ROM of Primary Resonance Amplitude-Voltage Response of MEMS Cantilevers

2013 ◽  
Author(s):  
Dumitru I. Caruntu ◽  
Le Luo ◽  
Israel Martinez ◽  
Mostafa Fathelden ◽  
Christian Reyes
Keyword(s):  
Parametric Excitation ◽  
Constant Width ◽  
Primary Resonance ◽  
Reduced Order Model ◽  
Thickness Variation ◽  
Voltage Response ◽  
Order Model ◽  
Resonance Amplitude ◽  
Reduced Order ◽  
Mems Cantilevers

This paper uses Reduced Order Model (ROM) method to investigate the amplitude-voltage response of MEMS cantilever resonators of linear thickness variation and constant width under AC voltage of frequency near half natural frequency of the resonator. The influences of nonlinearities resulting from AC voltage parametric excitation on the response of the structure are reported.

The Static and Dynamic Behavior of MEMS Arches Under Electrostatic Actuation

2009 ◽  
Author(s):  
Hassen M. Ouakad ◽  
Mohammad I. Younis ◽  
Fadi M. Alsaleem ◽  
Ronald Miles ◽  
Weili Cui
Keyword(s):  
Multiple Scales ◽  
Perturbation Technique ◽  
Dynamical Behavior ◽  
Primary Resonance ◽  
Reduced Order Model ◽  
Harmonic Load ◽  
Order Model ◽  
Reduced Order ◽  
Electrostatically Actuated ◽  
Model Equations

In this paper, we investigate theoretically and experimentally the static and dynamic behaviors of electrostatically actuated clamped-clamped micromachined arches when excited by a DC load superimposed to an AC harmonic load. A Galerkin based reduced-order model is used to discretize the distributed-parameter model of the considered shallow arch. The natural frequencies of the arch are calculated for various values of DC voltages and initial rises of the arch. The forced vibration response of the arch to a combined DC and AC harmonic load is determined when excited near its fundamental natural frequency. For small DC and AC loads, a perturbation technique (the method of multiple scales) is also used. For large DC and AC, the reduced-order model equations are integrated numerically with time to get the arch dynamic response. The results show various nonlinear scenarios of transitions to snap-through and dynamic pull-in. The effect of rise is shown to have significant effect on the dynamical behavior of the MEMS arch. Experimental work is conducted to test polysilicon curved microbeam when excited by DC and AC loads. Experimental results on primary resonance and dynamic pull-in are shown and compared with the theoretical results.

Reduced Order Model of Electrostatically Actuated Carbon Nanotube Cantilever Biosensors for Primary Resonance

2013 ◽  
Author(s):  
Dumitru I. Caruntu ◽  
Le Luo
Keyword(s):  
Multiple Scales ◽  
Van Der Waals ◽  
Primary Resonance ◽  
Reduced Order Model ◽  
Mass Detection ◽  
Order Model ◽  
Reduced Order ◽  
Electrostatically Actuated ◽  
Carbon Nano Tubes ◽  
Ground Plate

This paper investigates electrostatically actuated Carbon Nano-Tubes (CNT) cantilevers biosensors using the Reduced Order Model (ROM) method. Forces acting on the CNT are electrostatic, damping, and van der Waals. The electrostatic actuation is given by soft AC voltage. Van der Waals forces are significant for gaps between the CNT and a ground plate lower than 100 nm. Both forces electrostatic and van der Waals are nonlinear. CNT undergoes nonlinear parametric dynamics. ROM is used to investigate the system under soft excitations and/or weak nonlinearities. The frequency-amplitude response is found in the case of primary resonance and compared to the Method of Multiple Scales (MMS). The CNT biosensor is to be used for mass detection applications.

ROM of Primary Resonance of Electrostatically Actuated MEMS/NEMS Plates

2014 ◽  
Author(s):  
Dumitru I. Caruntu ◽  
Reynaldo Oyervides
Keyword(s):  
Casimir Force ◽  
Van Der Waals ◽  
Primary Resonance ◽  
Voltage Response ◽  
Voltage Amplitude ◽  
Circular Plates ◽  
Order Model ◽  
Amplitude Response ◽  
Reduced Order ◽  
Electrostatically Actuated

This paper utilizes Reduced Order Model (ROM) method to investigate the voltage-amplitude response of electrostatically actuated M/NEMS clamped circular plates. Soft AC voltage at frequency near half natural frequency of the plate is used. This results in primary resonance of the system. The effects of nonlinearities of the system including pull-in instability on the voltage-amplitude response are investigated. Namely, the effects of detuning frequency, damping, Casimir force, and van der Waals force on the voltage response of clamped circular plates are reported. Casimir and van der Waals forces are found to have significant effects on the response of clamped circular plates and must be considered to accurately model and predict the behavior of the system.

Sign in / Sign up

Export Citation Format

Share Document