scholarly journals Effect of Injection Strategies in Diesel/NG Direct-Injection Engines on the Combustion Process and Emissions under Low-Load Operating Conditions

Energies ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 990 ◽  
Author(s):  
Jinze Li ◽  
Longfei Deng ◽  
Jianjun Guo ◽  
Min Zhang ◽  
Zhenyuan Zi ◽  
...  
Keyword(s):  
Thermal Efficiency ◽  
Direct Injection ◽  
Combustion Process ◽  
Combustion Efficiency ◽  
Operating Conditions ◽  
Diffusion Combustion ◽  
Combustion Mode ◽  
Low Load ◽  
Hc Emissions ◽  
Injection Strategies

The direct injection of natural gas (NG), which is an important research direction in the development of NG engines, has the potential to improve thermal efficiency and emissions. When NG engines operate in low-load conditions, combustion efficiency decreases and hydrocarbon (HC) emissions increase due to lean fuel mixtures and slow flame propagation speeds. The effect of two combustion modes (partially premixed compression ignition (PPCI) and high pressure direct injection (HPDI)) on combustion processes was investigated by CFD (Computational Fluid Dynamics), with a focus on different injection strategies. In the PPCI combustion mode, NG was injected early in the compression stroke and premixed with air, and then the pilot diesel was injected to cause ignition near the top dead center. This combustion mode produced a faster heat release rate, but the HC emissions were higher, and the combustion efficiency was lower. In the HPDI combustion mode, the diesel was injected first and ignited, and then the NG was injected into the flame. This combustion mode resulted in higher emissions of NOx and soot, with a diffusion combustion in the cylinder. HC emissions significantly decreased. Compared with PPCI combustion, HPDI had a higher thermal efficiency.

An Investigation of the Combustion Process of a Heavy-Duty Natural Gas-Diesel Dual Fuel Engine

2018 ◽  
Vol 140 (9) ◽  
Author(s):  
Hailin Li ◽  
Shiyu Liu ◽  
Chetmun Liew ◽  
Timothy Gatts ◽  
Scott Wayne ◽  
...  
Keyword(s):  
Thermal Efficiency ◽  
Combustion Process ◽  
Combustion Efficiency ◽  
High Load ◽  
Dual Fuel ◽  
Diffusion Combustion ◽  
Cylinder Pressure ◽  
Brake Thermal Efficiency ◽  
Combustion Duration ◽  
Low Load

This paper investigates the effect of the addition of natural gas (NG) and engine load on the cylinder pressure, combustion process, brake thermal efficiency, and methane combustion efficiency of a heavy-duty NG-diesel dual fuel engine. Significantly increased peak cylinder pressure (PCP) was only observed with the addition of NG at 100% load. The addition of a relatively large amount NG at high load slightly retarded the premixed combustion, significantly increased the peak heat release rate (PHRR) of the diffusion combustion, decreased the combustion duration, and advanced combustion phasing. The accelerated combustion process and increased heat release rate (HRR) at high load were supported by the increased NOx emissions with the addition of over 3% NG (vol.). By comparison, when operated at low load, the addition of a large amount of NG decreased the PHRR of the premixed combustion and slightly increased the PHRR during the late diffusion combustion. Improved brake thermal efficiency was only observed with the addition of a relatively large amount of NG at high load. The improved thermal efficiency was due to a decrease in combustion duration and the shifting of the combustion phasing toward the optimal phasing. The overall combustion efficiency of the dual fuel operation was always lower than diesel-only operation as indicated by the excess emissions of the unburned methane and carbon monoxide from dual fuel engine. This deteriorated the potential of dual fuel engine in further improving the brake thermal efficiency although the combustion duration of dual fuel engine at high load was much shorter than diesel only operation. The addition of NG at low load should be avoided due to the low combustion efficiency of NG and the decreased thermal efficiency. Approaches capable of further improving the in-cylinder combustion efficiency of NG should enable further improvement in the brake thermal efficiency.

scholarly journals Use of Adaptive Injection Strategies to Increase the Full Load Limit of RCCI Operation

2015 ◽  
Author(s):  
Reed Hanson ◽  
Andrew Ickes ◽  
Thomas Wallner
Keyword(s):  
Natural Gas ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Peak Load ◽  
Combustion Process ◽  
Pressure Rise ◽  
Dual Fuel ◽  
The Impact ◽  
Injection Strategies

Dual-fuel combustion using port-injection of low reactivity fuel combined with direct injection of a higher reactivity fuel, otherwise known as Reactivity Controlled Compression Ignition (RCCI), has been shown as a method to achieve low-temperature combustion with moderate peak pressure rise rates, low engine-out soot and NOx emissions, and high indicated thermal efficiency. A key requirement for extending to high-load operation is moderating the reactivity of the premixed charge prior to the diesel injection. One way to accomplish this is to use a very low reactivity fuel such as natural gas. In this work, experimental testing was conducted on a 13L multi-cylinder heavy-duty diesel engine modified to operate using RCCI combustion with port injection of natural gas and direct injection of diesel fuel. Engine testing was conducted at an engine speed of 1200 RPM over a wide variety of loads and injection conditions. The impact on dual-fuel engine performance and emissions with respect to varying the fuel injection parameters is quantified within this study. The injection strategies used in the work were found to affect the combustion process in similar ways to both conventional diesel combustion and RCCI combustion for phasing control and emissions performance. As the load is increased, the port fuel injection quantity was reduced to keep peak cylinder pressure and maximum pressure rise rate under the imposed limits. Overall, the peak load using the new injection strategy was shown to reach 22 bar BMEP with a peak brake thermal efficiency of 47.6%.

An experimental study of the injection strategies on engine performance of the butanol/biodiesel dual-fuel Intelligent Charge Compression Ignition mode

2020 ◽  
pp. 146808742096399
Author(s):  
Wenbin Zhao ◽  
Yaoyuan Zhang ◽  
Guan Huang ◽  
Zilong Li ◽  
Yong Qian ◽  
...  
Keyword(s):  
Heat Release ◽  
Thermal Efficiency ◽  
Direct Injection ◽  
Dual Fuel ◽  
Injection Timing ◽  
Nox Emissions ◽  
Compression Ignition ◽  
Combustion Mode ◽  
Low Levels ◽  
Injection Strategies

Intelligent Charge Compression Ignition (ICCI) combustion mode is a novel dual-fuel combustion strategy that has been proposed recently. In ICCI combustion mode, two fuels with different reactivity are directly injected during the intake stroke and compression stroke, respectively, to achieve flexible reactivity gradient and equivalence ratio stratification. In this study, experiments were conducted on a single-cylinder diesel engine to investigate the effects of butanol direct injection strategies on the engine running with ICCI combustion mode at a constant speed of 1500 r/min and medium load. Results showed that ICCI combustion mode was composed of premixed heat release and diffusion heat release. In compare, the percentage of premixed heat release was higher than the diffusion heat release. With fixed biodiesel direct injection timing (SOI2), retarding butanol single injection timing (SOI1) would delay combustion phasing while not distinctively affect ignition timing. SOI1 showed significant effect on the thermal efficiency and engine emissions. Indicated thermal efficiency (ITE) decreased at first and then slightly increased with retarding of SOI1, while the nitrogen oxides (NOx) emissions were always at low levels. As the butanol second direct injection timing (SOI1-2) retard and the corresponding energy ratio increase, more butanol entered into the crevice/squish regions, leading to the increase of unburned hydrocarbon (HC) and carbon monoxide (CO) emissions. EGR strategy helps to significantly reduce NOx emissions without affecting ITE although penalized HC and CO emissions are resulted in. The optimum butanol direct injection strategies were butanol single direct injection, especially in the early SOI1, in which the thermal efficiency was higher and emissions were at very low levels (NOx  < 0.4 g/kW h).

scholarly journals Combustion Thermodynamics of Ethanol, n-Heptane, and n-Butanol in a Rapid Compression Machine with a Dual Direct Injection (DDI) Supply System

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2729
Author(s):  
Ireneusz Pielecha ◽  
Sławomir Wierzbicki ◽  
Maciej Sidorowicz ◽  
Dariusz Pietras
Keyword(s):  
Heat Release ◽  
Combustion Chamber ◽  
Internal Combustion Engines ◽  
Direct Injection ◽  
Combustion Process ◽  
Combustion Efficiency ◽  
Injection System ◽  
Rapid Compression Machine ◽  
Process Indicators ◽  
Rapid Compression

The development of internal combustion engines involves various new solutions, one of which is the use of dual-fuel systems. The diversity of technological solutions being developed determines the efficiency of such systems, as well as the possibility of reducing the emission of carbon dioxide and exhaust components into the atmosphere. An innovative double direct injection system was used as a method for forming a mixture in the combustion chamber. The tests were carried out with the use of gasoline, ethanol, n-heptane, and n-butanol during combustion in a model test engine—the rapid compression machine (RCM). The analyzed combustion process indicators included the cylinder pressure, pressure increase rate, heat release rate, and heat release value. Optical tests of the combustion process made it possible to analyze the flame development in the observed area of the combustion chamber. The conducted research and analyses resulted in the observation that it is possible to control the excess air ratio in the direct vicinity of the spark plug just before ignition. Such possibilities occur as a result of the properties of the injected fuels, which include different amounts of air required for their stoichiometric combustion. The studies of the combustion process have shown that the combustible mixtures consisting of gasoline with another fuel are characterized by greater combustion efficiency than the mixtures composed of only a single fuel type, and that the influence of the type of fuel used is significant for the combustion process and its indicator values.

Influence of fuel injection strategies on efficiency and particulate emissions of gasoline and ethanol blends in a turbocharged multi-cylinder direct injection engine

2019 ◽  
Vol 22 (1) ◽  
pp. 152-164 ◽  
Author(s):  
Ripudaman Singh ◽  
Taehoon Han ◽  
Mohammad Fatouraie ◽  
Andrew Mansfield ◽  
Margaret Wooldridge ◽  
...  
Keyword(s):  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Timing ◽  
Multiple Injection ◽  
Fuel Mass ◽  
Direct Injection Engine ◽  
Fuel Blends ◽  
Ethanol Blends ◽  
Injection Strategies

The effects of a broad range of fuel injection strategies on thermal efficiency and engine-out emissions (CO, total hydrocarbons, NOx and particulate number) were studied for gasoline and ethanol fuel blends. A state-of-the-art production multi-cylinder turbocharged gasoline direct injection engine equipped with piezoelectric injectors was used to study fuels and fueling strategies not previously considered in the literature. A large parametric space was considered including up to four fuel injection events with variable injection timing and variable fuel mass in each injection event. Fuel blends of E30 (30% by volume ethanol) and E85 (85% by volume ethanol) were compared with baseline E0 (reference grade gasoline). The engine was operated over a range of loads with intake manifold absolute pressure from 800 to 1200 mbar. A combined application of ethanol blends with a multiple injection strategy yielded considerable improvement in engine-out particulate and gaseous emissions while maintaining or slightly improving engine brake thermal efficiency. The weighted injection spread parameter defined in this study, combined with the weighted center of injection timing defined in the previous literature, was found well suited to characterize multiple injection strategies, including the effects of the number of injections, fuel mass in each injection and the dwell time between injections.

scholarly journals Numerical Simulation of Knock Combustion in a Downsizing Turbocharged Gasoline Direct Injection Engine

2019 ◽  
Vol 9 (19) ◽  
pp. 4133 ◽  
Author(s):  
Wang ◽  
Zhang ◽  
Wang ◽  
Han ◽  
Chen
Keyword(s):  
Direct Injection ◽  
Combustion Process ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Gasoline Direct Injection ◽  
Valve Lift ◽  
Fuel Droplets ◽  
Gasoline Direct Injection Engine ◽  
Auto Ignition ◽  
Combustion Simulation

Engine knock has become the prime barrier to significantly improve power density and efficiency of the engines. To further look into the essence of the abnormal combustion, this work studies the working processes of normal combustion and knock combustion under practical engine operating conditions using a three-dimensional computation fluid dynamics (CFD) fluid software CONVERGE (Version 2.3.0, Convergent Science, Inc., Madison, USA). The results show that the tumble in the cylinder is gradually formed with the increase of the valve lift, enhances in the compression stroke and finally is broken due to the extrusion of the piston. The fuel droplets gradually evaporate and move to the intake side under the turbulent and high temperature in the cylinder. During the normal combustion process, the flame propagates faster on the intake side and it facilitates mixture in cylinder combustion. During the knock combustion simulation, the hotspots near the exhaust valve are observed, and the propagating detonation wave caused by multiple hotspots auto-ignition indicates significant effects on knock intensity of in-cylinder pressure.

scholarly journals Use of Adaptive Injection Strategies to Increase the Full Load Limit of RCCI Operation

2016 ◽  
Vol 138 (10) ◽  
Author(s):  
Reed Hanson ◽  
Andrew Ickes ◽  
Thomas Wallner
Keyword(s):  
Natural Gas ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Experimental Testing ◽  
Peak Load ◽  
Combustion Process ◽  
Pressure Rise ◽  
Dual Fuel ◽  
The Impact ◽  
Injection Strategies

Dual-fuel combustion using port-injection of low reactivity fuel combined with direct injection (DI) of a higher reactivity fuel, otherwise known as reactivity controlled compression ignition (RCCI), has been shown as a method to achieve low-temperature combustion with moderate peak pressure rise rates, low engine-out soot and NOx emissions, and high indicated thermal efficiency. A key requirement for extending to high-load operation is moderating the reactivity of the premixed charge prior to the diesel injection. One way to accomplish this is to use a very low reactivity fuel such as natural gas. In this work, experimental testing was conducted on a 13 l multicylinder heavy-duty diesel engine modified to operate using RCCI combustion with port injection of natural gas and DI of diesel fuel. Engine testing was conducted at an engine speed of 1200 rpm over a wide variety of loads and injection conditions. The impact on dual-fuel engine performance and emissions with respect to varying the fuel injection parameters is quantified within this study. The injection strategies used in the work were found to affect the combustion process in similar ways to both conventional diesel combustion (CDC) and RCCI combustion for phasing control and emissions performance. As the load is increased, the port fuel injection (PFI) quantity was reduced to keep peak cylinder pressure (PCP) and maximum pressure rise rate (MPRR) under the imposed limits. Overall, the peak load using the new injection strategy was shown to reach 22 bar brake mean effective pressure (BMEP) with a peak brake thermal efficiency (BTE) of 47.6%.

scholarly journals Some Effects of Hydrogen Self-Ignition and Combustion in Supersonic Flow

2014 ◽  
Vol 16 (2-3) ◽  
pp. 245
Author(s):  
U. Zhapbasbayev ◽  
V. Zabaykin ◽  
Y. Makashev ◽  
A. Tursynbay ◽  
B. Urmashev
Keyword(s):  
Supersonic Flow ◽  
Heat Release ◽  
Chemical Reactions ◽  
Laboratory Data ◽  
Combustion Process ◽  
Supersonic Combustion ◽  
Low Flow ◽  
Diffusion Combustion ◽  
Maximum Pressure ◽  
Combustion Mode

<p>Results are presented of computational and experimental investigations of the influence of temperature and flow composition on the hydrogen combustion kinetics for a coaxial fuel supersonic flow. Depending on the flow parameters, combustion is shown to occur with an intense heat release governed by the speed of chemical reactions, or a diffusion combustion with heat release governed by mixing. The computational results are in good agreements of with laboratory data and portrays many important features of supersonic combustion. The influence of the gas temperature and composition on the diffusion combustion of a circular hydrogen jet in supersonic coaxial flow at the over expanded exhaust regimes is investigated. It is found that at low flow temperatures (Т<sub>2 </sub>~ 900 K) and in the absence of water vapors in the oxidizer gas composition, the speed of chemical reactions is the determining factor for combustion. An increase in the flow temperature (Т<sub>2</sub> &gt; 1200 K) causes a reduction of the induction time of the reactive mixture, because the mixing of fuel with oxidizer decreases, and a “sluggish” diffusion combustion of non-mixed gases is observed. The presence of water vapor and active radicals in the gas ensures the self-ignition from the start of the mixing, and the diffusion combustion mode is limited by mixing of the hydrogen jet with the coaxial flow (similar to the case with high initial temperatures of the air stream). In the case of the delay combustion process the maximum pressure level on the wall is 10% more than that in the combustion mode with ignition at the start of mixing. A sluggish combustion regime may lead to an incomplete hydrogen burnout.</p>

scholarly journals Effects of internal/external EGR and combustion phase on gasoline compression ignition at low-load condition

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Jingyu Gong ◽  
Binbin Yang ◽  
Leilei Liu ◽  
Yue Liang ◽  
Zhifa Zhang ◽  
...  
Keyword(s):  
Thermal Efficiency ◽  
Load Condition ◽  
Soot Emission ◽  
Compression Ignition ◽  
Total Heat Loss ◽  
Engine Model ◽  
Low Load ◽  
Combustion Phase ◽  
Test Engine ◽  
Hc Emissions

Abstract A single-cylinder test engine model was built by GT-Power software, and the effects of internal exhaust gas recirculation (i-EGR), external EGR (e-EGR), i-EGR/e-EGR coupling and the crank angle degree at which 50% of total heat loss has taken place (CA50) on combustion and emission characteristics of gasoline compression ignition at low-load condition were analysed. The results show that the ignition delay period with e-EGR was extended slightly with the increased EGR ratio, while that with i-EGR strategy first shortened and then extended, and that the optimised indicated thermal efficiency could be achieved using a small amount of i-EGR. With the same EGR ratio, nitrogen oxide (NO X ) emission is more likely to be suppressed by i-EGR, while soot emission was more deteriorated, and the superior trade-off relationship between carbon monoxide (CO)/hydrocarbon (HC) emissions and NO X emission was attained by the combination of lower i-EGR ratios and CA50 closed to top dead centre. When using i-EGR/e-EGR coupling with total EGR ratio being fixed, the indicated thermal efficiency was decreased by increasing i-EGR ratio, while the lower NO X , CO and HC emissions could be realised, but only with the consequence that soot emission increased.

A New Predictive ID Model for Advanced High Speed Direct Injection Diesel Engines

2004 ◽  
Author(s):  
Lurun Zhong ◽  
Naeim A. Henein ◽  
Walter Bryzik
Keyword(s):  
Diesel Engines ◽  
High Speed ◽  
Direct Injection ◽  
Combustion Process ◽  
Operating Conditions ◽  
Injection System ◽  
Injection Timing ◽  
Common Rail Injection System ◽  
Common Rail Injection ◽  
Starting Conditions

Advance high speed direct injection diesel engines apply high injection pressures, exhaust gas recirculation (EGR), injection timing and swirl ratios to control the combustion process in order to meet the strict emission standards. All these parameters affect, in different ways, the ignition delay (ID) which has an impact on premixed, mixing controlled and diffusion controlled combustion fractions and the resulting engine-out emissions. In this study, the authors derive a new correlation to predict the ID under the different operating conditions in advanced diesel engines. The model results are validated by experimental data in a single-cylinder, direct injection diesel engine equipped with a common rail injection system at different speeds, loads, EGR ratios and swirl ratios. Also, the model is used to predict the performance of two other diesel engines under cold starting conditions.

Sign in / Sign up

Export Citation Format

Share Document