Numerical Simulation on Forced Convection Heat Transfer Performance and Pressure Drop of High Permeability Porous Media

2016 ◽  
Author(s):  
Shigeki Hirasawa ◽  
Tsuyoshi Kawanami ◽  
Katsuaki Shirai
Keyword(s):  
Heat Transfer ◽  
Porous Media ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Air Flow ◽  
Convection Heat Transfer ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Convection Heat

We studied the forced convection heat transfer performance and pressure drop of high permeability metal cellular porous media in air flow using a 3-dimensional thermofluid computation code. The temperature and velocity distributions in the air flow region, local heat transfer coefficient, and local heat flux on the surface of the porous media were numerically calculated for steady air flow by changing the parameters of the pore size and air velocity. The cellular porous media were modeled by pin array, cube geometry, and truncated octahedron geometry using thin wires. The diameter of the wires was 0.1 mm, and the pore per inch (PPI) was 5–50. The relations between the Nusselt number using the volumetric heat transfer coefficient and the Reynolds number were obtained from our calculation results, and we compared them with conventionally proposed experimental correlations. Also, the pressure drop calculation result was compared with conventionally proposed experimental correlations. The following results were obtained. The local heat transfer coefficient and local heat flux on the surface of porous media were small near the joint positions of the wires of the cellular porous media because of the thermal boundary layer. The volumetric heat transfer coefficient and pressure drop agreed with conventionally proposed experimental correlations within errors of twice the volumetric heat transfer coefficient and pressure drop. The relation between the heat transfer rate per unit volume and the heat transfer area per unit volume agreed with the convection heat transfer correlation for a tube bundle.

Experimental Study on Flow Boiling of HFC134a in a Multi-Port Extruded Tube

2004 ◽  
Author(s):  
Ken Kuwahara ◽  
Shigeru Koyama ◽  
Kengo Kazari
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Flow Boiling ◽  
Rectangular Channel ◽  
Large Diameter ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Inlet Temperature

In the present study, the local heat transfer and pressure drop characteristics are investigated experimentally for the flow boiling of refrigerant HFC134a in a multi-port extruded tube of 1.06mm in hydraulic diameter. The test tube is 865mm in total length made of aluminum. The pressure drop is measured at an interval of 191 mm, and the local heat transfer coefficient is measured in every subsection of 75mm in effective heating length. Experimental ranges are as follows: the mass velocity of G = 100–700 kg/m2s, the inlet temperature of Tin = 5.9–11.4 °C and inlet pressure of about 0.5 MPa. The data of pressure drop are compared with a few previous correlations for small diameter tubes, and the correlations can predict the data relatively good agreement. The data of heat transfer coefficient is compared with the correlations of Yu et al. proposed for relatively large diameter tubes. It is found that there are some differences about two phase multiplier factor of convective heat transfer between the circular channel and rectangular channel.

Overall Thermal Performance of a Rectangular Channel With an Array of Elongated Pedestals

2013 ◽  
Author(s):  
S. Huang ◽  
Y. Y. Yan ◽  
J. D. Maltson ◽  
E. Utriainen
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Thermal Performance ◽  
Rectangular Channel ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Flow Area ◽  
Coefficient Distribution

Experiments have been conducted to investigate the overall thermal performance of a rectangular channel implemented with an elongated pedestal array. The staggered pedestals were elongated in the spanwise direction in order that the jet flow from between the pedestals impinges at the centre of the pedestals in the downstream row. The average heat transfer coefficient of the pedestal and the local heat transfer coefficient distribution of the bottom channel wall were investigated for different geometrical arrangements. The pressure drop across the pedestal bank was measured. The transient liquid crystal method was used to obtain the local heat transfer coefficient distribution on the bottom channel wall and the lumped capacitance method was used to measure the average heat transfer coefficient of the pedestals in the last two rows of the bank. Five pressure taps were arranged on the centerline of each gap between two pedestal rows to measure the pressure drop. The heat transfer coefficients were measured over the Reynolds number range from 10,000 to 30,000. The minimum flow area to the channel cross-section flow area ratio ranged from 0.149 to 0.333. The effects of pedestal geometry and array distribution were investigated in detail showing the relationship between the pedestal array geometry, heat transfer enhancement and pressure drop. Conclusions were drawn on the effects of geometry and flow conditions on overall thermal performance of the respective channels.

A Comparison Between the Local Free Convection Heat Transfer Coefficients of Horizontal Cylinders in Vertical and Inclined Arrays

2006 ◽  
Author(s):  
Mehdi Ashjaee ◽  
Tooraj Yousefi
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Rayleigh Number ◽  
Free Convection ◽  
Convection Heat Transfer ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Horizontal Cylinder ◽  
Convection Heat ◽  
Free Convection Heat

Laminar free convection heat transfer from vertical and inclined arrays of horizontal isothermal cylinders in air was investigated experimentally and numerically. Experiments were carried out using Mach-Zehnder interferometer and the FLUENT code was used for numerical study. Investigation was performed for vertical and horizontal cylinder spacing from 2 to 5 and to 2 cylinder diameter respectively. The Rayleigh number based on the cylinder diameter varied between 103 and 3×103. The effect of vertical and horizontal cylinder spacing and Rayleigh number on the local heat transfer from each individual cylinder was investigated. It was seen that the local heat transfer coefficient of each cylinder strongly depends on its position relative to the others. This variation of the local heat transfer coefficient was explained by the interaction of plume’s temperature and velocity profiles.

Investigation of Heat Transfer Characteristics of Supercritical Carbon Dioxide at Microchannels

2019 ◽  
Author(s):  
Mostafa Asadzadeh ◽  
Anatoly Parahovnik ◽  
Stephen Adeoye ◽  
Yoav Peles
Keyword(s):  
Heat Transfer ◽  
Carbon Dioxide ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Supercritical Co2 ◽  
Local Heat Transfer ◽  
Local Heat ◽  
System Pressure ◽  
Micro Channels

Abstract Carbon Dioxide (SCO2) can revolutionize the thermal management landscape due to a dramatic increase in enthalpy and a specific heat near supercritical state, particularly along the pseudocritical line, which correspond to much lower temperatures and pressures than water and other refrigerants. This study is conducted to assess the capability of supercritical CO2 in heat transfer applications. The heat transfer coefficient of carbon dioxide near the pseudocritical conditions was experimentally studied at the micro scale. Devices with 20 micro channels were fabricated to measure local and average heat transfer coefficient as well as system pressure drop. The experimental results showed a significant increase up to 72000 W/m2.k in local heat transfer coefficient and large pressure drop up to 3 MPa at microscale with supercritical CO2.

scholarly journals Effect of perforated concave delta winglet vortex generators on heat transfer augmentation of fluid flow inside a rectangular channel: An experimental study

2018 ◽  
Vol 204 ◽  
pp. 04015
Author(s):  
Syaiful ◽  
MSK Tony SU ◽  
Nazaruddin Sinaga ◽  
Retno Wulandari ◽  
Myung-whan Bae
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Convection Heat Transfer ◽  
Vortex Generator ◽  
Longitudinal Vortex ◽  
Convection Heat ◽  
Convection Heat Transfer Coefficient ◽  
Delta Winglet

Compact heat exchanger with gas as a heat exchange medium is widely used in power plants, automotive, air conditioning, and others. However, the gas has a low thermal conductivity resulting in high thermal resistance causing a low rate of heat transfer. Therefore an improvement to the convection heat transfer coefficient is necessary. One way to enhance the convection heat transfer coefficient is to use a longitudinal vortex generator. However, the increase in convection heat transfer coefficient is followed by an increase in pressure drop. Therefore, this work aims to improve the convection heat transfer coefficient with a low pressure drop. To achieve this goal, experiments were carried out by perforating a longitudinal vortex generator with a diameter of 5 mm with variations in holes number one, two and three. Two types of longitudinal vortex generators are compared. The experimental results show that the convection heat transfer coefficient for the case of perforated concave delta winglet vortex generator is only decreased by 1% from that without a hole, while the pressure drop is decreased by 11.6%.

Forced Convection Heat Transfer From a Uniformly Heated Sphere

1962 ◽  
Vol 84 (2) ◽  
pp. 133-140 ◽  
Author(s):  
W. S. Brown ◽  
C. C. Pitts ◽  
G. Leppert
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Convection Heat Transfer ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Sphere Diameter ◽  
Transfer Coefficients ◽  
Number Range ◽  
Average Heat

An approximate analytical solution is presented for the variation of the local heat-transfer coefficient over the forward half of a uniformly heated sphere. Experimental measurements with water over a Reynolds number range of 5000 to 480,000 and a Prandtl number range of 2.2 to 6.8 give local coefficients which are in good agreement with analytical results. Average heat-transfer coefficients for the uniformly heated sphere are slightly higher than similar results reported earlier [1] for an isothermal sphere. The effect of variations of heat flux on the average heat-transfer coefficient is correlated in a manner similar to that which was used for the isothermal data. Three different duct sizes were used in the experiment to determine the effect of this variable, and the correlations which are presented are based on duct-to-sphere diameter ratios of 2, 2.67, and 4.

Supercritical Heat Transfer and Pressure Drop in Refrigerant R410A

2003 ◽  
Author(s):  
Biswajit Mitra ◽  
Srinivas Garimella
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Cooling Water ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Coolant Temperature ◽  
Transfer Coefficients ◽  
Water Stream

This paper presents the results of an experimental study on heat transfer and pressure drop at critical and supercritical pressures of refrigerant R410A inside a horizontal 9.4 mm I.D. tube. Knowledge of heat transfer and pressure drop in such refrigerants blends at elevated pressures is gaining increasing attention for the design of vapor-compression space-conditioning and water heating systems at high heat rejection temperatures. Local heat transfer coefficients and pressure drops were measured for the mass flux range 200 < G < 800 kg/m2-s for the temperature range from 30–110°C. A technique that simultaneously allows accurate measurement of low local heat duties and deduction of the tube-side heat transfer coefficient from the measured overall resistance was used. A primary cooling loop using water at high flow rates ensures that the refrigerant side presents the governing thermal resistance. Heat exchange with a secondary cooling water stream at a much lower flow rate amplifies the coolant temperature difference, which in turn enables accurate heat duty measurements. The results show that the heat transfer coefficient exhibits a sharp peak in the vicinity of the vapor-liquid dome. These data are compared with the most relevant correlations from the literature and possible explanations for agreement and discrepancies between the data and predictions are provided.

Sign in / Sign up

Export Citation Format

Share Document