Predicted Performance of an Integrated Solar Thermal and Photovoltaic System With Hybrid Turbine-Fuel Cell Cogeneration System

2008 ◽  
Author(s):  
Gregory J. Kowalski ◽  
Mansour Zenouzi
Keyword(s):  
Carbon Dioxide ◽  
Renewable Energy ◽  
Fuel Cell ◽  
Energy Systems ◽  
Energy Utilization ◽  
Solar Thermal ◽  
System Level ◽  
Energy Requirements ◽  
Cogeneration System ◽  
And Storage

A general approach, the HLRP technique, for determining the performance of a hybrid turbine-fuel cell cogeneration system with a renewable energy sources is presented for a domestic residence. The hybrid-cogeneration system provides the electric power as well as satisfying heating loads. In this paper a system level analysis that includes practical values of heat exchangers, pumps, and storage equipment is presented. The use of the ratio of the thermal load to required power parameter (HLRP), which has been used by the authors to scale energy systems, allows the performance to be quickly determined and preliminary carbon dioxide production rates and cost effects to be estimated. The present paper includes solar energy systems as renewable energy to illustrate the development of this technique and its integration with the hybrid fuel cell cogeneration system. Practical values of solar collector efficiency and storage tank and battery storage efficiency are included. The analysis focused on matching the transient characteristics of the power and thermal loads with those of the renewable energy system. The results demonstrate that for a typical winter day in the location studied there are not large variations in the energy utilization factors for the four different systems investigated. There is a 23% reduction in the carbon dioxide produced using the solar thermal or combined system as compared to the no renewable energy or photovoltaic systems. The information provided by the performance graphs is used to estimate costs for each system and to easily determine which system is the most efficient for satisfying energy requirements and reducing green house gas emissions. The results provide site planners and physical plant operators with initial information that can be used to design new facilities or effectively integrate large plant expansion that include renewable energy systems in a manner that will minimize energy requirements and reduce pollution effects.

Renewable Energy and Hybrid Turbine-Fuel Cell Cogeneration System’s Predicted Performance

2007 ◽  
Author(s):  
Gregory J. Kowalski ◽  
Mansour Zenouzi
Keyword(s):  
Carbon Dioxide ◽  
Renewable Energy ◽  
Fuel Cell ◽  
Energy Systems ◽  
Solar Thermal ◽  
Energy Requirements ◽  
Thermal System ◽  
Cogeneration System ◽  
Solar Thermal System ◽  
And Storage

A normalized, general approach for determining the combined performance of a hybrid turbine-fuel cell cogeneration system with a renewable energy source, such as a solar thermal system is presented. The hybrid-cogeneration system provides required electric power as well as satisfying simultaneous heating loads. In this paper a system level analysis that includes practical values of heat exchangers, pumps, and storage equipment is presented. The use of the ratio of the thermal load to required power parameter (HLRP), which has been previously used by the authors to scale energy systems, allows the performance to be quickly determined and preliminary carbon dioxide production rates and cost effects to be estimated. The present paper will focus on a solar thermal system as renewable energy to illustrate the development of this technique and its integration with the hybrid fuel cell cogeneration system. Practical values of solar collector efficiency and storage tank efficiency are included. The analysis will focus on matching the transient characteristics of the power and thermal loads with those of the renewable energy system. Performance measures used to evaluate the investigated designs include the energy utilization factor and the carbon dioxide produced per unit power output. The information provided by the performance graphs can be used to estimate costs for each system and to easily determine which system is the most efficient for satisfying energy requirements and reducing green house gas emissions. The results provide site planners and physical plant operators with initial information that can be used to design new facilities or effectively integrate large plant expansion that include renewable energy systems in a manner that will minimize energy requirements and reduce pollution effects.

Predicted Performance of an Integrated Solar Thermal and Photovoltaic System With Hybrid Turbine-Fuel Cell Cogeneration System With Cooling Loads

2008 ◽  
Author(s):  
Gregory J. Kowalski ◽  
Mansour Zenouzi
Keyword(s):  
Carbon Dioxide ◽  
Renewable Energy ◽  
Fuel Cell ◽  
Renewable Energy Sources ◽  
Energy Systems ◽  
Energy Utilization ◽  
Photovoltaic System ◽  
Energy Requirements ◽  
Cogeneration System ◽  
Cooling Loads

A general approach, the HLRP technique, for determining the performance of a hybrid turbine-fuel cell cogeneration system with a renewable energy sources is presented for a domestic residence for a summer day with cooling loads. The use of the ratio of the thermal load to required power parameter (HLRP), which scales the energy systems, allows the performance to be quickly determined and preliminary carbon dioxide production rates and cost effects to be estimated. The present paper includes solar energy systems, thermal and photovoltaic, as renewable energy to illustrate the development of this technique and its integration with the hybrid fuel cell cogeneration system. The analysis focused on matching the transient characteristics of the power and thermal loads with those of the renewable energy system. The results demonstrate that for a typical summer day in the location studied there are not large variations in the energy utilization factors for the four different systems investigated. Surprisingly, the photovoltaic system produces the lowest first law performance and the largest amounts of carbon dioxide. This observation points out the complexity of these systems. The explanation illustrates that saving power production while increasing the use of the most inefficient device (the furnace) decreases the system performance. The information provided by the performance graphs is used to estimate costs for each system and to easily determine which system is the most efficient for satisfying energy requirements and reducing green house gas emissions. The results provide site planners and physical plant operators with initial information that can be used to design new facilities or effectively integrate large plant expansion that include renewable energy systems in a manner that will minimize energy requirements and reduce pollution effects.

Design, Installation, and Performance Characterization of a Laboratory-Scale Solar Thermal System for Experiments in Solar Energy Utilization

2012 ◽  
Author(s):  
Stephanie Drozek ◽  
Christopher Damm ◽  
Ryan Enot ◽  
Andrew Hjortland ◽  
Brandon Jackson ◽  
...  
Keyword(s):  
Renewable Energy ◽  
Solar Energy ◽  
Laboratory Scale ◽  
Energy Utilization ◽  
Solar Thermal ◽  
Thermal System ◽  
Performance Characterization ◽  
And Performance ◽  
Solar Thermal System

The purpose of this paper is to describe the implementation of a laboratory-scale solar thermal system for the Renewable Energy Systems Laboratory at the Milwaukee School of Engineering (MSOE). The system development began as a student senior design project where students designed and fabricated a laboratory-scale solar thermal system to complement an existing commercial solar energy system on campus. The solar thermal system is designed specifically for educating engineers. This laboratory equipment, including a solar light simulator, allows for variation of operating parameters to investigate their impact on system performance. The equipment will be utilized in two courses: Applied Thermodynamics, and Renewable Energy Utilization. During the solar thermal laboratories performed in these courses, students conduct experiments based on the American Society of Heating, Refrigeration and Air-Conditioning Engineers (ASHRAE) 93-2010 standard for testing and performance characterization of solar thermal systems. Their measurements are then used to quantify energy output, efficiency and losses of the system and subsystem components.

scholarly journals Optimum Renewable Fraction for Grid-connected Photovoltaic in Office Building Energy Systems in Indonesia

2018 ◽  
Vol 9 (4) ◽  
pp. 1866 ◽  
Author(s):  
Ayong Hiendro ◽  
Ismail Yusuf ◽  
F. Trias Pontia Wigyarianto ◽  
Kho Hie Khwee ◽  
Junaidi Junaidi
Keyword(s):  
Carbon Dioxide ◽  
Renewable Energy ◽  
Energy Systems ◽  
Building Energy ◽  
Office Building ◽  
Pv System ◽  
Optimum Result ◽  
Pv Systems ◽  
Building Energy Systems

<span lang="EN-US">This paper analyzes influences of renewable fraction on grid-connected photovoltaic (PV) for office building energy systems. The fraction of renewable energy has important contributions on sizing the grid-connected PV systems and selling and buying electricity, and hence reducing net present cost (NPC) and carbon dioxide (CO<sub>2</sub>) emission. An optimum result with the lowest total NPC for serving an office building is achieved by employing the renewable fraction of 58%, in which 58% of electricity is supplied from the PV and the remaining 42% of electricity is purchased from the grid. The results have shown that the optimum grid-connected PV system with an appropriate renewable fraction value could greatly reduce the total NPC and CO<sub>2</sub> emission.</span>

Power Electronics and Controls in Solar Photovoltaic Systems

2013 ◽  
pp. 68-125
Author(s):  
Radian Belu
Keyword(s):  
Renewable Energy ◽  
Power Electronics ◽  
Renewable Energy Sources ◽  
Energy Systems ◽  
Solar Thermal ◽  
System Capacity ◽  
Energy Sources ◽  
Solar Panels ◽  
Renewable Energy Systems ◽  
Pv Systems

The use of renewable energy sources is increasingly being pursued as a supplemental and an alternative to traditional energy generation. Several distributed energy systems are expected to a have a significant impact on the energy industry in the near future. As such, the renewable energy systems are presently undergoing a rapid change in technology and use. Such a feature is enabled clearly by power electronics. Both the solar-thermal and photovoltaic (PV) technologies have an almost exponential growth in installed capacity and applications. Both of them contribute to the overall grid control and power electronics research and advancement. Among the renewable energy systems, photovoltaic (PV) systems are the ones that make use of an extended scale of the advanced power electronics technologies. The specification of a power electronics interface is subject to the requirements related not only to the renewable energy source itself but also to its effects on the operations of the systems on which it is connected, especially the ones where these intermittent energy sources constitute a significant part of the total system capacity. Power electronics can also play a significant role in enhancing the performance and efficiency of PV systems. Furthermore, the use of appropriate power electronics enables solar generated electricity to be integrated into power grid. Aside from improving the quality of solar panels themselves, power electronics can provide another means of improving energy efficiency in PV and solar-thermal energy systems.

Power Electronics and Controls in Solar Photovoltaic Systems

2015 ◽  
pp. 2016-2072
Author(s):  
Radian Belu
Keyword(s):  
Renewable Energy ◽  
Power Electronics ◽  
Renewable Energy Sources ◽  
Energy Systems ◽  
Solar Thermal ◽  
System Capacity ◽  
Energy Sources ◽  
Solar Panels ◽  
Renewable Energy Systems ◽  
Pv Systems

The use of renewable energy sources is increasingly being pursued as a supplemental and an alternative to traditional energy generation. Several distributed energy systems are expected to a have a significant impact on the energy industry in the near future. As such, the renewable energy systems are presently undergoing a rapid change in technology and use. Such a feature is enabled clearly by power electronics. Both the solar-thermal and photovoltaic (PV) technologies have an almost exponential growth in installed capacity and applications. Both of them contribute to the overall grid control and power electronics research and advancement. Among the renewable energy systems, photovoltaic (PV) systems are the ones that make use of an extended scale of the advanced power electronics technologies. The specification of a power electronics interface is subject to the requirements related not only to the renewable energy source itself but also to its effects on the operations of the systems on which it is connected, especially the ones where these intermittent energy sources constitute a significant part of the total system capacity. Power electronics can also play a significant role in enhancing the performance and efficiency of PV systems. Furthermore, the use of appropriate power electronics enables solar generated electricity to be integrated into power grid. Aside from improving the quality of solar panels themselves, power electronics can provide another means of improving energy efficiency in PV and solar-thermal energy systems.

scholarly journals Multi-Objective Decision-Making for Hybrid Renewable Energy Systems for Cities: A Case Study of Xiongan New District in China

Energies ◽  
2020 ◽  
Vol 13 (23) ◽  
pp. 6223
Author(s):  
Bin Ye ◽  
Minhua Zhou ◽  
Dan Yan ◽  
Yin Li
Keyword(s):  
Decision Making ◽  
Renewable Energy ◽  
Energy Systems ◽  
Energy System ◽  
Energy Utilization ◽  
Target Area ◽  
Renewable Energy Systems ◽  
Multi Objective ◽  
Hybrid Renewable Energy Systems ◽  
Hybrid Renewable Energy

The application of renewable energy has become increasingly widespread worldwide because of its advantages of resource abundance and environmental friendliness. However, the deployment of hybrid renewable energy systems (HRESs) varies greatly from city to city due to large differences in economic endurance, social acceptance and renewable energy endowment. Urban policymakers thus face great challenges in promoting local clean renewable energy utilization. To address these issues, this paper proposes a combined multi-objective optimization method, and the specific process of this method is described as follows. The Hybrid Optimization Model for electric energy was first used to examine five different scenarios of renewable energy systems. Then, the Technique for Order Preference by Similarity to an Ideal Solution was applied using eleven comprehensive indicators to determine the best option for the target area using three different weights. To verify the feasibility of this method, Xiongan New District (XND) was selected as an example to illustrate the process of selecting the optimal HRES. The empirical results of simulation tools and multi-objective decision-making show that the Photovoltaic-Diesel-Battery off-grid energy system (option III) and PV-Diesel-Hydrogen-Battery off-grid energy system (option V) are two highly feasible schemes for an HRES in XND. The cost of energy for these two options is 0.203 and 0.209 $/kWh, respectively, and the carbon dioxide emissions are 14,473 t/yr and 345 t/yr, respectively. Our results provide a reference for policymakers in deploying an HRES in the XND area.

scholarly journals The Role of Trade Liberalization in Carbon Dioxide Emission: Evidence From Heterogeneous Panel Estimations

2019 ◽  
Vol 10 (5) ◽  
pp. 228
Author(s):  
Gholamreza Zandi ◽  
Muhammad Haseeb
Keyword(s):  
Carbon Dioxide ◽  
Developing Countries ◽  
Renewable Energy ◽  
Trade Liberalization ◽  
Causal Relationship ◽  
Environmental Degradation ◽  
Carbon Dioxide Emission ◽  
Energy Utilization ◽  
Long Run ◽  
Heterogeneous Panel

In the present globalized world, production forms are progressively divided across nations. Consequently, domestic consumption in one nation is progressively fulfilled by worldwide supply chains. This spectacle has pulled policy and widespread intellectual discussions on the assignment of greenhouse gas (GHG) emanations, especially carbon dioxide (CO2) emission; these are accountabilities connected to global trade since worldwide trade causes net carbon dioxide emission. The aim of the present study is to examine the impact of trade liberalization on carbon dioxide emission. We used the panel data of 105 developed and developing countries from 1990 to 2017. The results of FMOLS and DOLS confirm that all variables are connected in the long-run period. The results of long run coefficient confirm that that the trade liberalization has a positive effect on environmental degradation and cause to increase environmental degradation. Likewise, economic growth and energy consumption has also a positive and significant impact on environmental degradation. However, we find an evidence of negative and significant impact of renewable energy utilization on environmental degradation. Finally, the results of heterogeneous panel causality confirm that there is a uni-directional causal relationship between trade liberalization and environmental degradation where causality is running from trade liberalization to environmental degradation. However, we find a bi-directional causal relationship of environmental degradation with energy utilization and renewable energy utilization in all selected developed and developing countries.

Sign in / Sign up

Export Citation Format

Share Document