Effects of Axial Row-Spacing for Double-Jet Film-Cooling on the Cooling Effectiveness

2011 ◽  
Author(s):  
Zhan Wang ◽  
Jian-Jun Liu ◽  
Bai-tao An ◽  
Chao Zhang
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Inlet Guide Vane ◽  
Row Spacing ◽  
Suction Surface ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Pressure Surface ◽  
Cylindrical Holes ◽  
Compound Angle

The effects of axial row-spacing for double jet film-cooling (DJFC) with compound angle on the cooling characteristics under different blowing ratios were investigated numerically. First, the flow fields and cooling effectiveness of DJFC on flat plate with different axial row-spacing were calculated. Film-cooling with fan-shaped or cylindrical holes was also calculated for the comparison. The results indicate that a larger axial row-spacing is helpful to form the anti-kidney vortex and to improve the cooling effectiveness. The DJFC was then applied to the suction and pressure surface of a real turbine inlet guide vane. Comparisons of film-cooling effectiveness with the cylindrical and fan-shaped holes were also conducted. The results for the guide vane show that on the suction surface the DJFC with a larger axial row-spacing leads to better film coverage and better film-cooling effectiveness than the cylindrical or fan-shaped holes. On the pressure surface, however, the film-cooling with fan-shaped holes is superior to the others.

Experimental Study of Full Coverage Film Cooling Effectiveness for a Turbine Blade With Compound Shaped Holes

2020 ◽  
Author(s):  
Shuai-qi Zhang ◽  
Cun-liang Liu ◽  
Qi-ling Guo ◽  
Da-peng Liang ◽  
Fan Zhang
Keyword(s):  
Turbine Blade ◽  
Turbulence Intensity ◽  
Mass Flux ◽  
Film Cooling ◽  
Flux Ratio ◽  
Suction Surface ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Pressure Surface ◽  
Cylindrical Holes

Abstract The film coverage of a turbine blade surface is determined by all the film cooling structures. The direct study of full coverage film cooling is relatively rare, especially for related research on turbine blades. In this paper, the pressure-sensitive paint (PSP) measurement technique is used to carry out experiments under different turbulence intensities and mass flux ratios, and the distribution of the film cooling effectiveness on the entire surface is studied in detail. In this study, a basic turbine blade and an improved turbine blade are investigated. The film cooling hole position distribution on the improved blade is the same as that on the basic blade, but the film cooling hole shape on the suction surface and the pressure surface is changed from cylindrical holes to laid-back fan-shaped holes. Both blades have 5 rows of cylindrical holes at the leading edge and 4 rows of film cooling holes on the suction surface and the pressure surface. The leading edge, suction surface, and pressure surface have their own coolant inlet cavities. This kind of design is not only close to the actual working conditions in a flow distribution but also conveniently eliminates the mutual interference caused by the uneven flow distribution between the pressure surface and the suction surface to facilitate the independent analysis of the pressure surface and the suction surface. In this paper, the film cooling effectiveness of two kinds of turbine blades under different turbulence intensities and mass flux ratios is studied. The results show that the average cooling effectiveness of the improved blade is much better than that of the basic blade. The laid-back fan-shaped hole rows improve the cooling effectiveness of the suction surface by 60% to 100% and 50% to 120% on the pressure surface. The increase in turbulence intensity will reduce the cooling effectiveness of the blade surface; however, the effect of the turbulence intensity becomes weaker with an increase in the mass flux ratio. Compared with the multiple rows of cylindrical holes, the cooling effectiveness of the laid-back fan-shaped holes is more affected by the turbulence intensity under the small mass flux ratio.

Film Cooling Performance of Tripod Antivortex Injection Holes Over the Pressure and Suction Surfaces of a Nozzle Guide Vane

2017 ◽  
Vol 9 (2) ◽  
Author(s):  
Sridharan Ramesh ◽  
Christopher LeBlanc ◽  
Diganta Narzary ◽  
Srinath Ekkad ◽  
Mary Anne Alvin
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Density Ratio ◽  
Leading Edge ◽  
Suction Surface ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Pressure Surface ◽  
Nozzle Guide

Film cooling performance of the antivortex (AV) hole has been well documented for a flat plate. The goal of this study is to evaluate the same over an airfoil at three different locations: leading edge suction and pressure surface and midchord suction surface. The airfoil is a scaled up first stage vane from GE E3 engine and is mounted on a low-speed linear cascade wind tunnel. Steady-state infrared (IR) technique was employed to measure the adiabatic film cooling effectiveness. The study has been divided into two parts: the initial part focuses on the performance of the antivortex tripod hole compared to the cylindrical (CY) hole on the leading edge. Effects of blowing ratio (BR) and density ratio (DR) on the performance of cooling holes are studied here. Results show that the tripod hole clearly provides higher film cooling effectiveness than the baseline cylindrical hole case with overall reduced coolant usage on the both pressure and suction sides of the airfoil. The second part of the study focuses on evaluating the performance on the midchord suction surface. While the hole designs studied in the first part were retained as baseline cases, two additional geometries were also tested. These include cylindrical and tripod holes with shaped (SH) exits. Film cooling effectiveness was found at four different blowing ratios. Results show that the tripod holes with and without shaped exits provide much higher film effectiveness than cylindrical and slightly higher effectiveness than shaped exit holes using 50% lesser cooling air while operating at the same blowing ratios. Effectiveness values up to 0.2–0.25 are seen 40-hole diameters downstream for the tripod hole configurations, thus providing cooling in the important trailing edge portion of the airfoil.

Influence of Coolant Density on Turbine Platform Film-Cooling With Stator–Rotor Purge Flow and Compound-Angle Holes

2014 ◽  
Vol 6 (4) ◽  
Author(s):  
Kevin Liu ◽  
Shang-Feng Yang ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Fundamental Parameters ◽  
Blowing Ratio ◽  
Purge Flow ◽  
Cylindrical Holes ◽  
Exit Mach Number ◽  
Compound Angle

A detailed parametric study of film-cooling effectiveness was carried out on a turbine blade platform. The platform was cooled by purge flow from a simulated stator–rotor seal combined with discrete hole film-cooling. The cylindrical holes and laidback fan-shaped holes were accessed in terms of film-cooling effectiveness. This paper focuses on the effect of coolant-to-mainstream density ratio on platform film-cooling (DR = 1 to 2). Other fundamental parameters were also examined in this study—a fixed purge flow of 0.5%, three discrete-hole film-cooling blowing ratios between 1.0 and 2.0, and two freestream turbulence intensities of 4.2% and 10.5%. Experiments were done in a five-blade linear cascade with inlet and exit Mach number of 0.27 and 0.44, respectively. Reynolds number of the mainstream flow was 750,000 and was based on the exit velocity and chord length of the blade. The measurement technique adopted was the conduction-free pressure sensitive paint (PSP) technique. Results indicated that with the same density ratio, shaped holes present higher film-cooling effectiveness and wider film coverage than the cylindrical holes, particularly at higher blowing ratios. The optimum blowing ratio of 1.5 exists for the cylindrical holes, whereas the effectiveness for the shaped holes increases with an increase of blowing ratio. Results also indicate that the platform film-cooling effectiveness increases with density ratio but decreases with turbulence intensity.

Effect of Density Ratio on Film-Cooling Effectiveness Distribution and Its Uniformity for Several Hole Geometries on a Flat Plate

2019 ◽  
Vol 141 (5) ◽  
Author(s):  
Jiaxu Yao ◽  
Jin Xu ◽  
Ke Zhang ◽  
Jiang Lei ◽  
Lesley M. Wright
Keyword(s):  
Flat Plate ◽  
Film Cooling ◽  
Density Ratio ◽  
Lateral Spread ◽  
Spanwise Direction ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cylindrical Holes ◽  
Density Ratios ◽  
Compound Angle

The film cooling effectiveness distribution and its uniformity downstream of a row of film cooling holes on a flat plate are investigated by pressure sensitive paint (PSP) under different density ratios. Several hole geometries are studied, including streamwise cylindrical holes, compound-angled cylindrical holes, streamwise fan-shape holes, compound-angled fan-shape holes, and double-jet film-cooling (DJFC) holes. All of them have an inclination angle (θ) of 35 deg. The compound angle (β) is 45 deg. The fan-shape holes have a 10 deg expansion in the spanwise direction. For a fair comparison, the pitch is kept as 4d for the cylindrical and the fan-shape holes, and 8d for the DJFC holes. The uniformity of effectiveness distribution is described by a new parameter (Lateral-Uniformity, LU) defined in this paper. The effects of density ratios (DR = 1.0, 1.5 and 2.5) on the film-cooling effectiveness and its uniformity are focused. Differences among geometries and effects of blowing ratios (M = 0.5, 1.0, 1.5, and 2.0) are also considered. The results show that at higher density ratios, the lateral spread of the discrete-hole geometries (i.e., the cylindrical and the fan-shape holes) is enhanced, while the DJFC holes is more advantageous in film-cooling effectiveness. Mostly, a higher lateral-uniformity is obtained at DR = 2.5 due to better coolant coverage and enhanced lateral spread, but the effects of the density ratio on the lateral-uniformity are not monotonic in some cases. Utilizing the compound angle configuration leads to an increased lateral-uniformity due to a stronger spanwise motion of the jet. Generally, with a higher blowing ratio, the lateral-uniformity of the discrete-hole geometries decreases due to narrower traces, while that of the DJFC holes increases due to a stronger spanwise movement.

Film-Cooling on a Gas Turbine Blade Pressure Side or Suction Side With Compound Angle Shaped Holes

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
Zhihong Gao ◽  
Diganta P. Narzary ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Suction Side ◽  
Pressure Side ◽  
Blade Surface ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Pressure Surface ◽  
Compound Angle

The film-cooling effectiveness on the surface of a high pressure turbine blade is measured using the pressure sensitive paint technique. Compound angle laidback fan-shaped holes are used to cool the blade surface with four rows on the pressure side and two rows on the suction side. The coolant injects to one side of the blade, either pressure side or suction side. The presence of wake due to the upstream vanes is simulated by placing a periodic set of rods upstream of the test blade. The wake rods can be clocked by changing their stationary positions to simulate progressing wakes. The effect of wakes is recorded at four phase locations along the pitchwise direction. The freestream Reynolds number, based on the axial chord length and the exit velocity, is 750,000. The inlet and exit Mach numbers are 0.27 and 0.44, respectively, resulting in a pressure ratio of 1.14. Five average blowing ratios ranging from 0.4 to 1.5 are tested. Results reveal that the tip-leakage vortices and endwall vortices sweep the coolant on the suction side to the midspan region. The compound angle laidback fan-shaped holes produce a good film coverage on the suction side except for the regions affected by the secondary vortices. Due to the concave surface, the coolant trace is short and the effectiveness level is low on the pressure surface. However, the pressure side acquires a relatively uniform film coverage with the multiple rows of cooling holes. The film-cooling effectiveness increases with the increasing average blowing ratio for either side of coolant ejection. The presence of stationary upstream wake results in lower film-cooling effectiveness on the blade surface. The compound angle shaped holes outperform the compound angle cylindrical holes by the elevated film-cooling effectiveness, particularly at higher blowing ratios.

scholarly journals Film Cooling on a Gas Turbine Rotor Blade

1991 ◽  
Author(s):  
Kenichiro Takeishi ◽  
Sunao Aoki ◽  
Tomohiko Sato ◽  
Keizo Tsukagoshi
Keyword(s):  
Mass Transfer ◽  
Film Cooling ◽  
Rotor Blade ◽  
Turbine Rotor ◽  
Suction Surface ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Turbine Rotor Blade ◽  
Pressure Surface ◽  
Rotating Blade

The film cooling effectiveness on a low-speed stationary cascade and the rotating blade has been measured by using a heat-mass transfer analogy. The film cooling effectiveness on the suction surface of the rotating blade fits well with that on the stationary blade, but a low level of effectiveness appears on the pressure surface of the rotating blade. In this paper, typical film cooling data will be presented and film cooling on a rotating blade is discussed.

scholarly journals Numerical Investigation of Single-Row Double-Jet Film Cooling of a Turbine Guide Vane under High-Temperature and High-Pressure Conditions

Energies ◽  
2022 ◽  
Vol 15 (1) ◽  
pp. 287
Author(s):  
Jin Hang ◽  
Jingzhou Zhang ◽  
Chunhua Wang ◽  
Yong Shan
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Suction Surface ◽  
Positive Potential ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Injection Angle ◽  
Jet In Crossflow ◽  
Cooling Enhancement ◽  
Turbine Guide Vane

Single-row double-jet film cooling (DJFC) of a turbine guide vane is numerically investigated in the present study, under a realistic aero-thermal condition. The double-jet units are positioned at specific locations, with 57% axial chord length (Cx) on the suction side or 28% Cx on the pressure side with respect to the leading edge of the guide vane. Three spanwise spacings (Z) in double-jet unit (Z = 0, 0.5d, and 1.0d, here d is the film hole diameter) and four spanwise injection angles (β = 11°, 17°, 23°, and 29°) are considered in the layout design of double jets. The results show that the layout of double jets affects the coupling of adjacent jets and thus subsequently changes the jet-in-crossflow dynamics. Relative to the spanwise injection angle, the spanwise spacing in a double-jet unit is a more important geometric parameter that affects the jet-in-crossflow dynamics in the downstream flowfield. With the increase in the spanwise injection angle and spanwise spacing in the double-jet unit, the film cooling effectiveness is generally improved. On the suction surface, DJFC does not show any benefit on film cooling improvement under smaller blowing ratios. Only under larger blowing ratios does its positive potential for film cooling enhancement start to show. Compared to the suction surface, the positive potential of the DJFC on enhancing film cooling effectiveness behaves more obviously on the pressure surface. In particular, under large blowing ratios, the DJFC plays dual roles in suppressing jet detachment and broadening the coolant jet spread in a spanwise direction. With regard to the DJFC on the suction surface, its main role in film cooling enhancement relies on the improvement of the spanwise film layer coverage on the film-cooled surface.

Experimental Investigation of Turbine Phantom Cooling on Endwall With Trailing Edge Discharge Flow

2014 ◽  
Author(s):  
Yang Zhang ◽  
Xin Yuan
Keyword(s):  
Secondary Flow ◽  
Film Cooling ◽  
Guide Vane ◽  
Scale Up ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Discharge Flow ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Compound Angle

The film cooling ejection on High Pressure (Hp) turbine component surface is strongly affected by the complex flow structure in the nozzle guide vane or rotor blade passages. The action of secondary flow in the main passage could dominate the film cooling effectiveness distribution on the component surfaces. The film cooling ejections from endwall and airfoil trailing edge are mixed by the secondary flow. Considering a small part of the coolant ejection from trailing edge discharge flow will move from the airfoil trailing edge pressure side to endwall downstream and then cover some area, the interaction between the coolants injected from endwall and airfoil trailing edge is worth investigating. Though the temperature of coolant discharge flow from trailing edge increases after the mixing process in the internal cooling procedure, the ejections moving from airfoil to endwall still have the potential of second order cooling. This part of the coolant is called “Phantom cooling flow” in the paper. A typical scale-up model of Hp turbine NGV is used in the experiment to investigate the cooling performance of ejection from trailing edge. Instead of the airfoil trailing edge platform itself, the film cooling effectiveness is measured on the downstream part of the endwall. This paper is focused on the trailing edge discharge flow with compound angle effects and the coolant from discharge holes moving from trailing edge to endwall surface. The coolant flow is injected from the straight discharge holes with a compound angle of 15deg and 45deg respectively. The film cooling holes on the endwall are used simultaneously to investigate the combined effects. The blowing ratio and different configurations of compound angle holes are selected to be the changing parameters in the paper. The experiment is completed with the blowing ratio changing from M = 0.7 to M = 1.3 and the compound angle is introduced to the entire row of trailing edge discharge holes (full span), with inlet Reynolds numbers of Re = 3.5×105 and an inlet Mach number of Ma = 0.1.

Enhancement of Film Cooling Effectiveness Using Backward Injection Holes

2015 ◽  
Author(s):  
Sehjin Park ◽  
Eui Yeop Jung ◽  
Seon Ho Kim ◽  
Ho-Seong Sohn ◽  
Hyung Hee Cho
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Row Spacing ◽  
Pressure Sensitive Paint ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Pressure Sensitive ◽  
Cooling Method ◽  
Cylindrical Holes

Film cooling is a cooling method used to protect the hot components of a gas turbine from high temperature conditions. For this purpose, high and uniform film cooling effectiveness is required to protect the vanes/blades from excessive thermal stress. Backward injection is proposed as one of the methods for the improvement of film cooling effectiveness. In this study, experiments were performed to investigate the effect of backward injection on film cooling effectiveness, using pressure sensitive paint (PSP) method. Four experimental configurations were composed of forward and backward injection cylindrical holes. The cylindrical holes were aligned in two staggered rows with pitch (p) of 6d and row spacing (s) of 3d. The injection angles (α) of the cylindrical holes were 35° and 145° for forward and backward injection, respectively. The blowing ratios (M) ranged from 0.5 to 2.0 and the density ratio (DR) was about 1. The results indicate that backward injection enhanced not only film cooling effectiveness but also the lateral cooling uniformity. At a high blowing ratio, all configurations demonstrated higher film cooling effectiveness with backward injection than with only forward injection; thus, the dispersion of the backward injection jets enhanced the lateral coverage over wide areas. Configuration, in particular, arranged with forward injection in the first row and backward injection in the second row, obtained the highest film cooling effectiveness among the four cases studied, due to the dispersion of the backward injection jets and the coolant supply from the forward injection jets at a high blowing ratio.

Experimental and Numerical Film Effectiveness Downstream a Row of Compound Angle Film Holes

2003 ◽  
Author(s):  
A. Khanicheh ◽  
M. E. Taslim
Keyword(s):  
High Temperature ◽  
Film Cooling ◽  
Computational Study ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Single Row ◽  
Cooling Hole ◽  
Cylindrical Holes ◽  
Film Cooling Holes ◽  
Compound Angle

High component lifetimes of modern gas turbines can be achieved by cooling the airfoils effectively. Film cooling is commonly employed on the airfoils and other engine hot section surfaces in order to protect them from the high thermal stress fields created by exposure to combustion gases. Complex geometries as well as optimized cooling considerations often dictate the use of compound-angled film cooling hole. In the present experimental and computational study, the effects that two different compound angle film cooling hole injection configurations have on film cooling effectiveness are investigated. Film cooling effectiveness measurements have been made downstream of a single row of compound angle cylindrical holes with a diameter of 7.5 mm, and a single row of compound angle, diffuser-shaped holes with an inlet diameter of 7.5 mm. The cylindrical holes were inclined (α=25°) with respect to the coverage surface and were oriented perpendicular to the high-temperature airflow direction. The diffuser-shaped holes had a compound angle of 45 degrees with respect to the high temperature air flow direction and, similar to the cylindrical film holes, a 25-deg angle with the coverage surface. Both geometries were tested over a blowing ratio range of 0.7 to 4.0. Surface temperatures were measured along four longitudinal rows of thermocouples covering the downstream area between two adjacent holes. The results showed that the best overall protection over the widest range of blowing ratios was provided by the diffuser-shaped film cooling holes. Compared with the cylindrical hole results, the diffuser-shaped expansion holes produced higher film cooling effectiveness downstream of the film cooling holes, particularly at high blowing ratios. The increased cross sectional area at the shaped hole exit compared to that of the cylindrical hole lead to a reduction of the mean velocity, thus the reduction of the momentum flux of the jet exiting the hole. Therefore, the penetration of the jet into the main flow was reduced, resulting in an increased cooling effectiveness. A commercially available CFD software package was used to study film cooling effectiveness downstream of the row of holes. Comparisons between the experimentally measured and numerically calculated film effectiveness distributions showed that the computed results are in reasonable agreement with the measured results. Therefore, CFD can be considered as a viable tool to predict the cooling performance of different film cooling configurations in a parametric study. A more realistic turbulence model, possibly adopting a two-layer model that incorporates boundary layer anisotropy, in the computational study may improve the predicted results.

Sign in / Sign up

Export Citation Format

Share Document