Effect of Fuel Injection Pressure and Preheating on the Performance and Emissions of a Vegetable Oil Fuelled Diesel Engine

2004 ◽  
Author(s):  
Pugazhvadivu Serane ◽  
Jeyachandran Krishnamurthy
Keyword(s):  
Diesel Engine ◽  
Vegetable Oil ◽  
Fuel Injection ◽  
Direct Injection ◽  
Specific Energy Consumption ◽  
Injection Pressure ◽  
Operating Conditions ◽  
Frying Oil ◽  
Waste Frying Oil ◽  
Performance And Emission

In the present investigation, waste frying oil, a non-edible vegetable oil is used as a diesel fuel substitute. Performance and emission tests were carried out in a naturally aspirated, single cylinder, direct injection diesel engine with and without preheating the waste frying oil and with fuel injection pressures of 190 bar, 210 bar, 230 bar and 250 bar. Performance parameters such as brake specific energy consumption and brake thermal efficiency and emission parameters such as NOx and smoke density were evaluated at various operating conditions. Increasing the injection pressure with and without preheating the fuel is found to improve the performance and reduce smoke emissions. At these conditions, the NOx concentration is seen to increase, however it is lower than pure diesel operation.

Performance and Emission Characteristics of a Diesel Engine with Various Injection Pressures Using Bael Biodiesel

2014 ◽  
Vol 592-594 ◽  
pp. 1714-1718 ◽  
Author(s):  
A. Dhanamurugan ◽  
R. Subramanian
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Brake Thermal Efficiency ◽  
Performance And Emission ◽  
Fuel Jet ◽  
Biodiesel Blend ◽  
Fuel Consumption And Emissions ◽  
Injection Pressures

Fuel injection pressures in diesel engines play an important role to distribute the fuel jet quickly and to form a uniform gas mixture after fuel injection in order to reduce fuel consumption and emissions. In this study, an attempt has been made to study the effect of injection pressure on a single cylinder direct injection diesel engine fueled with diesel, diesel – bael biodiesel blend (B20) and methyl ester of bael (Aegle marmelos) seed oil with injection pressures of 220,230,240 and 250 bar. Increasing the injector opening pressure has been found to increase brake thermal efficiency and reduce CO, HC and smoke emissions significantly. The optimum injection pressure was found to be 240 bar for bael seed biodiesel.

scholarly journals The Effect of RME-1-Butanol Blends on Combustion, Performance and Emission of a Direct Injection Diesel Engine

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2941
Author(s):  
Wojciech Tutak ◽  
Arkadiusz Jamrozik ◽  
Karol Grab-Rogaliński
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Direct Injection ◽  
Specific Energy Consumption ◽  
Combustion Process ◽  
Constant Load ◽  
Combustion Stability ◽  
Performance And Emission ◽  
Energy Share ◽  
The Stability

The main objective of this study was assessment of the performance, emissions and combustion characteristics of a diesel engine using RME–1-butanol blends. In assessing the combustion process, great importance was placed on evaluating the stability of this process. Not only were the typical COVIMEP indicators assessed, but also the non-burnability of the characteristic combustion stages: ignition delay, time of 50% heat release and the end of combustion. The evaluation of the combustion process based on the analysis of heat release. The tests carried out on a 1-cylinder diesel engine operating at a constant load. Research and evaluation of the combustion process of a mixture of RME and 1-butanol carried out for the entire range of shares of both fuels up to 90% of 1-butanol energetic fraction. The participation of butanol in combustion process with RME increased the in-cylinder peak pressure and the heat release rate. With the increase in the share of butanol there was noted a decrease in specific energy consumption and an increase in engine efficiency. The share of butanol improved the combustion stability. There was also an increase in NOx emissions and decrease in CO and soot emissions. The engine can be power by blend up to 80% energy share of butanol.

Influence of Injection Pressure on Performance and Emission Characteristics of Nerium Methyl Ester Operated DI Diesel Engine

2014 ◽  
Vol 592-594 ◽  
pp. 1632-1637
Author(s):  
Ramalingam Senthil ◽  
C. Paramasivam ◽  
Rajendran Silambarasan
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Fuel Injection ◽  
Cetane Number ◽  
Load Condition ◽  
Injection Pressure ◽  
Emission Characteristics ◽  
Operational Parameters ◽  
Performance And Emission ◽  
Standard Design

Nerium methyl ester, an esterified biofuel, has an excellent cetane number and a reasonable calorific value. It closely resembles the behaviour of diesel. However, being a fuel of different origin, the standard design limits of a diesel engine is not suitable for Nerium methyl ester (NME). Therefore, in this work, a set of design and operational parameters are studied to find out the optimum performance of Nerium methyl ester run diesel engine. This work targets at finding the effects of the engine design parameter viz. fuel injection pressure (IP) on the performance with regard to specific fuel consumption (SFC), brake thermal efficiency (BTHE) and emissions of CO, CO2, HC, NOxwith N20 as fuel. Comparison of performance and emission was done for different values of injection pressure to find best possible condition for operating engine with NME. For small sized direct injection constant speed engines used for agricultural applications, the optimum injection pressure was found as 240bar.Methyl esters from Nerium, with properties close to diesel; show better performance and emission characteristics. Hence Nerium (N20) blend can be used in existing diesel engines without compromising the engine performance. Diesel (25%) thus saved will greatly help the interests of railways in meeting the demand for fuel,as diesel trains are operated at maximum load condition.

Experimental Evaluation of Compression Ignition Engine Fueled with Cashew Nut Shell Liquid Diesel Blend with the Effect of Various Injection Pressures

2015 ◽  
Vol 787 ◽  
pp. 717-721
Author(s):  
Sangeetha Krishnamoorthy ◽  
K. Rajan ◽  
K.R. Senthil Kumar ◽  
M. Prabhahar
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Injection Pressure ◽  
Cashew Nut Shell Liquid ◽  
Compression Ignition Engine ◽  
Brake Thermal Efficiency ◽  
Performance And Emission ◽  
Full Load ◽  
Cashew Nut ◽  
Cashew Nut Shell

This paper investigates the performance and emission characteristics of 20% cashew nut shell liquid (CNSL)-diesel blend (B20) in a direct injection diesel engine. The cashew nut shell liquid was prepared by pyrolysis method. The test was conducted with various nozzle opening pressures like 200 bar, 225 bar and 250 bar at different loads between no load to full load. The results showed that the brake thermal efficiency was increased by 2.54% for B20 with 225 bar at full load. The CO and smoke emissions were decreased by 50% and 14% respectively and the NOx emission were decreased slightly with 225 bar injection pressure compared with 200 bar and 250 bar at full load. On the whole, it is concluded that the B20 CNSL blend can be effectively used as a fuel for diesel engine with 225 bar injection pressure without any modifications.

Evaluation of Fuel Injection Strategies for Biodiesel-Fueled CRDI Engine Development and Particulate Studies

2018 ◽  
Vol 140 (10) ◽  
Author(s):  
Akhilendra Pratap Singh ◽  
Avinash Kumar Agarwal
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Pressure Rise ◽  
Injection Pressure ◽  
Combustion Noise ◽  
Emission Characteristics ◽  
Biodiesel Blends ◽  
Performance And Emission ◽  
Injection Parameters ◽  
Smoke Opacity

Fuel injection parameters such as fuel injection pressure (FIP) and start of main injection (SoMI) timings significantly affect the performance and emission characteristics of a common rail direct injection (CRDI) diesel engine. In this study, a state-of-the-art single cylinder research engine was used to investigate the effects of fuel injection parameters on combustion, performance, emission characteristics, and particulates and their morphology. The experiments were carried out at three FIPs (400, 700, and 1000 bar) and four SoMI timings (4 deg, 6 deg, 8 deg, and 10 deg bTDC) for biodiesel blends [B20 (20% v/v biodiesel and 80% v/v diesel) and B40 (40% v/v biodiesel and 60% v/v diesel)] compared to baseline mineral diesel. The experiments were performed at a constant engine speed (1500 rpm), without pilot injection and exhaust gas recirculation (EGR). The experimental results showed that FIP and SoMI timings affected the in-cylinder pressure and the heat release rate (HRR), significantly. At higher FIPs, the biodiesel blends resulted in slightly higher rate of pressure rise (RoPR) and combustion noise compared to baseline mineral diesel. All the test fuels showed relatively shorter combustion duration at higher FIPs and advanced SoMI timings. The biodiesel blends showed slightly higher NOx and smoke opacity compared to baseline mineral diesel. Lower particulate number concentration at higher FIPs was observed for all the test fuels. However, biodiesel blends showed emission of relatively higher number of particulates compared to baseline mineral diesel. Significantly lower trace metals in the particulates emitted from biodiesel blend fueled engine was an important finding of this study. The particulate morphology showed relatively smaller number of primary particles in particulate clusters from biodiesel exhaust, which resulted in relatively lower toxicity, rendering biodiesel to be more environmentally benign.

Effect of Fuel Injection Pressure and Engine Speed on Performance, Emissions, Combustion, and Particulate Investigations of Gasohols Fuelled Gasoline Direct Injection Engine

2019 ◽  
Vol 142 (4) ◽  
Author(s):  
Nikhil Sharma ◽  
Avinash Kumar Agarwal
Keyword(s):  
Internal Combustion Engines ◽  
Fuel Injection ◽  
Driving Forces ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Operating Conditions ◽  
Gasoline Direct Injection ◽  
Primary Alcohols ◽  
Renewable Fuel

Abstract Fuel availability, global warming, and energy security are the three main driving forces, which determine suitability and long-term implementation potential of a renewable fuel for internal combustion engines for a variety of applications. Comprehensive engine experiments were conducted in a single-cylinder gasoline direct injection (GDI) engine prototype having a compression ratio of 10.5, for gaining insights into application of mixtures of gasoline and primary alcohols. Performance, emissions, combustion, and particulate characteristics were determined at different engine speeds (1500, 2000, 2500, 3000 rpm), different fuel injection pressures (FIP: 40, 80, 120, 160 bars) and different test fuel blends namely 15% (v/v) butanol, ethanol, and methanol blended with gasoline, respectively (Bu15, E15, and M15) and baseline gasoline at a fixed (optimum) spark timing of 24 deg before top dead center (bTDC). For a majority of operating conditions, gasohols exhibited superior characteristics except minor engine performance penalty. Gasohols therefore emerged as serious candidate as a transitional renewable fuel for utilization in the existing GDI engines, without requirement of any major hardware changes.

Performance and Emission Characteristics of Diesel Engine Fuelled with Waste Frying Oil Derived Biodiesel-Petroleum Diesel Blend

2017 ◽  
Vol 32 ◽  
pp. 100-111 ◽  
Author(s):  
Adeyinka Sikiru Yusuff ◽  
Olalekan David Adeniyi ◽  
Moses Aderemi Olutoye ◽  
Uduak George Akpan
Keyword(s):  
Diesel Engine ◽  
Mixed Oxides ◽  
High Viscosity ◽  
Frying Oil ◽  
Composite Catalyst ◽  
Emission Characteristics ◽  
Incipient Wetness Impregnation ◽  
Waste Frying Oil ◽  
Compression Ignition Engine ◽  
Performance And Emission

Direct use of vegetable oil as a fuel on compression ignition engine has been described as impossible, because of its high viscosity and density. Transesterification process and other methods have been identified as ways of reducing these two properties. The high cost of virgin vegetable oils and its competition for food have made the biodiesel unable to compete with fossil diesel and also hike its cost. In order to solve these menaces, in this study, waste frying oil was used as a feedstock for production of biodiesel via transesterification using anthill-eggshell promoted Ni-Co mixed oxides (NiCoAE) as heterogeneous catalyst. The composite catalyst was prepared via incipient wetness impregnation (IWI) method and thermally treated at 1000 °C for 4 h. The developed catalyst was characterized using FTIR and SEM techniques. The biodiesel produced under the favourable reaction conditions was blended with petroleum diesel in three different proportions (B20, B50 and B80) and were tested on diesel engine to evaluate their performance and emission characteristics. The blended fuel containing 20% by volume biodiesel (B20) emitted lowest percentage of CO and CO2. The result obtained herein indicates that the mixture of biodiesel and petroleum diesel containing 20% biodiesel (B20) emitted less carbon monoxide (CO) and carbon dioxide (CO2), thus, indicating best dual fuel combination, which can be used in diesel engines without any adjustment or modification in the engines. This result is in agreement with the findings reported in the literature and Energy Policy Act (EPA) of 1992.

Effect of Injection System Parameters on Performance and Emission Characteristics of a Small Single Cylinder Diesel Engine

2021 ◽  
Vol 18 (2) ◽  
Author(s):  
D.K. Dond ◽  
N.P. Gulhane
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Direct Injection ◽  
Common Rail ◽  
Injection System ◽  
Injection Timing ◽  
Emission Characteristics ◽  
Performance And Emission ◽  
System Parameters ◽  
Main Injection

Limited fossil fuel reservoir capacity and pollution caused by them is the big problem in front of researchers. In the present paper, an attempt was made to find a solution to the same. The conventional fuel injection system was retrofitted with a simple version of the common rail direct injection system for the small diesel engine. Further, the effect of injection system parameters was observed on the performance and emission characteristics of the retrofitted common rail direct injection diesel engine. The parameters such as injection pressure, the start of pilot injection timing, the start of main injection timing and quantity of percentage fuel injection during the pilot and main injection period were considered for experimental investigation. It was observed that all the evaluated parameters were found vital for improving the engine’s performance and emission characteristics. The retrofitted common rail direct injection system shows an average 7% rise in brake thermal efficiency with economic, specific fuel consumption. At the same time, much more reduction in hydrocarbon, carbon monoxide and smoke opacity with a penalty of a slight increase in nitrogen oxides.

Sign in / Sign up

Export Citation Format

Share Document