Performance and Emissions Characteristics of Philippine CME-Diesel Blends

2017 ◽  
Author(s):  
Edwin N. Quiros ◽  
Jeffrey James C. Laguitao
Keyword(s):  
Fuel Economy ◽  
The Philippines ◽  
Emissions Reduction ◽  
Nox Emissions ◽  
Gaseous Emissions ◽  
Performance Loss ◽  
Oxygenated Fuel ◽  
Performance And Emissions ◽  
Utility Vehicle ◽  
Lower Heating

Deliberations in the Philippines are underway on the shift to 5% (B5) CME-diesel blend from the current B2 blend. In support to said deliberations, a fuel economy and gaseous emissions study of B1–B50 CME-diesel blends was conducted using an in-use Asian utility vehicle running on the Japanese 10–15 Mode drive cycle. Results show that adding CME up to 20% by volume (B20) has a small effect on the heating values, specific fuel consumption (SFC), mileage, and maximum power. Relative to neat diesel, the increase in SFC, and lower mileage and power beyond B20 were attributed to lower heating values at higher blends. CO was practically constant while THC and NOx generally decreased with increasing CME blends. The CO and THC trends were ascribed to overall lean mixtures and increased amount of oxygenated fuel at higher CME blends. The decreasing NOx trend needs further investigation as it seemed contrary to other studies. Based on these results, the shift to B5 would insignificantly affect fuel economy and likely lessen THC and NOx emissions. B20 yielded the most emissions reduction without performance loss.

Performance and Emissions of a CRDI Passenger Van Using CME-Diesel Blends

2018 ◽  
Author(s):  
Edwin N. Quiros ◽  
Rupert Karlo D. Aguila ◽  
Manuel V. Hernandez ◽  
Joseph Gerard T. Reyes ◽  
Jose Gabriel E. Mercado
Keyword(s):  
Fuel Consumption ◽  
Fossil Fuels ◽  
Direct Injection ◽  
Clean Energy ◽  
The Philippines ◽  
Marginal Effect ◽  
Fuel Blend ◽  
Performance Loss ◽  
Diesel Fuels ◽  
Performance And Emissions

In a move to reduce dependence on imported fossil fuels, develop and utilize indigenous renewable and sustainably-sourced clean energy sources, the Philippines enacted the Biofuels Act of 2006 (or Republic Act 9367) that mandated blending of biodiesel with commercially sold diesel fuels which presently is at 2% coconut methyl ester (CME) by volume. Deliberations are underway to shift to 5% by volume so that data on the effects on performance and emissions of percentage blends are necessary. This study presents fuel consumption and emissions measurements of an in-use passenger van with a common-rail direct injection (CRDI) powertrain fueled with 2, 5, 10, & 20 percent CME-diesel blends by volume (designated as B2, B5, B10, & B20 respectively) driven on the Japanese 10–15 Mode drive cycle. Results indicate B2-B20 had only a marginal effect on heating values, fuel blend density, and maximum power. Relative to neat diesel, the blends showed a 1–5% lower specific fuel consumption (SFC) with B5 lowest. Mileage was 1–5% higher with the blends with B5 highest. CO decreased with increasing blend. THC emissions of B1-B20 were roughly half that of diesel. NOx from the CME blends was marginally lower than diesel. The CO and THC trends agreed with published literature and usually ascribed to overall lean mixtures and increased amount of oxygenated fuel at higher CME blends. The NOx results need further investigation as it seemed to contradict other studies. Based on these results, B5 yielded the best combination of fuel economy and emissions improvement over neat diesel and B2 without performance loss.

Fuel Economy and Emissions of Philippine CME-Diesel Blends From Drive Cycle and Steady Speed Operation

2020 ◽  
Author(s):  
Jeffrey James C. Laguitao ◽  
Edwin N. Quiros ◽  
Jose Gabriel E. Mercado ◽  
Paul L. Rodgers
Keyword(s):  
Fuel Consumption ◽  
Fuel Economy ◽  
Direct Injection ◽  
The Philippines ◽  
Vehicle Speed ◽  
Drive Cycle ◽  
Performance Loss ◽  
Vehicle Operation ◽  
Blend Fuel ◽  
All Speeds

Abstract This paper presents a study on the effects of transient and steady-state vehicle operation on fuel economy and emissions trends of an in-use Euro 2 Asian utility vehicle in the Philippines, with a normally aspirated direct-injection engine, and fueled with different CME-diesel blends designated as B1, B2, B3, B5, B10, B20, B50, & B100 corresponding to increasing CME percentage blends. The vehicle was driven on a chassis dynamometer following the Japanese 10-15 Mode drive cycle and at steady speeds of 40, 60, & 80 kph for fuel consumption and CO, NOx, and THC measurements. PM measurements were not undertaken. Drive cycle results showed that adding CME up to 20% by volume (B20) has a small effect on the heating values, specific fuel consumption (SFC), fuel economy (FE), and maximum power. Relative to neat diesel, the increase in SFC, lower FE and power beyond B20 were attributed to lower heating values at higher blends. CO was practically constant while THC and NOx generally decreased with increasing CME blends. The CO and THC trends were ascribed to overall lean mixtures and increased amount of oxygenated fuel at higher CME blends. B20 yielded the most emissions reduction without performance loss. Steady speed results indicated for all blends, SFC increased with vehicle speed due to higher road load. Above B10, SFC went beyond 5% higher than that for neat diesel and is attributed to lowered heating values of higher blends. The SFC of blends up to B10 approached that of neat diesel as speed increased suggesting more diesel-like combustion characteristics. The blend fuel economy showed an inverse relationship to SFC as expected. Both CO and NOx exhibited slightly decreasing trends with higher blends at all speeds. For a given blend, CO decreased while NOx increased as speed went higher. THC followed bowl-shaped trendlines with blend ratio. THC was high for neat diesel going lowest at B5-B10 and upwards again beyond B10. For a given blend, THC emissions decreased with increasing vehicle speed.

Methodology to Evaluate the Fuel Economy of a Multimode Combustion Engine With Three-Way Catalytic Converter

2014 ◽  
Author(s):  
Sandro P. Nüesch ◽  
Anna G. Stefanopoulou ◽  
Li Jiang ◽  
Jeffrey Sterniak
Keyword(s):  
Fuel Economy ◽  
Combustion Engine ◽  
Catalytic Converter ◽  
Oxygen Storage ◽  
Nox Emissions ◽  
Combustion Mode ◽  
Mode Switch ◽  
Drive Cycle ◽  
Finite State ◽  
The Impact

Highly diluted, low temperature homogeneous charge compression ignition (HCCI) combustion leads to ultra-low levels of engine-out NOx emissions. A standard drive cycle, however, would require switches between HCCI and spark-ignited (SI) combustion modes. In this paper a methodology is introduced, investigating the fuel economy of such a multimode combustion concept in combination with a three-way catalytic converter (TWC). The TWC needs to exhibit unoccupied oxygen storage sites in order to show acceptable performance. But the lean exhaust gas during HCCI operation fills the oxygen storage and leads to a drop in NOx conversion efficiency. Eventually the levels of NOx become unacceptable and a mode switch to a fuel rich combustion mode is necessary in order to deplete the oxygen storage. The resulting lean-rich cycling leads to a penalty in fuel economy. In order to evaluate the impact of those penalties on fuel economy, a finite state model for combustion mode switches is combined with a longitudinal vehicle model and a phenomenological TWC model, focused on oxygen storage. The aftertreatment model is calibrated using combustion mode switch experiments from lean HCCI to rich spark-assisted HCCI and back. Fuel and emissions maps acquired in steady state experiments are used. Two depletion strategies are compared in terms of their influence on drive cycle fuel economy and NOx emissions.

Effect of Biodiesel, JP-8 and Ultra Low Sulfur Diesel Fuel on Autoignition, Combustion, Performance and Emissions in a Single Cylinder Diesel Engine

2010 ◽  
Author(s):  
Chandrasekharan Jayakumar ◽  
Jagdish Nargunde ◽  
Anubhav Sinha ◽  
Walter Bryzik ◽  
Naeim A. Henein ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Properties ◽  
Nox Emissions ◽  
Single Cylinder ◽  
Combustion Performance ◽  
Ultra Low Sulfur Diesel ◽  
Diffusion Controlled ◽  
Performance And Emissions ◽  
Combustion Fraction ◽  
Low Sulfur

Concern about the depletion of petroleum reserves, rising prices of conventional fuels, security of supply and global warming have driven research toward the development of renewable fuels for use in diesel engines. These fuels have different physical and chemical properties that affect the diesel combustion process. This paper compares between the autoignition, combustion, performance and emissions of soybean derived biodiesel, JP-8 and ultra low sulfur diesel (ULSD) in a high speed single-cylinder research diesel engine equipped with a common rail injection system. Tests were conducted at steady state conditions at different injection pressures ranging from 600 bar to 1200 bar. The ‘rate of heat release’ traces are analyzed to determine the effect of fuel properties on the ignition delay, premixed combustion fraction and mixing and diffusion controlled combustion fractions. Biodiesel produced the largest diffusion controlled combustion fraction at all injection pressures compared to ULSD and JP-8. At 600 bar injection pressure, the diffusion controlled combustion fraction for biodiesel was 53% whereas both JP-8 and ULSD produced 39%. In addition, the effect of fuel properties on engine performance, fuel economy, and engine-out emissions is determined. On an average JP-8 produced 3% higher thermal efficiency than ULSD. Special attention is given to the NOx emissions and particulate matter characteristics. On an average biodiesel produced 37% less NOx emissions compared to ULSD and JP-8.

Diesel Emissions Reduction Using a Catalyst and Water Scrubber for Underground Mine Applications

1988 ◽  
Vol 202 (4) ◽  
pp. 233-242
Author(s):  
G E Andrews ◽  
R Everest ◽  
D Jepson ◽  
S W Pang
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Substantial Reduction ◽  
Diesel Emissions ◽  
Emissions Reduction ◽  
Gaseous Emissions ◽  
Engine Exhaust ◽  
Particulate Removal ◽  
Water Scrubber ◽  
Exhaust Particulate

BS 6680 requires the efficiency of coalmine diesel engine exhaust pollution-reduction devices to be determined. The efficiency of an Englehard PTX catalyst and water scubber for both particulate and gaseous emissions reduction was determined using a 533 cc single-cylinder Petter AVI direct injection diesel engine. The separate and combined influence of the two exhaust devices was determined. The water scrubber acted as aflame trap as well as an exhaust particulate trap. The catalyst gave a substantial reduction in CO and UHC gaseous emissions and particulate SOF emissions for exhaust temperatures above 250°C. However, the high MW particulate SOF, including the PAH, had a 70 per cent reduction for catalyst temperatures as low as 200°C. The water scrubber was the dominant particulate removal device, although the catalyst removal efficiency was significant for temperatures above 250° C. The scrubber also had a significant influence on the reduction in NOx emissions, with a 30 per cent removal at high exhaust temperatures.

scholarly journals Review of Performance and Emmissions Characteristics of Bio-Additive Fuel on SI Engine Fuelled by Biopetrol

2015 ◽  
Vol 773-774 ◽  
pp. 430-434
Author(s):  
Azizul Mokhtar ◽  
Nazrul Atan ◽  
Najib Rahman ◽  
Amir Khalid
Keyword(s):  
Fuel Economy ◽  
Fossil Fuels ◽  
Review Paper ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
Spark Ignition Engine ◽  
Si Engine ◽  
New Approach ◽  
Performance And Emission ◽  
Performance And Emissions

Bio-additive is biodegradable and produces less air pollution thus significant for replacing the limited fossil fuels and reducing threats to the environment from exhaust emissions and global warming. Instead, the bio-additives can remarkably improve the fuel economy SI engine while operating on all kinds of fuel. Some of the bio-additive has the ability to reduce the total CO2 emission from internal petrol engine. This review paper focuses to determine a new approach in potential of bio-additives blends operating with bio-petrol on performance and emissions of spark ignition engine. It is shown that the variant in bio-additives blending ratio and engine operational condition are reduced engine-out emissions and increased efficiency. It seems that the bio-additives can increase the maximum cylinder combustion pressure, improve exhaust emissions and largely reduce the friction coefficient. The review concludes that the additives usage in bio-petrol is inseparable for the better engine performance and emission control and further research is needed to develop bio-petrol specific additives.

scholarly journals Public utility vehicle service quality and customer satisfaction in the Philippines during the COVID-19 pandemic

2022 ◽  
pp. 101336
Author(s):  
Thanatorn Chuenyindee ◽  
S. Ong Ardvin Kester ◽  
Jon Pauline Ramos ◽  
Yogi Tri Prasetyo ◽  
Reny Nadlifatin ◽  
...  
Keyword(s):  
Customer Satisfaction ◽  
Service Quality ◽  
The Philippines ◽  
Public Utility ◽  
Utility Vehicle

US Fishing Vessel Powering and NOx Emissions

2007 ◽  
Vol 44 (03) ◽  
pp. 175-179
Author(s):  
Robert G. Latorre ◽  
Joseph P. Cardella V
Keyword(s):  
Diesel Engine ◽  
Emissions Reduction ◽  
Nox Emissions ◽  
Fishing Vessel ◽  
Fishing Fleet ◽  
The Us ◽  
Small Craft ◽  
Index Ratio

This paper presents the results of SNAME Small Craft Panel SC-3 Fishing Systems investigation of trends in US fishing vessel (Fig. 1) (L> 22.9 m) powering and NOx emissions (1900–2000). The study estimates the 1, 299 vessels in the US fishing fleet produce 306 tons/day of NOx. The largest powers are found in the decades of 1960–1980. The actual power kW is compared to a reference power kWo using the Powering Index Ratio PIR = kW/kWo. It was found that 50 to 80% of the power in seiners, trawlers, and crabber/ trapper/clam vessels have PIR > 2.5. The reduction of fishing vessel diesel engine NOx can be best achieved by adopting acceptable levels of vessel power/length for the basis of revenue and tax rather than using the vessel age as emissions reduction criteria.

Evaluation of Fuel Economy and Emissions Reduction for a Motorcycle With Automatic Idling-Stop Device

2014 ◽  
Vol 136 (2) ◽  
Author(s):  
Chih-Hsien Yu ◽  
Chyuan-Yow Tseng ◽  
Shiunn-Cheng Chuang
Keyword(s):  
Fuel Economy ◽  
Fuel Injection ◽  
Control Unit ◽  
Engine Control Unit ◽  
Emissions Reduction ◽  
Fuel Saving ◽  
Chassis Dynamometer ◽  
Stop And Go ◽  
And Control ◽  
Co Emission

In an attempt to improve the fuel economy and reduce the exhaust emissions of motorcycles, some manufactures have developed commercialized motorcycles equipped with automatic idling-stop and go (AISG) functionality. Even though research efforts devoted to the idling-stop strategy have demonstrated its effectiveness, motorcycles equipped with the AISG device are not popular because the general public still has some concerns about them. This paper aims to evaluate the benefits and feasibility of a commercialized motorcycle with AISG functionality with regard to the public's concerns about fuel economy and emission problems during engine restart transients. In order to verify the accuracy of the analytical results and control for variable driver characteristics, a motorcycle chassis dynamometer was used to recreate the urban driving pattern. Furthermore, the feasibility of fuel-saving and emissions improvement by adjusting fuel-injection signal of the engine control unit (ECU) during engine restart operation was also evaluated. The experimental results showed that the addition of the fuel-injection modulation plus idling-stop strategy can improve the fuel economy rate by up to 12.2% and reduce carbon monoxide (CO) emission by up to 36.95% in comparison with the non-idling stop case.

Sign in / Sign up

Export Citation Format

Share Document