Particulate Emissions From Karanja Biodiesel Fuelled Turbocharged CRDI SUV Engine

2014 ◽  
Author(s):  
Jai Gopal Gupta ◽  
Avinash Kumar Agarwal ◽  
Suresh K. Aggarwal
Keyword(s):  
Particulate Matter ◽  
Power Output ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Operating Conditions ◽  
Particulate Emissions ◽  
Oxides Of Nitrogen ◽  
Biodiesel Blends ◽  
Particulate Number

The use of biodiesel substantially reduces particulate matter (PM), hydrocarbon (HC) and carbon monoxide (CO) emissions, slightly reduces power output; increases fuel consumption and marginally increases oxides of nitrogen (NOx) emission in an unmodified common rail direct injection (CRDI) diesel engine. Lower blends of biodiesel demonstrated lower emissions, while easing pressure on scarce petroleum resources, without significantly sacrificing engine power output and fuel economy. However due to adverse health effects of smaller size particulate matter (PM) emitted by internal combustion (IC) engines, most recent emission legislations restrict the PM mass emissions in addition to total particle numbers emitted. It is an overwhelming argument that usage of biodiesel leads to reduction in PM mass emissions. In this paper, experimental results of PM emissions using Karanja biodiesel blends (KB20 and KB40) in a modern CRDI transportation engine (maximum fuel injection pressure of 1600 bar) have been reported. This study also explores comparative effect of varying engine speed and load on PM emissions for biodiesel blends vis-à-vis baseline mineral diesel. Particulate size-number distribution, particle size-surface area distribution and total particulate number concentrations were experimentally determined under varying engine operating conditions and compared with baseline mineral diesel. KB20 showed highest particulate number concentration upto 80% rated engine loads, however at rated load, KB40 emitted highest number of particulates.

Particulate Emissions From Karanja Biodiesel Fueled Turbocharged CRDI Sports Utility Vehicle Engine

2015 ◽  
Vol 137 (6) ◽  
Author(s):  
Jai Gopal Gupta ◽  
Avinash Kumar Agarwal ◽  
Suresh K. Aggarwal
Keyword(s):  
Particle Size ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Particulate Emissions ◽  
Promising Alternative ◽  
Biodiesel Blends ◽  
Particulate Number ◽  
Ci Engines ◽  
Utility Vehicle

Biodiesel has emerged as one of the most promising alternative fuel to mineral diesel in last two decades globally. Lower blends of biodiesel emit fewer pollutants, while easing pressure on scarce petroleum resources, without sacrificing engine power output and fuel economy. However, diesel engines emit significant amount of particulate matter (PM), most of which are nanoparticles. Due to the adverse health impact of PM emitted by compression ignition (CI) engines; most recent emission legislations restrict the total number of particles emitted, in addition to PM mass emissions. Use of biodiesel leads to reduction in PM mass emissions; however, the particle size–numbers distribution has not been investigated thoroughly. In this paper, PM emission characteristics from Karanja biodiesel blends (KB20 and KB40) in a modern common rail direct injection (CRDI) engine used in a sports utility vehicle (SUV) with a maximum fuel injection pressure of 1600 bar have been reported. This study also explored comparative effect of varying engine speeds and loads on particulate size–number distribution, particle size–surface area distribution, and total particulate number concentration from biodiesel blends vis-à-vis baseline mineral diesel. This study showed that particulate number emissions from Karanja biodiesel blends were relatively higher than baseline mineral diesel.

Evaluation of Fuel Injection Strategies for Biodiesel-Fueled CRDI Engine Development and Particulate Studies

2018 ◽  
Vol 140 (10) ◽  
Author(s):  
Akhilendra Pratap Singh ◽  
Avinash Kumar Agarwal
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Pressure Rise ◽  
Injection Pressure ◽  
Combustion Noise ◽  
Emission Characteristics ◽  
Biodiesel Blends ◽  
Performance And Emission ◽  
Injection Parameters ◽  
Smoke Opacity

Fuel injection parameters such as fuel injection pressure (FIP) and start of main injection (SoMI) timings significantly affect the performance and emission characteristics of a common rail direct injection (CRDI) diesel engine. In this study, a state-of-the-art single cylinder research engine was used to investigate the effects of fuel injection parameters on combustion, performance, emission characteristics, and particulates and their morphology. The experiments were carried out at three FIPs (400, 700, and 1000 bar) and four SoMI timings (4 deg, 6 deg, 8 deg, and 10 deg bTDC) for biodiesel blends [B20 (20% v/v biodiesel and 80% v/v diesel) and B40 (40% v/v biodiesel and 60% v/v diesel)] compared to baseline mineral diesel. The experiments were performed at a constant engine speed (1500 rpm), without pilot injection and exhaust gas recirculation (EGR). The experimental results showed that FIP and SoMI timings affected the in-cylinder pressure and the heat release rate (HRR), significantly. At higher FIPs, the biodiesel blends resulted in slightly higher rate of pressure rise (RoPR) and combustion noise compared to baseline mineral diesel. All the test fuels showed relatively shorter combustion duration at higher FIPs and advanced SoMI timings. The biodiesel blends showed slightly higher NOx and smoke opacity compared to baseline mineral diesel. Lower particulate number concentration at higher FIPs was observed for all the test fuels. However, biodiesel blends showed emission of relatively higher number of particulates compared to baseline mineral diesel. Significantly lower trace metals in the particulates emitted from biodiesel blend fueled engine was an important finding of this study. The particulate morphology showed relatively smaller number of primary particles in particulate clusters from biodiesel exhaust, which resulted in relatively lower toxicity, rendering biodiesel to be more environmentally benign.

Effect of Fuel Injection Pressure and Engine Speed on Performance, Emissions, Combustion, and Particulate Investigations of Gasohols Fuelled Gasoline Direct Injection Engine

2019 ◽  
Vol 142 (4) ◽  
Author(s):  
Nikhil Sharma ◽  
Avinash Kumar Agarwal
Keyword(s):  
Internal Combustion Engines ◽  
Fuel Injection ◽  
Driving Forces ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Operating Conditions ◽  
Gasoline Direct Injection ◽  
Primary Alcohols ◽  
Renewable Fuel

Abstract Fuel availability, global warming, and energy security are the three main driving forces, which determine suitability and long-term implementation potential of a renewable fuel for internal combustion engines for a variety of applications. Comprehensive engine experiments were conducted in a single-cylinder gasoline direct injection (GDI) engine prototype having a compression ratio of 10.5, for gaining insights into application of mixtures of gasoline and primary alcohols. Performance, emissions, combustion, and particulate characteristics were determined at different engine speeds (1500, 2000, 2500, 3000 rpm), different fuel injection pressures (FIP: 40, 80, 120, 160 bars) and different test fuel blends namely 15% (v/v) butanol, ethanol, and methanol blended with gasoline, respectively (Bu15, E15, and M15) and baseline gasoline at a fixed (optimum) spark timing of 24 deg before top dead center (bTDC). For a majority of operating conditions, gasohols exhibited superior characteristics except minor engine performance penalty. Gasohols therefore emerged as serious candidate as a transitional renewable fuel for utilization in the existing GDI engines, without requirement of any major hardware changes.

Effects of hydrogen flow rate, injection pressure and EGR on performance of common rail direct injection (CRDi) engine in dual fuel mode

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
S.V. Khandal ◽  
T.M. Yunus Khan ◽  
Sarfaraz Kamangar ◽  
Maughal Ahmed Ali Baig ◽  
Salman Ahmed N J
Keyword(s):  
Diesel Engine ◽  
Flow Rate ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Dual Fuel ◽  
Injection Timing ◽  
Oxides Of Nitrogen ◽  
Content Type ◽  
Hydrogen Flow

PurposeThe different performance tests were conducted on diesel engine compression ignition (CI) mode and CRDi engine.Design/methodology/approachThe CI engine was suitably modified to CRDi engine with Toroidal re-entrant combustion chamber (TRCC) and was run in dual-fuel (DF) mode. Hydrogen (H2) was supplied at different flow rates during the suction stroke, and 0.22 Kg/h of hydrogen fuel flow rate (HFFR) was found to be optimum. Diesel and biodiesel were used as pilot fuels. The CRDi engine with DF mode was run at various injection pressures, and 900 bar was found to be optimum injection pressure (IP) with 10o before top dead center (bTDC) as fuel injection timing (IT).FindingsThese operating engine conditions increased formation of oxides of nitrogen (NOx), which were reduced by exhaust gas recycle (EGR). With EGR of 15%, CRDi engine resulted in 12.6% lower brake thermal efficiency (BTE), 5.5% lower hydrocarbon (HC), 7.7% lower carbon monoxide (CO), 26% lower NOx at 80% load as compared to the unmodified diesel engine (CI mode).Originality/valueThe current research is an effort to study and evaluate the performance of CRDi engine in DF mode with diesel-H2 and BCPO-H2 fuel combinations with TRCC.

Multizone Phenomenological Modeling of Combustion and Emissions for Multiple-Injection Common Rail Direct Injection Diesel Engines

2016 ◽  
Vol 138 (12) ◽  
Author(s):  
S Rajkumar ◽  
Shamit Bakshi ◽  
Pramod S Mehta
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Common Rail ◽  
Zone Model ◽  
Oxides Of Nitrogen ◽  
Multiple Injection ◽  
Start Of Injection ◽  
Wide Range

Common rail direct injection (CRDI) system is a modern variant of direct injection diesel engine featuring higher fuel injection pressure and flexible injection scheduling which involves two or more pulses. Unlike a conventional diesel engine, the CRDI engine provides simultaneous reduction of oxides of nitrogen and smoke with an injection schedule that has optimized start of injection, fuel quantity in each injection pulse, and dwell periods between them. In this paper, the development of a multizone phenomenological model used for predicting combustion and emission characteristics of multiple injection in CRDI diesel engine is presented. The multizone spray configuration with their temperature and composition histories predicted on phenomenological spray growth and mixing considerations helps accurate prediction of engine combustion and emission (nitric oxide and soot) characteristics. The model predictions of combustion and emissions for multiple injection are validated with measured values over a wide range of speed and load conditions. The multizone and the two-zone model are compared and the reasons for better comparisons for the multizone model with experimental data are also explored.

The Effect of Injection Timing, Enhanced Aftercooling, and Low-Sulfur, Low-Aromatic Diesel Fuel on Locomotive Exhaust Emissions

1992 ◽  
Vol 114 (3) ◽  
pp. 488-495 ◽  
Author(s):  
V. O. Markworth ◽  
S. G. Fritz ◽  
G. R. Cataldi
Keyword(s):  
Steady State ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Exhaust Emissions ◽  
Operating Conditions ◽  
Load Test ◽  
Injection Timing ◽  
Particulate Emissions ◽  
Oxides Of Nitrogen ◽  
Low Sulfur

An experimental study was performed to demonstrate the fuel economy and exhaust emissions implications of retarding fuel injection timing, enhancing charge air aftercooling, and using low-sulfur, low-aromatic diesel fuel for locomotive engines. Steady-state gaseous and particulate emissions data are presented from two 12-cylinder diesel locomotive engines. The two laboratory engines, an EMD 645E3B and a GE 7FDL, are each rated at 1860 kW (2500 hp) and represent the majority of the locomotive fleet in North America. Each engine was tested for total hydrocarbons (HC), carbon monoxide (CO), oxides of nitrogen (NOx), and particulate. Emissions were measured at three steady-state operating conditions: rated speed and load, idle, and an intermediate speed and load. Test results on the EMD engine indicate that a 4 deg injection timing retard, along with a low-sulfur, low-aromatic fuel and enhanced aftercooling, was effective in reducing NOx from 10.5 g/hp-h to 7.2 g/hp-h; however, particulates increased from 0.15 g/hp-h to 0.19 g/hp-h, and fuel efficiency was 4.3 percent worse. Similar observations were made with the GE engine. This paper gives details on the test engines, the measurement procedures, and the emissions results.

scholarly journals Effects of the Particulate Matter Index and Particulate Evaluation Index of the Primary Reference Fuel on Particulate Emissions from Gasoline Direct Injection Vehicles

Atmosphere ◽  
2019 ◽  
Vol 10 (3) ◽  
pp. 111 ◽  
Author(s):  
Yaowei Zhao ◽  
Xinghu Li ◽  
Shouxin Hu ◽  
Chenfei Ma
Keyword(s):  
Particulate Matter ◽  
Direct Injection ◽  
Test Procedure ◽  
Gasoline Direct Injection ◽  
Evaluation Index ◽  
Particulate Emissions ◽  
Passenger Cars ◽  
Primary Reference ◽  
Light Duty Vehicle ◽  
Particulate Number

The purpose of this experimental study was to evaluate the range of particulate mass (PM) and particulate number (PN) results from gasoline direct injection (GDI) vehicles by using four test fuels with a range of particulate matter index (PMI) from 1.38 to 2.39 and particulate evaluation index (PEI) from 0.89 to 1.92. The properties of four test fuels were analyzed with detailed hydrocarbon analysis (DHA). Two passenger cars with a GDI engine were tested with four test fuels by conducting the China 6 test procedure, which is equivalent to the worldwide harmonized light-duty vehicle test procedure (WLTP). When the fuels could meet the China 6 primary reference fuel standard with PMI from 1.38 to 2.04 and PEI from 0.89 to 1.59, the PM variation of Vehicle B was from 1.94 mg/km to 3.32 mg/km and of Vehicle A was from 2.55 mg/km to 4.15 mg/km, respectively. In addition, the PN variation of Vehicle B was from 1.57 × 1012 #/km to 3.38 × 1012 #/km and of Vehicle A was from 3.02 × 1012 #/km to 4.80 × 1012 #/km. It was noted that the two different cars had a unique response and sensitivity by using the different fuels, but PMI and PEI did trend with both the PM and the PN response. All PM and PN results from the two cars had an excellent correlation R2 > 0.94 with PMI and R2 > 0.90 with PEI. Therefore, PMI/PEI would be the appropriate specification for sooting tendency in reference fuel standards of emission regulations.

Impact of Fuel Injection Pressure on Spray and Combustion Characteristics of OME and Diesel Blends

2021 ◽  
Author(s):  
Simon LeBlanc ◽  
Xiao Yu ◽  
Gared Pisciotto ◽  
Xiaoye Han ◽  
Jimi Tjong ◽  
...  
Keyword(s):  
Diesel Fuel ◽  
Fuel Injection ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Combustion Efficiency ◽  
Particulate Emissions ◽  
Fuel Blend ◽  
Particulate Matter Emissions ◽  
Fuel Injection Pressure

Abstract Emission regulations focus on the simultaneous reduction of NOx and particulate matter emissions, especially for heavy-duty engines. Oxygenated fuels offer significant advantages in reducing particulate emissions while having little effect on NOx emissions. In addition, renewable fuels present a GHG emission advantage to meet the zero-emission requirements of future hydrocarbon fuels. Among the leading contenders, oxymethylene dimethyl ether (OME) fuels have the potential to be used for direct injection applications. OME as a blend with diesel fuel offers a direct means of improving the emissions of current on-road diesel engines without modification. In this paper, an empirical investigation into spray behavior and engine performance of diesel/OME fuel at 10% by mass has been performed under various fuel injection pressures. Neat diesel fuel was tested as a baseline case. The results are compared to tests under matching conditions using a diesel and OME fuel blend with a focus on spray characteristics, combustion behavior, and engine-out emissions. The physical properties of OME improve the volatility of diesel fuel and can tolerate shorter mixing times without promoting PM production. The PM emissions were found to be reduced by up to 50% and the combustion efficiency was improved at matching NOx levels with OME blending.

Fuel Injection Strategy for Utilization of Mineral Diesel-Methanol Blend in a Common Rail Direct Injection Engine

2020 ◽  
Vol 142 (8) ◽  
Author(s):  
Akhilendra Pratap Singh ◽  
Nikhil Sharma ◽  
Vikram Kumar ◽  
Dev Prakash Satsangi ◽  
Avinash Kumar Agarwal
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Pilot Injection ◽  
Oxides Of Nitrogen ◽  
Gas Temperature ◽  
Injection Strategy ◽  
Main Injection ◽  
Pilot Fuel ◽  
Fuel Injection Pressure

Abstract Methanol fueled internal combustion (IC) engines have attracted significant attention due to their contributions in reducing environmental pollution and fossil fuel consumption. In this study, a single-cylinder research engine was operated on MD10 (10% (v/v) methanol blended with mineral diesel) and baseline mineral diesel to explore an optimized fuel injection strategy for efficient combustion and reduced emissions. The experiments were conducted at constant engine speed (1500 rpm) and load (3 kW) using two different fuel injection strategies, namely, single pilot injection (SPI) and double pilot injection (DPI) strategy. For each pilot fuel injection strategy, the start of main injection (SoMI) timing was varied from −3 to 6° crank angle (CA) before top dead center (bTDC). To examine the effect of fuel injection pressure (FIP), experiments were performed at three different FIPs (500, 750, and 1000 bars). Results showed that the MD10 fueled engine resulted in superior combustion compared with baseline mineral diesel, which was further improved by DPI at higher FIPs. The use of DPI strategy was found to be more effective at higher FIPs, resulting in higher brake thermal efficiency (BTE), lower exhaust gas temperature (EGT), and reduced oxides of nitrogen (NOx) emissions compared with SPI strategy. Detailed investigations showed that the addition of methanol in mineral diesel reduced particulates, especially the accumulation mode particles (AMP). Different statistical analysis and qualitative correlations between fuel injection parameters showed that higher FIP and advanced SoMI timings were suitable for particulate reduction from the MD10 fueled engine.

Sign in / Sign up

Export Citation Format

Share Document