An Evaluation of Auxiliary Part Configuration in the Micro Flow Sensor by Using Micro PIV

2005 ◽  
Author(s):  
Daichi Suzuki ◽  
Takashi Nagumo ◽  
Shinji Honami ◽  
Shoji Kamiunten
Keyword(s):  
Flow Field ◽  
Microfluidic Device ◽  
Flow Behavior ◽  
Flow Sensor ◽  
Sensing Element ◽  
Micro Particle Image Velocimetry ◽  
Micro Piv ◽  
Image Velocimetry ◽  
Bonding Wires ◽  
Micro Flow

The paper describes the configuration effects of the auxiliary parts on the flow behavior around the microfluidic device. Recent development of the devices in MEMS is noticeable. The devices are manufactured in more complicated configuration and arrangement with the auxiliary part for the requirement of higher performance. An evaluation of the flow field around the microfluidic device is strongly required in MEMS design. The aim of the paper is to clarify the effect of the auxiliary part arrangement on the flow field around the micro flow sensor which has both the sensing element and the auxiliary parts such as the pins, pillars and electric bonding wires. The flow around the sensor is measured by using the Micro Particle Image Velocimetry (PIV) system. We investigate four types of the micro flow sensor with different configuration and arrangement of the pin, the bonding wires and the pillars. The result shows that the effect of the supporting pillars is negligible.

Three-Dimensional Micro-Flow Measurement in a Capillary with a Diode Laser Micro-Particle Image Velocitometry

2006 ◽  
Vol 505-507 ◽  
pp. 343-348
Author(s):  
C.T. Pan ◽  
P.J. Cheng ◽  
Yeong-Maw Hwang ◽  
M.F. Chen ◽  
H.S. Chuang ◽  
...  
Keyword(s):  
Diode Laser ◽  
Particle Image ◽  
Three Dimensional ◽  
Calibration Method ◽  
Measurement Range ◽  
Scanning Method ◽  
Micro Particle Image Velocimetry ◽  
Micro Piv ◽  
Image Velocimetry ◽  
Micro Flow

A self-built micro-particle image velocimetry (micro-PIV) with a diode laser is established to measure the micro-fluidic phenomenon in a 100 μm rectangular capillary. By scanning method, a 3-D flow image with a flowrate of 0.3 μL/min is presented. With this calibration method, the measurement ability for 3-D micro-fluidic dynamics could be achieved. This technique also reveals its benefit and potential in metrology. Hence, it provides a helpful tool for Bio-MEMS research. The experiment is proceeded under laminar flow, Re= 0.011. The measurement range is ranging from 0.05μm/s to 4.3mm/s. The vector grid resolution is optimized to 2.5 μm.

Entrance Length Characteristics in Microchannels Using Micro-Particle Image Velocimetry

2007 ◽  
Author(s):  
Tariq Ahmad ◽  
Ibrahim Hassan ◽  
Roland Muwanga
Keyword(s):  
Particle Image Velocimetry ◽  
Flow Field ◽  
Particle Image ◽  
Working Fluid ◽  
Entrance Length ◽  
Number Range ◽  
Micro Particle Image Velocimetry ◽  
Micro Piv ◽  
Aspect Ratios ◽  
Image Velocimetry

An experimental study has been carried out to explore the laminar hydrodynamic development length in the entrance region of adiabatic square microchannels. Flow field measurements are acquired through the use of micro-Particle Image Velocimetry (micro-PIV), a non-intrusive particle tracking and flow observation technique. With the application of micro-PIV, entrance length flow field data is obtained for two different microchannel hydraulic diameters of 500 μm and 100 μm, both of which have cross-sectional aspect ratios of one. The working fluid is distilled water, and velocity profile data is acquired over a laminar Reynolds number range from 0 to 200. The test sections were designed as to provide a sharpedged microchannel inlet from an infinitely sized reservoir, at least 100 times wider and higher than the microchannel hydraulic diameter. Also, all microchannels have a length-to-diameter ratio of at least 100, to assure fully developed flow at the channel exit. The micro-PIV procedure is validated in the fully developed region with comparison to Navier-Stokes momentum equations. Good agreement was found with comparison to conventional entrance length correlations for ducts, and no influence of scaling was observed.

scholarly journals Numerical and Experimental Analyses of Three- Dimensional Unsteady Flow around a Micro-Pillar Subjected to Rotational Vibration

Micromachines ◽  
2018 ◽  
Vol 9 (12) ◽  
pp. 668 ◽  
Author(s):  
Kanji Kaneko ◽  
Takayuki Osawa ◽  
Yukinori Kametani ◽  
Takeshi Hayakawa ◽  
Yosuke Hasegawa ◽  
...  
Keyword(s):  
Flow Field ◽  
Moving Boundary ◽  
Three Dimensional ◽  
Steady Streaming ◽  
Micro Piv ◽  
Piv Measurement ◽  
Image Velocimetry ◽  
Measurement Tools ◽  
Rotational Vibration ◽  
Induced Flow

The steady streaming (SS) phenomenon is gaining increased attention in the microfluidics community, because it can generate net mass flow from zero-mean vibration. We developed numerical simulation and experimental measurement tools to analyze this vibration-induced flow, which has been challenging due to its unsteady nature. The validity of these analysis methods is confirmed by comparing the three-dimensional (3D) flow field and the resulting particle trajectories induced around a cylindrical micro-pillar under circular vibration. In the numerical modeling, we directly solved the flow in the Lagrangian frame so that the substrate with a micro-pillar becomes stationary, and the results were converted to a stationary Eulerian frame to compare with the experimental results. The present approach enables us to avoid the introduction of a moving boundary or infinitesimal perturbation approximation. The flow field obtained by the micron-resolution particle image velocimetry (micro-PIV) measurement supported the three-dimensionality observed in the numerical results, which could be important for controlling the mass transport and manipulating particulate objects in microfluidic systems.

Experimental Analysis of Microchannel Entrance Length Characteristics Using Microparticle Image Velocimetry

2010 ◽  
Vol 132 (4) ◽  
Author(s):  
Tariq Ahmad ◽  
Ibrahim Hassan
Keyword(s):  
Reynolds Number ◽  
Flow Field ◽  
Entrance Region ◽  
Working Fluid ◽  
Parallel Plates ◽  
Entrance Length ◽  
Number Range ◽  
Micro Piv ◽  
Image Velocimetry ◽  
Microparticle Image Velocimetry

The study of the entrance region of microchannels and microdevices is limited, yet important, since the effect on the flow field and heat transfer mechanisms is significant. An experimental study has been carried out to explore the laminar hydrodynamic development length in the entrance region of adiabatic square microchannels. Flow field measurements are acquired through the use of microparticle image velocimetry (micro-PIV), a nonintrusive particle tracking and flow observation technique. With the application of micro-PIV, entrance length flow field data are obtained for three different microchannel hydraulic diameters of 500 μm, 200 μm, and 100 μm, all of which have cross-sectional aspect ratios of 1. The working fluid is distilled water, and velocity profile data are acquired over a laminar Reynolds number range from 0.5 to 200. The test-sections were designed as to provide a sharp-edged microchannel inlet from a very large reservoir at least 100 times wider and higher than the microchannel hydraulic diameter. Also, all microchannels have a length-to-diameter ratio of at least 100 to assure fully developed flow at the channel exit. The micro-PIV procedure is validated in the fully developed region with comparison to Navier–Stokes momentum equations. Good agreement was found with comparison to conventional entrance length correlations for ducts or parallel plates, depending on the Reynolds range, and minimal influence of dimensional scaling between the investigated microchannels was observed. New entrance length correlations are proposed, which account for both creeping and high laminar Reynolds number flows. These correlations are unique in predicting the entrance length in microchannels and will aid in the design of future microfluidic devices.

Infrared Micro-Particle Image Velocimetry of Fluid Flow in Silicon-Based Microdevices

Volume 4 ◽  
2004 ◽  
Author(s):  
Dong Liu ◽  
Suresh V. Garimella ◽  
Steve T. Wereley
Keyword(s):  
Particle Image Velocimetry ◽  
Particle Image ◽  
Capillary Tube ◽  
Surface Flow ◽  
Mems Devices ◽  
Flow Measurements ◽  
Micro Particle Image Velocimetry ◽  
Micro Piv ◽  
Image Velocimetry ◽  
Silicon Based

A non-intrusive diagnostic technique, infrared micro-particle image velocimetry (IR-PIV), is developed for measuring flow fields within MEMS devices with micron-scale resolution. This technique capitalizes on the transparency of silicon in the infrared region, and overcomes the limitation posed by the lack of optical access with visible light to sub-surface flow in silicon-based micro-structures. Experiments with laminar flow of water in a circular micro-capillary tube of hydraulic diameter 255 μm demonstrate the efficacy of this technique. The experimental measurements agree very well with velocity profiles predicted from laminar theory. Cross-correlation and auto-correlation algorithms are employed to measure very-low and moderate-to-high velocities, respectively; the former approach is suitable for biomedical applications while the latter would be needed for measurements in electronics cooling. The results indicate that the IR-PIV technique effectively extends the application of regular micro-PIV techniques, and has great potential for flow measurements in silicon-based microdevices.

scholarly journals Numerical simulation and in vitro examination of the flow behaviour within coronary stents

2019 ◽  
Vol 5 (1) ◽  
pp. 541-544
Author(s):  
Helena-Sophie Melzer ◽  
Ralf Ahrens ◽  
Andreas E. Guber ◽  
Jakob Dohse
Keyword(s):  
Design Parameters ◽  
Experimental Investigations ◽  
Metallic Stent ◽  
Flow Measurements ◽  
Micro Particle Image Velocimetry ◽  
Micro Piv ◽  
Stent Restenosis ◽  
Image Velocimetry ◽  
Stent Strut

AbstractThis paper discusses the influence of different design parameters of stents by mathematical flow simulations and flow measurements using micro-particle image velocimetry (micro-PIV). A stent strut may cause recirculation areas, which are considered to be the source of thrombosis and the process of in-stent restenosis. The simulations showed that a reduced strut height and a chamfering of the struts reduce these recirculation zones. The numerically determined results were compared with experimental investigations. For this purpose metallic stent structures were transferred into transparent channel systems made of PDMS. The experimental investigations confirm the results of numerical simulations.

Sign in / Sign up

Export Citation Format

Share Document