Manufacturing and Mechanics-Based Characterization of Macro Fiber Composite Actuators

2002 ◽  
Author(s):  
R. Brett Williams ◽  
Brian W. Grimsley ◽  
Daniel J. Inman ◽  
W. Keats Wilkie
Keyword(s):  
Lead Zirconate Titanate ◽  
Structural Design ◽  
Fiber Composite ◽  
Cure Kinetics ◽  
Ceramic Materials ◽  
Lead Zirconate ◽  
Linear Elastic ◽  
Lamination Theory ◽  
Macro Fiber Composite

The use of piezoelectric ceramic materials for structural actuation is a fairly well developed practice that has found use in a wide variety of applications. However, just as advanced composites offer many benefits over traditional engineering materials for structural design, actuators that utilize the active properties of piezoelectric fibers can improve upon many of the limitations encountered with monolithic piezoceramic devices used to control structural dynamics. This paper discusses the Macro Fiber Composite (MFC) actuator, which utilizes piezoceramic fibers, for example, lead zirconate titanate (PZT), embedded in an epoxy matrix for structural actuation. An overview of the MFC assembly process is presented, followed by a cure kinetics model that describes the behavior of the thermosetting matrix. This empirical model is seen to agree closely with the experimental data. Lastly, a hybrid classical lamination theory is developed to predict the linear elastic properties of the MFC package as a function of the PZT fiber lamination angle.

Paste Extrusion 3D Printing and Characterization of Lead Zirconate Titanate Piezoelectric Ceramics

2021 ◽  
Author(s):  
Samuel E. Hall ◽  
Jaime E. Regis ◽  
Anabel Renteria ◽  
Luis A. Chavez ◽  
Luis Delfin ◽  
...  
Keyword(s):  
3D Printing ◽  
Lead Zirconate Titanate ◽  
Piezoelectric Ceramics ◽  
Lead Zirconate ◽  
Zirconate Titanate ◽  
Paste Extrusion

Characterization of Piezoelectric Nanofiber Composites Acoustic Emission Sensor for Structure Health Monitoring

2012 ◽  
Author(s):  
Xi Chen ◽  
Yong Shi
Keyword(s):  
Acoustic Emission ◽  
Lead Zirconate Titanate ◽  
High Sensitivity ◽  
Lead Zirconate ◽  
Steel Bar ◽  
Promising Application ◽  
Soft Polymer ◽  
Active Fiber Composites ◽  
The Mathematical Model

A nanoscale active fiber composites (NAFCs) based acoustic emission (AE) sensor with high sensitivity is developed. The lead zirconate titanate (PZT) nanofibers, with the diameter of approximately 80 nm, were electrospun on a silicon substrate. Nanofibers were parallel aligned on the substrate under a controlled electric field. The interdigitated electrodes were deposited on the PZT nanofibers and packaged by spinning a thin soft polymer layer on the top of the sensor. The hysteresis loop shows a typical ferroelectric property of as-spun PZT nanofibers. The mathematical model of the voltage generation when the elastic waves were reaching the sensor was studied. The sensor was tested by mounting on a steel surface and the measured output voltage under the periodic impact of a grounded steel bar was over 35 mV. The small size of the developed PZT NAFCs AE sensor shows a promising application in monitoring the structures by integration into composites.

Fabrication and Characterization of Sol-Gel Derived PZT/WO3 Ceramics

2008 ◽  
Vol 55-57 ◽  
pp. 369-372 ◽  
Author(s):  
T. Sreesattabud ◽  
Anucha Watcharapasorn ◽  
Sukanda Jiansirisomboon
Keyword(s):  
Lead Zirconate Titanate ◽  
Sol Gel ◽  
Rhombohedral Phase ◽  
Lead Zirconate ◽  
X Ray Diffraction ◽  
Calcination Process ◽  
Materials Used ◽  
Phase Characterization ◽  
Gel Processing

Lead zirconate titanate/tungsten oxide (PZT/WO3) ceramics were prepared from the powders synthesized by a modified triol sol-gel processing method. In this study, the starting materials used for synthesis of PZT-sol were zirconium (IV) propoxide, titanium (IV) isopropxide, lead (II) acetate trihydrate and 1,1,1,- tris (hydroxymethyl) ethane. To prepare PZT/xWO3 powders (where x = 0, 0.5, 1 and 3 wt%), nano-sized WO3 was ultrasonically dispersed and mixed with the PZT sol, dried and calcined at 600°C for 4 h. X-ray diffraction results indicated that fully crystallized powders were obtained. Phase characterization suggested that at high WO3 concentration, the reaction between PZT and WO3 occurred during the calcination process. To prepare PZT/xWO3 ceramics, the powders were pressed and sintered at 1100°C for 6 h. Phase characterization by XRD indicated that the content of WO3 significantly affected tetragonal-to-rhombohedral phase transition. Microstructure of thermally etched samples showed that increasing the content of WO3 decreased grain size of the ceramics.

Sign in / Sign up

Export Citation Format

Share Document