Active Control of Unsteady Cavitating Flows in Turbomachinery

2019 ◽  
Author(s):  
Maria Grazia De Giorgi ◽  
Antonio Ficarella ◽  
Donato Fontanarosa
Keyword(s):  
Active Control ◽  
Synthetic Jet ◽  
Hydrodynamic Performance ◽  
Transfer Model ◽  
Thick Sheet ◽  
Dimensionless Frequency ◽  
Pulsation Frequency ◽  
Local Pressure ◽  
Vapor Cavity ◽  
The Impact

Abstract A preliminary 2D numerical investigation of the active control of unsteady cavitation by means of one single synthetic jet actuator (SJA) is presented. The SJA has been applied to hinder the intrinsic instabilities of a cloud cavitating flow of water around a NACA 0015 hydrofoil with an angle of attack of 8° and ambient conditions. It has been placed inside the inception region at a distance of 16% of the chord from the leading edge. Concerning the numerical approach, a Eulerian homogeneous mixture/mass transfer model has been used, in combination with an extended Schnerr-Sauer cavitation model and a Volume of Fluid (VOF) interface tracking method. The synthetic jet has been modeled by means of a user-defined velocity boundary conditions based on a sinusoidal waveform. A sensitivity analysis has been first performed in order to evaluate the influence of the main control parameters, namely the momentum coefficient Cμ, the dimensionless frequency F+ and the jet angle αjet. By combining the cavitating vapor content and the impact on the hydrodynamic performance, the best performing SJA configuration has been retrieved. Then, a deeper analysis of the vapor cavity dynamics and the vorticity field has been conducted in order to understand the modification of the main flow produced by the synthetic jet. The best SJA configuration was observed at Cμ = 0.0002, F+ = 0.309 and αjet = 90°, which led to a reduction of both the average vapor content and the average torsional load in the measure of 34.6% and 17.8% respectively. A reduction of the average pulsation frequency of the pressure upstream confirmed the beneficial effect of the SJA. The analysis of the coupled dynamics between vapor cavity-vorticity and their POD-based modal structures highlighted that the benefit of the SJA lies on preventing the growth of a thick sheet cavity which tends to cause the development of the highly cavitating cloud dynamics after the cavity breakup. This is mainly due to an additional vorticity close to the hydrofoil surface just downstream the SJA, as well as a local pressure modification close the SJA during the blowing stroke.

Active Control of Unsteady Cavitating Flows Over Hydrofoil

2020 ◽  
Vol 142 (11) ◽  
Author(s):  
Maria Grazia De Giorgi ◽  
Donato Fontanarosa ◽  
Antonio Ficarella
Keyword(s):  
Active Control ◽  
Leading Edge ◽  
Suction Side ◽  
Synthetic Jet ◽  
Thick Sheet ◽  
Dimensionless Frequency ◽  
Ambient Conditions ◽  
Local Pressure ◽  
Vapor Cavity ◽  
Momentum Coefficient

Abstract A preliminary two-dimensional (2D) numerical investigation of the active control of unsteady cavitation by means of one single synthetic jet actuator (SJA) is presented. The investigation involves the cloud-cavitating flow of water around a NACA 0015 hydrofoil with an angle of attack of 8-deg and ambient conditions. The SJA locates on the suction side at a distance of 16% of the chord from the leading edge; it has been modeled by means of a user-defined velocity boundary conditions based on a sinusoidal waveform. A Eulerian homogeneous mixture model has been used, coupled with an extended Schnerr–Sauer cavitation model and a volume of fluid interface tracking method. As first, a sensitivity analysis allowed to evaluate the influence of the main control parameters, namely, the momentum coefficient Cμ, the dimensionless frequency F+, and the jet angle αjet. As a result, the best performing SJA configuration was retrieved at Cμ=0.0002, F+=0.309, and αjet=90 deg, which led to a reduction of both the average vapor content and the average torsional load in the measure of 34.6% and 17.8%. The analysis of the coupled dynamics between vapor cavity–vorticity and their proper orthogonal decomposition (POD)-based modal structures highlighted the benefit of the SJA lies in preventing the growth of a thick sheet cavity, which causes the development of the highly cavitating cloud dynamics after the cavity breakup. This is mainly due to an additional vorticity close to the hydrofoil surface just downstream the SJA, as well as a local pressure modification close the SJA during the blowing stroke.

scholarly journals A model sensitivity study of the impact of clouds on satellite detection and retrieval of volcanic ash

2015 ◽  
Vol 8 (5) ◽  
pp. 1935-1949 ◽  
Author(s):  
A. Kylling ◽  
N. Kristiansen ◽  
A. Stohl ◽  
R. Buras-Schnell ◽  
C. Emde ◽  
...  
Keyword(s):  
Radiative Transfer ◽  
Liquid Water ◽  
Volcanic Ash ◽  
Spectral Band ◽  
Sensitivity Study ◽  
Transfer Model ◽  
Mass Loading ◽  
Ice Clouds ◽  
Medium Range Weather Forecast ◽  
The Impact

Abstract. Volcanic ash is commonly observed by infrared detectors on board Earth-orbiting satellites. In the presence of ice and/or liquid-water clouds, the detected volcanic ash signature may be altered. In this paper the sensitivity of detection and retrieval of volcanic ash to the presence of ice and liquid-water clouds was quantified by simulating synthetic equivalents to satellite infrared images with a 3-D radiative transfer model. The sensitivity study was made for the two recent eruptions of Eyjafjallajökull (2010) and Grímsvötn (2011) using realistic water and ice clouds and volcanic ash clouds. The water and ice clouds were taken from European Centre for Medium-Range Weather Forecast (ECMWF) analysis data and the volcanic ash cloud fields from simulations by the Lagrangian particle dispersion model FLEXPART. The radiative transfer simulations were made both with and without ice and liquid-water clouds for the geometry and channels of the Spinning Enhanced Visible and Infrared Imager (SEVIRI). The synthetic SEVIRI images were used as input to standard reverse absorption ash detection and retrieval methods. Ice and liquid-water clouds were on average found to reduce the number of detected ash-affected pixels by 6–12%. However, the effect was highly variable and for individual scenes up to 40% of pixels with mass loading >0.2 g m−2 could not be detected due to the presence of water and ice clouds. For coincident pixels, i.e. pixels where ash was both present in the FLEXPART (hereafter referred to as "Flexpart") simulation and detected by the algorithm, the presence of clouds overall increased the retrieved mean mass loading for the Eyjafjallajökull (2010) eruption by about 13%, while for the Grímsvötn (2011) eruption ash-mass loadings the effect was a 4% decrease of the retrieved ash-mass loading. However, larger differences were seen between scenes (standard deviations of ±30 and ±20% for Eyjafjallajökull and Grímsvötn, respectively) and even larger ones within scenes. The impact of ice and liquid-water clouds on the detection and retrieval of volcanic ash, implies that to fully appreciate the location and amount of ash, hyperspectral and spectral band measurements by satellite instruments should be combined with ash dispersion modelling.

scholarly journals Investigations on Quench Recovery Characteristics of High-Temperature Superconducting Coated Conductors for Superconducting Fault Current Limiters

Electronics ◽  
2021 ◽  
Vol 10 (3) ◽  
pp. 259
Author(s):  
Wei Chen ◽  
Peng Song ◽  
Hao Jiang ◽  
Jiahui Zhu ◽  
Shengnan Zou ◽  
...  
Keyword(s):  
High Temperature ◽  
Smart Grids ◽  
Recovery Time ◽  
Coated Conductors ◽  
Transfer Model ◽  
Fault Current ◽  
High Temperature Superconducting ◽  
Fault Current Limiters ◽  
Recovery Characteristic ◽  
The Impact

Superconducting fault current limiters (SFCLs) are attracting increasing attention due to their potential for use in modern smart grids or micro grids. Thanks to the unique non-linear properties of high-temperature-superconducting (HTS) tapes, an SFCL is invisible to the grid with faster response compared to traditional fault current limiters. The quench recovery characteristic of an HTS tape is fundamental for the design of an SFCL. In this work, the quench recovery time of an HTS tape was measured for fault currents of different magnitudes and durations. A global heat transfer model was developed to describe the quench recovery characteristic and compared with experiments to validate its effectiveness. Based on the model, the influence of tape properties on the quench recovery time was discussed, and a safe margin for the impact energy was proposed.

The Semi-Active Control Considering Structure-Basement-Pile-Soil Interaction

2010 ◽  
Vol 163-167 ◽  
pp. 2780-2786
Author(s):  
Yan Tao Li ◽  
Zhan Xue Zhou
Keyword(s):  
Active Control ◽  
Structural Control ◽  
Soil Structure ◽  
Tall Buildings ◽  
Interaction System ◽  
Subdomain Method ◽  
Infinite Element Method ◽  
Fixed End ◽  
Instantaneous Optimal Control ◽  
The Impact

The interaction system which includes pi1e-supported tall buildings with multistoried basements and the adjacent medium of soil subject to the impact of earthquake is formulated in terms of the spline subdomain method,semi-analytical infinite element method and the bend-shear model of beam element,respectively.Taking advantage of the instantaneous optimal control algorithm, structure-basements-piles-soil interaction effect on the semi-active control is considered. It is shown that the results of structural control have obvious difference between the interaction system and the fixed-end system.The response of the former may be less about 10 percent than the latter in the paper.The dissipative capability of the structure self may be ignored largely if the interaction isn’t considered.When designing the system of the semi-active control, especially for some tall buildings,soil-structure interaction should be taken into consideration.

scholarly journals The impact of residential combustion emissions on atmospheric aerosol, human health, and climate

2016 ◽  
Vol 16 (2) ◽  
pp. 873-905 ◽  
Author(s):  
E. W. Butt ◽  
A. Rap ◽  
A. Schmidt ◽  
C. E. Scott ◽  
K. J. Pringle ◽  
...  
Keyword(s):  
Eastern Europe ◽  
Human Health ◽  
Atmospheric Aerosol ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
So2 Emissions ◽  
Residential Sector ◽  
Residential Combustion ◽  
Combustion Emissions ◽  
The Impact

Abstract. Combustion of fuels in the residential sector for cooking and heating results in the emission of aerosol and aerosol precursors impacting air quality, human health, and climate. Residential emissions are dominated by the combustion of solid fuels. We use a global aerosol microphysics model to simulate the impact of residential fuel combustion on atmospheric aerosol for the year 2000. The model underestimates black carbon (BC) and organic carbon (OC) mass concentrations observed over Asia, Eastern Europe, and Africa, with better prediction when carbonaceous emissions from the residential sector are doubled. Observed seasonal variability of BC and OC concentrations are better simulated when residential emissions include a seasonal cycle. The largest contributions of residential emissions to annual surface mean particulate matter (PM2.5) concentrations are simulated for East Asia, South Asia, and Eastern Europe. We use a concentration response function to estimate the human health impact due to long-term exposure to ambient PM2.5 from residential emissions. We estimate global annual excess adult (>  30 years of age) premature mortality (due to both cardiopulmonary disease and lung cancer) to be 308 000 (113 300–497 000, 5th to 95th percentile uncertainty range) for monthly varying residential emissions and 517 000 (192 000–827 000) when residential carbonaceous emissions are doubled. Mortality due to residential emissions is greatest in Asia, with China and India accounting for 50 % of simulated global excess mortality. Using an offline radiative transfer model we estimate that residential emissions exert a global annual mean direct radiative effect between −66 and +21 mW m−2, with sensitivity to the residential emission flux and the assumed ratio of BC, OC, and SO2 emissions. Residential emissions exert a global annual mean first aerosol indirect effect of between −52 and −16 mW m−2, which is sensitive to the assumed size distribution of carbonaceous emissions. Overall, our results demonstrate that reducing residential combustion emissions would have substantial benefits for human health through reductions in ambient PM2.5 concentrations.

scholarly journals A Mathematical Model for Swallowing of Concentrated Fluids in Oesophagus

2011 ◽  
Vol 8 (3-4) ◽  
pp. 309-321 ◽  
Author(s):  
S. K. Pandey ◽  
Dharmendra Tripathi
Keyword(s):  
Mathematical Model ◽  
Flow Rate ◽  
Plug Flow ◽  
Flow Region ◽  
Mechanical Efficiency ◽  
Casson Fluid ◽  
Local Pressure ◽  
Integral Number ◽  
Tomato Puree ◽  
The Impact

This model investigates particularly the impact of an integral and a non-integral number of waves on the swallowing of food stuff such as jelly, tomato puree, soup, concentrated fruits juices and honey transported peristaltically through the oesophagus. The fluid is considered as a Casson fluid. Emphasis is on the study of the dependence of local pressure distribution on space and time. Mechanical efficiency, reflux limit and trapping are also discussed. The effect of Casson fluid vis-à-vis Newtonian fluid is investigated analytically and numerically too. The result is physically interpreted as that the oesophagus makes more efforts to swallow fluids with higher concentration. It is observed that the pressure is uniformly distributed when an integral number of waves is there in the oesophagus; but it is non-uniform when a non-integral number of waves is present therein. It is further observed that as the plug flow region widens, the pressure difference increases, which indicates that the averaged flow rate will reduce for a Casson fluid. It is also concluded that Casson fluids are more prone to reflux.

scholarly journals Analysis of actinic flux profiles measured from an ozonesonde balloon

2015 ◽  
Vol 15 (8) ◽  
pp. 4131-4144 ◽  
Author(s):  
P. Wang ◽  
M. Allaart ◽  
W. H. Knap ◽  
P. Stammes
Keyword(s):  
Atmospheric Chemistry ◽  
Low Cost ◽  
Green Light ◽  
Single Layer ◽  
Radiative Transfer Model ◽  
Cloud Base ◽  
Transfer Model ◽  
Actinic Flux ◽  
Clear Sky ◽  
The Impact

Abstract. A green light sensor has been developed at KNMI to measure actinic flux profiles using an ozonesonde balloon. In total, 63 launches with ascending and descending profiles were performed between 2006 and 2010. The measured uncalibrated actinic flux profiles are analysed using the Doubling–Adding KNMI (DAK) radiative transfer model. Values of the cloud optical thickness (COT) along the flight track were taken from the Spinning Enhanced Visible and Infrared Imager (SEVIRI) Cloud Physical Properties (CPP) product. The impact of clouds on the actinic flux profile is evaluated on the basis of the cloud modification factor (CMF) at the cloud top and cloud base, which is the ratio between the actinic fluxes for cloudy and clear-sky scenes. The impact of clouds on the actinic flux is clearly detected: the largest enhancement occurs at the cloud top due to multiple scattering. The actinic flux decreases almost linearly from cloud top to cloud base. Above the cloud top the actinic flux also increases compared to clear-sky scenes. We find that clouds can increase the actinic flux to 2.3 times the clear-sky value at cloud top and decrease it to about 0.05 at cloud base. The relationship between CMF and COT agrees well with DAK simulations, except for a few outliers. Good agreement is found between the DAK-simulated actinic flux profiles and the observations for single-layer clouds in fully overcast scenes. The instrument is suitable for operational balloon measurements because of its simplicity and low cost. It is worth further developing the instrument and launching it together with atmospheric chemistry composition sensors.

scholarly journals Control of a Round Jet Intermittency and Transition to Turbulence by Means of an Annular Synthetic Jet

Actuators ◽  
2021 ◽  
Vol 10 (8) ◽  
pp. 185
Author(s):  
Zuzana Antošová ◽  
Zdeněk Trávníček
Keyword(s):  
Reynolds Number ◽  
Active Control ◽  
Flow Regimes ◽  
Velocity Profiles ◽  
Synthetic Jet ◽  
Transition To Turbulence ◽  
Jet Flows ◽  
Maximal Effect ◽  
Hot Wire ◽  
Round Jet

This paper deals with active control of a continuous jet issuing from a long pipe nozzle by means of a concentrically placed annular synthetic jet. The experiments in air cover regimes of laminar, transitional, and turbulent main jet flows (Reynolds number ranges 1082–5181). The velocity profiles (time-mean and fluctuation components) of unforced and forced jets were measured using hot-wire anemometry. Six flow regimes are distinguished, and their parameter map is proposed. The possibility of turbulence reduction by forcing in transitional jets is demonstrated, and the maximal effect is revealed at Re = 2555, where the ratio of the turbulence intensities of the forced and unforced jets is decreased up to 0.45.

scholarly journals Data-Driven Localization Mappings in Filtering the Monsoon–Hadley Multicloud Convective Flows

2018 ◽  
Vol 146 (4) ◽  
pp. 1197-1218
Author(s):  
Michèle De La Chevrotière ◽  
John Harlim
Keyword(s):  
Learning Algorithm ◽  
Data Driven ◽  
Radiative Transfer Model ◽  
Transfer Model ◽  
Model Errors ◽  
Accurate Analysis ◽  
Perfect Model ◽  
Nonlinear Stochastic Model ◽  
Correlation Statistics ◽  
The Impact

This paper demonstrates the efficacy of data-driven localization mappings for assimilating satellite-like observations in a dynamical system of intermediate complexity. In particular, a sparse network of synthetic brightness temperature measurements is simulated using an idealized radiative transfer model and assimilated to the monsoon–Hadley multicloud model, a nonlinear stochastic model containing several thousands of model coordinates. A serial ensemble Kalman filter is implemented in which the empirical correlation statistics are improved using localization maps obtained from a supervised learning algorithm. The impact of the localization mappings is assessed in perfect-model observing system simulation experiments (OSSEs) as well as in the presence of model errors resulting from the misspecification of key convective closure parameters. In perfect-model OSSEs, the localization mappings that use adjacent correlations to improve the correlation estimated from small ensemble sizes produce robust accurate analysis estimates. In the presence of model error, the filter skills of the localization maps trained on perfect- and imperfect-model data are comparable.

Sign in / Sign up

Export Citation Format

Share Document