Qualification of an Application System for In-Field External Reinforcement of Pipelines Using Helical Steel Wrap

2012 ◽  
Author(s):  
David J. Miles
Keyword(s):  
Steel Strip ◽  
Axial Strain ◽  
High Strength ◽  
Operating Pressure ◽  
Element Analysis ◽  
Application System ◽  
Location Class ◽  
External Reinforcement ◽  
Class 1 ◽  
Welded Pipe

A solution, known as XHab™, has been developed for external repair and reinforcement of pipelines using ultra high strength steel strip. This method involves wrapping multiple layers of strip in a helical form continuously over an extended length of pipeline using a dedicated forming and wrapping machine. The reinforcement provided by the strip can be used to: a) Restore the original maximum allowable operating pressure to a section of defective pipe (e.g. external corrosion or denting), or b) Reinforce an intact but de-rated section of pipeline (e.g. a Location Class change through encroachment) to maintain reduced hoop stress in the base pipe as required by codes and regulations, but allow reinstatement of the original operating pressure by carrying the additional load in the strips. This paper describes the full-scale qualification testing, including in-field proving runs, and design analysis necessary to demonstrate the field-readiness of the application system and reinforcement product. This includes wrapping and pressure testing of pipe with machined external wall defects. The potential for XHab repair of stress corrosion cracking (SCC) is also discussed for an upcoming series of tests on pipe samples with electrical discharge machined notches. To demonstrate reinforcement of intact pipe, a 40ft joint of 26-inch vintage flash-butt seam welded pipe, instrumented with hoop and axial strain gages, has been wrapped by the XHab machine with sufficient reinforcement to simulate a change from Location Class 1, Div. 2 to Location Class 3 (ASME B31.8). This pipe has been subjected to pressure cycling and ultimate burst alongside an identical unwrapped pipe sample which provides a baseline. The test results are presented and compared to finite element analysis.

In-Field Application of Steel Strip Reinforcement for Pipeline External Rehabilitation

2010 ◽  
Author(s):  
Nicholas J. Venero ◽  
Tim J. M. Bond ◽  
Raymond N. Burke ◽  
David J. Miles
Keyword(s):  
Steel Strip ◽  
New Technology ◽  
High Strength ◽  
Field Application ◽  
Operating Conditions ◽  
Operating Pressure ◽  
Precise Control ◽  
Ultra High Strength Steel ◽  
Structural Adhesive ◽  
Pipeline Design

A new technology for external rehabilitation of pipelines, known as XHab™, has been developed. This method involves wrapping multiple layers of ultra-high strength steel (UHSS) strip in a helical form continuously over an extended length of pipeline using a dedicated forming and wrapping machine. The reinforcement afforded by the strip can be used to bring a defective section of pipe (e.g. externally corroded or dented) back to its original allowable operating conditions, or even to increase the allowable operating pressure if the desired operating conditions exceed the original pipeline design limits. This paper describes the design, manufacture and testing process for a self-propelled wrapping machine for in-field rehabilitation. The wrapping apparatus consists of several major components including an opening sufficiently wide to receive the pipe, a movement assembly, a winding head, a preforming device, an accumulator and an oscillating adhesive applicator. The wrapping apparatus uses the winding head to wrap the reinforcing steel strip around the pipe. The movement assembly uses a pair of tracks in contact with the pipe to drive the wrapping apparatus along which enables helical wrapping of the reinforcing strip material. The oscillating adhesive assembly applies structural adhesive to the pipe immediately before the strip is wound. The winding head, motive assembly and adhesive applicator are electronically synchronized to one another to enable precise control of pitch and adhesive volume. The paper also describes the field application of XHab including mobilization/demobilization of equipment and interaction with other rehabilitation equipment, as well as specific aspects such as initiation and termination of wrapping, protection of rehabilitated area and implementation of cathodic protection.

Testing and Analysis of Steel Strip Reinforcement for Pipeline External Rehabilitation

2010 ◽  
Author(s):  
David J. Miles ◽  
Tim J. M. Bond ◽  
Raymond N. Burke ◽  
Ruben van Schalkwijk
Keyword(s):  
Steel Strip ◽  
New Technology ◽  
High Strength ◽  
Full Scale ◽  
Operating Conditions ◽  
Operating Pressure ◽  
Batch Tests ◽  
Girth Welds ◽  
The Individual ◽  
Pipeline Design

A new technology for external rehabilitation of pipelines, known as XHab™, has been developed. This method involves wrapping multiple layers of ultra-high strength steel strip (UHSS) in a helical form continuously over an extended length of pipeline using a dedicated forming and wrapping machine. The reinforcement afforded by the strip can be used to bring a defective section of pipe (e.g. externally corroded or dented) back to its original allowable operating conditions, or even to increase the allowable operating pressure if the desired operating conditions exceed the original pipeline design limits. This paper describes the full scale burst testing and analysis of defective pipes which have been repaired using the XHab process. The full scale test sections are 30″ × 0.5″ API 5L X52 DSAW pipe and include the following specimens: • Bare pipe with no defects; • Bare pipe with single machined defect; • Wrapped pipe with single machined defect and designed reinforcement; • Wrapped pipe with single machined defect and insufficient reinforcement; • Wrapped pipe with interacting defect array and designed reinforcement. The above full scale burst tests are supplemented by FEA models using ABAQUS. The material models for the steel pipe, UHSS strip, defect patch material and strip adhesive are based on measured data from the batch tests and tuned against the control burst test results. The structural behavior in the individual metallic and non-metallic elements can therefore be examined more closely, particularly in the region of the defect and where the wrapped strip crosses seam and girth welds.

scholarly journals Finite Element Modelling of RC T - Beams Reinforced Internally with GFRP Reinforcements

2019 ◽  
Vol 5 (3) ◽  
pp. 563
Author(s):  
Balamuralikrishnan R. ◽  
Saravanan J.
Keyword(s):  
Finite Element ◽  
Corrosion Resistance ◽  
Research Work ◽  
High Strength ◽  
Light Weight ◽  
Reinforced Concrete Structure ◽  
Element Analysis ◽  
Existing Structures ◽  
External Reinforcement ◽  
Bridge Structures

Fibre reinforced polymers (FRP) are being used extensively in the rehabilitation and retrofitting of existing structures  as an external reinforcement because of their properties like high strength to weight and stiffness to weight  ratios, corrosion resistance, light weight and high durability. They are especially used in the reinforced concrete structure like bridges, chimney, high rise building etc. At present FRP reinforcements are available in the form of reinforcing bars and are used in the structures in place of steel, mainly the structures are constructed near the coastal areas or in the aggressive environments. The main advantage of FRP rebar is its corrosion resistance, light weight, durability and easy handing. The FRP rebars are being used worldwide for many structures including bridge structures as well, but not well explored because of its availability. The main objective of this thesis work is to assess the static load behaviour of RC T-beams reinforced internally with GFRP reinforcements using finite element analysis software ANSYS. Totally twelve numbers of specimens were considered in this study with varying parameters such as type of reinforcements, reinforcements ratio and concrete grade. Modelling of the T- beams were done with ANSYS using solid 65 and link 8 element and the same were analyzed under static loading conditions. The results obtained from the ANSYS were compared with the theoretical and experimental analysis. Based on the comparison suitable conclusions and recommendations are made in this research work.

scholarly journals Failure Analysis on a Collapsed Flat Cover of an Adjustable Ballast Tank Used in Deep-Sea Submersibles

2019 ◽  
Vol 9 (23) ◽  
pp. 5258
Author(s):  
Fang Wang ◽  
Mian Wu ◽  
Genqi Tian ◽  
Zhe Jiang ◽  
Shun Zhang ◽  
...  
Keyword(s):  
Deep Sea ◽  
Material Selection ◽  
High Strength ◽  
External Pressure ◽  
Element Analysis ◽  
Ballast Tank ◽  
Material Inhomogeneity ◽  
Comprehensive Properties ◽  
Ultimate Cause ◽  
Flat Cover

A flat cover of an adjustable ballast tank made of high-strength maraging steel used in deep-sea submersibles collapsed during the loading process of external pressure in the high-pressure chamber. The pressure was high, which was the trigger of the collapse, but still considerably below the design limit of the adjustable ballast tank. The failure may have been caused by material properties that may be defective, the possible stress concentration resulting from design/processing, or inappropriate installation method. The present paper focuses on the visual inspections of the material inhomogeneity, ultimate cause of the collapse of the flat cover in pressure testing, and finite element analysis. Special attention is paid to the toughness characteristics of the material. The present study demonstrates the importance of material selection for engineering components based on the comprehensive properties of the materials.

A modified physical model of high-strength water hydraulic artificial muscles considering the effects of geometry and material properties

2021 ◽  
pp. 095440622199907
Author(s):  
Zengmeng Zhang ◽  
Jinkai Che ◽  
Peipei Liu ◽  
Yunrui Jia ◽  
Yongjun Gong
Keyword(s):  
Physical Model ◽  
Relative Error ◽  
Wall Thickness ◽  
Material Properties ◽  
High Strength ◽  
Artificial Muscles ◽  
Operating Pressure ◽  
Rubber Tube ◽  
Contraction Ratio ◽  
Water Hydraulic

Compared with pneumatic artificial muscles (PAMs), water hydraulic artificial muscles (WHAMs) have the advantages of high force/weight ratio, high stiffness, rapid response speed, large operating pressure range, low working noise, etc. Although the physical models of PAMs have been widely studied, the model of WHAMs still need to be researched for the different structure parameters and work conditions between PAMs and WHAMs. Therefore, the geometry and the material properties need to be considered in models, including the wall thickness of rubber tube, the geometry of ends, the elastic force of rubber tube, the elongation of fibers, and the friction among fiber strands. WHAMs with different wall thickness and fiber materials were manufactured, and static characteristic experiments were performed when the actuator is static and fixed on both ends, which reflects the relationship between contraction force and pressure under the different contraction ratio. The deviations between theoretical values and experimental results were analyzed to investigate the effect of each physical factor on the modified physical model accuracy at different operating pressures. The results show the relative error of the modified physical model was 7.1% and the relative error of the ideal model was 17.4%. When contraction ratio is below 10% and operating pressure is 4 MPa, the wall thickness of rubber tube was the strongest factor on the accuracy of modified model. When the WHAM contraction ratio from 3% to 20%, the relative error between the modified physical model and the experimental data was within ±10%. Considering the various physical factors, the accuracy of the modified physical model of WHAM is improved, which lays a foundation of non-linear control of the high-strength, tightly fiber-braided and thick-walled WHAMs.

Accelerated testing of super lightweight UHPC waffle deck under heavy vehicle simulator

2021 ◽  
Vol 16 (2-3) ◽  
pp. 61-74
Author(s):  
Sahar Ghasemi ◽  
Amir Mirmiran ◽  
Yulin Xiao ◽  
Kevin Mackie
Keyword(s):  
High Performance ◽  
Failure Modes ◽  
High Performance Concrete ◽  
High Strength ◽  
Heavy Vehicle ◽  
Wheel Load ◽  
Element Analysis ◽  
Vehicle Simulator ◽  
Pavement Testing ◽  
Heavy Vehicle Simulator

A super lightweight deck can enhance load rating and functionality of a bridge, especially those identified as structurally deficient. This study was aimed to develop and experimentally validate a novel bridge deck as an ultra-lightweight low-profile waffle slab of ultra-high-performance concrete (UHPC) with either carbon fiber reinforced polymer (CFRP) or high strength steel (HSS) reinforcement. The proposed system lends itself to accelerated bridge construction, rapid deck replacement in bridges with load restrictions, and bridge widening applications without the need to replace girders. Performance and failure modes of the proposed deck were initially assessed through extensive lab experiments and finite element analysis, which together confirmed that the proposed deck panel meets the AASHTO LRFD requirements. The proposed deck system is not susceptible to punching shear of its thin slab and fails in a rather ductile manner. To evaluate its long-term performance, the system was further tested under the dynamic impact of wheel load at the Accelerated Pavement Testing (APT) facility of the Florida Department of Transportation using a Heavy Vehicle Simulator (HVS).

scholarly journals Multi-Stage Cold Forging Process for Manufacturing a High-Strength One-Body Input Shaft

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 532
Author(s):  
A Jo ◽  
Myeong Jeong ◽  
Sang Lee ◽  
Young Moon ◽  
Sun Hwang
Keyword(s):  
High Strength ◽  
Microstructural Characterization ◽  
Fatigue Tests ◽  
Machining Process ◽  
Cold Forging ◽  
Element Analysis ◽  
Forging Process ◽  
Input Shaft ◽  
Multi Stage ◽  
The One

A multi-stage cold forging process was developed and complemented with finite element analysis (FEA) to manufacture a high-strength one-body input shaft with a long length body and no separate parts. FEA showed that the one-body input shaft was manufactured without any defects or fractures. Experiments, such as tensile, hardness, torsion, and fatigue tests, and microstructural characterization, were performed to compare the properties of the input shaft produced by the proposed method with those produced using the machining process. The ultimate tensile strength showed a 50% increase and the torque showed a 100 Nm increase, confirming that the input shaft manufactured using the proposed process is superior to that processed using the machining process. Thus, this study provides a proof-of-concept for the design and development of a multi-stage cold forging process to manufacture a one-body input shaft with improved mechanical properties and material recovery rate.

Benefits of Using Diamond Dies for Cold Alternate Drawing of Magnesium Alloys

2016 ◽  
Vol 716 ◽  
pp. 13-21 ◽  
Author(s):  
Vladimir Stefanov Hristov ◽  
Kazunari Yoshida
Keyword(s):  
Magnesium Alloy ◽  
Weight Ratio ◽  
High Strength ◽  
Wire Drawing ◽  
High Ductility ◽  
Element Analysis ◽  
The Wire ◽  
Shearing Strain ◽  
Drawing Method

In recent years, due to its low density and high strength/weight ratio, magnesium alloy wires has been considered for application in many fields, such as welding, electronics, medical field (for production of stents). But for those purposes, we need to acquire wires with high strength and ductility. For that we purpose we proposed alternate drawing method, which is supposed to highly decrease the shearing strain near the surface of the wire after drawing, by changing the direction of the wire drawing with each pass and thus acquiring high ductility wires.We have done research on the cold alternate drawing of magnesium alloy wires, by conducting wire drawing of several magnesium wires and testing their strength, hardness, structure, surface and also finite element analysis, we have proven the increase of ductility at the expense of some strength.In this research we are looking to further improve the quality of the drawn wires by examining the benefits of using diamond dies over tungsten carbine dies. Using the alternate drawing method reduces the strength of the drawn wires and thus lowering their drawing limit. By using diamond dies we are aiming to decrease the drawing stress and further increase the drawing limit of the alternate drawn wires and also improve the quality of the finishing surface of the wires. With this in mind we are aiming to produce a good quality wire with low diameter, high ductility, high strength and fine wire surface.

Sign in / Sign up

Export Citation Format

Share Document