High Strain Rate Compressive Properties of Soft Tissue

2003 ◽  
Author(s):  
Caleb R. Van Sligtenhorst ◽  
Duane S. Cronin ◽  
G. Wayne Brodland
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Material Properties ◽  
Fiber Orientation ◽  
Soft Tissues ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Strain Rates ◽  
Post Mortem ◽  
Fresh Tissue

High strain rate material properties and constitutive equations are essential for the development of numerical and physical models to assess the performance of soft materials subject to high rate deformation, with potential applications including protective equipment and vehicle crashworthiness. However, these properties are not available for many soft tissues. This is because specialized testing methods must be employed to obtain the necessary data. Fresh bovine tissue from the semimembranosis muscle was obtained and tested using a polymeric Split Hopkinson Pressure Bar. Samples were tested from 1.4 to 200 hours post mortem to observe the effect of rigor and other possible temporal effects on the material properties. Since this muscle had relatively uniform fiber orientation, it was possible to obtain specimens with fiber directions parallel, perpendicular, and at 45 degrees to the compression axis. The stress-strain curves for the muscle were concave upwards, as is typical of soft tissues at high strain rates. Fiber orientation was determined to have negligible effect at the tested strain rates. The testing revealed that the stiffness of the tissue increased with post mortem time until approximately 6 hours. At times greater than 200 hours post mortem, the tissue properties were found to be very similar to the properties of fresh tissue. These findings suggest that properties of fresh tissue might be estimated using more easily obtained post-rigor tissue.

scholarly journals Effect of Stress-Relieving Heat Treatment on the High Strain Rate Dynamic Compressive Properties of Additively Manufactured Ti6Al4V (ELI)

Metals ◽  
2020 ◽  
Vol 10 (5) ◽  
pp. 653
Author(s):  
Amos Muiruri ◽  
Maina Maringa ◽  
Willie du Preez ◽  
Leonard Masu
Keyword(s):  
Plastic Strain ◽  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Deformation Behaviour ◽  
Test System ◽  
Strain Rates ◽  
Stress Relieving ◽  
Strain Rate Compression

A study was undertaken on the compressive high strain rate properties and deformation behaviour of Direct Metal Laser-Sintered (DMLS) Ti6Al4V (ELI) parts in two separate forms: as-built (AB) and stress relieved (SR). The high strain rate compression tests were carried out using a Split Hopkinson Pressure Bar test system at ambient temperature. The average plastic strain rates attained by the system were 400 s−1 and 700 s−1. Comparative analyses of the performance (flow stresses and fracture strains) of AB and SR specimens were carried out based on the results obtained at these two plastic strain rates. Microstructural analyses were performed to study the failure mechanisms of the deformed specimens and fracture surfaces. Vickers microhardness test values were obtained before and after high strain rate compression testing. The results obtained in both cases showed the strain rate sensitivity of the stress-relieved samples to be higher in comparison to those of as-built ones, at the same value of true strain.

High Strain Rate Compressive Behavior of Micro-Fibre Reinforced Fine Grained Cementitious Composite

2018 ◽  
Vol 276 ◽  
pp. 140-147
Author(s):  
Martina Drdlová ◽  
Miloslav Popovič ◽  
René Čechmánek
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Compressive Strain ◽  
Fibre Reinforcement ◽  
Strain Rates ◽  
Cementitious Composite ◽  
Compressive Behavior ◽  
Hopkinson Pressure Bar

This paper presents an experimental study on the high strain rate compressive behavior of micro-fibre reinforced ultrahigh performance cementitious composite, which is intended to be used as a matrix for slurry infiltrated fibre concrete (SIFCON). Cementitious composite specimens with 5 different types of microfibres, namely aramid, carbon, wollastonite, polypropylene and glass in amounts of 1.5-2.0% by volume were prepared and investigated. Split Hopkinson pressure bar (SHPB) equipment was used to determine the cementitious composite behavior at strain rates up to 1600 s-1. Quasistatic tests were performed, as well and ratios of these properties at high strain rates to their counterparts at static loading were compared. The dynamic increase factors were calculated. Strain rate sensitivity was observed - compressive strength was found to be increased with strain rate for all tested specimens. Peak stress values, critical compressive strain and post peak behaviour varies for specimens with different micro-fibre reinforcement, which allows to find the optimal reinforcement for high strain rate impacted structures.

Compressive Behavior of Plain and Fiber-Reinforced High-Strength Concrete Subjected to High Strain Rate Loading

2011 ◽  
Vol 82 ◽  
pp. 57-62 ◽  
Author(s):  
Sha Sha Wang ◽  
Min Hong Zhang ◽  
Ser Tong Quek
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strength Concrete ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
High Strength ◽  
Strain Rates ◽  
Compressive Behavior ◽  
High Strain Rates ◽  
Strength Concrete

This paper presents a laboratory experimental study on the effect of high strain rate on compressive behavior of plain and fiber-reinforce high-strength concrete (FRHSC) with similar strength of 80-90 MPa. Steel fibers, polyethylene fibers, and a combination of these were used in the FRHSC. A split Hopkinson pressure bar equipment was used to determine the concrete behavior at strain rates from about 30 to 300 s-1. The ratio of the strength at high strain rates to that at static loading condition, namely dynamic increase factor (DIF), of the concretes was determined and compared with that recommended by CEB-FIP code. Fracture patterns of the specimens at high strain rates are described and discussed as well. Results indicate that the CEB-FIP equation is applicable to the plain high strength concrete, but overestimates the DIF of the FRHSC at strain rates beyond a transition strain rate of 30 s-1. Based on the experimental results, a modified equation on DIF is proposed for the FRHSC.

Effect of Isothermal Aging and High Strain Rate on Material Properties of Innolot

2013 ◽  
Author(s):  
Pradeep Lall ◽  
Geeta Limaye ◽  
Sandeep Shantaram ◽  
Jeff Suhling
Keyword(s):  
Elevated Temperature ◽  
High Strain Rate ◽  
Strain Rate ◽  
Material Properties ◽  
Isothermal Aging ◽  
High Strain ◽  
Image Correlation ◽  
Lead Free ◽  
Strain Rates ◽  
Full Field

Industry migration to lead-free solders has resulted in a proliferation of a wide variety of solder alloy compositions. The most popular amongst these are the Tin-Silver-Copper (Sn-Ag-Cu or SAC) family of alloys like SAC105, SAC305 etc. Recent studies have highlighted the detrimental effects of isothermal aging on the material properties of these alloys. SAC alloys have shown up to 50% reduction in their initial elastic modulus and ultimate tensile strength within a few months of elevated temperature aging. This phenomenon has posed a severe design challenge across the industry and remains a road-block in the migration to Pb-free. Multiple compositions with additives to SAC have been proposed to minimize the effect of aging and creep while maintaining the melting temperatures, strength and cost at par with SAC. Innolot is a newly developed high-temperature, high-performance lead-free substitute by InnoRel™ targeting the automotive electronics segment. Innolot contains Nickel (Ni), Antimony (Sb) and Bismuth (Bi) in small proportions in addition to Sn, Ag and Cu. The alloy has demonstrated enhanced reliability under thermal cycling as compared to SAC alloys. In this paper, the high strain rate material properties of Innolot have been evaluated as the alloy ages at an elevated temperature of 50°C. The strain rates chosen are in the range of 1–100 per-second which are typical at second level interconnects subjected to drop-shock environments. The strain rates and elevated aging temperature have been chosen also to correspond to prior tests conducted on SAC105 and SAC305 alloys at this research center. This paper presents a comparison of material properties and their degradation in the three alloys — SAC105, SAC305 and Innolot. Full field strain measurements have been accomplished with the use of high speed imaging in conjunction with Digital Image Correlation (DIC). Ramberg-Osgood non-linear model parameters have been determined to curve-fit through the experimental data. The parameters have been implemented in Abaqus FE model to obtain full-field stresses which correlates with contours obtained experimentally by DIC.

scholarly journals HIGH STRAIN-RATE COMPRESSIVE TESTING OF FILLING MATERIALS FOR INTER-PENETRATING PHASE COMPOSITES

2019 ◽  
Vol 25 ◽  
pp. 21-24
Author(s):  
Tomáš Doktor ◽  
Tomáš Fíla ◽  
Petr Zlámal ◽  
Daniel Kytýř ◽  
Ondřej Jiroušek
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Polyurethane Foam ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Compressive Loading ◽  
Strain Rates ◽  
Filling Material ◽  
High Strain Rates ◽  
Loading Mode

In this study behavior of the selected types of filling material for the inter-penetrating phase composites was tested in compressive loading mode at low and high strain-rates. Three types of the filling material were tested, (i) ordnance gelatin, (ii) low expansion polyurethane foam, and (iii) polyurethane putty. To evaluate their impact energy absorption bulk samples of the selected materials were tested in compression loading mode at strain-rates 1000 s−1 to 4000 s−1. The high strain-rate compressive loading was provided by Split Hopkinson Pressure Bar (SHPB) which was equipped with PMMA bars to enable testing of cellular materials with low mechanical impedance. Based on the comparative measurement response to compression at both low and high strain-rates was analysed. The results show a significant strain-rate sensitivity of the ordnance gelatin and of the polyurethane putty, while strain-rate effect in the polyurethane foam was not observed.

Influence of high strain-rates on the dynamic flexural material properties of spruce–pine–fir wood studs

2014 ◽  
Vol 41 (1) ◽  
pp. 56-64 ◽  
Author(s):  
Eric Jacques ◽  
Alan Lloyd ◽  
Abass Braimah ◽  
Murat Saatcioglu ◽  
Ghasan Doudak ◽  
...  
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Material Properties ◽  
High Strain ◽  
Small Sample ◽  
Modulus Of Rupture ◽  
Strain Rates ◽  
High Strain Rates ◽  
Stress Strain ◽  
Strain Relationship

The influence of high strain-rate loading on the flexural response of typical light-frame wood construction has been investigated. A total of 30 stud grade 38 mm × 140 mm × 2440 mm (2″ × 6″ × 8′) spruce–pine–fir (S–P–F) lumber specimens were tested within a range of low and high strain-rates between 6 × 10−6 s−1 and 0.4 s−1. A single-degree-of-freedom iterative solution procedure was used to compute the high strain-rate modulus of rupture (MOR) and modulus of elasticity (MOE). The MOR was statistically enhanced by high strain-rates, while the MOE and strain at rupture were not. Since equilibrium of the dynamic stress–strain relationship requires that one or both of the MOE and strain at rupture must be sensitive to strain-rate effects, the lack of observed rate enhancement on these material properties was attributed to large scatter within a small sample set. Based on the results, material dynamic increase factors and a stress–strain relationship suitable for blast resistant design of timber structures were also proposed.

The Effect of Strain Rate on the Material Characteristics of Nickel-Based Superalloy Inconel 718

2007 ◽  
Vol 340-341 ◽  
pp. 283-288 ◽  
Author(s):  
Jung Han Song ◽  
Hoon Huh
Keyword(s):  
Dynamic Response ◽  
High Strain Rate ◽  
Strain Rate ◽  
Turbine Blade ◽  
Inconel 718 ◽  
High Speed ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Experimental Results ◽  
Stress Wave Propagation

The dynamic response of the turbine blade materials is indispensable for analysis of erosions of turbine blades as a result of impulsive loading associated with gas flow. This paper is concerned with the dynamic material properties of the Inconel 718 alloy which is widely used in the high speed turbine blade. The dynamic response at the corresponding level of the strain rate should be acquired with an adequate experimental technique and apparatus due to the inertia effect and the stress wave propagation. In this paper, the dynamic response of the Inconel 718 at the intermediate strain rate ranged from 1/s to 400/s is obtained from the high speed tensile test and that at the high strain rate above 1000/s is obtained from the split Hopkinson pressure bar test. The effects of the strain rate on the dynamic flow stress, the strain rate sensitivity and the failure elongation are evaluated with the experimental results. Experimental results from both the quasi-static and the high strain rate up to 3000/s are interpolated in order to construct the constitutive relation that should be applied to simulate the dynamic behavior of the turbine blade made of the Inconel 718.

Dynamic Deformation Behavior of As-Extruded Mg-Gd-Y Magnesium Alloy and the Microstructural Evolution

2011 ◽  
Vol 284-286 ◽  
pp. 1579-1583
Author(s):  
Ping Li Mao ◽  
Zheng Liu ◽  
Chang Yi Wang ◽  
Feng Wang
Keyword(s):  
Magnesium Alloy ◽  
Strain Rate ◽  
Deformation Behavior ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Deformation ◽  
Strain Rates ◽  
Compression Axis ◽  
Deformation Localization ◽  
Dynamic Deformation Behavior

The dynamic deformation behavior of an as-extruded Mg-Gd-Y magnesium alloy was studied by using Split Hopkinson Pressure Bar (SHPB) apparatus under high strain rates of 102 s-1 to 103s-1 in the present work, in the mean while the microstructure evolution after deformation were inspected by OM and SEM. The results demonstrated that the material is not sensitive to the strain rate and with increasing the strain rate the yield stress of as-extruded Mg-Gd-Y magnesium alloy has a tendency of increasing. The microstructure observation results shown that several deformation localization areas with the width of 10mm formed in the strain rates of 465s-1 and 2140s-1 along the compression axis respectively, and the grain boundaries within the deformation localization area are parallel with each other and are perpendicular to the compression axis. While increasing the strain rate to 3767s-1 the deformation seems become uniform and all the grains are compressed flat in somewhat. The deformation mechanism of as-extruded Mg-Gd-Y magnesium alloy under high strain rate at room temperature was also discussed.

Tension and Compression Behavior of Pre-Stressed Steel Strands at High Strain Rate

2011 ◽  
Vol 82 ◽  
pp. 154-159 ◽  
Author(s):  
Anatoly M. Bragov ◽  
Ezio Cadoni ◽  
Alexandr Yu. Konstantinov ◽  
Andrey K. Lomunov
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
High Strength ◽  
Gauge Length ◽  
Hopkinson Pressure Bar ◽  
Dog Bone ◽  
Tension And Compression ◽  
Set Up

In this paper is described the mechanical characterization at high strain rate of the high strength steel usually adopted for strands. The experimental set-up used for high strain rates testing: in tension and compression was the Split Hopkinson Pressure Bar installed in the Laboratory of Dynamic Investigation of Materials in Nizhny Novgorod. The high strain rate data in tension was obtained with dog-bone shaped specimens of 3mm in diameter and 5mm of gauge length. The specimens were screwed between incident and transmitter bars. The specimens used in compression was a cylinder of 3mm in diameter and 5mm in length. The enhancement of the mechanical properties is quite limited compared the usual reinforcing steels.

Sign in / Sign up

Export Citation Format

Share Document