The Effect of Intake Valve Deactivation on Lean Stratified Charge Combustion at an Idling Condition of a Spark-Ignition Direct-Injection (SIDI) Engine

2011 ◽  
Author(s):  
Ronald O. Grover ◽  
Junseok Chang ◽  
Edward R. Masters ◽  
Paul Najt ◽  
Aditya Singh
Keyword(s):  
Laminar Flame ◽  
Direct Injection ◽  
Combustion Process ◽  
Combustion Efficiency ◽  
Combustion Stability ◽  
Charge Motion ◽  
Piston Bowl ◽  
Light Load ◽  
Spark Plug ◽  
Swirl Injector

A combined experimental and analytical study was carried out to understand the improvement in combustion performance of a 4-valve SIDI wall-guided engine operating at lean, stratified idle with enhanced in-cylinder charge motion by deactivating one of the two intake valves. A fully warmed-up engine was operated at low speed, light load by injecting the fuel from a pressure-swirl injector during the compression stroke to produce a stratified fuel cloud surrounding the spark plug at the time of ignition. Steady state flow-bench measurements and CFD calculations showed that valve deactivation primarily increased the in-cylinder swirl intensity as compared with opening both intake valves. Engine dynamometer measurements showed an increase in charge motion led to improved combustion stability, increased combustion efficiency, lower fuel consumption, and higher dilution tolerance. A CFD study was conducted using in-house models of spray and combustion to simulate the engine operating with and without valve deactivation. The computations demonstrated that the improved combustion was primarily driven by higher laminar flame speeds through enhanced mixing of internal residual gases, better containment of the fuel cloud within the piston bowl, and higher post-flame diffusion burn rates during the initial, main, and late stages of the combustion process, respectively.

The Effect of Intake Valve Deactivation on Lean Stratified Charge Combustion at an Idling Condition of a Spark Ignition Direct Injection Engine

2012 ◽  
Vol 134 (9) ◽  
Author(s):  
Ronald O. Grover ◽  
Junseok Chang ◽  
Edward R. Masters ◽  
Paul M. Najt ◽  
Aditya Singh
Keyword(s):  
Laminar Flame ◽  
Direct Injection ◽  
Combustion Process ◽  
Spark Ignition ◽  
Combustion Efficiency ◽  
Combustion Stability ◽  
Charge Motion ◽  
Piston Bowl ◽  
Light Load ◽  
Spark Plug

A combined experimental and analytical study was carried out to understand the improvement in combustion performance of a four-valve spark ignition direct injection (SIDI) wall-guided engine operating at lean, stratified idle with enhanced in-cylinder charge motion by deactivating one of the two intake valves. A fully warmed-up engine was operated at low speed, light load by injecting the fuel from a pressure-swirl injector during the compression stroke to produce a stratified fuel cloud surrounding the spark plug at the time of ignition. Steady state flow-bench measurements and computational fluid dynamics (CFD) calculations showed that valve deactivation primarily increased the in-cylinder swirl intensity as compared with opening both intake valves. Engine dynamometer measurements showed an increase in charge motion led to improved combustion stability, increased combustion efficiency, lower fuel consumption, and higher dilution tolerance. A CFD study was conducted using in-house models of spray and combustion to simulate the engine operating with and without valve deactivation. The computations demonstrated that the improved combustion was primarily driven by higher laminar flame speeds through enhanced mixing of internal residual gases, better containment of the fuel cloud within the piston bowl, and higher postflame diffusion burn rates during the initial, main, and late stages of the combustion process, respectively.

scholarly journals Effects of mixture formation strategies on combustion in dual-fuel engines – a review

2021 ◽  
Vol 184 (1) ◽  
pp. 30-40
Author(s):  
Ireneusz Pielecha ◽  
Maciej Sidorowicz
Keyword(s):  
Internal Combustion Engines ◽  
Direct Injection ◽  
Combustion Process ◽  
Critical Factor ◽  
Diesel Oil ◽  
Combustion Efficiency ◽  
Dual Fuel ◽  
Compression Ignition ◽  
Mixture Formation ◽  
Spark Plug

The article presents an overview of technical solutions for dual fuel systems used in internal combustion engines. It covers the historical and contemporary genesis of using two fuels simultaneously in the combustion process. The authors pay attention to the value of the excess air coefficient in the cylinder, as the ignitability of the fuel dose near the spark plug is a critical factor. The mixture formation of compression ignition based systems are also analyzed. The results of research on indirect and direct injection systems (and their combinations) have been presented. Research sections were separated based to the use of gasoline with other fuels or diesel oil with other fuels. It was found that the use of two fuels in different configurations of the fuel supply systems extends the conditions for the use of modern combustion systems (jet controlled compression ignition, reactivity controlled compression ignition, intelligent charge compression ignition, premixed charge compression ignition), which will enable further improvement of combustion efficiency.

scholarly journals Optical Investigation of a Partial Fuel Stratification Strategy to Stabilize Overall Lean Operation of a DISI Engine Fueled with Gasoline and E30

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 396
Author(s):  
Cinzia Tornatore ◽  
Magnus Sjöberg
Keyword(s):  
Volume Fraction ◽  
Direct Injection ◽  
Combustion Process ◽  
Pilot Injection ◽  
Optical Investigation ◽  
Flame Kernel ◽  
Lean Combustion ◽  
Fuel Stratification ◽  
Spark Plug ◽  
Initial Flame

This paper offers new insights into a partial fuel stratification (PFS) combustion strategy that has proven to be effective at stabilizing overall lean combustion in direct injection spark ignition engines. To this aim, high spatial and temporal resolution optical diagnostics were applied in an optically accessible engine working in PFS mode for two fuels and two different durations of pilot injection at the time of spark: 210 µs and 330 µs for E30 (gasoline blended with ethanol by 30% volume fraction) and gasoline, respectively. In both conditions, early injections during the intake stroke were used to generate a well-mixed lean background. The results were compared to rich, stoichiometric and lean well-mixed combustion with different spark timings. In the PFS combustion process, it was possible to detect a non-spherical and highly wrinkled blue flame, coupled with yellow diffusive flames due to the combustion of rich zones near the spark plug. The initial flame spread for both PFS cases was faster compared to any of the well-mixed cases (lean, stoichiometric and rich), suggesting that the flame propagation for PFS is enhanced by both enrichment and enhanced local turbulence caused by the pilot injection. Different spray evolutions for the two pilot injection durations were found to strongly influence the flame kernel inception and propagation. PFS with pilot durations of 210 µs and 330 µs showed some differences in terms of shapes of the flame front and in terms of extension of diffusive flames. Yet, both cases were highly repeatable.

scholarly journals The Effect of RME-1-Butanol Blends on Combustion, Performance and Emission of a Direct Injection Diesel Engine

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2941
Author(s):  
Wojciech Tutak ◽  
Arkadiusz Jamrozik ◽  
Karol Grab-Rogaliński
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Direct Injection ◽  
Specific Energy Consumption ◽  
Combustion Process ◽  
Constant Load ◽  
Combustion Stability ◽  
Performance And Emission ◽  
Energy Share ◽  
The Stability

The main objective of this study was assessment of the performance, emissions and combustion characteristics of a diesel engine using RME–1-butanol blends. In assessing the combustion process, great importance was placed on evaluating the stability of this process. Not only were the typical COVIMEP indicators assessed, but also the non-burnability of the characteristic combustion stages: ignition delay, time of 50% heat release and the end of combustion. The evaluation of the combustion process based on the analysis of heat release. The tests carried out on a 1-cylinder diesel engine operating at a constant load. Research and evaluation of the combustion process of a mixture of RME and 1-butanol carried out for the entire range of shares of both fuels up to 90% of 1-butanol energetic fraction. The participation of butanol in combustion process with RME increased the in-cylinder peak pressure and the heat release rate. With the increase in the share of butanol there was noted a decrease in specific energy consumption and an increase in engine efficiency. The share of butanol improved the combustion stability. There was also an increase in NOx emissions and decrease in CO and soot emissions. The engine can be power by blend up to 80% energy share of butanol.

scholarly journals Combustion Thermodynamics of Ethanol, n-Heptane, and n-Butanol in a Rapid Compression Machine with a Dual Direct Injection (DDI) Supply System

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2729
Author(s):  
Ireneusz Pielecha ◽  
Sławomir Wierzbicki ◽  
Maciej Sidorowicz ◽  
Dariusz Pietras
Keyword(s):  
Heat Release ◽  
Combustion Chamber ◽  
Internal Combustion Engines ◽  
Direct Injection ◽  
Combustion Process ◽  
Combustion Efficiency ◽  
Injection System ◽  
Rapid Compression Machine ◽  
Process Indicators ◽  
Rapid Compression

The development of internal combustion engines involves various new solutions, one of which is the use of dual-fuel systems. The diversity of technological solutions being developed determines the efficiency of such systems, as well as the possibility of reducing the emission of carbon dioxide and exhaust components into the atmosphere. An innovative double direct injection system was used as a method for forming a mixture in the combustion chamber. The tests were carried out with the use of gasoline, ethanol, n-heptane, and n-butanol during combustion in a model test engine—the rapid compression machine (RCM). The analyzed combustion process indicators included the cylinder pressure, pressure increase rate, heat release rate, and heat release value. Optical tests of the combustion process made it possible to analyze the flame development in the observed area of the combustion chamber. The conducted research and analyses resulted in the observation that it is possible to control the excess air ratio in the direct vicinity of the spark plug just before ignition. Such possibilities occur as a result of the properties of the injected fuels, which include different amounts of air required for their stoichiometric combustion. The studies of the combustion process have shown that the combustible mixtures consisting of gasoline with another fuel are characterized by greater combustion efficiency than the mixtures composed of only a single fuel type, and that the influence of the type of fuel used is significant for the combustion process and its indicator values.

Optical and Numerical Investigations of Flame Propagation in a Heavy Duty Spark Ignited Natural Gas Engine

2021 ◽  
Author(s):  
Jinlong Liu ◽  
Christopher Ulishney ◽  
Cosmin E. Dumitrescu
Keyword(s):  
Natural Gas ◽  
Flame Propagation ◽  
Turbulence Intensity ◽  
Laminar Flame ◽  
Combustion Process ◽  
Combustion Efficiency ◽  
Flame Speed ◽  
Laminar Flame Speed ◽  
Heavy Duty ◽  
Piston Chamber

Abstract Increasing the natural gas (NG) use in heavy-duty engines is beneficial for reducing greenhouse-gas emissions from power generation and transportation. However, converting compression ignition (CI) engines to NG spark ignition operation can increase methane emissions without expensive aftertreatment, thereby defeating the purpose of utilizing a low carbon fuel. The widely accepted explanation for the low combustion efficiency in such retrofitted engines is the lower laminar flame speed of natural gas. In addition, diesel engine’s larger bowl size compared to the traditional gasoline engines increases the flame travel length inside the chamber and extends the combustion duration. However, optical measurements performed in this study suggested that a fast-propagating flame was developed inside the cylinder even at extremely lean operation. This was supported by a three-dimensional numerical simulation, which indicated that the squish region of the bowl-in-piston chamber generated a high turbulence intensity inside the bowl. However, the flame propagation experienced a sudden 2.25x reduction in speed when transiting from the bowl to the squish region. Such a phenomenon was caused by the large decrease in the turbulence intensity inside the squish region during the combustion process. Moreover, the squish volume trapped an important fuel fraction, and it is this fraction that experienced a slow and inefficient burning process during the expansion stroke. This resulted in increased methane emissions and reduced combustion efficiency. Overall, it was the specifics of the combustion process inside a bowl-in-piston chamber not the methane’s slow laminar flame speed that contributed to the low methane combustion efficiency for the retrofitted engine. The results suggest that optimizing the chamber shape is paramount to boost engine efficiency and decrease its emissions.

Analysis of Optimization about the Wall Temperature of the Biomass Fuel Hot Stove

2015 ◽  
Vol 713-715 ◽  
pp. 2981-2984
Author(s):  
Xi Yu Lin ◽  
Guo Min Fu ◽  
Wei Lv ◽  
Chao Cheng
Keyword(s):  
Rural Areas ◽  
Amorphous Materials ◽  
Combustion Process ◽  
Combustion Efficiency ◽  
Biomass Fuel ◽  
Combustion Stability ◽  
Mechanical Pressure ◽  
Existing Problems ◽  
Biomass Resources ◽  
Working Principle

<p>This paper introduces the structure and working principle of biomass fuel hot stove, and analyses the existing problems in the combustion process. Simultaneously, the paper proposes the optimization about the wall high temperature of the hot stove, which is the main issue in the hot stove.</p> <p>Biomass resources in China is very abundant.only the amount of resources of agricultural wastes (such as straw) each year is equivalent to 3.08 tons of standard coal. The biomass briquette is compressed with loose, amorphous materials, such as straw, rice husk, sawdust, wood chips, into a shaped, denser solid fuel with the method of mechanical pressure. It has the advantages of small size, high density, easy storage and transportation, combustion stability, long cycle, high combustion efficiency, low contaminant levels in ash and flue gas. It provides an effective way to solve the energy shortage in rural areas and straw burning problem fundamentally[1].</p>

scholarly journals Effect of Injection Strategies in Diesel/NG Direct-Injection Engines on the Combustion Process and Emissions under Low-Load Operating Conditions

Energies ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 990 ◽  
Author(s):  
Jinze Li ◽  
Longfei Deng ◽  
Jianjun Guo ◽  
Min Zhang ◽  
Zhenyuan Zi ◽  
...  
Keyword(s):  
Thermal Efficiency ◽  
Direct Injection ◽  
Combustion Process ◽  
Combustion Efficiency ◽  
Operating Conditions ◽  
Diffusion Combustion ◽  
Combustion Mode ◽  
Low Load ◽  
Hc Emissions ◽  
Injection Strategies

The direct injection of natural gas (NG), which is an important research direction in the development of NG engines, has the potential to improve thermal efficiency and emissions. When NG engines operate in low-load conditions, combustion efficiency decreases and hydrocarbon (HC) emissions increase due to lean fuel mixtures and slow flame propagation speeds. The effect of two combustion modes (partially premixed compression ignition (PPCI) and high pressure direct injection (HPDI)) on combustion processes was investigated by CFD (Computational Fluid Dynamics), with a focus on different injection strategies. In the PPCI combustion mode, NG was injected early in the compression stroke and premixed with air, and then the pilot diesel was injected to cause ignition near the top dead center. This combustion mode produced a faster heat release rate, but the HC emissions were higher, and the combustion efficiency was lower. In the HPDI combustion mode, the diesel was injected first and ignited, and then the NG was injected into the flame. This combustion mode resulted in higher emissions of NOx and soot, with a diffusion combustion in the cylinder. HC emissions significantly decreased. Compared with PPCI combustion, HPDI had a higher thermal efficiency.

Predictions of Charge Drift in a Concept Electrosprayed DISI Engine

2006 ◽  
Vol 128 (5) ◽  
pp. 903-912 ◽  
Author(s):  
Geraldo C. S. Nhumaio ◽  
A. Paul Watkins
Keyword(s):  
Direct Injection ◽  
Direct Simulation Monte Carlo ◽  
Combustion Efficiency ◽  
Electrical Charge ◽  
Cylinder Wall ◽  
Spark Plug ◽  
Discrete Phase ◽  
Multiple Injection Strategy ◽  
Wall Wetting ◽  
Direct Injection Spark Ignition

Limited to nonvaporizing spray cases, this work discusses the transport of charged droplets within a cylinder of a motored axisymmetric model electrosprayed direct injection spark ignition (eDISI) engine with electrified walls. The concept engine investigated here is assumed to operate with an electrostatic atomizer previously studied for application in fuel burners [Yule et al., 1994, Fuel, 74(7), pp. 1094–1103]. A split/multiple injection strategy is employed in which three pulses of 5mg each are made at crank angles of 80, 150 and 300 deg ATDC of the intake, which fall within the intervals for stable combustion of either early or late injection modes of operation of DISI engines [Jackson et al., 1997, SAE Paper No. 970543]. The direct Simulation Monte Carlo (DSMC) approach embodied in an in-house CFD research code is used to simulate the discrete phase flow with the electrical charge distribution for different instants within the computational cells being computed by simple addition of the droplet charges residing in particular cells at particular instants of time. It is shown in the half engine cycle investigated that the use of charged sprays in eDISI engines may help to reduce the in-cylinder wall-wetting phenomenon. In addition, pockets of highest electrical charge are found to populate the region near the spark plug by 345 deg CA, which may be a path for improved combustion efficiency.

Combustion Characteristics of Stratified Mixture in Lean-Burn LPG Direct-Injection Engine With Spray-Guided Combustion System

2014 ◽  
Author(s):  
Cheolwoong Park ◽  
Seungmook Oh ◽  
Taeyoung Kim ◽  
Heechang Oh ◽  
Choongsik Bae
Keyword(s):  
Fuel Consumption ◽  
Compression Ratio ◽  
Fuel Economy ◽  
Direct Injection ◽  
Combustion Process ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Direct Injection Engine ◽  
Brake Mean Effective Pressure

Today, we are faced with the problems of global warming and fossil fuel depletion, and they have led to the enforcement of new emissions regulations. Direct-injection spark-ignition engines are a very promising technology that can comply with the new regulations. These engines offer the advantages of better fuel economy and lower emissions than conventional port-injection engines. The use of LPG as the fuel reduces carbon emissions because of its vaporization characteristics and the fact that it has lower carbon content than gasoline. An experimental study was carried out to investigate the combustion process and emission characteristics of a 2-liter spray-guided LPG direct-injection engine under lean operating conditions. The engine was operated at a constant speed of 2000 rpm under 0.2-MPa brake mean effective pressure, which corresponds to a common operation point of a passenger vehicle. Combustion stability, which is the most important component of engine performance, is closely related to the operation strategy and it significantly influences the degree of fuel consumption reduction. In order to achieve stable combustion with a stratified LPG mixture, an inter-injection spark ignition (ISI) strategy, which is an alternative control strategy to two-stage injection, was employed. The effects of the compression ratio on fuel economy were also assessed; due to the characteristics of the stratified LPG mixture, the fuel consumption did not reduce when the compression ratio was increased.

Sign in / Sign up

Export Citation Format

Share Document