Immersion Cooling of Power Electronics in Segregated Hydrofluoroether Liquids

2008 ◽  
Author(s):  
Cindy M. Barnes ◽  
Phil E. Tuma
Keyword(s):  
Heat Flux ◽  
High Heat ◽  
Temperature Measurements ◽  
Junction Temperature ◽  
Published Data ◽  
High Heat Flux ◽  
Two Phase ◽  
Maximum Heat ◽  
Dielectric Liquids ◽  
Immersion Cooling

Passive two-phase immersion cooling with dielectric liquids is a well established method of cooling thyristor type power semiconductors. However, the capabilities of this method for cooling high heat flux power semiconductor devices such as insulated gate bipolar transistors (IGBTs) have not been thoroughly explored. This work quantifies the junction-to-fluid thermal resistance of IGBTs soldered to boilers and immersed in the segregated hydrofluoroether liquid C3F7OCH3, one of a class of new dielectric liquids with a low Global Warming Potential. The boilers were square copper heat spreaders with a microporous metallic boiling enhancement coating applied to the wetted surfaces. Bare 0.54cm2 IGBT die were soldered to experimentally-optimized boilers and immersed in saturated C3F7OCH3 liquid at atmospheric pressure. Boiler temperature measurements showed a peak boiler-to-fluid heat transfer coefficient of ∼14W/cm2-K at a die level heat flux of 255 W/cm2. Direct junction temperature measurements yielded junction-to-fluid resistivities of 0.15°C/(W/cm2) at this heat flux and 0.20°C/(W/cm2) at 400 W/cm2, the maximum heat flux studied. These results, coupled with published data for air cooled condensers, show that passive two-phase cooling of power modules may provide junction-to-ambient thermal resistances approximately 25% those of conventional air cooled modules and junction-to-fluid resistances 30%–50% of conventional liquid cooled modules, and similar to emerging direct substrate liquid cooling schemes.

Reliable MOSFET operation using two-phase microfluidics in the presence of high heat flux transients

2011 ◽  
Vol 21 (10) ◽  
pp. 105002 ◽  
Author(s):  
Shiv Govind Singh ◽  
Amit Agrawal ◽  
Siddhartha P Duttagupta
Keyword(s):  
Heat Flux ◽  
High Heat ◽  
High Heat Flux ◽  
Two Phase

Model Predictive Control of a Pumped Two-Phase Cooling System With Microchannel Heat Exchangers

2018 ◽  
Author(s):  
Oyuna Angatkina ◽  
Andrew Alleyne
Keyword(s):  
Heat Flux ◽  
Model Predictive Control ◽  
Predictive Control ◽  
Heat Exchangers ◽  
Cooling System ◽  
High Heat ◽  
High Heat Flux ◽  
Two Phase ◽  
Cooling Systems ◽  
Two Phase Cooling

Two-phase cooling systems provide a viable technology for high–heat flux rejection in electronic systems. They provide high cooling capacity and uniform surface temperature. However, a major restriction of their application is the critical heat flux condition (CHF). This work presents model predictive control (MPC) design for CHF avoidance in two-phase pump driven cooling systems. The system under study includes multiple microchannel heat exchangers in series. The MPC controller performance is compared to the performance of a baseline PI controller. Simulation results show that while both controllers are able to maintain the two-phase cooling system below CHF, MPC has significant reduction in power consumption compared to the baseline controller.

Heat Transfer Enhancement in Compact Phase Change Microchannel Heat Exchangers for High Flux Laser Diodes

2018 ◽  
Author(s):  
Jensen Hoke ◽  
Todd Bandhauer ◽  
Jack Kotovsky ◽  
Julie Hamilton ◽  
Paul Fontejon
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Phase Change ◽  
Flow Boiling ◽  
Laser Diodes ◽  
High Heat ◽  
Heat Fluxes ◽  
High Heat Flux ◽  
Maximum Heat ◽  
Average Maximum

Liquid-vapor phase change heat transfer in microchannels offers a number of significant advantages for thermal management of high heat flux laser diodes, including reduced flow rates and near constant temperature heat rejection. Modern laser diode bars can produce waste heat loads >1 kW cm−2, and prior studies show that microchannel flow boiling heat transfer at these heat fluxes is possible in very compact heat exchanger geometries. This paper describes further performance improvements through area enhancement of microchannels using a pyramid etching scheme that increases heat transfer area by ∼40% over straight walled channels, which works to promote heat spreading and suppress dry-out phenomenon when exposed to high heat fluxes. The device is constructed from a reactive ion etched silicon wafer bonded to borosilicate to allow flow visualization. The silicon layer is etched to contain an inlet and outlet manifold and a plurality of 40μm wide, 200μm deep, 2mm long channels separated by 40μm wide fins. 15μm wide 150μm long restrictions are placed at the inlet of each channel to promote uniform flow rate in each channel as well as flow stability in each channel. In the area enhanced parts either a 3μm or 6μm sawtooth pattern was etched vertically into the walls, which were also scalloped along the flow path with the a 3μm periodicity. The experimental results showed that the 6μm area-enhanced device increased the average maximum heat flux at the heater to 1.26 kW cm2 using R134a, which compares favorably to a maximum of 0.95 kw cm2 dissipated by the plain walled test section. The 3μm area enhanced test sections, which dissipated a maximum of 1.02 kW cm2 showed only a modest increase in performance over the plain walled test sections. Both area enhancement schemes delayed the onset of critical heat flux to higher heat inputs.

Thermal Analysis of Cold Plate for Direct Liquid Cooling of High Performance Servers

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Bharath Ramakrishnan ◽  
Yaser Hadad ◽  
Sami Alkharabsheh ◽  
Paul R. Chiarot ◽  
Bahgat Sammakia
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Thermal Resistance ◽  
High Heat ◽  
High Heat Flux ◽  
Cold Plate ◽  
Liquid Cooling ◽  
Maximum Heat ◽  
Effective Heat ◽  
Cold Plates

Data center energy usage keeps growing every year and will continue to increase with rising demand for ecommerce, scientific research, social networking, and use of streaming video services. The miniaturization of microelectronic devices and an increasing demand for clock speed result in high heat flux systems. By adopting direct liquid cooling, the high heat flux and high power demands can be met, while the reliability of the electronic devices is greatly improved. Cold plates which are mounted directly on to the chips facilitate a lower thermal resistance path originating from the chip to the incoming coolant. An attempt was made in the current study to characterize a commercially available cold plate which uses warm water in carrying the heat away from the chip. A mock package mimicking a processor chip with an effective heat transfer area of 6.45 cm2 was developed for this study using a copper block heater arrangement. The thermo-hydraulic performance of the cold plates was investigated by conducting experiments at varying chip power, coolant flow rates, and coolant temperature. The pressure drop (ΔP) and the temperature rise (ΔT) across the cold plates were measured, and the results were presented as flow resistance and thermal resistance curves. A maximum heat flux of 31 W/cm2 was dissipated at a flow rate of 13 cm3/s. A resistance network model was used to calculate an effective heat transfer coefficient by revealing different elements contributing to the total resistance. The study extended to different coolant temperatures ranging from 25 °C to 45 °C addresses the effect of coolant viscosity on the overall performance of the cold plate, and the results were presented as coefficient of performance (COP) curves. A numerical model developed using 6SigmaET was validated against the experimental findings for the flow and thermal performance with minimal percentage difference.

A Numerical Model of a Reciprocating-Mechanism Driven Heat Loop for Two-Phase High Heat Flux Cooling

2016 ◽  
Vol 8 (4) ◽  
Author(s):  
Olubunmi Popoola ◽  
Ayobami Bamgbade ◽  
Yiding Cao
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Numerical Model ◽  
Performance Optimization ◽  
Numerical Study ◽  
High Heat ◽  
Working Fluid ◽  
High Heat Flux ◽  
Two Phase ◽  
Transfer Device

An effective design option for a cooling system is to use a two-phase pumped cooling loop to simultaneously satisfy the temperature uniformity and high heat flux requirements. A reciprocating-mechanism driven heat loop (RMDHL) is a novel heat transfer device that could attain a high heat transfer rate through a reciprocating flow of the two-phase working fluid inside the heat transfer device. Although the device has been tested and validated experimentally, analytical or numerical study has not been undertaken to understand its working mechanism and provide guidance for the device design. The objective of this paper is to develop a numerical model for the RMDHL to predict its operational performance under different working conditions. The developed numerical model has been successfully validated by the existing experimental data and will provide a powerful tool for the design and performance optimization of future RMDHLs. The study also reveals that the maximum velocity in the flow occurs near the wall rather than at the center of the pipe, as in the case of unidirectional steady flow. This higher velocity near the wall may help to explain the enhanced heat transfer of an RMDHL.

Sign in / Sign up

Export Citation Format

Share Document