Multidisciplinary Design of a Three Stage High Speed Booster

2017 ◽  
Author(s):  
Marcus Lejon ◽  
Tomas Grönstedt ◽  
Nenad Glodic ◽  
Paul Petrie-Repar ◽  
Magnus Genrup ◽  
...  
Keyword(s):  
Conceptual Design ◽  
High Speed ◽  
High Efficiency ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Design Tool ◽  
Test Case ◽  
Engine Thrust ◽  
Final Design ◽  
Definition Of

The paper describes a multidisciplinary conceptual design of an axial compressor, targeting a three stage, high speed, high efficiency booster with a design pressure ratio of 2.8. The paper is outlined in a step wise manner starting from basic aircraft and engine thrust requirements, establishing the definition of the high speed booster interface points and its location in the engine. Thereafter, the aerodynamic 1D/2D design is carried out using the commercial throughflow tool SC90C. A number of design aspects are described, and the steps necessary to arrive at the final design are outlined. The SC90C based design is then carried over to a CFD based conceptual design tool AxCent, in which a first profiling is carried out based on a multiple circular arc blade definition. The design obtained at this point is referred to as the VINK compressor. The first stage of the compressor is then optimized using an in-house optimization tool, where the objective functions are evaluated from detailed CFD calculations. The design is improved in terms of efficiency and in terms of meeting the design criteria put on the stage in the earlier design phases. Finally, some aeromechanical design aspects of the first stage are considered. The geometry and inlet boundary conditions of the compressor are shared with the turbomachinery community on a public server. This is intended to be used as a test case for further optimization and analysis.

Characteristics of Stable Rotating Stall Cells in an Axial Compressor

2017 ◽  
Author(s):  
Adam R. Hickman ◽  
Scott C. Morris
Keyword(s):  
Flow Field ◽  
High Speed ◽  
Pressure Ratio ◽  
Pressure Sensors ◽  
Axial Compressor ◽  
Field Measurements ◽  
Rotating Stall ◽  
Flow Coefficient ◽  
Stable Operation ◽  
Double Phase

Flow field measurements of a high-speed axial compressor are presented during pre-stall and post-stall conditions. The paper provides an analysis of measurements from a circumferential array of unsteady shroud static pressure sensors during stall cell development. At low-speed, the stall cell approached a stable size in approximately two rotor revolutions. At higher speeds, the stall cell developed within a short amount of time after stall inception, but then fluctuated in circumferential extent as the compressor transiently approached a stable post-stall operating point. The size of the stall cell was found to be related to the annulus average flow coefficient. A discussion of Phase-Locked Average (PLA) statistics on flow field measurements during stable operation is also included. In conditions where rotating stall is present, flow field measurements can be Double Phase-Locked Averaged (DPLA) using a once-per-revolution (1/Rev) pulse and the period of the stall cell. The DPLA method provides greater detail and understanding into the structure of the stall cell. DPLA data indicated that a stalled compressor annulus can be considered to contained three main regions: over-pressurized passages, stalled passages, and recovering passages. Within the over-pressured region, rotor passages exhibited increased blade loading and pressure ratio compared to pre-stall values.

Shock Tube Simulation of the Transient Surge Phase Inside an Axial Compressor

2018 ◽  
Author(s):  
Paul Xiubao Huang ◽  
Robert S. Mazzawy
Keyword(s):  
Shock Wave ◽  
Shock Tube ◽  
High Speed ◽  
Transient Flow ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Dynamic Effect ◽  
Initiation Site ◽  
Flow Reversal ◽  
Expansion Waves

This paper is a continuing work from one author on the same topic of the transient aerodynamics during compressor stall/surge using a shock tube analogy by Huang [1, 2]. As observed by Mazzawy [3] for the high-speed high-pressure (HSHP) ratio compressors of the modern aero-engines, surge is an event characterized with the stoppage and reversal of engine flow within a matter of milliseconds. This large flow transient is accomplished through a pair of internally generated shock waves and expansion waves of high strength. The final results are often dramatic with a loud bang followed by the spewing out of flames from both the engine intake and exhaust, potentially damaging to the engine structure [3]. It has been demonstrated in the previous investigations by Marshall [4] and Huang [2] that the transient flow reversal phase of a surge cycle can be approximated by the shock tube analogy in understanding its generation mechanism and correlating the shock wave strength as a function of the pre-surge compressor pressure ratio. Kurkov [5] and Evans [8] used a guillotine analogy to estimate the inlet overpressure associated with the sudden flow stoppage associated with surge. This paper will expand the progressive surge model established by the shock tube analogy in [2] by including the dynamic effect of airflow stoppage using an “integrated-flow” sequential guillotine/shock tube model. It further investigates the surge formation (characterized by flow reversal) and propagation patterns (characterized by surge shock and expansion waves) after its generation at different locations inside a compressor. Calculations are conducted for a 12-stage compressor using this model under various surge onset stages and compared with previous experimental data [3]. The results demonstrate that the “integrated-flow” model closely replicates the fast moving surge shock wave overpressure from the stall initiation site to the compressor inlet.

Performance of Strongly Bowed Stators in a Four-Stage High-Speed Compressor

2004 ◽  
Vol 126 (3) ◽  
pp. 333-338 ◽  
Author(s):  
Axel Fischer ◽  
Walter Riess ◽  
Joerg R. Seume
Keyword(s):  
Mass Flow ◽  
High Speed ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Maximum Pressure ◽  
Controlled Diffusion ◽  
Stage 4 ◽  
The University

The FVV sponsored project “Bow Blading” (cf. acknowledgments) at the Turbomachinery Laboratory of the University of Hannover addresses the effect of strongly bowed stator vanes on the flow field in a four-stage high-speed axial compressor with controlled diffusion airfoil (CDA) blading. The compressor is equipped with more strongly bowed vanes than have previously been reported in the literature. The performance map of the present compressor is being investigated experimentally and numerically. The results show that the pressure ratio and the efficiency at the design point and at the choke limit are reduced by the increase in friction losses on the surface of the bowed vanes, whose surface area is greater than that of the reference (CDA) vanes. The mass flow at the choke limit decreases for the same reason. Because of the change in the radial distribution of axial velocity, pressure rise shifts from stage 3 to stage 4 between the choke limit and maximum pressure ratio. Beyond the point of maximum pressure ratio, this effect is not distinguishable from the reduction of separation by the bow of the vanes. Experimental results show that in cases of high aerodynamic loading, i.e., between maximum pressure ratio and the stall limit, separation is reduced in the bowed stator vanes so that the stagnation pressure ratio and efficiency are increased by the change to bowed stators. It is shown that the reduction of separation with bowed vanes leads to a increase of static pressure rise towards lower mass flow so that the present bow bladed compressor achieves higher static pressure ratios at the stall limit.

scholarly journals Reverse Thrust Aerodynamics of Variable Pitch Fans

2018 ◽  
Author(s):  
Tim S. Williams ◽  
Cesare A. Hall
Keyword(s):  
High Speed ◽  
Pressure Ratio ◽  
Test Case ◽  
Suction Surface ◽  
Flow Angle ◽  
Variable Pitch ◽  
Open Rotor ◽  
Weight Penalty ◽  
Reverse Thrust ◽  
Rotor Loss

Variable pitch fans are of interest for future low pressure ratio fan systems since they provide improved operability relative to fixed pitch fans. If they can also be re-pitched such that they generate sufficient reverse thrust they could eliminate the engine drag and weight penalty associated with bypass duct thrust reversers. This paper sets out to understand the details of the 3D fan stage flow field in reverse thrust operation. The study uses the Advanced Ducted Propulsor variable pitch fan test case, which has a design fan pressure ratio of 1.29. Comparison with spanwise probe measurements show that the computational approach is valid for examining the variation of loss and work in the rotor in forward thrust. The method is then extended to a reverse thrust configuration using an extended domain and appropriate boundary conditions. Computations, run at two rotor stagger settings, show that the spanwise variation in relative flow angle onto the rotor aligns poorly to the rotor inlet metal angle. This leads to two dominant rotor loss sources: one at the tip associated with positive incidence, and the second caused by negative incidence at lower span fractions. The second loss is reduced by opening the rotor stagger setting, and the first increases with rotor suction surface Mach number. The higher mass flow at more open rotor settings provide higher gross thrust, up to 49% of the forward take-off value, but is limited by the increased loss at high speed.

Innovative Multiple Matching Charts approach to support the conceptual design of hypersonic vehicles

2020 ◽  
Vol 234 (12) ◽  
pp. 1893-1912
Author(s):  
Davide Ferretto ◽  
Roberta Fusaro ◽  
Nicole Viola
Keyword(s):  
Conceptual Design ◽  
High Speed ◽  
Graphical Representation ◽  
Weight Ratio ◽  
Transportation Systems ◽  
Flight Vehicles ◽  
Performance Requirements ◽  
Reference Vehicle ◽  
Vehicle Configuration ◽  
Definition Of

Several well-established best practices and reliable tools have been developed along the years to support aircraft conceptual and preliminary design. In this context, one of the most widely used tool is the Matching Chart (MC), a graphical representation of the different performance requirements (curves representing the thrust-to-weight ratio (T/W) requirement as function of the wing loading (W/S)) for each mission phase. The exploitation of this tool allows the identification of a feasible design space as well as the definition of a reference vehicle configuration in terms of maximum thrust, maximum take-off weight, and wing surface since the very beginning of the design process. Although the tool was originally developed for conventional aircraft, several extensions and updates of the mathematical models have been proposed over the years to widen its application to innovative configurations. Following this trend, this paper presents a further evolution of the MC model to support the conceptual design of high-speed transportation systems, encompassing supersonic and hypersonic flight vehicles. At this purpose, this paper reports and discusses the updates of the methodology laying behind the generation of the MC for high-speed transportation. Eventually, the results of the validation of the updated methodology and tool are reported, using as case study, the STRATOFLY MR3 vehicle configuration, a Mach 8 antipodal civil transportation system, currently under development within the H2020 STRATOFLY project.

Off-Design Prediction of Transonic Axial Compressors: Part 1 — Mean-Line Code and Tuning Factors

2018 ◽  
Author(s):  
John Kidikian ◽  
Marcelo Reggio
Keyword(s):  
Pressure Ratio ◽  
Axial Compressor ◽  
Design Tool ◽  
Information Storage ◽  
Axial Compressors ◽  
Design Performance ◽  
Engineering Software ◽  
Line Loss ◽  
Loss Modelling ◽  
Line Analysis

With yearly advances in CFD techniques and methodologies, and the increased capacity and capabilities of computer CPU, GPU, and information storage, CFD has become a powerful design tool. However, despite its vast strengths, a CFD analysis is still based on the sound development of the 1D mean-line analysis methodology. This paper (part 1 of 2) describes an off-design axial compressor mean-line code, tested in a specialized engineering software for the development and analysis of a whole gas turbine engine, and the various tuning factors used to obtain an off-design performance match. It will be shown that, to obtain a proper match of the off-design performance of single-stage transonic axial compressors, both the rotor and stage pressure ratio, and the rotor temperature ratio are required to be converged upon. To do so, the off-design mean-line analysis requires the incorporation of a set of inlet & exit blockage factors and deviation angles that vary with the compressor performance conditions. This approach differs from the literature-based procedural assumptions (or rule-of-thumb) of fixed inlet and exit blockage factors of approximately “0.98”, and the use of a unique deviation angle based on Carter’s rule. The results obtained in this paper are then used to develop a generalized off-design mean-line loss modelling methodology (part 2 of 2) capable of predicting the off-design performance of four well documented NASA transonic axial compressors.

scholarly journals Numerical Optimization of a Stall Margin Enhancing Recirculation Channel for an Axial Compressor

Fluids ◽  
2019 ◽  
Vol 4 (2) ◽  
pp. 88
Author(s):  
Motoyuki Kawase ◽  
Aldo Rona
Keyword(s):  
High Speed ◽  
High Performance ◽  
Fluid Dynamic ◽  
Axial Compressor ◽  
Leading Edge ◽  
Navier Stokes ◽  
Test Case ◽  
Dynamic Simulations ◽  
Stall Margin ◽  
Casing Treatment

A proof of concept is provided by computational fluid dynamic simulations of a new recirculating type casing treatment. This treatment aims at extending the stable operating range of highly loaded axial compressors, so to improve the safety of sorties of high-speed, high-performance aircraft powered by high specific thrust engines. This casing treatment, featuring an axisymmetric recirculation channel, is evaluated on the NASA rotor 37 test case by steady and unsteady Reynolds Averaged Navier Stokes (RANS) simulations, using the realizable k-ε model. Flow blockage at the recirculation channel outlet was mitigated by chamfering the exit of the recirculation channel inner wall. The channel axial location from the rotor blade tip leading edge was optimized parametrically over the range −4.6% to 47.6% of the rotor tip axial chord c z . Locating the channel at 18.2% c z provided the best stall margin gain of approximately 5.5% compared to the untreated rotor. No rotor adiabatic efficiency was lost by the application of this casing treatment. The investigation into the flow structure with the recirculating channel gave a good insight into how the new casing treatment generates this benefit. The combination of stall margin gain at no rotor adiabatic efficiency loss makes this design attractive for applications to high-speed gas turbine engines.

scholarly journals Conceptual Design for Assembly in Aerospace Industry: A Method to Assess Manufacturing and Assembly Aspects of Product Architectures

2019 ◽  
Vol 1 (1) ◽  
pp. 2961-2970 ◽  
Author(s):  
Francois Bouissiere ◽  
Claude Cuiller ◽  
Pierre-Eric Dereux ◽  
Corentin Malchair ◽  
Claudio Favi ◽  
...  
Keyword(s):  
Production Rate ◽  
Conceptual Design ◽  
Process Improvement ◽  
Design Tool ◽  
Test Case ◽  
Architecture Design ◽  
Passenger Transport ◽  
Conceptual Design Phase ◽  
Civil Aircraft ◽  
Preliminary Application

AbstractIn recent years, the air transport market has quickly grown, creating new civil aircrafts demand, challenging the actual production rate of aerospace industries. The bottleneck of the current civil aircrafts production rate lies in the capability of the manufacturing and assembly facilities in relation to the aircrafts architecture design.The aim of this work is to develop a methodology and a related mathematical model that can be used at the conceptual design phase for the assessment of criticalities related to the product assemblability. The methodology allows to recognize modules and/or interfaces which are mostly affecting the assembly time providing a design tool for the comparison and evaluation of product architecture alternatives.A preliminary application has been done on the nose-fuselage of a civil aircraft for passenger transport. The test case provides interesting outcome in the identification of modules and module interfaces which are strongly affecting the assembly phase and required a re-arrangement (new architecture design) for the process improvement.

Aerodesign and Testing of an Aeromechanically Highly Loaded LP Turbine

2003 ◽  
Vol 128 (4) ◽  
pp. 643-649 ◽  
Author(s):  
F. J. Malzacher ◽  
J. Gier ◽  
F. Lippl
Keyword(s):  
High Speed ◽  
High Efficiency ◽  
Pressure Ratio ◽  
Test Facility ◽  
Performance Measurements ◽  
Two Stage ◽  
Low Pressure Turbine ◽  
High Mach ◽  
Lp Turbine ◽  
Compact Geometry

Future turbo systems for aircraft engines need very compact geometry, low weight, and high efficiency components. The geared turbofan enables the engine designer to decouple the speed of the fan and the LP turbine to combine a low speed fan with a high speed LP turbine. The low pressure turbine is a key component for this concept. The technological challenge is very much driven by the very high low-spool speed. Resulting as well from high inlet temperatures, the LP turbine needs cooling of the first stage. A new MTU LPT concept for such a high speed turbine has been developed and tested in a turbine rig. The concept consists of a two-stage turbine for extremely high speed and high stage pressure ratio (ER 2.3). This leads to extra high mechanical loading and an exotic combination of high Mach numbers (transonic) and very low Reynolds numbers. In this paper some design features are described. Some elements of the airfoil design were also tested in additional cascade tests. The two-stage turbine was tested at the Altitude Test Facility of the ILA, Stuttgart. The test setup is described including details of the instrumentation. Test data shows a good turbine performance. Measurements are also compared to 3D CFD, which is used to analyze local effects.

Application of Water-Lubricated Bearings in Motorized Centrifugal Air Compressor for Fuel Cell Automotives

2014 ◽  
Vol 670-671 ◽  
pp. 920-923 ◽  
Author(s):  
Ming Feng ◽  
Tian Ming Ren
Keyword(s):  
High Speed ◽  
Proton Exchange Membrane ◽  
High Efficiency ◽  
Load Capacity ◽  
Pressure Ratio ◽  
Pem Fuel Cells ◽  
Proton Exchange ◽  
Air Compressor ◽  
Rotating Speed ◽  
New Energy

Proton exchange membrane (PEM) fuel cells intended for new energy automotives require a high efficiency and reliability motorized compressor to supply pressurized air. This paper presents a study and development of a motorized centrifugal air compressor using water-lubricated bearings. Comparing the performance of water-lubricated bearing with gas-lubricated bearing, we found that under the same power consumption the load capacity of water-lubricated bearings are more suitable for high speed motorized compressor system. A prototype was built and tested to verify the possibility of the developed motorized centrifugal air compressor. The results show that the system can operate at a stable rotating speed up to 80,000 rpm. The flow rate of the pressurized air is 350Kg/h and pressure ratio is 1.52 at 60,000 rpm, with a global efficiency of approximately 80%.

Sign in / Sign up

Export Citation Format

Share Document