Design and Experimental Verification of Torsion-Bending Low-Frequency Piezoelectric Energy Harvesters

2016 ◽  
Author(s):  
Hichem Abdelmoula ◽  
Nathan Sharpes ◽  
Hyeon Lee ◽  
Abdessattar Abdelkefi ◽  
Shashank Priya
Keyword(s):  
System Analysis ◽  
Energy Harvester ◽  
Excitation Frequency ◽  
Low Frequency ◽  
Load Resistance ◽  
Mode Shapes ◽  
Low Frequencies ◽  
Piezoelectric Energy ◽  
The Masses ◽  
Tip Mass

We design and experimentally validate a zigzag piezoelectric energy harvester that can generate energy at low frequencies and which can be used to operate low-power consumption electronic devices. The harvester is composed of metal and piezoelectric layers and is used to harvest energy through direct excitations. A computational model is developed using Abaqus to determine the exact mode shapes and coupled frequencies of the considered energy harvester in order to design a broadband torsion-bending mechanical system. Analysis is then performed to determine the optimal load resistance. The computational results are compared and validated with the experimental measurements. More detailed analysis is then carried out to investigate the effects of the masses on the bending and torsion natural frequencies of the harvester and generated power levels. The results show that due to the coupling between the bending and torsion modes of the zigzag structure, highest levels of the harvested power are obtained when the excitation frequency matches the coupled frequency of torsion type for three different values of the tip mass.

scholarly journals Split Cantilever Multi-Resonant Piezoelectric Energy Harvester for Low-Frequency Application

Energies ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 5077
Author(s):  
David Omooria Masara ◽  
Hassan El Gamal ◽  
Ossama Mokhiamar
Keyword(s):  
Energy Harvester ◽  
Low Frequency ◽  
Load Resistance ◽  
High Energy ◽  
The Finite Element Method ◽  
Fundamental Frequencies ◽  
Piezoelectric Energy ◽  
Wide Range ◽  
Bending Modes ◽  
Tip Mass

This paper presents a new way to design a broadband harvester for harvesting high energy over a low-frequency range of 10–15 Hz. The design comprises a cantilever beam with two parallel grooves to form three dissimilar length parallel branches, each with an unequal concentrated tip mass. The piezoelectric material covers the whole length on both sides of the beam to form a bimorph. Appropriate geometry and mass magnitudes are obtained by a parametric study using the Finite Element Method. The design was simulated in COMSOL Multiphysics to study its response. The first three bending modes were utilized in energy harvesting, resulting in three power peaks at their respective fundamental frequencies. The adequate load resistance determined was 5.62 kΩ, at which maximum power can be harvested. The proposed harvester was compared to two other harvesters presented in the literature for validation: First, an optimized conventional harvester while the proposed harvester is operating at adequate load resistance. Second, a multimodal harvester, while the proposed harvester is operating at a 10 kΩ load. The suggested harvester proved to be more efficient by harvesting sufficiently higher broadband energy and is applicable in a wide range of vibration environments because of its adaptability in design.

scholarly journals Analysis of a Cantilevered Piezoelectric Energy Harvester in Different Orientations for Rotational Motion

Sensors ◽  
2020 ◽  
Vol 20 (4) ◽  
pp. 1206 ◽  
Author(s):  
Wei-Jiun Su ◽  
Jia-Han Lin ◽  
Wei-Chang Li
Keyword(s):  
Theoretical Model ◽  
Resonant Frequency ◽  
Rotational Motion ◽  
Axial Load ◽  
Energy Harvester ◽  
Excitation Frequency ◽  
Experimental Studies ◽  
Piezoelectric Energy ◽  
Piezoelectric Cantilever ◽  
Tip Mass

This paper investigates a piezoelectric energy harvester that consists of a piezoelectric cantilever and a tip mass for horizontal rotational motion. Rotational motion results in centrifugal force, which causes the axial load on the beam and alters the resonant frequency of the system. The piezoelectric energy harvester is installed on a rotational hub in three orientations—inward, outward, and tilted configurations—to examine their influence on the performance of the harvester. The theoretical model of the piezoelectric energy harvester is developed to explain the dynamics of the system and experiments are conducted to validate the model. Theoretical and experimental studies are presented with various tilt angles and distances between the harvester and the rotating center. The results show that the installation distance and the tilt angle can be used to adjust the resonant frequency of the system to match the excitation frequency.

Heartbeat Energy Harvesting Using the Fan-Folded Piezoelectric Beam Geometry

2015 ◽  
Author(s):  
M. H. Ansari ◽  
M. Amin Karami
Keyword(s):  
Natural Frequency ◽  
Energy Harvester ◽  
Low Frequency ◽  
Mode Shapes ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Mechanical Coupling ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Piezoelectric Beam

A three dimensional piezoelectric vibration energy harvester is designed to generate electricity from heartbeat vibrations. The device consists of several bimorph piezoelectric beams stacked on top of each other. These horizontal bimorph beams are connected to each other by rigid vertical beams making a fan-folded geometry. One end of the design is clamped and the other end is free. One major problem in micro-scale piezoelectric energy harvesters is their high natural frequency. The same challenge is faced in development of a compact vibration energy harvester for the low frequency heartbeat vibrations. One way to decrease the natural frequency is to increase the length of the bimorph beam. This approach is not usually practical due to size limitations. By utilizing the fan-folded geometry, the natural frequency is decreased while the size constraints are observed. The required size limit of the energy harvester is 1 cm by 1 cm by 1 cm. In this paper, the natural frequencies and mode shapes of fan-folded energy harvesters are analytically derived. The electro-mechanical coupling has been included in the model for the piezoelectric beam. The design criteria for the device are discussed.

scholarly journals An Exact Analytical Solution to Exponentially Tapered Piezoelectric Energy Harvester

2015 ◽  
Vol 2015 ◽  
pp. 1-13 ◽  
Author(s):  
H. Salmani ◽  
G. H. Rahimi ◽  
S. A. Hosseini Kordkheili
Keyword(s):  
Analytical Solution ◽  
Energy Harvester ◽  
Exact Analytical Solution ◽  
Mode Shapes ◽  
Electric Resistance ◽  
Coupled Equations ◽  
Piezoelectric Energy ◽  
Piezoelectric Beam ◽  
Parallel Connections ◽  
Tip Mass

It has been proven that tapering the piezoelectric beam through its length optimizes the power extracted from vibration based energy harvesting. This phenomenon has been investigated by some researchers using semianalytical, finite element and experimental methods. In this paper, an exact analytical solution is presented to calculate the power generated from vibration of exponentially tapered unimorph and bimorph with series and parallel connections. The mass normalized mode shapes of the exponentially tapered piezoelectric beam with tip mass are implemented to transfer the proposed electromechanical coupled equations into modal coordinates. The steady states harmonic solution results are verified both numerically and experimentally. Results show that there exist values for tapering parameter and electric resistance in a way that the output power per mass of the energy harvester will be maximized. Moreover it is concluded that the electric resistance must be higher than a specified value for gaining more power by tapering the beam.

scholarly journals On the Efficiency of a Piezoelectric Energy Harvester under Combined Aeroelastic and Base Excitation

Micromachines ◽  
2021 ◽  
Vol 12 (8) ◽  
pp. 962
Author(s):  
Antiopi-Malvina Stamatellou ◽  
Anestis I. Kalfas
Keyword(s):  
Conversion Efficiency ◽  
Power Output ◽  
Polyvinylidene Fluoride ◽  
Energy Harvester ◽  
Excitation Frequency ◽  
Elastic Strain Energy ◽  
Rate Of Change ◽  
Mode Shapes ◽  
Base Excitation ◽  
Piezoelectric Energy

A flutter-type, nonlinear piezoelectric energy harvester was tested in various combinations of aerodynamic and harmonic base excitation to study its power output and efficiency. The commercial polyvinylidene fluoride film transducer LDT1-028K was used in 33 excitation mode. The aerodynamic excitation was created by a centrifugal fan and the base excitation by a cone speaker. The excitations were produced by varying independently the mean airflow velocity and the frequency of base vibration. A capacitive load was used to store the harvested energy. A line laser was employed along with long exposure photography and high-speed video, for the visualization of the piezo film’s mode shapes and the measurement of maximum tip deflection. The harvested power was mapped along with the maximum tip deflection of the piezo-film, and a process of optimally combining the two excitation sources for maximum power harvesting is demonstrated. The energy conversion efficiency is defined by means of electrical power output divided by the elastic strain energy rate of change during oscillations. The efficiency was mapped and correlated with resonance conditions and results from other studies. It was observed that the conversion efficiency is related to the phase difference between excitation and response and tends to decrease as the excitation frequency rises.

Modeling and Performance Enhancement of Low-Frequency Energy Harvesters

2018 ◽  
pp. 826-862
Author(s):  
Abdessattar Abdelkefi
Keyword(s):  
Performance Enhancement ◽  
Mechanical Energy ◽  
Excitation Frequency ◽  
Low Frequency ◽  
Ocean Waves ◽  
Sensors And Actuators ◽  
Low Frequencies ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
And Performance

There exist numerous low-frequency excitation sources, such as walking, breathing, and ocean waves, capable of providing viable amounts of mechanical energy to power many critical devices, including pacemakers, cell phones, MEMS devices, wireless sensors, and actuators. Harvesting significant energy levels from such sources can only be achieved through the design of devices capable of performing effective energy transfer mechanisms over low frequencies. In this chapter, two concepts of efficient low-frequency piezoelectric energy harvesters are presented, namely, variable-shaped piezoelectric energy harvesters and piezomagnetoelastic energy harvesters. Linear and nonlinear electromechanical models are developed and validated in this chapter. The results show that the quadratic shape can yield up to two times the energy harvested by a rectangular one. It is also demonstrated that depending on the available excitation frequency, an enhanced energy harvester can be tuned and optimized by changing the length of the piezoelectric material or by changing the distance between the two tip magnets.

scholarly journals Modeling and Analysis of Upright Piezoelectric Energy Harvester under Aerodynamic Vortex-induced Vibration

Micromachines ◽  
2018 ◽  
Vol 9 (12) ◽  
pp. 667 ◽  
Author(s):  
Jinda Jia ◽  
Xiaobiao Shan ◽  
Deepesh Upadrashta ◽  
Tao Xie ◽  
Yaowen Yang ◽  
...  
Keyword(s):  
Energy Harvester ◽  
Beam Theory ◽  
Longitudinal Direction ◽  
Load Resistance ◽  
Vortex Induced Vibration ◽  
Modeling And Analysis ◽  
Coupled Equations ◽  
Output Performance ◽  
Piezoelectric Energy ◽  
Tip Mass

This paper presents an upright piezoelectric energy harvester (UPEH) with cylinder extension along its longitudinal direction. The UPEH can generate energy from low-speed wind by bending deformation produced by vortex-induced vibrations (VIVs). The UPEH has the advantages of less working space and ease of setting up an array over conventional vortex-induced vibration harvesters. The nonlinear distributed modeling method is established based on Euler–Bernoulli beam theory and aerodynamic vortex-induced force of the cylinder is obtained by the van der Pol wake oscillator theory. The fluid–solid–electricity governing coupled equations are derived using Lagrange’s equation and solved through Galerkin discretization. The effect of cylinder gravity on the dynamic characteristics of the UPEH is also considered using the energy method. The influences of substrate dimension, piezoelectric dimension, the mass of cylinder extension, and electrical load resistance on the output performance of harvester are studied using the theoretical model. Experiments were carried out and the results were in good agreement with the numerical results. The results showed that a UPEH configuration achieves the maximum power of 635.04 μW at optimum resistance of 250 kΩ when tested at a wind speed of 4.20 m/s. The theoretical results show that the UPEH can get better energy harvesting output performance with a lighter tip mass of cylinder, and thicker and shorter substrate in its synchronization working region. This work will provide the theoretical guidance for studying the array of multiple upright energy harvesters.

Modeling and Performance Enhancement of Low-Frequency Energy Harvesters

2015 ◽  
pp. 159-196 ◽  
Author(s):  
Abdessattar Abdelkefi
Keyword(s):  
Performance Enhancement ◽  
Mechanical Energy ◽  
Excitation Frequency ◽  
Low Frequency ◽  
Ocean Waves ◽  
Sensors And Actuators ◽  
Low Frequencies ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
And Performance

There exist numerous low-frequency excitation sources, such as walking, breathing, and ocean waves, capable of providing viable amounts of mechanical energy to power many critical devices, including pacemakers, cell phones, MEMS devices, wireless sensors, and actuators. Harvesting significant energy levels from such sources can only be achieved through the design of devices capable of performing effective energy transfer mechanisms over low frequencies. In this chapter, two concepts of efficient low-frequency piezoelectric energy harvesters are presented, namely, variable-shaped piezoelectric energy harvesters and piezomagnetoelastic energy harvesters. Linear and nonlinear electromechanical models are developed and validated in this chapter. The results show that the quadratic shape can yield up to two times the energy harvested by a rectangular one. It is also demonstrated that depending on the available excitation frequency, an enhanced energy harvester can be tuned and optimized by changing the length of the piezoelectric material or by changing the distance between the two tip magnets.

Modeling and Analysis of a Piezoelectric Energy Scavenger for Rotary Motion Applications

2010 ◽  
Vol 133 (1) ◽  
Author(s):  
F. Khameneifar ◽  
M. Moallem ◽  
S. Arzanpour
Keyword(s):  
Energy Harvester ◽  
Equations Of Motion ◽  
Quantitative Description ◽  
Load Resistance ◽  
Rotary Motion ◽  
Flexible Beam ◽  
Modeling And Analysis ◽  
Piezoelectric Energy ◽  
Tip Mass ◽  
Energy Scavenger

This paper presents modeling and analysis of a piezoelectric mounted rotary flexible beam that can be used as an energy scavenger for rotary motion applications. The energy harvester system consists of a piezoelectric bimorph cantilever beam with a tip mass mounted on a rotating hub. Assuming Euler–Bernoulli beam equations and considering the effect of a piezoelectric transducer, equations of motion are derived using the Lagrangian approach followed by relationships describing the harvested power. The equations provide a quantitative description of how the hub acceleration and gravity due to the tip mass contribute power to the energy harvester. In particular, expressions describing optimum load resistance and the maximum power that can be harvested using the proposed system are derived. Numerical simulations are performed to show the performance of the harvester by obtaining tip velocities and electrical output voltages for a range of electrical load resistances and rotational speeds. It is shown that by proper sizing and parameter selection, the proposed system can supply enough energy for operating wireless sensors in rotating mechanisms such as tires and turbines.

Energy Harvesting From Heartbeat Using Piezoelectric Beams With Fan-Folded Configuration and Added Tip Mass

2015 ◽  
Author(s):  
M. H. Ansari ◽  
M. Amin Karami
Keyword(s):  
Natural Frequency ◽  
Energy Harvester ◽  
Mode Shapes ◽  
Mechanical Coupling ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Power Frequency ◽  
Tip Mass ◽  
Multi Mode ◽  
Very High

A fan-folded piezoelectric energy harvester is designed to generate electricity using heartbeat vibrations. This energy harvester consists of several bimorph beams stacked on top of each other making a fan-folded shape. Each beam has a brass substrate and two piezoelectric patches attached on both sides of it. These beams are connected to each other by rigid beams. One end of the device is clamped to the wall and the other end is free to vibrate. A tip mass is placed at the free end to enhance the output power of the device and reduce the natural frequency of the system. High natural frequency is one major concern about the microscaled energy harvesters. The size for this energy harvester is 1 cm by 1 cm by 1 cm, which makes the natural frequency very high. By utilizing the fan-folded geometry and adding tip mass and link mass to the configuration, this natural frequency is reduced to the desired range. The generated electricity can be used to power up a pacemaker. If enough electricity is generated, the pacemaker operates without having a battery and the patient does not need to have a surgery every seven to ten years to have the battery replaced. The power needed for a pacemaker to operate is about 1 microwatt. In this paper, the natural frequencies and mode shapes of fan-folded energy harvesters with added tip mass and link mass are analytically derived. The electro-mechanical coupling has been included in the model and the expression for the multi-mode power frequency response function is calculated.

Sign in / Sign up

Export Citation Format

Share Document