Experimental and Numerical Investigation of the Flow Field at Radial Holes in High-Speed Rotating Shafts

2012 ◽  
Author(s):  
Jan Sousek ◽  
Daniel Riedmüller ◽  
Michael Pfitzner
Keyword(s):  
Flow Field ◽  
High Speed ◽  
Discharge Coefficient ◽  
Cross Flow ◽  
Test Rig ◽  
Flow Phenomena ◽  
Rotating Shafts ◽  
Secondary Air ◽  
The One ◽  
Discharge Behaviour

Rotating and stationary orifices are used within the secondary air system to transport sealing/ cooling air to its consumers. This paper reports on measurements of the discharge coefficient of rotating radial holes as their aerodynamical behaviour is different from the one of axial or stationary holes due to the presence of centrifugal and Coriolis forces. A test rig containing two independently rotating shafts was designed to investigate the flow phenomena and the discharge behaviour of these orifices. The required air mass flow is delivered by a screw compressor and can be regulated independently to supply the inner and outer annular passages of the test rig. It allows measurements of the discharge coefficient with cross flow and co- and counter-rotating shafts with centrifugal and centripetal flow through the rotating holes. On the outer shaft, absolute and differential pressures and temperatures in the rotating frame of reference are measured via a telemetry system. Measurements of the discharge coefficient for sharp-edged and rounded shaft inserts at a variety of different flow conditions and with swirl added to the air upstream of the orifice are presented. Furthermore experiments were conducted to quantify the influence of the inner shaft (non-rotating and rotating) on the discharge behaviour of orifices in the outer shaft. To complement the data acquired from the experiments and to get a better understanding of the flow field near the rotating holes also numerical flow simulations were performed.

Experimental and Numerical Investigation of the Flow Field at Radial Holes in High-Speed Rotating Shafts

2014 ◽  
Vol 136 (8) ◽  
Author(s):  
Jan Sousek ◽  
Daniel Riedmüller ◽  
Michael Pfitzner
Keyword(s):  
Flow Field ◽  
High Speed ◽  
Discharge Coefficient ◽  
Cross Flow ◽  
Test Rig ◽  
Flow Phenomena ◽  
Rotating Shafts ◽  
Discharge Behavior ◽  
Secondary Air ◽  
Cooling Air

Rotating and stationary orifices are used within the secondary air system to transport sealing/cooling air to its consumers. This paper reports on measurements of the discharge coefficient of rotating radial holes since their aerodynamical behavior is different from that of axial or stationary holes due to the presence of centrifugal and Coriolis forces. A test rig containing two independently rotating shafts was designed in order to investigate the flow phenomena and the discharge behavior of these orifices. The required air mass flow is delivered by a screw compressor and can be independently regulated to supply the inner and outer annular passages of the test rig. It allows for measurements of the discharge coefficient with cross flow and co- and counter-rotating shafts with centrifugal and centripetal flow through the rotating holes. On the outer shaft, absolute and differential pressures and temperatures in the rotating frame of reference are measured via a telemetry system. Measurements of the discharge coefficient for sharp-edged and rounded shaft inserts at a variety of different flow conditions and with swirl added to the air upstream of the orifice are presented. Furthermore, experiments were conducted to quantify the influence of the inner shaft (nonrotating and rotating) on the discharge behavior of orifices in the outer shaft. To complement the data acquired from the experiments and to obtain a better understanding of the flow field near the rotating holes numerical flow simulations were also performed.

scholarly journals Cross-Flow Tidal Turbines with Highly Flexible Blades—Experimental Flow Field Investigations at Strong Fluid–Structure Interactions

Energies ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 797
Author(s):  
Stefan Hoerner ◽  
Iring Kösters ◽  
Laure Vignal ◽  
Olivier Cleynen ◽  
Shokoofeh Abbaszadeh ◽  
...  
Keyword(s):  
Flow Field ◽  
High Speed ◽  
Cross Flow ◽  
Speed Ratio ◽  
Fluid Structure Interactions ◽  
Dimensional Parameter ◽  
Fluid Structure ◽  
Passive Flow Control ◽  
Tidal Turbines ◽  
Tidal Turbine

Oscillating hydrofoils were installed in a water tunnel as a surrogate model for a hydrokinetic cross-flow tidal turbine, enabling the study of the effect of flexible blades on the performance of those devices with high ecological potential. The study focuses on a single tip-speed ratio (equal to 2), the key non-dimensional parameter describing the operating point, and solidity (equal to 1.5), quantifying the robustness of the turbine shape. Both parameters are standard values for cross-flow tidal turbines. Those lead to highly dynamic characteristics in the flow field dominated by dynamic stall. The flow field is investigated at the blade level using high-speed particle image velocimetry measurements. Strong fluid–structure interactions lead to significant structural deformations and highly modified flow fields. The flexibility of the blades is shown to significantly reduce the duration of the periodic stall regime; this observation is achieved through systematic comparison of the flow field, with a quantitative evaluation of the degree of chaotic changes in the wake. In this manner, the study provides insights into the mechanisms of the passive flow control achieved through blade flexibility in cross-flow turbines.

Experimental Investigation of Turbine Stage Flow Field and Performance at Varying Cavity Purge Rates and Operating Speeds

2016 ◽  
Author(s):  
Johan Dahlqvist ◽  
Jens Fridh
Keyword(s):  
Mach Number ◽  
Flow Field ◽  
High Speed ◽  
Control Volume ◽  
Spatial Average ◽  
Turbine Stage ◽  
Wide Range ◽  
Annulus Flow ◽  
Purge Flow ◽  
Secondary Air

The aspect of hub cavity purge has been investigated in a high-pressure axial low-reaction turbine stage. The cavity purge is an important part of the secondary air system, used to isolate the hot main annulus flow from cavities below the hub level. A full-scale cold-flow experimental rig featuring a rotating stage was used in the investigation, quantifying main annulus flow field impact with respect to purge flow rate as it was injected upstream of the rotor. Five operating speeds were investigated of which three with respect to purge flow, namely a high loading case, the peak efficiency, and a high speed case. At each of these operating speeds, the amount of purge flow was varied across a very wide range of ejection rates. Observing the effect of the purge rate on measurement plane averaged parameters, a minor outlet swirl decrease is seen with increasing purge flow for each of the operating speeds while the Mach number is constant. The prominent effect due to purge is seen in the efficiency, showing a similar linear sensitivity to purge for the investigated speeds. An attempt is made to predict the efficiency loss with control volume analysis and entropy production. While spatial average values of swirl and Mach number are essentially unaffected by purge injection, important spanwise variations are observed and highlighted. The secondary flow structure is strengthened in the hub region, leading to a generally increased over-turning and lowered flow velocity. Meanwhile, the added volume flow through the rotor leads to higher outlet flow velocities visible in the tip region, and an associated decreased turning. A radial efficiency distribution is utilized, showing increased impact with increasing rotor speed.

Investigation of the Prediction Correlations for the Flow Through Rotating Orifices in the Gas Turbine Secondary Air Flow System

2013 ◽  
Author(s):  
Deoras Prabhudharwadkar ◽  
Zain Dweik ◽  
A. Subramani ◽  
Murali Krishnan R.
Keyword(s):  
Gas Turbine ◽  
Discharge Coefficient ◽  
Flow System ◽  
Air Flow ◽  
Tangential Velocity ◽  
Cross Flow ◽  
Secondary System ◽  
Accurate Analysis ◽  
Secondary Air ◽  
Reliable Design

The secondary air flow system of a gas turbine cools and seals those parts of the turbine which would otherwise be exposed to the high temperatures, resulting in their life reduction or even failures. At the same time, excessive secondary air flow hinders the performance of the engine. Accurate analysis of the secondary system is therefore necessary to safeguard the reliable design of the engine and accurate life predictions. The secondary system is analyzed through the flow network analysis which comprises of chambers or cavities connected through flow passages or restrictions. There are significant number of locations where the air passes through stationary or rotating holes, e.g., the pre-swirl nozzles and the turbine blade receiver holes respectively. The accuracy of the flow prediction depends on the accuracy of the orifice discharge coefficient. This paper provides a detailed assessment of the available discharge coefficient correlations. The discharge coefficient has been found to be dependent on the geometric parameters (viz., length, inlet radius, chamfer), and the amount of cross-flow at the orifice entrance. The cross-flow may result from the relative tangential velocity between the orifice and the air or the inclination of the inlet flow with respect to the orifice axis. In this study, it was found that the discharge coefficient correlations provide similar predictions for flows without any cross-flow. However, significant deviations are seen in the predictions for the cases involving cross-flow. To identify the most accurate correlation for secondary flow application, a thorough assessment was performed using the static and the rotating test data available in the literature. In addition to the comparison using available experimental data, a CFD study was performed to independently assess the correlations. This exercise led to the identification of the most suitable correlation for our application.

Numerical Simulation of the Flow Field in a High Speed Multistage Compressor: Study of the Time Discretization Sensitivity

2015 ◽  
Author(s):  
Johannes Schreiber ◽  
Xavier Ottavy ◽  
Ghislaine Ngo Boum ◽  
Stéphane Aubert ◽  
Frédéric Sicot
Keyword(s):  
Flow Field ◽  
High Speed ◽  
State Of The Art ◽  
Axial Compressor ◽  
Time Discretization ◽  
Test Rig ◽  
Unsteady Rans ◽  
Multistage Compressor ◽  
Temporal Periodicity ◽  
Specific Contribution

The following numerical investigations are performed in the frame of a research project that aims at a better understanding of the flow unsteadiness that develops in a multistage high-speed axial compressor. First, the paper presents a new version of the 3.5 stages high-speed axial compressor CREATE (Compresseur de Recherche pour l’Etude des effets Aérodynamiques et TEchnologiques), which has been designed by Snecma and is based at the LMFA (Laboratory for Fluid Mechanics and Acoustics) on a 2MW test rig. This paper is based on numerical results obtained with 3D steady and unsteady RANS computations using the CREATE configuration. The unsteady RANS simulations are carried out over the whole spatial and temporal periodicity of the compressor. The main numerical setup has been fixed according to the state of the art. Second, the effect of three different time discretizations on the flow field in CREATE is discussed. The global performance of the compressor is not significantly affected. However the change in the time discretization impacts the structure of the flow at specific locations. The main focus of this study lies on the transport of flow structures and the analysis of their interactions. A double modal decomposition method, which highlights the specific contribution of the interactions on the overall flow field, is applied for the study of the highly complex and unsteady flow field. It allows identifying which interactions are more sensitive to the change in the time discretization.

Experimental Study on Pressure Losses in Circular Orifices With Inlet Cross Flow

2018 ◽  
Vol 140 (7) ◽  
Author(s):  
Daniel Feseker ◽  
Mats Kinell ◽  
Matthias Neef
Keyword(s):  
Experimental Study ◽  
Film Cooling ◽  
Gas Turbines ◽  
Discharge Coefficient ◽  
Pressure Ratio ◽  
Cross Flow ◽  
Pressure Losses ◽  
Wide Range ◽  
Cooling Hole ◽  
Secondary Air

The ability to understand and predict the pressure losses of orifices is important in order to improve the air flow within the secondary air system. This experimental study investigates the behavior of the discharge coefficient for circular orifices with inlet cross flow which is a common flow case in gas turbines. Examples of this are at the inlet of a film cooling hole or the feeding of air to a blade through an orifice in a rotor disk. Measurements were conducted for a total number of 38 orifices, covering a wide range of length-to-diameter ratios, including short and long orifices with varying inlet geometries. Up to five different chamfer-to-diameter and radius-to-diameter ratios were tested per orifice length. Furthermore, the static pressure ratio across the orifice was varied between 1.05 and 1.6 for all examined orifices. The results of this comprehensive investigation demonstrate the beneficial influence of rounded inlet geometries and the ability to decrease pressure losses, which is especially true for higher cross flow ratios where the reduction of the pressure loss in comparison to sharp-edged holes can be as high as 54%. With some exceptions, the chamfered orifices show a similar behavior as the rounded ones but with generally lower discharge coefficients. Nevertheless, a chamfered inlet yields lower pressure losses than a sharp-edged inlet. The obtained experimental data were used to develop two correlations for the discharge coefficient as a function of geometrical as well as flow properties.

Directed Particle-Laden Micro-Jet for Dental Caries Evacuation (Keynote Paper)

2003 ◽  
Author(s):  
Michael Amitay ◽  
Shayne Kondor ◽  
Scott Herdic ◽  
Steven L. Anderson
Keyword(s):  
Dental Caries ◽  
Flow Field ◽  
Active Control ◽  
High Speed ◽  
Cross Flow ◽  
Jet Flow ◽  
Spreading Rate ◽  
Exit Plane ◽  
Keynote Paper ◽  
The Cross

Active and passive approaches to control the velocity and concentration of a high speed round particle-laden jet are investigated experimentally using a stereo PIV system. Active control of the flow field and the particles’ velocity and concentration fields, via the addition of swirl to the carrier jet, has shown to have a significant effect in altering both phases. Control is also affected by placing passive pins at the jet exit plane, which results in alteration of the velocity in planes across and normal to the pins. Furthermore, the mixing is increased and the spreading rate is modified. Depending on the number of pins used and their azimuthal location, their interaction with the carrier jet flow lead to the modification of the cross-flow shape of the jet and the direction of the flow.

Design of a High-Speed Rotating Test Rig for Adaptive Seal Systems

2015 ◽  
Author(s):  
Laura S. Beermann ◽  
Corina Höfler ◽  
Hans-Jörg Bauer
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
High Speed ◽  
Operating Conditions ◽  
Turbine Engines ◽  
Parameter Study ◽  
Test Rig ◽  
Swirl Chamber ◽  
Mass Flows ◽  
Gap Width

Gas turbine engines are subject to increased performance and improved efficiency, which leads to rising core temperatures with additional cooling needs. Reducing the parasitic leakage in the secondary flow system is important to meet the challenging requirements. New seal designs have to be tested and optimized at engine like conditions, like high pressure of up to 9 bar and surface speed of up to 280 m/s as well as an adjusted flow field. Flexible seal designs are an innovative approach to reduce leakage mass flows significantly. Axial and radial movements during transient operating conditions can be compensated easily, thus allowing a smaller gap width and minimizing rub and heat load. This paper describes the design and construction of a new rotating test rig facility. To the knowledge of the authors, this is the only test rig with an adjustable gap width and flow field in a high pressure and speed range. The facility is capable of up to 8 bar differential pressure across the seal and up to 4 bar back pressure. The high revolution engine facilitates a surface speed of up to 280 m/s. A traversable casing allows a quick change of the gap width during operation and simulates radial and axial rotor/stator movements in the engine. The seal movement as well as the resulting gap width are measured during operation to fully understand the seal behavior. An important feature of the new test rig is the continuously adjustable pre-swirl system. It has been designed to cover the different flow conditions in the real engine. Therefore, a RANS parameter study of the pre-swirl chamber has been conducted, which shows the adjustability of different pre-swirl ratios for constant and changing inlet mass flows.

Increasing Flashback Resistance in Lean Premixed Swirl-Stabilized Hydrogen Combustion by Axial Air Injection

2014 ◽  
Author(s):  
Thoralf G. Reichel ◽  
Steffen Terhaar ◽  
Oliver Paschereit
Keyword(s):  
Flow Field ◽  
Gas Turbines ◽  
High Speed ◽  
Flame Temperature ◽  
Air Injection ◽  
Reacting Flow ◽  
Nox Emissions ◽  
Test Rig ◽  
Swirl Number ◽  
Lean Premixed

Since lean premixed combustion allows for fuel-efficiency and low emissions, it is nowadays state of the art in stationary gas turbines. In the long term, it is also a promising approach for aero engines, when safety issues like lean blowout (LBO) and flame flashback in the premixer can be overcome. While for the use of hydrogen the LBO limits are extended, the flashback propensity is increased. Thus, axial air injection is applied in order to eliminate flashback in a swirl-stabilized combustor burning premixed hydrogen. Axial injection constitutes a non-swirling jet on the central axis of the radial swirl generator which influences the vortex breakdown position. In the present work changes in the flow field and their impact on flashback limits of a model combustor are evaluated. First, a parametric study is conducted under isothermal test conditions in a water tunnel employing particle image velocimetry (PIV). The varied parameters are the amount of axially injected air and swirl number. Subsequently, flashback safety is evaluated in the presence of axial air injection in an atmospheric combustor test rig and a stability map is recorded. The flame structure is measured using high-speed OH* chemiluminescence imaging. Simultaneous high-speed PIV measurements of the reacting flow provide insight in the time-resolved reacting flow field and indicate the flame location by evaluating the Mie scattering of the raw PIV images by the means of the Qualitative Light Sheet (QLS) technique. The isothermal tests identify the potential of axial air injection to overcome the axial velocity deficits at the nozzle outlet, which is considered crucial in order to provide flashback safety. This effect of axial air injection is shown to prevail in the presence of a flame. Generally, flashback safety is shown to benefit from an elevated amount of axial air injection and a lower swirl number. Note, that the latter also leads to increased NOx emissions, while axial air injection does not. Additionally, fuel momentum is indicated to positively influence flashback resistance, although based on a different mechanism, an explanation of which is suggested. In summary, flashback-proof operation of the burner with a high amount of axial air injection is achieved on the whole operating range of the test rig at inlet temperatures of 620 K and up to stoichiometric conditions while maintaining single digit NOx emissions below a flame temperature of 2000 K.

A Comprehensive Investigation of Preswirled Flow Through Rotating Radial Holes

2014 ◽  
Vol 137 (3) ◽  
Author(s):  
Daniel Riedmüller ◽  
Jan Sousek ◽  
Michael Pfitzner
Keyword(s):  
Experimental Data ◽  
Gas Turbines ◽  
Discharge Coefficient ◽  
Cfd Simulation ◽  
Test Rig ◽  
Outer Annulus ◽  
Flow Phenomena ◽  
Flow Through ◽  
Flow Directions ◽  
Experimental Findings

This paper reports on the flow (centrifugal = radially outward, centripetal = radially inward) through rotating radial orifices with and without preswirl in the flow approaching the orifice in the outer annulus. The aerodynamical behavior of flow through radial rotating holes is different from the one through axial and stationary holes due to the presence of centrifugal and Coriolis forces. To investigate the flow phenomena and the discharge coefficient of these orifices in detail, an existing test rig containing two independently rotating shafts (corotating and counter rotating) was used. To simulate conditions of real gas turbines, where the flow is often influenced by upstream components, various preswirl angles were used in the test rig. Measurements of the flow discharge coefficient in both flow directions through the orifices (centripetal and centrifugal), with and without preswirl generation in the outer annulus, are presented at various flow conditions (pressure ratios across orifices, Mach numbers of approaching flow) and for different geometric parameters (length to diameter ratios, sharp/rounded inlet edges). Flow effects that occur with preswirled flow are clarified. A comparison of the experimental data, for both flow directions, shows a similar behavior of the discharge coefficients with increasing shaft speeds. To supplement the experimental data and to better understand the experimental findings, numerical simulations were performed, which show a good agreement with the experimental results. Furthermore, an optimization model with complete automatic grid generation, computational fluid dynamics (CFD) simulation, and postprocessing, was built to enable large parametric studies, e.g., grid independence of the solutions.

Sign in / Sign up

Export Citation Format

Share Document