The Impact of the Wind Power Plant on the Air Radars Functioning

2018 ◽  
Author(s):  
Victorita Radulescu
Keyword(s):  
Power Plant ◽  
Wind Power ◽  
Wind Turbines ◽  
Power Plants ◽  
Wind Farms ◽  
Radar System ◽  
Wind Power Plant ◽  
Surveillance Systems ◽  
Proper Functioning ◽  
The Impact

Nowadays a large interest in the public and private sector is dedicated in generating electricity using renewable resources. Thus, over 60,000 MW is produced worldwide by using the wind energy. These systems are generally composed of power plants formed from 2–3 to several tens, hundreds of wind turbines with rotating blades that reach heights over 160m. The number, the height, and the rotation of these wind turbines represent technical challenges for the radar system efficiency and accuracy. They should be assessed carefully, in each case, to ensure that it maintains an acceptable level of the air space surveillance capability. The research paper presents the influence of the wind power farms on the air radars especially in cases of surveillance area, both for the primary radars and the secondary radars. There are differences between the interference between the wind turbines and radars functioning, depending on the types of radars. In the last decades in Romania is a permanent effort to increase the number the wind farms built, or in the process of being built, but also referring at the number of wind turbines in these parks and their physical dimensions. This paper focuses on the effects of the wind farms on the radars efficiency, and their potential impact on the ability of airspace surveillance. This results in a concise and transparent reference guide for developers of wind farms when assessing the impact of wind turbines on aerial surveillance systems. Specialists are relatively unanimous in their opinion that, in order to make an assessment of the impact of the wind farms on the radars must be defined at least three areas corresponding to different levels of the technical expertise. They must be combined with the influence of the wind farms on the ability of the radar to fulfill the mission, why they were installed, assuming that it is necessary to create an exclusive protection area. First, are discussed briefly the principles of the radar’s operation, depending on their type: primary and secondary surveillance radars. Further, are estimated the induced reflections by the wind power plant on the radar system. If the number of false targets generated by the reflections from wind turbines is too big, so it exceeds the processing capacity of the radar, the operational capacity will suffer. There are presented some theoretical aspects, followed by some cases where the proper functioning of the primary and secondary radars is affected. The model is tested in field, at two different distances, with airplanes and helicopter flying at different altitudes, with radar placed near the wind power plant Fantanele – Cogelac, the biggest in Romania. Finally, is estimated the area necessary to assure proper functioning of radars. Some conclusions and references are presented.

Application of Reference Designation for Power Plants to Wind Turbines

2014 ◽  
Vol 529 ◽  
pp. 476-480
Author(s):  
Li Yi ◽  
San Yong Liu ◽  
Qiang Qiang Yu
Keyword(s):  
Power Plant ◽  
Wind Power ◽  
Wind Turbines ◽  
Power Plants ◽  
Economic Effect ◽  
Technical Committee ◽  
International Standards ◽  
Identification System ◽  
Wind Power Plant

RDS-PP (Reference Designation for Power Plants) is a new identification system for power plants, which basis and structure are based on international standards. With the purposes to meet the designation of new power plants like wind power plant, KKS (Kraftwerk-Kennzeichen system) is developed to RDS-PP. VGB technical committee recommends newly-built power plants adopts RDS-PP directly. Though leading to additional work, adopting new identification system have a long term economic effect.

scholarly journals Control the System and Environment of Post-Production Wind Turbine Blade Waste Using Life Cycle Models. Part 1. Environmental Transformation Models

Polymers ◽  
2020 ◽  
Vol 12 (8) ◽  
pp. 1828 ◽  
Author(s):  
Izabela Piasecka ◽  
Patrycja Bałdowska-Witos ◽  
Józef Flizikowski ◽  
Katarzyna Piotrowska ◽  
Andrzej Tomporowski
Keyword(s):  
Life Cycle ◽  
Power Plant ◽  
Wind Power ◽  
Power Plants ◽  
Negative Impact ◽  
Polymer Materials ◽  
Wind Power Plant ◽  
Polymer Waste ◽  
Wind Power Plants ◽  
The Impact

Controlling the system—the environment of power plants is called such a transformation—their material, energy and information inputs in time, which will ensure that the purpose of the operation of this system or the state of the environment, is achieved. The transformations of systems and environmental inputs and their goals describe the different models, e.g., LCA model groups and methods. When converting wind kinetic energy into electricity, wind power plants emit literally no harmful substances into the environment. However, the production and postuse management stages of their components require large amounts of energy and materials. The biggest controlling problem during postuse management is wind power plant blades, followed by waste generated during their production. Therefore, this publication is aimed at carrying out an ecological, technical and energetical transformation analysis of selected postproduction waste of wind power plant blades based on the LCA models and methods. The research object of control was eight different types of postproduction waste (fiberglass mat, roving fabric, resin discs, distribution hoses, spiral hoses with resin, vacuum bag film, infusion materials residues, surplus mater), mainly made of polymer materials, making it difficult for postuse management and dangerous for the environment. Three groups of models and methods were used: Eco-indicator 99, IPCC and CED. The impact of analysis objects on human health, ecosystem quality and resources was controlled and assessed. Of all the tested waste, the life cycle of resin discs made of epoxy resin was characterized by the highest level of harmful technology impact on the environment and the highest energy consumption. Postuse control and management in the form of recycling would reduce the negative impact on the environment of the tested waste (in the perspective of their entire life cycle). Based on the results obtained, guidelines and models for the proecological postuse control of postproduction polymer waste of wind power plants blades were proposed.

scholarly journals Ground vibrations caused by wind power plant work as environmental pollution - case study

2019 ◽  
Vol 302 ◽  
pp. 01002
Author(s):  
Sylwester Borowski
Keyword(s):  
Power Plant ◽  
Environmental Pollution ◽  
Wind Power ◽  
Wind Farms ◽  
Wind Power Plant ◽  
Ground Vibrations ◽  
Living Organisms ◽  
The Impact

The paper presents issues related to the impact of wind farms on the environment. Emphasis was placed on vibrations that are transferred to the ground through the foundations. As research has shown - a case study - vibrations are felt up to about 1000 m from wind farms. According to other literature sources, this may affect living organisms in the ground.

scholarly journals Life Cycle Analysis of Ecological Impacts of an Offshore and a Land-Based Wind Power Plant

2019 ◽  
Vol 9 (2) ◽  
pp. 231 ◽  
Author(s):  
Izabela Piasecka ◽  
Andrzej Tomporowski ◽  
Józef Flizikowski ◽  
Weronika Kruszelnicka ◽  
Robert Kasner ◽  
...  
Keyword(s):  
Life Cycle ◽  
Power Plant ◽  
Wind Power ◽  
Power Plants ◽  
Ecological Impacts ◽  
Offshore Wind ◽  
Wind Power Plant ◽  
Offshore Wind Power ◽  
Wind Power Plants ◽  
The Impact

This study deals with the problems connected with the benefits and costs of an offshore wind power plant in terms of ecology. Development prospects of offshore and land-based wind energy production are described. Selected aspects involved in the design, construction, and operation of offshore wind power plant construction and operation are presented. The aim of this study was to analyze and compare the environmental impact of offshore and land-based wind power plants. Life cycle assessment analysis of 2-MW offshore and land wind power plants was made with the use of Eco-indicator 99 modeling. The results were compared in four areas of impact in order to obtain values of indexes for nonergonomic (impact on/by operator), nonfunctional (of/on the product), nonecological (on/by living objects), and nonsozological impacts (on/by manmade objects), reflecting the extent of threat to human health, the environment, and natural resources. The processes involved in extraction of fossil fuels were found to produce harmful emissions which in turn lead to respiratory system diseases being, thus, extremely dangerous for the natural environment. For all the studied areas, the impact on the environment was found to be higher for land-based wind power plants than for an offshore wind farm.

scholarly journals Investigation and prediction of noise pollution levels from wind turbines: A case study of Nexif Energy Ben Tre wind power plant, South Vietnam

2021 ◽  
Author(s):  
Huan Nguyen Quoc ◽  
Cuong Tran Thien ◽  
Cu Nguyen Xuan ◽  
Tuan Vu Dinh ◽  
Minh Tran ◽  
...  
Keyword(s):  
Power Plant ◽  
Wind Power ◽  
Wind Turbines ◽  
Background Noise ◽  
Wind Farms ◽  
Wind Power Plant ◽  
Noise Levels ◽  
Night Time ◽  
Project Site ◽  
Ifc Standard

In recent years, the demand for electric power in Vietnam has increased at annual growth rates of 10% to 12%, and the challenge is to promote renewable energy sector. One of these sustainable energy sources is to harness energy from the wind through wind turbines (WTs). In fact, more wind power plants in Vietnam are continuously to be built due to the rapidly growing demand of country's industrialization and modernization process. However, a significant hindrance preventing the widespread use of WTs in Vietnam is the noise they produce, which significantly contributes to the annoyance experienced by residents living near wind farms. The prediction of noise impacts for new wind farms is one of the many aspects of the environmental impact assessment process in Vietnam as well as in the world. In addition, the determination of the 45 dBA noise contour-line is very important because it is the basis for determining the scope of the project impact according to the IFC/WB performance standards and the number of households to be relocated from the project site. The article’s main focus is therefore on the estimation and simulation of the acoustical noise produced by 18 WTs during the operation phase of Nexif Energy Ben Tre wind power plant and the background noise levels at the project site have been performed by using a combination of specific study methods such as environmental modeling (iNoise Pro modeling software), mapping and geographic information systems. The obtained results show the importance of using modeling method in quantifying the noise levels generated from 18 wind turbines of the Nexif Energy Ben Tre wind power plant met IFC standard and Vietnamese regulation on noise during day-time, but did not meet IFC standard on noise during night-time. The level of background noise measured during night-time in the project area also did not meet IFC standard. Therefore, the overall cumulative noise level exceeds the IFC standard for residential area (45 dBA only). In addition, the appropriate solutions to reduce noise levels from WTs are also proposed.

scholarly journals Research of Emergency Modes of Wind Power Plants Using Computer Simulation

Energies ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4780
Author(s):  
Mohamed Zaidan Qawaqzeh ◽  
Oleksandr Miroshnyk ◽  
Taras Shchur ◽  
Robert Kasner ◽  
Adam Idzikowski ◽  
...  
Keyword(s):  
Power Plant ◽  
Wind Power ◽  
Wind Turbines ◽  
Power Plants ◽  
Voltage Drop ◽  
Total Power ◽  
Wind Power Plant ◽  
Wind Power Plants ◽  
Short Circuits ◽  
Regulation Mode

The aim of this study is to investigate changes in the wind power plant energy production parameters under the conditions of sudden wind changes and voltage drop. To achieve these goals, a simulation of operation of wind power plants was performed. Twelve wind turbines with variable rotational speed equipped with a Fuhrländer FL 2500/104 asynchronous double-fed induction generator (DFIG) were used, each with an installed capacity of 2.5 MW. A general scheme of a wind power plant has been developed using a modular-trunk power distribution scheme. The system consists of wind power modules and a central substation, which allows total power to be supplied to the power system at a voltage of 35 kV. The central substation uses two high voltage switchgears. Four modules were used, each of them consisting of three wind turbines, with a power of 7.5 MW. The simulation of the wind turbines was performed in the MATLAB® Simulink® software environment. The mode of response of the turbines to a change in wind speed, a voltage drop in the 35 kV voltage system, and a one-phase short circuit to the ground in the system of 10.5 kV voltage was explored. The results show that a sudden voltage drop and the appearance of short circuits influence the wind power plant (WPP) operation in a different way independent of regulation mode. The power generation from WPP will be limited when voltage drop occurred for both AC and Voltage regulation mode and during short circuits while WPP is set on AC regulation mode.

scholarly journals Comparison Analysis of Blade Life Cycles of Land-Based and Offshore Wind Power Plants

2018 ◽  
Vol 25 (s1) ◽  
pp. 225-233 ◽  
Author(s):  
Andrzej Tomporowski ◽  
Izabela Piasecka ◽  
Józef Flizikowski ◽  
Robert Kasner ◽  
Weronika Kruszelnicka ◽  
...  
Keyword(s):  
Power Plant ◽  
Wind Power ◽  
Power Plants ◽  
Life Cycles ◽  
Offshore Wind ◽  
Wind Power Plant ◽  
Comparison Analysis ◽  
Offshore Wind Power ◽  
Wind Power Plants ◽  
The Impact

Abstract In recent years, the offshore wind power industry has been growing dynamically. A key element which decides upon power output of a wind power plant is blades. They are most frequently produced from polymers – laminates with epoxy resins and fiberglass. In the near future, when the blade life cycles are over, large amounts of waste material of this type will have to be reused. This paper presents a comparison analysis of the impact of particular material existence cycle stages of land-based and offshore wind power plant blades on the environment. Two wind power plant blades, of about 49 m in length each, were examined using the LCA method, the programme SimaPro, and Ekowskaźnik 99 modelling (phase LCIA).

scholarly journals Comparative analysis of the impact of objects of traditional and alternative energy on the environment

2021 ◽  
pp. 58-63
Author(s):  
Yuliya S. Borisova ◽  
Nataliya S. Samarskaya
Keyword(s):  
Comparative Analysis ◽  
Power Plant ◽  
Wind Power ◽  
Alternative Energy ◽  
Power Plants ◽  
Negative Impact ◽  
Thermal Power ◽  
Energy Sources ◽  
Wind Power Plant ◽  
The Impact

Introduction. Active withdrawal of energy raw materials from the subsoil, as well as technogenic impact from energy sources based on traditional fuel, lead to irreversible environmental consequences. To minimize this impact, it is necessary to start from two main conditions: the search for alternative energy sources and the improvement of the existing ones. Problem Statement. The objective of this study is a comparative analysis of energy facilities in order to identify the plant that has the greatest negative impact on the environment. Theoretical part. The comparative analysis of various energy production systems reflects the ecological and economic components of each. For example, a thermal power plant (TPP), a nuclear power plant (NPP) and a wind power plant (WPP) are considered. The negative impact on the environment is mainly exerted on the atmospheric air, in connection with which the data on the amount of pollutants are considered. Also, a modified Leopold matrix was constructed for an expert assessment of the mentioned stations. Conclusions. The results of the analysis show that among the considered power plants, the wind power plant is the most environmentally friendly and favorable for the health of the population.

scholarly journals Impact of the Wind Turbine on the Parameters of the Electricity Supply to an Agricultural Farm

2021 ◽  
Vol 13 (13) ◽  
pp. 7279
Author(s):  
Zbigniew Skibko ◽  
Magdalena Tymińska ◽  
Wacław Romaniuk ◽  
Andrzej Borusiewicz
Keyword(s):  
Power Plant ◽  
Wind Turbine ◽  
Wind Power ◽  
Rural Areas ◽  
Power Plants ◽  
Reactive Power ◽  
Supply Voltage ◽  
Common Source ◽  
Voltage Fluctuations ◽  
The Impact

Wind power plants are an increasingly common source of electricity located in rural areas. As a result of the high variability of wind power, and thus the generated power, these sources should be classified as unstable sources. In this paper, the authors attempted to determine the impact of wind turbine operation on the parameters of electricity supplied to farms located near the source. As a result of the conducted field tests, variability courses of the basic parameters describing the supply voltage were obtained. The influence of power plant variability on the values of voltage, frequency, and voltage distortion factor was determined. To estimate the capacity of the transmission lines, the reactive power produced in the power plant and its effect on the value of the power factor were determined. The conducted research and analysis showed that the wind power plant significantly influences voltage fluctuations in its immediate vicinity (the maximum value registered was close to 2%, while the value required by law was 2.5%). Although all the recorded values are within limits specified by the current regulations (e.g., the THD value is four times lower than the required value), wind turbines may cause incorrect operation of loads connected nearby. This applies mainly to cases where consumers sensitive to voltage fluctuations are installed in the direct vicinity of the power plant.

scholarly journals Optimization of a Small Wind Power Plant for Annual Wind Speed Distribution

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1587
Author(s):  
Krzysztof Wrobel ◽  
Krzysztof Tomczewski ◽  
Artur Sliwinski ◽  
Andrzej Tomczewski
Keyword(s):  
Wind Speed ◽  
Power Plant ◽  
Wind Power ◽  
Power Plants ◽  
Control Method ◽  
Wind Power Plant ◽  
Switched Reluctance ◽  
Wind Speeds ◽  
Wind Speed Distribution ◽  
And Control

This article presents a method to adjust the elements of a small wind power plant to the wind speed characterized by the highest annual level of energy. Tests were carried out on the basis of annual wind distributions at three locations. The standard range of wind speeds was reduced to that resulting from the annual wind speed distributions in these locations. The construction of the generators and the method of their excitation were adapted to the characteristics of the turbines. The results obtained for the designed power plants were compared with those obtained for a power plant with a commercial turbine adapted to a wind speed of 10 mps. The generator structure and control method were optimized using a genetic algorithm in the MATLAB program (Mathworks, Natick, MA, USA); magnetostatic calculations were carried out using the FEMM program; the simulations were conducted using a proprietary simulation program. The simulation results were verified by measurement for a switched reluctance machine of the same voltage, power, and design. Finally, the yields of the designed generators in various locations were determined.

Sign in / Sign up

Export Citation Format

Share Document