Thermodynamic Evaluation of Humidified Air Turbine (HAT) Cycles

2004 ◽  
Author(s):  
R. Yadav ◽  
Pawan Krishan Dwivedi ◽  
Pradeep Kumar ◽  
Samir Saraswati
Keyword(s):  
Pressure Ratio ◽  
Plant Performance ◽  
Optimum Operating ◽  
Operating Parameters ◽  
Thermodynamic Evaluation ◽  
Predicting Performance ◽  
Air Turbine ◽  
Plant Optimization ◽  
The One ◽  
Humidified Air

The present work deals with the parametric energy analysis of humidified air turbine (HAT) cycles, identifying the best plant arrangement and predicting the influence of operating parameters on plant performance. In predicting performance plant optimization is to be achieved for an overall pressure ratio. The results presented will be helpful to designers to select the best configurations and optimum operating parameters. The best configuration among the chosen configurations is the one in which there are three intercoolers and two aftercoolers.

Effect of Different Geometrical Inlet Pipes on a High Speed Centrifugal Compressor

2013 ◽  
Author(s):  
Ce Yang ◽  
Ben Zhao ◽  
C. C. Ma ◽  
Dazhong Lao ◽  
Mi Zhou
Keyword(s):  
Centrifugal Compressor ◽  
High Speed ◽  
Pressure Ratio ◽  
Inlet Pipe ◽  
Unsteady Pressure ◽  
Bent Pipe ◽  
Low Mass ◽  
Compressor Performance ◽  
Spectral Frequency ◽  
The One

Two different inlet configurations, including a straight pipe and a bent pipe, were experimentally tested and numerically simulated using a high-speed, low-mass flow centrifugal compressor. The pressure ratios of the compressor with the two inlet configurations were tested and then compared to illustrate the effect of the bent inlet pipe on the compressor. Furthermore, different circumferential positions of the bent inlet pipe relative to the volute are discussed for two purposes. One purpose is to describe the changes in the compressor performance that result from altering the circumferential position of the bent inlet pipe relative to the volute. This change in performance may be the so-called clocking effect, and its mechanism is different from the one in multistage turbomachinery. The other purpose is to investigate the unsteady flow for different matching states of the bent inlet pipe and volute. Thus, the frequency spectrum of unsteady pressure fluctuation was applied to analyze the aerodynamic response. Compared with the straight inlet pipe, the experimental results show that the pressure ratio is modulated and that the choke point is shifted in the bent inlet pipe. Similarly, the pressure ratio can be influenced by altering the circumferential position of the bent inlet pipe relative to the volute, which may have an effect on the unsteady pressure in the rotor section. Therefore, the magnitude of interest spectral frequency is significantly changed by clocking the bent inlet pipe.

A Small Gas Turbine Plant for Cogeneration of Electricity, Thermal and Cooling Thermal Energy With an Absorption Unit

1997 ◽  
Author(s):  
Maurizio De Lucia ◽  
Carlo Lanfranchi ◽  
Antonio Matucci
Keyword(s):  
Gas Turbine ◽  
Thermal Energy ◽  
Operating Conditions ◽  
Hot Water ◽  
Plant Performance ◽  
Cooling Power ◽  
Operating Parameters ◽  
The European Union ◽  
Cogeneration Plant ◽  
Two Stage

A cogeneration plant with a small gas turbine was installed in a pharmaceutical factory and instrumented for acquiring all the values necessary to appraise both its energetic and cost advantages. The plant was designed and built as a demonstrative project under a program for energy use improvement in industry, partially financed by the European Union. The system comprises as its main components: 1) a gas turbine cogeneration plant for production of power and thermal energy under the form of hot water, superheated water, and steam; 2) a two-stage absorption unit, fueled by the steam produced in the cogeneration plant, for production of cooling thermal energy. The plant was provided with an automatized control system for the acquisition of plant operating parameters. The large amount of data thus provided made it possible to compare the new plant, under actual operating conditions, with the previously existing cooling power station with compression units, and with a traditional power plant. This comparative analysis was based on measurements of the plant operating parameters over nine months, and made it possible to compare actual plant performance with that expected and ISO values. The analysis results reveal that gas turbine performance is greatly affected by part-load as well as ambient temperature conditions. Two-stage absorber performance, moreover, turned out to decrease sharply and more than expected in off-design operating conditions.

The treatment of zinc-cyanide electroplating rinse water using an electrocoagulation process

2013 ◽  
Vol 68 (10) ◽  
pp. 2220-2227 ◽  
Author(s):  
Elif Senturk
Keyword(s):  
Electrode Material ◽  
Operating Time ◽  
Operating Conditions ◽  
Optimum Operating ◽  
Operating Parameters ◽  
Initial Ph ◽  
Electrocoagulation Process ◽  
Removal Efficiencies ◽  
Rinse Water ◽  
Electrode Connection

This paper investigates the treatment of zinc-cyanide electroplating rinse water using an electrocoagulation process (ECP). The effects of operating parameters such as electrode material, current density (2.5–40 A/m2), operating time (0–60 min), initial pH (5–12) and electrode connection mode (monopolar parallel (MP-P), monopolar series and bipolar series) on the ECP were evaluated to find the optimum operating conditions. At 20 A/m2, 60 min, the highest removal efficiencies were obtained with 85 and 99% for Fe and 64 and 33% for Al electrodes, for cyanide and zinc, respectively. The optimum operating conditions were found to be 30 A/m2 and 40 min, for the Fe electrode at the original pH (9.5) of the rinse water. Considering efficiency and economy, the MP-P connection mode was determined as the optimum connection mode.

Progress of the 40 MW-Class Advanced Humid Air Turbine Tests

2013 ◽  
Vol 135 (11) ◽  
Author(s):  
Manabu Yagi ◽  
Hidefumi Araki ◽  
Hisato Tagawa ◽  
Tomomi Koganezawa ◽  
Chihiro Myoren ◽  
...  
Keyword(s):  
Metal Surface ◽  
Control Method ◽  
Cooling System ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Test Facility ◽  
Humid Air ◽  
Air Turbine ◽  
Calculation Results ◽  
Flow Compressor

A 40 MW-class test facility has been constructed to verify practicability of applying the advanced humid air turbine (AHAT) system to a heavy-duty gas turbine. Verification tests have been carried out from January 2012, and interaction effects between the key components were established. First, water atomization cooling (WAC) was confirmed to contribute to both increased mass flow rate and pressure ratio for the axial-flow compressor. The good agreement between measured and calculated temperatures at the compressor discharge was also confirmed. These results demonstrated the accuracy of the developed prediction model for the WAC. Second, a control method that realized both flame stability and low nitrogen oxides (NOx) emissions was verified. Although the power output and air humidity were lower than the rated values, NOx concentration was about 10 ppm. Finally, a hybrid nozzle cooling system, which utilized both compressor discharged air and humid air, was developed and tested. The metal surface temperatures of the first stage nozzles were measured, and they were kept under the permissible metal temperature. The measured temperatures on the metal surface reasonably corresponded with calculation results.

Air Characteristics in Air Turbine Spindle of Ultra Precision Machines

2010 ◽  
Vol 297-301 ◽  
pp. 396-401
Author(s):  
Mehrdad Vahdati ◽  
E. Azimi ◽  
Ali Shokuhfar
Keyword(s):  
High Speed ◽  
Design Procedure ◽  
Inlet Pressure ◽  
Cylindrical Shape ◽  
Air Inlet ◽  
Wind Turbine System ◽  
Air Turbine ◽  
Ultra Precision ◽  
The One ◽  
Precision Machines

Air Spindles have been used in ultra precision machines for several years due to their advantages such as high speed rotation, low friction, and low vibration, [1]. Air spindles are widely used in these machines for producing precise work pieces. Although, spindles function on a very complicated theoretical basis, [2, 3], their structure is very simple and consists of mainly a rotor and a stator. The rotor/stator could be made of different shapes. A cylindrical shape is the one commonly in use. The spindle designed in this work has a spherical configuration. It has been designed so that it could be moved without application of electric motor and only by a wind turbine system, [4]. The spindle studied in this research uses compressed air for rotor suspension, and has an air turbine for rotating its shaft. A thin air film acts as bearing layer between rotor and stator. In design procedure, operation parameters such as air inlet pressure for turbine, air inlet pressure for bearing, diameter of turbine nuzzles, diameter of bearing nuzzles, clearance between rotor and stator and etc. have been considered, [5]. A prototype spindle has been manufactured using design criteria. The influence of above mentioned parameters have been recognized through experiments.

Design Study of a Humidification Tower for the Advanced Humid Air Turbine System

2005 ◽  
Author(s):  
Hidefumi Araki ◽  
Shinichi Higuchi ◽  
Shinya Marushima ◽  
Shigeo Hatamiya
Keyword(s):  
Gas Turbine ◽  
Heat Exchangers ◽  
High Efficiency ◽  
Cooling System ◽  
Pressure Ratio ◽  
Humid Air ◽  
Air Turbine ◽  
Water Atomization ◽  
Air Cooler ◽  
Compressor Work

The AHAT (advanced humid air turbine) system, which can be equipped with a heavy-duty, single-shaft gas turbine, aims at high efficiency equal to that of the HAT system. Instead of an intercooler, a WAC (water atomization cooling) system is used to reduce compressor work. The characteristics of a humidification tower (a saturator), which is used as a humidifier for the AHAT system, were studied. The required packing height and the exit water temperature from the humidification tower were analyzed for five virtual gas turbine systems with different capacities (1MW, 3.2MW, 10MW, 32MW and 100MW) and pressure ratios (π = 8, 12, 16, 20 and 24). Thermal efficiency of the system was compared with that of a simple cycle and a recuperative cycle with and without the WAC system. When the packing height of the humidification tower was changed, the required size varied for the three heat exchangers around the humidification tower (a recuperator, an economizer and an air cooler). The packing height with which the sum total of the size of the packing and these heat exchangers became a minimum was 1m for the lowest pressure ratio case, and 6m for the highest pressure ratio case.

Optimization of an Organic Rankine Cycle-Based Waste Heat Recovery System Using a Novel Target-Temperature-Line Approach

2021 ◽  
Vol 143 (9) ◽  
Author(s):  
Md. Zahurul Haq
Keyword(s):  
Heat Exchange ◽  
Heat Recovery ◽  
Waste Heat Recovery ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Optimum Operating ◽  
Working Fluid ◽  
Operating Parameters ◽  
Target Temperature

Abstract Organic Rankine cycle (ORC)-based waste heat recovery (WHR) systems are simple, flexible, economical, and environment-friendly. Many working fluids and cycle configurations are available for WHR systems, and the diversity of working fluid properties complicates the synergistic integration of the efficient heat exchange in the evaporator and net output work. Unique guidelines to select a proper working fluid, cycle configuration and optimum operating parameters are not readily available. In the present study, a simple target-temperature-line approach is introduced to get the optimum operating parameters for the subcritical ORC system. The target-line is the locus of temperatures satisfying the pinch-point temperature difference along the length of the heat exchanger. Employing the approach, study is carried out with 38 pre-selected working fluids to get the optimum operating parameters and suitable fluid for heat source temperatures ranging from 100 °C to 300 °C. Results obtained are analyzed to get cross-correlations between key operating and performance parameters using a heat-map diagram. At the optimum condition, optimal working fluid’s critical temperature and pressure, evaporator saturation temperature, effectivenesses of the heat exchange in the evaporator, cycle, and overall WHR system exhibit strong linear correlations with the heat source temperature.

scholarly journals Birth of a Live Cria After Transfer of a Vitrified-Warmed Alpaca (Vicugna pacos) Preimplantation Embryo

2020 ◽  
Vol 7 ◽  
Author(s):  
Jennifer C. Lutz ◽  
Susan L. Johnson ◽  
Kimberly J. Duprey ◽  
Paul J. Taylor ◽  
Henry William Vivanco-Mackie ◽  
...  
Keyword(s):  
Ethylene Glycol ◽  
Preimplantation Embryos ◽  
Embryo Survival ◽  
Important Species ◽  
Vicugna Pacos ◽  
Improvement Programs ◽  
The One ◽  
Humidified Air

The alpaca (Vicugna pacos) is an important species for the production of fiber and food. Genetic improvement programs for alpacas have been hindered, however, by the lack of field-practical techniques for artificial insemination and embryo transfer. In particular, successful techniques for the cryopreservation of alpaca preimplantation embryos have not been reported previously. The objective of this study was to develop a field-practical and efficacious technique for cryopreservation of alpaca preimplantation embryos using a modification of a vitrification protocol originally devised for horses and adapted for dromedary camels. Four naturally cycling non-superovulated Huacaya females serving as embryo donors were mated to males of proven fertility. Donors received 30 μg of gonadorelin at the time of breeding, and embryos were non-surgically recovered 7 days after mating. Recovered embryos (n = 4) were placed individually through a series of three vitrification solutions at 20°C (VS1: 1.4 M glycerol; VS2: 1.4 M glycerol + 3.6 M ethylene glycol; VS3: 3.4 M glycerol + 4.6 M ethylene glycol) before loading into an open-pulled straw (OPS) and plunging directly into liquid nitrogen for storage. At warming, each individual embryo was sequentially placed through warming solutions (WS1: 0.5 M galactose at 37°C; WS2: 0.25 M galactose at 20°C), and warmed embryos were incubated at 37°C in 5% CO2 in humidified air for 20–22 h in 1 ml Syngro® holding medium supplemented with 10% (v/v) alpaca serum to perform an initial in vitro assessment of post-warming viability. Embryos whose diameter increased during culture (n = 2) were transferred individually into synchronous recipients, whereas embryos that did not grow (n = 2) were transferred together into a single recipient to perform an in vivo assessment of post-warming viability. Initial pregnancy detection was performed ultrasonographically 29 days post-transfer when fetal heartbeat could be detected, and one of three recipients was pregnant (25% embryo survival rate). On November 13, 2019, the one pregnant recipient delivered what is believed to be the world's first cria produced from a vitrified-warmed alpaca embryo.

Sign in / Sign up

Export Citation Format

Share Document