scholarly journals Investigation of the Heat Transfer in Cylindrical Receiver Configurations With Inner Tubes

1979 ◽  
Author(s):  
K. Bammert ◽  
R. Krapp ◽  
P. Seifert
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Pressure Loss ◽  
Closed Cycle ◽  
Medium Pressure ◽  
Working Medium

The design of a receiver for a closed-cycle gas turbine with air as the working medium is discussed. The emphasis of the investigations is layed upon the optimization of heat transfer to the working medium. The irradiation pattern along the tubes and the effects of the working-medium pressure, the pressure loss and the tube cage geometry are considered.

Build Direction Effects on Additively Manufactured Channels

2015 ◽  
Author(s):  
Jacob C. Snyder ◽  
Curtis K. Stimpson ◽  
Karen A. Thole ◽  
Dominic Mongillo
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Pressure Loss ◽  
Small Scale ◽  
Turbine Cooling ◽  
Gas Turbine Cooling ◽  
Gas Turbine Heat Transfer ◽  
Manufacturing Techniques ◽  
Traditional Manufacturing

With the advances of Direct Metal Laser Sintering (DMLS), also generically referred to as additive manufacturing, novel geometric features of internal channels for gas turbine cooling can be achieved beyond those features using traditional manufacturing techniques. There are many variables, however, in the DMLS process that affect the final quality of the part. Of most interest to gas turbine heat transfer designers are the roughness levels and tolerance levels that can be held for the internal channels. This study investigates the effect of DMLS build direction and channel shape on the pressure loss and heat transfer measurements of small scale channels. Results indicate that differences in pressure loss occur between the test cases with differing channel shapes and build directions, while little change is measured in heat transfer performance.

Conceptual Design and Cooling Blade Development of 1700°C Class High-Temperature Gas Turbine

2005 ◽  
Vol 127 (2) ◽  
pp. 358-368 ◽  
Author(s):  
Shoko Ito ◽  
Hiroshi Saeki ◽  
Asako Inomata ◽  
Fumio Ootomo ◽  
Katsuya Yamashita ◽  
...  
Keyword(s):  
Heat Transfer ◽  
High Temperature ◽  
Gas Turbine ◽  
Conceptual Design ◽  
Thermal Efficiency ◽  
Internal Cooling ◽  
Closed Cycle ◽  
Steam Consumption ◽  
Flow Phenomena ◽  
High Temperature Gas

In this paper we describe the conceptual design and cooling blade development of a 1700°C-class high-temperature gas turbine in the ACRO-GT-2000 (Advanced Carbon Dioxide Recovery System of Closed-Cycle Gas Turbine Aiming 2000 K) project. In the ACRO-GT closed cycle power plant system, the thermal efficiency aimed at is more than 60% of the higher heating value of fuel (HHV). Because of the high thermal efficiency requirement, the 1700°C-class high-temperature gas turbine must be designed with the minimum amount of cooling and seal steam consumption. The hybrid cooling scheme, which is a combination of closed loop internal cooling and film ejection cooling, was chosen from among several cooling schemes. The elemental experiments and numerical studies, such as those on blade surface heat transfer, internal cooling channel heat transfer, and pressure loss and rotor coolant passage distribution flow phenomena, were conducted and the results were applied to the conceptual design advancement. As a result, the cooling steam consumption in the first stage nozzle and blade was reduced by about 40% compared with the previous design that was performed in the WE-NET (World Energy Network) Phase-I.

Highlights and Future Development of Closed-Cycle Gas Turbines

1974 ◽  
Vol 96 (4) ◽  
pp. 342-348 ◽  
Author(s):  
K. Bammert ◽  
J. Rurik ◽  
H. Griepentrog
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Closed Cycle ◽  
Combined Application ◽  
Central Heating ◽  
Working Medium ◽  
High Temperature Reactor ◽  
The Moment ◽  
New Applications ◽  
Design Construction

At the moment the closed-cycle gas turbine attracts considerable attention due to: 1 The possibility of directly coupling the closed-cycle gas turbine with a gas-cooled high temperature reactor; 2 the economical use of dry coolers to reduce the thermal charge of the environment; and 3 the reduction of pollution and energy consumption, by replacing the domestic hearth by a central heating and power station. The experience gained in the development, design, construction and operation of the closed-cycle gas turbines at present in service is to be used for these new applications. In this paper, four closed-cycle gas turbine plants in operation in Europe are described and the experience obtained is summarized. The incorporation of the experience gained with these plants in the design and construction of future closed-cycle gas turbines using helium as a working medium is shown with the example of a 50 MW helium turbine. The combined application of experience and a new design philosophy results in a rather unconventional gas turbine.

Tube Stresses in the Radiation Part of Solar Receivers and of Conventionally Fired Heaters

1981 ◽  
Author(s):  
K. Bammert ◽  
P. Seifert
Keyword(s):  
Heat Flux ◽  
Power Plant ◽  
Gas Turbine ◽  
Stress Pattern ◽  
Plastic Behavior ◽  
Solar Power Plant ◽  
Closed Cycle ◽  
Tube Material ◽  
Mechanical Loads ◽  
Working Medium

The tubes for the receiver of a solar power plant are designed taking into account thermal and mechanical loads. The receiver transfers 60 MW of heat to the working medium of a closed cycle gas turbine, the medium being air. It is shown how the stress pattern in the tubes are influenced by the distribution of the locally absorbed heat flux, assuming linearly elastic deformation of the tube material. Criteria for the influence of the partially plastic behavior of the tubes are discussed for different distributions of the intensity of the absorbed heat flux.

Effects of Geometry, Spacing, and Number of Pin Fins in Additively Manufactured Microchannel Pin Fin Arrays

2017 ◽  
Vol 140 (1) ◽  
Author(s):  
Katharine K. Ferster ◽  
Kathryn L. Kirsch ◽  
Karen A. Thole
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Pressure Loss ◽  
Reynolds Numbers ◽  
Turbine Engine ◽  
Pin Fin ◽  
Study Results ◽  
Pin Fins ◽  
Turbine Airfoils ◽  
Pin Fin Arrays

The demand for higher efficiency is ever present in the gas turbine field and can be achieved through many different approaches. While additively manufactured parts have only recently been introduced into the hot section of a gas turbine engine, the manufacturing technology shows promise for more widespread implementation since the process allows a designer to push the limits on capabilities of traditional machining and potentially impact turbine efficiencies. Pin fins are conventionally used in turbine airfoils to remove heat from locations in which high thermal and mechanical stresses are present. This study employs the benefits of additive manufacturing to make uniquely shaped pin fins, with the goal of increased performance over conventional cylindrical pin fin arrays. Triangular, star, and spherical shaped pin fins placed in microchannel test coupons were manufactured using direct metal laser sintering (DMLS). These coupons were experimentally investigated for pressure loss and heat transfer at a range of Reynolds numbers. Spacing, number of pin fins in the array, and pin fin geometry were variables that changed pressure loss and heat transfer in this study. Results indicate that the additively manufactured triangles and cylinders outperform conventional pin fin arrays, while stars and dimpled spheres did not.

Heat Transfer Enhancement due to Combination of Dimples, Protrusions, and Ribs in Narrow Internal Passage of Gas Turbine Blade

2011 ◽  
Author(s):  
Akira Murata ◽  
Satomi Nishida ◽  
Hiroshi Saito ◽  
Kaoru Iwamoto ◽  
Yoji Okita ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Heat Transfer Enhancement ◽  
Gas Turbine ◽  
Pressure Loss ◽  
Oblique Line ◽  
Leading Edge ◽  
Inlet Temperature ◽  
Transfer Enhancement ◽  
Narrow Passage

Internal convective cooling of gas-turbine airfoil is essential because turbine inlet temperature becomes higher for pursuing higher thermal efficiency. For higher cooling performance, heat transfer is often enhanced by installing ribs and/or pin-fins in the internal passage. In this study, in order to enhance heat transfer, the combination of spherical dimples, cylindrical protrusions, and transverse square ribs was applied to one wall of a narrow passage. As for the cylindrical protrusions, two different diameter cases were examined. The heat transfer enhancement was measured by a transient infrared thermography method for the Reynolds number of 2,000, 6,000, and 10,000. The pressure loss was also measured in the experiments, and RANS simulation was performed to give a rationale for the experimental results. The present results clearly showed the spatial variation of the local Nusselt number: the high Nusselt number was observed on the rib top-surface and also near the leading edge on the protrusion top-surface. In addition, the areas around the dimple’s trailing-edge on the oblique line connecting the neighbor dimples showed moderately enhanced heat transfer. When two different protrusion-diameter cases were compared, both the mean Nusselt number and the friction factor were similarly higher in the larger protrusion case than the smaller protrusion case, and therefore the larger protrusion case was more effective in cooling even when the pressure loss was taken into account.

Trailing Edge Cooling of Gas Turbine Airfoil Using Blockages With Straight and Inclined Holes

2014 ◽  
Author(s):  
Sin Chien Siw ◽  
Minking K. Chyu ◽  
Mary Anne Alvin
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Pressure Loss ◽  
Heat Transfer Performance ◽  
Experimental Studies ◽  
Internal Cooling ◽  
Transfer Performance ◽  
Trailing Edge ◽  
High Heat Transfer ◽  
Baseline Case

This paper describes the detailed experimental studies of heat transfer enhancement and pressure loss characteristics internal cooling passages using single, double and triple blockages equipped with straight and inclined holes. The blockage consist of 7 holes with the diameter, D = 6.35mm, which is 0.5 of the height of the channel. Three different hole inclination angles ranging from 0°, 15° and 30° from the horizontal plane are explored. The case with straight holes (0°) is considered as baseline case, while the cases with inclined holes are introduced to enhance heat transfer performance. The transient liquid crystal technique is employed to deduce the heat transfer coefficient on the internal cooling channel, while the pressure loss of the entire channel is measured using pressure taps connected to the digital manometer. Numerical analysis is later performed using ANSYS CFX, based on the shear stress turbulence (SST) model to provide detailed insights about the flow field in the channel, which explains the heat transfer phenomena caused by varying the hole inclination angle. The heat transfer performance of the blockages is higher than conventional configuration using vortex generators, i.e., pin-fins by approximately two folds, while accompanied by much higher pressure loss. The proposed inclined holes array exhibits more effective impingement effects resulted in a substantial cooling performance compared to the baseline case by approximately 50%. This design can be applicable to the trailing edge of gas turbine airfoils, which can provide high heat transfer rate and pressure loss from repeated significant area contractions.

Heat Transfer in a Rotating, Blade-Shaped, Two-Pass Cooling Channel With a Variable Aspect Ratio

2021 ◽  
Author(s):  
I-Lun Chen ◽  
Izzet Sahin ◽  
Lesley M. Wright ◽  
Je-Chin Han ◽  
Robert Krewinkel
Keyword(s):  
Heat Transfer ◽  
Aspect Ratio ◽  
Gas Turbine ◽  
Cross Section ◽  
Pressure Loss ◽  
Planar Geometry ◽  
Internal Cooling ◽  
Cooling Channel ◽  
First Passage ◽  
Rotating Blade

Abstract This study features a rotating, blade-shaped, two-pass cooling channel with a variable aspect ratio. Internal cooling passages of modern gas turbine blades closely follow the shape and contour of the airfoils. Therefore, the cross-section and the orientation with respect to rotation varies for each cooling channel. The effect of passage orientation on the heat transfer and pressure loss is investigated by comparing to a planar channel design with a similar geometry. Following the blade cross-section, the first pass of the serpentine channel is angled at 50° from the direction of rotation while the second pass has an orientation angle of 105°. The coolant flows radially outward in the first passage with an aspect ratio (AR) = 4:1. After a 180-degree tip turn, the coolant travels radially inward into the second passage with AR = 2:1. The copper plate method is applied to obtain the regionally-averaged heat transfer coefficients on all the interior walls of the cooling channel. In addition to the smooth surface case, 45° angled ribs with a profiled cross section are also placed on the leading and trailing surfaces in both the passages. The ribs are placed such that P/e = 10 and e/H = 0.16. The Reynolds number varies from 10,000 to 45,000 in the first passage and 16,000 to 73,000 in the second passage. The rotational speed ranges from 0 to 400 rpm, which corresponds to maximum rotation numbers of 0.38 and 0.15 in the first and second passes, respectively. The blade-shaped feature affects the heat transfer and pressure loss in the cooling channels. In the second passage, the heat transfer on the outer wall and trailing surface is higher than the inner wall and leading surface due to flow impingement and the swirling motion induced by the blade-shaped tip turn. The rotational effect on the heat transfer and pressure loss is lower in the blade-shaped design than the planar design due to the feature of angled rotation. The tip wall heat transfer is significantly enhanced by rotation in this study. The overall heat transfer and pressure loss in this study is higher than the planar geometry due to the blade-shaped feature. The heat transfer and pressure loss characteristics from this study provide important information for the gas turbine blade internal cooling designs.

Build Direction Effects on Additively Manufactured Channels

2016 ◽  
Vol 138 (5) ◽  
Author(s):  
Jacob C. Snyder ◽  
Curtis K. Stimpson ◽  
Karen A. Thole ◽  
Dominic Mongillo
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Pressure Loss ◽  
Small Scale ◽  
Turbine Cooling ◽  
Gas Turbine Cooling ◽  
Gas Turbine Heat Transfer ◽  
Manufacturing Techniques ◽  
Traditional Manufacturing

With the advance of direct metal laser sintering (DMLS), also generically referred to as additive manufacturing (AM), novel geometric features of internal channels for gas turbine cooling can be achieved beyond those features using traditional manufacturing techniques. There are many variables, however, in the DMLS process that affect the final quality of the part. Of most interest to gas turbine heat transfer designers are the roughness levels and tolerance levels that can be held for the internal channels. This study investigates the effect of DMLS build direction and channel shape on the pressure loss and heat transfer measurements of small-scale channels. Results indicate that differences in pressure loss occur between the test cases with differing channel shapes and build directions, while little change is measured in heat transfer performance.

Sign in / Sign up

Export Citation Format

Share Document