Evaluation of Fuel Injection Strategies for Biodiesel-Fueled CRDI Engine Development and Particulate Studies

2018 ◽  
Vol 140 (10) ◽  
Author(s):  
Akhilendra Pratap Singh ◽  
Avinash Kumar Agarwal
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Pressure Rise ◽  
Injection Pressure ◽  
Combustion Noise ◽  
Emission Characteristics ◽  
Biodiesel Blends ◽  
Performance And Emission ◽  
Injection Parameters ◽  
Smoke Opacity

Fuel injection parameters such as fuel injection pressure (FIP) and start of main injection (SoMI) timings significantly affect the performance and emission characteristics of a common rail direct injection (CRDI) diesel engine. In this study, a state-of-the-art single cylinder research engine was used to investigate the effects of fuel injection parameters on combustion, performance, emission characteristics, and particulates and their morphology. The experiments were carried out at three FIPs (400, 700, and 1000 bar) and four SoMI timings (4 deg, 6 deg, 8 deg, and 10 deg bTDC) for biodiesel blends [B20 (20% v/v biodiesel and 80% v/v diesel) and B40 (40% v/v biodiesel and 60% v/v diesel)] compared to baseline mineral diesel. The experiments were performed at a constant engine speed (1500 rpm), without pilot injection and exhaust gas recirculation (EGR). The experimental results showed that FIP and SoMI timings affected the in-cylinder pressure and the heat release rate (HRR), significantly. At higher FIPs, the biodiesel blends resulted in slightly higher rate of pressure rise (RoPR) and combustion noise compared to baseline mineral diesel. All the test fuels showed relatively shorter combustion duration at higher FIPs and advanced SoMI timings. The biodiesel blends showed slightly higher NOx and smoke opacity compared to baseline mineral diesel. Lower particulate number concentration at higher FIPs was observed for all the test fuels. However, biodiesel blends showed emission of relatively higher number of particulates compared to baseline mineral diesel. Significantly lower trace metals in the particulates emitted from biodiesel blend fueled engine was an important finding of this study. The particulate morphology showed relatively smaller number of primary particles in particulate clusters from biodiesel exhaust, which resulted in relatively lower toxicity, rendering biodiesel to be more environmentally benign.

Influence of Injection Pressure on Performance and Emission Characteristics of Nerium Methyl Ester Operated DI Diesel Engine

2014 ◽  
Vol 592-594 ◽  
pp. 1632-1637
Author(s):  
Ramalingam Senthil ◽  
C. Paramasivam ◽  
Rajendran Silambarasan
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Fuel Injection ◽  
Cetane Number ◽  
Load Condition ◽  
Injection Pressure ◽  
Emission Characteristics ◽  
Operational Parameters ◽  
Performance And Emission ◽  
Standard Design

Nerium methyl ester, an esterified biofuel, has an excellent cetane number and a reasonable calorific value. It closely resembles the behaviour of diesel. However, being a fuel of different origin, the standard design limits of a diesel engine is not suitable for Nerium methyl ester (NME). Therefore, in this work, a set of design and operational parameters are studied to find out the optimum performance of Nerium methyl ester run diesel engine. This work targets at finding the effects of the engine design parameter viz. fuel injection pressure (IP) on the performance with regard to specific fuel consumption (SFC), brake thermal efficiency (BTHE) and emissions of CO, CO2, HC, NOxwith N20 as fuel. Comparison of performance and emission was done for different values of injection pressure to find best possible condition for operating engine with NME. For small sized direct injection constant speed engines used for agricultural applications, the optimum injection pressure was found as 240bar.Methyl esters from Nerium, with properties close to diesel; show better performance and emission characteristics. Hence Nerium (N20) blend can be used in existing diesel engines without compromising the engine performance. Diesel (25%) thus saved will greatly help the interests of railways in meeting the demand for fuel,as diesel trains are operated at maximum load condition.

Effect of Injection Parameters and Strategy on the Noise From a Single Cylinder Direct Injection Diesel Engine

2011 ◽  
Author(s):  
Sukhbir Singh Khaira ◽  
Amandeep Singh ◽  
Marcis Jansons
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Injection Pressure ◽  
Combustion Noise ◽  
Injection Timing ◽  
Cylinder Pressure ◽  
Frequency Spectra ◽  
Single Cylinder ◽  
Direct Injection Diesel Engine ◽  
Injection Parameters

Acoustic noise emitted by a diesel engine generally exceeds that produced by its spark-ignited equivalent and may hinder the acceptance of this more efficient engine type in the passenger car market (1). This work characterizes the combustion noise from a single-cylinder direct-injection diesel engine and examines the degree to which it may be minimized by optimal choice of injection parameters. The relative contribution of motoring, combustion and resonance components to overall engine noise are determined by decomposition of in-cylinder pressure traces over a range of load, injection pressure and start of injection. The frequency spectra of microphone signals recorded external to the engine are correlated with those of in-cylinder pressure traces. Short Time Fourier Transformation (STFT) is applied to cylinder pressure traces to reveal the occurrence of motoring, combustion noise and resonance in the frequency domain over the course of the engine cycle. Loudness is found to increase with enhanced resonance, in proportion to the rate of cylinder pressure rise and under conditions of high injection pressure, load and advanced injection timing.

Effect of Injection System Parameters on Performance and Emission Characteristics of a Small Single Cylinder Diesel Engine

2021 ◽  
Vol 18 (2) ◽  
Author(s):  
D.K. Dond ◽  
N.P. Gulhane
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Direct Injection ◽  
Common Rail ◽  
Injection System ◽  
Injection Timing ◽  
Emission Characteristics ◽  
Performance And Emission ◽  
System Parameters ◽  
Main Injection

Limited fossil fuel reservoir capacity and pollution caused by them is the big problem in front of researchers. In the present paper, an attempt was made to find a solution to the same. The conventional fuel injection system was retrofitted with a simple version of the common rail direct injection system for the small diesel engine. Further, the effect of injection system parameters was observed on the performance and emission characteristics of the retrofitted common rail direct injection diesel engine. The parameters such as injection pressure, the start of pilot injection timing, the start of main injection timing and quantity of percentage fuel injection during the pilot and main injection period were considered for experimental investigation. It was observed that all the evaluated parameters were found vital for improving the engine’s performance and emission characteristics. The retrofitted common rail direct injection system shows an average 7% rise in brake thermal efficiency with economic, specific fuel consumption. At the same time, much more reduction in hydrocarbon, carbon monoxide and smoke opacity with a penalty of a slight increase in nitrogen oxides.

Particulate Emissions From Karanja Biodiesel Fueled Turbocharged CRDI Sports Utility Vehicle Engine

2015 ◽  
Vol 137 (6) ◽  
Author(s):  
Jai Gopal Gupta ◽  
Avinash Kumar Agarwal ◽  
Suresh K. Aggarwal
Keyword(s):  
Particle Size ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Particulate Emissions ◽  
Promising Alternative ◽  
Biodiesel Blends ◽  
Particulate Number ◽  
Ci Engines ◽  
Utility Vehicle

Biodiesel has emerged as one of the most promising alternative fuel to mineral diesel in last two decades globally. Lower blends of biodiesel emit fewer pollutants, while easing pressure on scarce petroleum resources, without sacrificing engine power output and fuel economy. However, diesel engines emit significant amount of particulate matter (PM), most of which are nanoparticles. Due to the adverse health impact of PM emitted by compression ignition (CI) engines; most recent emission legislations restrict the total number of particles emitted, in addition to PM mass emissions. Use of biodiesel leads to reduction in PM mass emissions; however, the particle size–numbers distribution has not been investigated thoroughly. In this paper, PM emission characteristics from Karanja biodiesel blends (KB20 and KB40) in a modern common rail direct injection (CRDI) engine used in a sports utility vehicle (SUV) with a maximum fuel injection pressure of 1600 bar have been reported. This study also explored comparative effect of varying engine speeds and loads on particulate size–number distribution, particle size–surface area distribution, and total particulate number concentration from biodiesel blends vis-à-vis baseline mineral diesel. This study showed that particulate number emissions from Karanja biodiesel blends were relatively higher than baseline mineral diesel.

Sign in / Sign up

Export Citation Format

Share Document