Modeling of Temperature Rise in Giant Magnetoresistive (GMR) Sensor During an Electrostatic Discharge (ESD) Event

2003 ◽  
Author(s):  
Yizhang Yang ◽  
Sadegh M. Sadeghipour ◽  
Mehdi Asheghi
Keyword(s):  
Thermal Properties ◽  
Temperature Rise ◽  
Electrostatic Discharge ◽  
Thermal Response ◽  
Human Body Model ◽  
Element Analysis ◽  
Current Voltage ◽  
Source Current ◽  
Reliability Issue ◽  
Gmr Sensor

With the further miniaturization of the GMR heads, the electrostatic discharge (ESD) failure has become the primary reliability issue in manufacturing of these sensors. The Joule heating effect during the ESD events result in both thermal and magnetic damages in GMR heads. In this paper, the thermal response of the GMR read head to the excessive current/voltage during an ESD event is investigated numerically using a 3-D finite element analysis. Unlike the previous studies, the thermal properties of the GMR and Al2O3 gap layers used in the simulation are the experimentally measured values. The temperature-rise in GMR heads under human-body-model (HBM) source current is obtained for a range of GMR dimensions and thermal properties of its constituent materials. The simulation results show that temperature in the GMR element sharply increases as the GMR dimensions are reduced, indicating the future GMR heads are more susceptible to the ESD damages. In addition, thermal properties of the GMR and gap materials play key roles in accurate prediction of the temperature field in GMR head during ESD events.

Self-Heating Modeling of Magnetic Recording Read Head

2005 ◽  
Author(s):  
Y. Yang ◽  
L. Baril ◽  
E. Schreck ◽  
A. Wallash ◽  
M. Asheghi
Keyword(s):  
Magnetic Recording ◽  
Temperature Rise ◽  
Areal Density ◽  
Technical Conference ◽  
Normal Operation ◽  
Electronic Systems ◽  
Element Analysis ◽  
Self Heating ◽  
Read Head ◽  
Gmr Sensor

The performance and reliability of the GMR heads are adversely affected by self-heating due to the aggressive scaling of its dimensions to increase areal density. In this manuscript, the self-heating of the GMR head during the normal operation is investigated. An analytical model is developed to estimate the temperature rise in the GMR sensor due to self-heating for magnetic recording areal densities from 2.8 to 80 Gbits/in2, which agrees well with the FEM simulations. This model is subsequently used to investigate the influence of the GMR head constituent materials’ thermal properties on the device temperature rise. A 3-D finite element analysis was also performed to predict the level of self-heating in lead-overlaid (LOL) design, which agrees well with the experimental data obtained using steady-state and transient measurements.   This paper was also originally published as part of the Proceedings of the ASME 2005 Pacific Rim Technical Conference and Exhibition on Integration and Packaging of MEMS, NEMS, and Electronic Systems.

Thermal Characterization of the 144 nm GMR Layer Using Microfabricated Suspended Structures

2003 ◽  
Author(s):  
Shu Zhang ◽  
Yizhang Yang ◽  
Sadegh M. Sadeghipour ◽  
Mehdi Asheghi
Keyword(s):  
Temperature Rise ◽  
Electrostatic Discharge ◽  
Thermal Characterization ◽  
Normal Operation ◽  
Maximum Temperature ◽  
Multilayer Structures ◽  
Accurate Knowledge ◽  
Gmr Sensor ◽  
Present Effort

The performance and reliability of GMR heads are influenced by the level of temperature rise, which may occur in the device during the normal operation or during an electrostatic discharge (ESD) event. However, the reliable electro-thermal modeling of the GMR sensor to predict the temperature rise, demands an accurate knowledge of the thermal properties of its constituent materials such as Al2O3 passivation and GMR layers. The lateral thermal conductivity of the GMR layer, which has not been measured previously, can largely influence the maximum temperature rise in the GMR sensor. The present effort will be directed at thermal characterization of the CoFe/Cu multilayer structures made of extremely thin periodic layers, using steady-state and frequency domain heating and thermometry in suspended bridges. The measurements are performed on several suspended structures with the lengths and widths in the range of 250 to 500 μm and 16 to 20 μm, respectively.

scholarly journals Numerical Evaluation Of Effective Thermal Properties For Materials With Variable Porosity

2014 ◽  
Vol 61 (3) ◽  
pp. 129-142
Author(s):  
P. Staňák ◽  
J. Sládek ◽  
V. Sládek ◽  
S. Krahulec
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Thermal Properties ◽  
Volume Fraction ◽  
Thermal Analyses ◽  
Matrix Material ◽  
Thermal Response ◽  
Spatial Dimension ◽  
Element Analysis ◽  
Element Method

Abstract In this paper a computational homogenization technique is applied to thermal analyses in porous materials. A volume fraction of pores on the microstructural level is the key factor that changes the macroscopic thermal properties. Thus, the distribution of thermal fields at the macroscopic level is analysed through the incorporation of the microstructural response on the representative volume element (RVE) assuming a uniform distribution of pores. For the numerical analysis the scaled boundary finite element method (SBFEM) is introduced to compute the thermal response of RVE. The SBFEM combines the main advantages of the finite element method (FEM) and the boundary element method (BEM). In this method, only the boundary is discretized with elements leading to the reduction of spatial dimension by one, similarly as in the BEM. It reduces computational efforts in the mesh generation and CPU time. The proposed method is used to study square RVE with a circular and elliptic pore under the thermal load. Dimensions of the pore are varied to obtain different volume fractions of matrix material. Numerical results for effective thermal conductivities obtained via SBFEM modelling show an excellent agreement with the finite element analysis using commercial software COMSOL Multiphysics.

Temperature Rise Times in Pneumatic Tires

1976 ◽  
Vol 4 (3) ◽  
pp. 181-189 ◽  
Author(s):  
S. K. Clark
Keyword(s):  
Heat Transfer ◽  
Thermal Properties ◽  
Temperature Rise ◽  
Thermal Equilibrium ◽  
Transfer Coefficients ◽  
Pneumatic Tire ◽  
Heat Transfer Coefficients ◽  
Idealized Model ◽  
Pneumatic Tires

Abstract An idealized model is proposed for heating of a pneumatic tire. A solution is obtained for the temperature rise of such a model. Using known thermal properties of rubber and known heat transfer coefficients, the time to reach thermal equilibrium is estimated.

scholarly journals Continental vs. Global Niche-Based Modelling of Freshwater Species’ Distributions: How Big Are the Differences in the Estimated Climate Change Effects?

Water ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 816
Author(s):  
Danijela Markovic ◽  
Jörg Freyhof ◽  
Oskar Kärcher
Keyword(s):  
Climate Change ◽  
Thermal Properties ◽  
Safety Margin ◽  
Thermal Response ◽  
Future Climate Change ◽  
Freshwater Species ◽  
Response Curves ◽  
Preferred Temperature ◽  
Continental Scale ◽  
Management Actions

Thermal response curves that depict the probability of occurrence along a thermal gradient are used to derive various species’ thermal properties and abilities to cope with warming. However, different thermal responses can be expected for different portions of a species range. We focus on differences in thermal response curves (TRCs) and thermal niche requirements for four freshwater fishes (Coregonus sardinella, Pungitius pungitius, Rutilus rutilus, Salvelinus alpinus) native to Europe at (1) the global and (2) European continental scale. European ranges captured only a portion of the global thermal range with major differences in the minimum (Tmin), maximum (Tmax) and average temperature (Tav) of the respective distributions. Further investigations of the model-derived preferred temperature (Tpref), warming tolerance (WT = Tmax − Tpref), safety margin (SM = Tpref − Tav) and the future climatic impact showed substantially differing results. All considered thermal properties either were under- or overestimated at the European level. Our results highlight that, although continental analyses have an impressive spatial extent, they might deliver misleading estimates of species thermal niches and future climate change impacts, if they do not cover the full species ranges. Studies and management actions should therefore favor whole global range distribution data for analyzing species responses to environmental gradients.

scholarly journals Multidisciplinary Approaches for Assessing a High Temperature Borehole Thermal Energy Storage Facility at Linköping, Sweden

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4379
Author(s):  
Max Hesselbrandt ◽  
Mikael Erlström ◽  
Daniel Sopher ◽  
Jose Acuna
Keyword(s):  
Thermal Properties ◽  
High Temperature ◽  
Energy Storage ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Thermal Response ◽  
Site Investigation ◽  
Thermal Response Test ◽  
Response Test ◽  
Crystalline Bedrock

Assessing the optimal placement and design of a large-scale high temperature energy storage system in crystalline bedrock is a challenging task. This study applies and evaluates various methods and strategies for pre-site investigation for a potential high temperature borehole thermal energy storage (HT-BTES) system at Linköping in Sweden. The storage is required to shift approximately 70 GWh of excess heat generated from a waste incineration plant during the summer to the winter season. Ideally, the site for the HT-BTES system should be able to accommodate up to 1400 wells to 300 m depth. The presence of major fracture zones, high groundwater flow, anisotropic thermal properties, and thick Quaternary overburden are all factors that play an important role in the performance of an HT-BTES system. Inadequate input data to the modeling and design increases the risk of unsatisfactory performance, unwanted thermal impact on the surroundings, and suboptimal placement of the HT-BTES system, especially in a complex crystalline bedrock setting. Hence, it is crucial that the subsurface geological conditions and associated thermal properties are suitably characterized as part of pre-investigation work. In this study, we utilize a range of methods for pre-site investigation in the greater Distorp area, in the vicinity of Linköping. Ground geophysical methods, including magnetic and Very Low-Frequency (VLF) measurements, are collected across the study area together with outcrop observations and lab analysis on rock samples. Borehole investigations are conducted, including Thermal Response Test (TRT) and Distributed Thermal Response Test (DTRT) measurements, as well as geophysical wireline logging. Drone-based photogrammetry is also applied to characterize the fracture distribution and orientation in outcrops. In the case of the Distorp site, these methods have proven to give useful information to optimize the placement of the HT-BTES system and to inform design and modeling work. Furthermore, many of the methods applied in the study have proven to require only a fraction of the resources required to drill a single well, and hence, can be considered relatively efficient.

Thermo-Mechanical Modeling and Analysis of Equal Channel Angular Pressing

2005 ◽  
Vol 23 ◽  
pp. 263-266 ◽  
Author(s):  
Qing Xiang Pei ◽  
B.H. Hu ◽  
C. Lu
Keyword(s):  
Equal Channel Angular Pressing ◽  
Temperature Rise ◽  
Flow Behavior ◽  
Material Model ◽  
Workpiece Material ◽  
Element Analysis ◽  
Modeling And Analysis ◽  
Die Geometry ◽  
Angular Pressing ◽  
Good Agreement

Thermo-mechanical finite element analysis was carried out to study the deformation behavior and temperature distribution during equal channel angular pressing (ECAP). The material model used is the Johnson-Cook constitution model that can consider the multiplication effect of strain, strain rate, and temperature on the flow stress. The effects of pressing speed, pressing temperature, workpiece material and die geometry on the temperature rise and flow behavior during ECAP process were investigated. The simulated temperature rise due to deformation heating was compared with published experimental results and a good agreement was obtained. Among the various die geometries studied, the two-turn die with 0° round corner generates the highest and most uniform plastic strain in the workpiece.

ELECTROSTATIC DISCHARGE EFFECT ON TMR RECORDING HEAD: A FLEX ON SUSPENSION CAPACITANCE APPROACH

2009 ◽  
Vol 23 (17) ◽  
pp. 3586-3590 ◽  
Author(s):  
NUTTACHAI JUTONG ◽  
APIRAT SIRITARATIWAT ◽  
DUANGPORN SOMPONGSE ◽  
PORNCHAI RAKPONGSIRI
Keyword(s):  
Human Body ◽  
Electrostatic Discharge ◽  
Hard Disk Drives ◽  
Electrical Characteristics ◽  
Disk Drives ◽  
Human Body Model ◽  
Recording Head ◽  
Body Model ◽  
Recording Heads ◽  
First Time

Electrostatic discharge (ESD) effects on GMR recording heads have been reported as the major cause of head failure. Since the information density in hard-disk drives has dramatically increased, the GMR head will be no longer in use. The tunneling magnetoresistive (TMR) read heads are initially introduced for a 100 Gbit/in2 density or more. Though the failure mechanism of ESD in GMR recording heads has not been explicitly understood in detail, a study to protect from this effect has to be done. As the TMR head has been commercially started, the ESD effect must be considered. This is the first time that the TMR equivalent circuit has been reported in order to evaluate the ESD effect. A standard human body model (HBM) is discharged across R+ and R- where the capacitances of flex on suspension (FOS) are varied. It is intriguingly found that the electrical characteristics of the TMR head during the discharge period depend on the discharge position. This may be explained in terms of the asymmetry impedance of TMR by using adapted Thevenin's theory. The effect of FOS components on TMR recording heads is also discussed.

Sign in / Sign up

Export Citation Format

Share Document