN coating. PVD type coatings provide better protection to wear at cylindrical area of the tool, where the thread profile is finished, than uncoated taps. The teeth located in the cone-cylinder transition zone of the taps suffer the most wear regardless of the coating. However, taps coated with TiAlN+WC/C wear level values is lowest of all the coatings tested, which indicates a strong reinforcement in these teeth.

scholarly journals Tribological Investigations of PVD Coated Multi-Layer Constructions

2015 ◽  
Vol 5 (1) ◽  
pp. 97 ◽  
Author(s):  
Marcus Schulze ◽  
Holger Seidlitz ◽  
Franziska Konig ◽  
Sabine WeiB
Keyword(s):  
Carbon Fibre ◽  
Physical Vapor Deposition ◽  
Large Scale ◽  
Metal Cutting ◽  
Wear Behavior ◽  
Cutting Tools ◽  
Weight Ratio ◽  
High Strength ◽  
Coating System ◽  
Wear Rates

<p class="1Body">Multi-layer constructions become more and more relevant in lightweight applications due to their high strength to weight ratio. They offer excellent crash, damping and recycling properties. Also, the morphology of thermoplastic carbon fibre reinforced plastics (CFRP) render them interesting for large scale manufacturing processes. Nevertheless, a major disadvantage results in a poor resistance against wear and tear, e.g. erosion, which is attributed to weak hardness properties. Hence, this work deals with tribological investigations on orthotropic carbon fibre reinforced polymers (PA 6) either with protective ceramic coating or without. The chosen coating system is a well-known protective covering of metal components, e.g. metal cutting tools, produced by physical vapor deposition (PVD). To characterize the coating system on thermoplastic CFRP, standard analyzing methods are utilized, like optical and scanning electron microscopy (SEM). The tribological investigations are conducted by the tribological ball on disk method to generate wear tracks on the sample surfaces and hence to calculate the wear rates. These results are compared to literature findings with respect to a certain protective coating system (TiN) and a second nano-structured gel coating system, where both systems are deposited on a thermosetting material, i.e. carbon fibre reinforced epoxy resin, respectively. For this purpose the feasibility of depositing a protective ceramic layer on thermoplastic CFRP is demonstrated. First results on suitable surface pre-treatments have shown a significant influence on the coating quality. The improved performance regarding the wear behavior with respect to tribology compared to the poor substrate and existing technologies is shown additionally.</p>

Comparative Experimental Research on Cutting Superalloy Used New Coated Carbide Tools

2010 ◽  
Vol 33 ◽  
pp. 173-176
Author(s):  
X.Y. Wang ◽  
S.Q. Pang ◽  
Q.X. Yu
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Experimental Research ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Life Testing ◽  
Processing Efficiency ◽  
Comparative Tests ◽  
Coated Carbide ◽  
Coated Carbide Tools

The aim of this work is to investigate the machinability of new coated carbide cutting tools that are named C7 plus coatings under turning of superalloy GH2132. This achieved by analysis of tool life at different cutting conditions .Investigations of tool wear and tool life testing are intended to establish T-V formulas, and then analyzed the characteristics of coating . Through a series of comparative tests, Using TiAlN coatings as the contrast materialthe results show that the new coating tools that are named C7 plus coatings are suitable for cutting superalloy GH2132. The cutting speed and processing efficiency can be increased effectively.

The Effect of Tool Edge Geometry on Tool Performance and Surface Integrity in Turning Ti-6Al-4V Alloys

2011 ◽  
Vol 264-265 ◽  
pp. 1211-1221 ◽  
Author(s):  
Yanuar Burhanuddin ◽  
Che Hassan Che Haron ◽  
Jaharah A. Ghani
Keyword(s):  
Tool Life ◽  
Surface Integrity ◽  
Feed Rate ◽  
Cutting Speed ◽  
Optical Microscope ◽  
Edge Geometry ◽  
Tool Performance ◽  
Tool Edge ◽  
Structural Deformations ◽  
Notch Wear

This paper focuses on the influence of cutting tool edge geometry, cutting speed and feed rate on the tool performance and workpiece’s surface integrity in dry turning of Ti-6Al-4V alloy using PCBN inserts. The parameters evaluated are tool life, wear rate, wear mechanisms, surface roughness and subsurface microstructure alterations. The rate of wear growth of the insert was assessed by progressive flank wear using optical microscope by taking photographs after certain length of cut. The wear mechanism at the end of tool life was investigated in detail using scanning electron microscope (SEM) and EDAX analysis. The results show, by increasing the cutting speed and feed rate resulted in tool life reduction. Cutting with honed edge insert at cutting speed of 180 m/min has shown very little wear, even after 20 min of cutting. The honed insert proved less sensitive to increases in feed rate than the chamfered insert. In general the honed insert showed a significant improvement in tool life. All inserts failed due to attrition wear and adhesion. No flank notch wear was observed, but some crater wear occurred at the chamfer land. Microstructure alteration was not found when machining using the different edge geometry. In these trials, the subsurface micro structural deformations in the direction of cutting were deformed grain boundaries and elongation of grains. Chip smearing and debris on the surface was also found.

The Effect of Cut Tool Geometric Parameters on Tool Tear of Machining Nickel-Base GH4169 Super Alloys

2010 ◽  
Vol 37-38 ◽  
pp. 1457-1461 ◽  
Author(s):  
Zhao Peng Hao ◽  
D. Gao ◽  
R.D. Han
Keyword(s):  
Tool Life ◽  
Cutting Speed ◽  
High Strength ◽  
Rake Angle ◽  
Geometric Parameters ◽  
Cutting Edge ◽  
Factors Affecting ◽  
Edge Angle ◽  
Coated Tools ◽  
Nickel Base

Nickel-based super alloy GH4169 has been widely used in aerospace industry because of its good mechanical properties under high temperature. However, it is difficult to machine for its high strength, poor thermal conductivity and serious work-hardening. The effects of tool geometric parameters on tool life are studied by machining experiments using YG8 tools with different cutting edge angle in this paper. The tool with cutting edge angle 45°has longer tool life than 75°. The cutting experiments have been carried out using TiAlN (PVD) coated tools (AC520U) with different rake angle. It shows that the tool life with rake angle 9° were increased by 50% and 25% compared to tool with rake angle 3°and 6° when cutting speed is 30m/min. The tool with rake angle 9° is not suitable for cutting GH4169 when cutting speed is more than 35m/min. The results show that geometric parameter of cutting tool is one of the important factors affecting tool life.

A Stochastic Tool-Life Model

1981 ◽  
Vol 103 (1) ◽  
pp. 126-130 ◽  
Author(s):  
S. Rossetto ◽  
A. Zompi
Keyword(s):  
Stochastic Model ◽  
Failure Rate ◽  
Tool Life ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Cutting Edge ◽  
Model Based ◽  
Life Model ◽  
Theoretical Standpoint

A tool-life model based on the assumption that wear and fracture are the causes of tool death is re-examined from the theoretical standpoint, and extended to include the effect of cutting speed on the fracture-induced failure rate. A stochastic model for multi edge cutting tools is also proposed. This enables the overall statistics to be derived from the data for each individual cutting edge.

Sign in / Sign up

Export Citation Format

Share Document