Pressure-Side Bleed Film Cooling: Part II — Unsteady Framework for Experimental and Computational Results

2002 ◽  
Author(s):  
D. Scott Holloway ◽  
James H. Leylek ◽  
Frederick A. Buck
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Viscous Sublayer ◽  
Pressure Side ◽  
Unusual Behavior ◽  
High Quality ◽  
Injection Point ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Unsteady Simulation

This study examines the unsteady transonic pressure-side bleed film cooling on the trailing edge of a turbine blade and resolves the key mechanism responsible for the unusual relationship between film cooling effectiveness and increasing blowing ratio. This study is meant to show that unsteadiness is the key mechanism causing the unexpected results seen in the experiments. It is believed that this unsteadiness is highly dependent on the ratio of the lip thickness to slot height and the shedding frequencies of the passage and coolant vortices, which depend on blowing ratio. For low blowing ratio, hot passage flow has the dominant vortices. For high blowing ratio, coolant flow has the dominant vortices. For intermediate blowing ratio, the vortices have the potential to interact and cause the unusual behavior seen in pressure-side bleed film cooling. On the basis of these observations, experiments were repeated with pressure probes used to acquire the shedding frequencies at the effectiveness measurement location, which showed that unsteadiness was indeed present. Realistic engine conditions are considered with lip thickness to slot height ratio of 0.9 and mainstream Mach numbers of 0.7 at the coolant injection point and expanding to sonic conditions at the exit plane of the test section. Numerical results are from a 2-D mid-plane cut of the original geometry and a full-pitch 3-D model. Computations use high quality grids, high order discretization schemes, and an advanced turbulence model. The 3-D grid consists of 4.4 million cells and a high quality, unstructured, multi-topology mesh with resolution of the viscous sublayer and y+ < 1 on all surfaces. The simulations are fully converged, time accurate, and grid-independent. A novel methodology is used to introduce unsteadiness into the simulations. Effects of blowing ratio are examined, where blowing ratio is equal to 1.0 for 3-D and ranges from 0.3 to 1.5 for 2-D with a density ratio of 1.52. By performing an unsteady simulation, the unusual relationship between the effectiveness and blowing ratio is demonstrated in an unsteady framework.

Influence of Coolant Density on Turbine Blade Film Cooling at Transonic Cascade Flow Conditions Using the Pressure Sensitive Paint Technique

2021 ◽  
Author(s):  
Izhar Ullah ◽  
Sulaiman M. Alsaleem ◽  
Lesley M. Wright ◽  
Chao-Cheng Shiau ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Pressure Side ◽  
Pressure Sensitive Paint ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Pressure Sensitive ◽  
Blade Tip ◽  
Film Cooling Holes

Abstract This work is an experimental study of film cooling effectiveness on a blade tip in a stationary, linear cascade. The cascade is mounted in a blowdown facility with controlled inlet and exit Mach numbers of 0.29 and 0.75, respectively. The free stream turbulence intensity is measured to be 13.5 % upstream of the blade’s leading edge. A flat tip design is studied, having a tip gap of 1.6%. The blade tip is designed to have 15 shaped film cooling holes along the near-tip pressure side (PS) surface. Fifteen vertical film cooling holes are placed on the tip near the pressure side. The cooling holes are divided into a 2-zone plenum to locally maintain the desired blowing ratios based on the external pressure field. Two coolant injection scenarios are considered by injecting coolant through the tip holes only and both tip and PS surface holes together. The blowing ratio (M) and density ratio (DR) effects are studied by testing at blowing ratios of 0.5, 1.0, and 1.5 and three density ratios of 1.0, 1.5, and 2.0. Three different foreign gases are used to create density ratio effect. Over-tip flow leakage is also studied by measuring the static pressure distributions on the blade tip using the pressure sensitive paint (PSP) measurement technique. In addition, detailed film cooling effectiveness is acquired to quantify the parametric effect of blowing ratio and density ratio on a plane tip design. Increasing the blowing ratio and density ratio resulted in increased film cooling effectiveness at all injection scenarios. Injecting coolant on the PS and the tip surface also resulted in reduced leakage over the tip. The conclusions from this study will provide the gas turbine designer with additional insight on controlling different parameters and strategically placing the holes during the design process.

Numerical Investigation on Film Cooling Effectiveness of Stator Blade with Different Density Ratio

2014 ◽  
Vol 521 ◽  
pp. 104-107
Author(s):  
Ling Zhang ◽  
Quan Heng Jin ◽  
Da Fei Guo
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Leading Edge ◽  
Suction Side ◽  
Pressure Side ◽  
Middle Section ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Stator Blade

The Realizable k-ε turbulence model was performed to investigate the film cooling effectiveness with different blowing ratio 1,1.5,2 and different density ratio 1,1.5,2.The results show that, cooling effectiveness increases with the augment of blowing ratio. On the pressure side, cooling effectiveness increases with the augment of density ratio. On the suction side, with higher density ratio the leading edge cooling increases, the middle section reduces, and the trailing edge cooling effectiveness increases first decreases.

Pressure-Side Bleed Film Cooling: Part I — Steady Framework for Experimental and Computational Results

2002 ◽  
Author(s):  
D. Scott Holloway ◽  
James H. Leylek ◽  
Frederick A. Buck
Keyword(s):  
Test Section ◽  
Film Cooling ◽  
Density Ratio ◽  
Experimental Results ◽  
Test Surface ◽  
Pressure Side ◽  
Computational Results ◽  
Height Ratio ◽  
High Quality ◽  
Blowing Ratio

This study combines both experiments and computations to investigate pressure-side bleed on the trailing edge of a turbine blade. Realistic engine conditions are considered with a lip thickness to slot height ratio of 0.9 and mainstream Mach numbers of 0.7 at the coolant injection point expanding to sonic conditions at the exit plane of the test section. The purpose of this study is to understand the complex physics of pressure-side bleed, in particular, the unusual behavior that occurs with increasing blowing ratio. Experimentally, it is shown that as the blowing ratio increases, the film cooling effectiveness at a point near the end of the test section increases for blowing ratios less than 0.8, while decreasing over the range of blowing ratios from 1.0 through 1.25. For blowing ratios higher than 1.25, effectiveness increases. This phenomenon has been repeated experimentally for many years without being fully understood. Parts I and II of this paper describe the mechanism responsible for the unusual experimental results. This mechanism is unsteady vortex shedding. Experimental results are from a row of jets with the use of foreign gas injection that simulates the engine conditions that would be seen by the pressure side of an airfoil with pressure-side bleed. These results consist of the pressure distribution due to the nozzle and the effectiveness along the test surface downstream of the injection site. The computational model is designed to replicate the experimental setup. High-quality grids, high-order discretization schemes, and an advanced turbulence model are employed to ensure that the computational results can be used to explain the complex physics of transonic pressure-side bleed film cooling. The grid consists of 2.2 million cells and a high-quality, unstructured, multi-topology, super-block mesh with the resolution of the viscous sub-layer and y+ < 1 on all surfaces. The simulations are fully converged and grid-independent. Effects of blowing ratio are examined, with blowing ratio ranging from 0.5 to 2.0 and a density ratio of 1.52. The geometry consists of not only the transonic mainstream flow and the jet, but also the creeping plenum flow. As a result of the significant lip thickness to slot height ratio, it is shown that unsteady effects are the dominant mechanism in the physics of pressure-side bleed film cooling.

Influence of Coolant Density on Turbine Blade Tip Film Cooling at Transonic Cascade Flow Conditions Using the Pressure Sensitive Paint Technique

2021 ◽  
pp. 1-33
Author(s):  
Izhar Ullah ◽  
Sulaiman Alsaleem ◽  
Lesley Wright ◽  
Chao-Cheng Shiau ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Pressure Side ◽  
Pressure Sensitive Paint ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Pressure Sensitive ◽  
Blade Tip ◽  
Film Cooling Holes

Abstract This work is an experimental study of film cooling effectiveness on a blade tip in a stationary, linear cascade. The cascade is mounted in a blowdown facility with controlled inlet and exit Mach numbers of 0.29 and 0.75, respectively. The free stream turbulence intensity is measured to be 13.5 % upstream of the blade's leading edge. A flat tip design is studied, having a tip gap of 1.6%. The blade tip is designed to have 15 shaped film cooling holes along the near-tip pressure side (PS) surface. Fifteen vertical film cooling holes are placed on the tip near the pressure side. The cooling holes are divided into a 2-zone plenum to locally maintain the desired blowing ratios based on the external pressure field. Two coolant injection scenarios are considered by injecting coolant through the tip holes only and both tip and PS surface holes together. The blowing ratio (M) and density ratio (DR) effects are studied by testing at blowing ratios of 0.5, 1.0, and 1.5 and three density ratios of 1.0, 1.5, and 2.0. Three different foreign gases are used to create density ratio effect. Over-tip flow leakage is also studied by measuring the static pressure distributions on the blade tip using the pressure sensitive paint measurement technique. In addition, detailed film cooling effectiveness and over-tip flow leakage is acquired to quantify the parametric effect of blowing ratio and density ratio on a plane tip.

Influence of Coolant Density on Turbine Platform Film-Cooling With Stator–Rotor Purge Flow and Compound-Angle Holes

2014 ◽  
Vol 6 (4) ◽  
Author(s):  
Kevin Liu ◽  
Shang-Feng Yang ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Fundamental Parameters ◽  
Blowing Ratio ◽  
Purge Flow ◽  
Cylindrical Holes ◽  
Exit Mach Number ◽  
Compound Angle

A detailed parametric study of film-cooling effectiveness was carried out on a turbine blade platform. The platform was cooled by purge flow from a simulated stator–rotor seal combined with discrete hole film-cooling. The cylindrical holes and laidback fan-shaped holes were accessed in terms of film-cooling effectiveness. This paper focuses on the effect of coolant-to-mainstream density ratio on platform film-cooling (DR = 1 to 2). Other fundamental parameters were also examined in this study—a fixed purge flow of 0.5%, three discrete-hole film-cooling blowing ratios between 1.0 and 2.0, and two freestream turbulence intensities of 4.2% and 10.5%. Experiments were done in a five-blade linear cascade with inlet and exit Mach number of 0.27 and 0.44, respectively. Reynolds number of the mainstream flow was 750,000 and was based on the exit velocity and chord length of the blade. The measurement technique adopted was the conduction-free pressure sensitive paint (PSP) technique. Results indicated that with the same density ratio, shaped holes present higher film-cooling effectiveness and wider film coverage than the cylindrical holes, particularly at higher blowing ratios. The optimum blowing ratio of 1.5 exists for the cylindrical holes, whereas the effectiveness for the shaped holes increases with an increase of blowing ratio. Results also indicate that the platform film-cooling effectiveness increases with density ratio but decreases with turbulence intensity.

Influence of Turbine Blade Leading Edge Profile on Film Cooling With Shaped Holes

2017 ◽  
Author(s):  
Mingjie Zhang ◽  
Nian Wang ◽  
Andrew F. Chen ◽  
Je-Chin Han
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Density Ratio ◽  
Leading Edge ◽  
Stagnation Line ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Edge Profile ◽  
Elliptical Cylinders ◽  
Blade Leading Edge

This paper presents the turbine blade leading edge model film cooling effectiveness with shaped holes, using the pressure sensitive paint (PSP) mass transfer analogy method. The effects of leading edge profile, coolant to mainstream density ratio and blowing ratio are studied. Computational simulations are performed using the realizable k-ε turbulence model. Effectiveness obtained by CFD simulations are compared with experiments. Three leading edge profiles, including one semi-cylinder and two semi-elliptical cylinders with an after body, are investigated. The ratios of major to minor axis of two semi-elliptical cylinders are 1.5 and 2.0, respectively. The leading edge has three rows of shaped holes. For the semi-cylinder model, shaped holes are located at 0 degrees (stagnation line) and ± 30 degrees. Row spacing between cooling holes and the distance between impingement plate and stagnation line are the same for three leading edge models. The coolant to mainstream density ratio varies from 1.0 to 1.5 and 2.0, and the blowing ratio varies from 0.5 to 1.0 and 1.5. Mainstream Reynolds number is about 100,900 based on the diameter of the leading edge cylinder, and the mainstream turbulence intensity is about 7%. The results provide an understanding of the effects of leading edge profile and on turbine blade leading edge region film cooling with shaped-hole designs.

Numerical Investigation of Coolant-to-Mainstream Scaling Parameters With Film Cooling on Pressure and Suction Side of a Gas Turbine Blade

2017 ◽  
Author(s):  
Lingyu Zeng ◽  
Xueying Li ◽  
Jing Ren ◽  
Hongde Jiang
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Momentum Flux ◽  
Velocity Ratio ◽  
Density Ratio ◽  
Flux Ratio ◽  
Suction Side ◽  
Pressure Side ◽  
Blowing Ratio ◽  
Adiabatic Effectiveness

Most experiments of blade film cooling are conducted with density ratio lower than that of turbine conditions. In order to accurately model the performance of film cooling under a high density ratio, choosing an appropriate coolant to mainstream scaling parameter is necessary. The effect of density ratio on film cooling effectiveness on the surface of a gas turbine twisted blade is investigated from a numerical point of view. One row of film holes are arranged in the pressure side and two rows in the suction side. All the film holes are cylindrical holes with a pitch to diameter ratio P/d = 8.4. The inclined angle is 30°on the pressure side and 34° on the suction side. The steady solutions are obtained by solving Reynolds-Averaged-Navier-Stokes equations with a finite volume method. The SST turbulence model coupled with γ-θ transition model is applied for the present simulations. A film cooling experiment of a turbine vane was done to validate the turbulence model. Four different density ratios (DR) from 0.97 to 2.5 are studied. To independently vary the blowing ratio (M), momentum flux ratio (I) and velocity ratio (VR) of the coolant to the mainstream, seven conditions (M varying from 0.25 to 1.6 on the pressure side and from 0.25 to 1.4 on the suction side) are simulated for each density ratio. The results indicate that the adiabatic effectiveness increases with the increase of density ratio for a certain blowing ratio or a certain momentum flux ratio. Both on the pressure side and suction side, none of the three parameters listed above can serve as a scaling parameter independent of density ratio in the full range. The velocity ratio provides a relative better collapse of the adiabatic effectiveness than M and I for larger VRs. A new parameter describing the performance of film cooling is introduced. The new parameter is found to be scaled with VR for nearly the whole range.

The Influence of Purge Flow Parameters on Heat Transfer and Film Cooling in Turbine Center Frames

2021 ◽  
Author(s):  
Patrick R. Jagerhofer ◽  
Marios Patinios ◽  
Tobias Glasenapp ◽  
Emil Göttlich ◽  
Federica Farisco
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Convective Heat Transfer Coefficient ◽  
Density Ratio ◽  
Constant Heat Flux ◽  
High Pressure Turbine ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Purge Flow

Abstract Due to stringent environmental legislation and increasing fuel costs, the efficiencies of modern turbofan engines have to be further improved. Commonly, this is facilitated by increasing the turbine inlet temperatures in excess of the melting point of the turbine components. This trend has reached a point where not only the high-pressure turbine has to be adequately cooled, but also components further downstream in the engine. Such a component is the turbine center frame (TCF), having a complex aerodynamic flow field that is also highly influenced by purge-mainstream interactions. The purge air, being injected through the wheelspace cavities of the upstream high-pressure turbine, bears a significant cooling potential for the TCF. Despite this, fundamental knowledge of the influencing parameters on heat transfer and film cooling in the TCF is still missing. This paper examines the influence of purge-to-mainstream blowing ratio, purge-to-mainstream density ratio and purge flow swirl angle on the convective heat transfer coefficient and the film cooling effectiveness in the TCF. The experiments are conducted in a sector-cascade test rig specifically designed for such heat transfer studies using infrared thermography and tailor-made flexible heating foils with constant heat flux. The inlet flow is characterized by radially traversing a five-hole-probe. Three purge-to-mainstream blowing ratios and an additional no purge case are investigated. The purge flow is injected without swirl and also with engine-similar swirl angles. The purge swirl and blowing ratio significantly impact the magnitude and the spread of film cooling in the TCF. Increasing blowing ratios lead to an intensification of heat transfer. By cooling the purge flow, a moderate variation in purge-to-mainstream density ratio is investigated, and the influence is found to be negligible.

Implementation of Hole-Pair in Ramp to Improve Film Cooling Effectiveness on a Plain Surface

2020 ◽  
Author(s):  
Sadam Hussain ◽  
Xin Yan
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Density Ratio ◽  
Hole Pair ◽  
Cooling Effect ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Cooling Hole ◽  
Plain Surface

Abstract Film cooling is one of the most critical technologies in modern gas turbine engine to protect the high temperature components from erosion. It allows gas turbines to operate above the thermal limits of blade materials by providing the protective cooling film layer on outer surfaces of blade against hot gases. To get a higher film cooling effect on plain surface, current study proposes a novel strategy with the implementation of hole-pair into ramp. To gain the film cooling effectiveness on the plain surface, RANS equations combined with k-ω turbulence model were solved with the commercial CFD solver ANSYS CFX11.0. In the numerical simulations, the density ratio (DR) is fixed at 1.6, and the film cooling effect on plain surface with different configurations (i.e. with only cooling hole, with only ramp, and with hole-pair in ramp) were numerically investigated at three blowing ratios M = 0.25, 0.5, and 0.75. The results show that the configuration with Hole-Pair in Ramp (HPR) upstream the cooling hole has a positive effect on film cooling enhancement on plain surface, especially along the spanwise direction. Compared with the baseline configuration, i.e. plain surface with cylindrical hole, the laterally-averaged film cooling effectiveness on plain surface with HPR is increased by 18%, while the laterally-averaged film cooling effectiveness on plain surface with only ramp is increased by 8% at M = 0.5. As the blowing ratio M increases from 0.25 to 0.75, the laterally-averaged film cooling effectiveness on plain surface with HPR is kept on increasing. At higher blowing ratio M = 0.75, film cooling effectiveness on plain surface with HPR is about 19% higher than the configuration with only ramp.

Effect of Coolant Density on Leading Edge Showerhead Film Cooling Using PSP Measurement Technique

2013 ◽  
Author(s):  
Shiou-Jiuan Li ◽  
Shang-Feng Yang ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Leading Edge ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Pressure Sensitive ◽  
Cylindrical Holes ◽  
Film Cooling Holes ◽  
Compound Angle ◽  
Low Speed Wind Tunnel

The density ratio effect on leading edge showerhead film cooling has been studied experimentally using the pressure sensitive paint (PSP) mass transfer analogy method. Leading edge model is a blunt body with a semi-cylinder and an after body. There are two designs: seven-row and three-row of film cooling holes for simulating vane and blade, respectively. The film holes are located at 0 (stagnation row), ±15, ±30, and ±45 deg for seven-row design, and at 0 and ±30 for three-row design. Four film holes configurations are used for both test designs: radial angle cylindrical holes, compound angle cylindrical holes, radial angle shaped holes, and compound angle shaped holes. Coolant to mainstream density ratio varies from DR = 1.0, 1.5, to 2.0 while blowing ratio varies from M = 0.5 to 2.1. Experiments were conducted in a low speed wind tunnel with Reynolds number 100,900 based on mainstream velocity and diameter of the cylinder. The mainstream turbulence intensity near leading edge model is about 7%. The results show the shaped holes have overall higher film cooling effectiveness than cylindrical holes, and radial angle holes are better than compound angle holes, particularly at higher blowing ratio. Larger density ratio makes more coolant attach to the surface and increases film protection for all cases. Radial angle shaped holes provides best film cooling at higher density ratio and blowing ratio for both designs.

Sign in / Sign up

Export Citation Format

Share Document