Influence of Internal Flow on Film Cooling Effectiveness

1999 ◽  
Vol 122 (2) ◽  
pp. 327-333 ◽  
Author(s):  
Gu¨nter Wilfert ◽  
Stefan Wolff
Keyword(s):  
Film Cooling ◽  
Vortex Generator ◽  
Internal Flow ◽  
Thermochromic Liquid Crystal ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Hole ◽  
Cylindrical Holes ◽  
Flow Configurations ◽  
Inlet Conditions

Film cooling experiments were conducted to investigate the effects of internal flow conditions and plenum geometry on the film cooling effectiveness. The film cooling measurements show a strong influence of the coolant inlet conditions on film cooling performance. The present experiments were carried out on a flat plate with a row of cylindrical holes oriented at 30 deg with respect to a constant-velocity external flow, systematically varying the plenum geometry and blowing rates 0.5⩽M⩽1.25. Adiabatic film cooling measurements using the multiple narrow-banded thermochromic liquid crystal technique (TLC) were carried out, simulating a flow parallel to the mainstream flow with and without crossflow at the coolant hole entry compared with a standard plenum configuration. An impingement in front of the cooling hole entry with and without crossflow was also investigated. For all parallel flow configurations, ribs were installed at the top and bottom coolant channel wall. As the hole length-to-diameter ratio has an influence on the film cooling effectiveness, the wall thickness has also been varied. In order to optimize the benefit of the geometry effects with ribs, a vortex generator was designed and tested. Results from these experiments show in a region 5⩽X/D⩽80 downstream of the coolant injection location differences in adiabatic film cooling effectiveness between +5 percent and +65 percent compared with a standard plenum configuration. [S0889-504X(00)01102-8]

scholarly journals Influence of Internal Flow on Film Cooling Effectiveness

1999 ◽  
Author(s):  
Günter Wilfert ◽  
Stefan Wolff
Keyword(s):  
Film Cooling ◽  
Cross Flow ◽  
Vortex Generator ◽  
Internal Flow ◽  
Main Stream ◽  
Thermochromic Liquid Crystal ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Hole ◽  
Inlet Conditions

Film cooling experiments were conducted to investigate the effects of internal flow conditions and plenum geometry on the film cooling effectiveness. The film cooling measurements show a strong influence of the coolant inlet conditions on film cooling performance. The present experiments were carried out on a flat plate with a row of cylindrical holes oriented at 30 degrees with respect to a constant-velocity external flow, systematically varying the plenum geometry and blowing rates (0.5≤M≤1.25). Adiabatic film cooling measurements using the multiple narrow-banded Thermochromic Liquid Crystal-technique (TLC) were carried out simulating a flow parallel to the main stream flow with and without cross flow at the coolant hole entry compared with a standard plenum configuration. An impingement in front of the cooling hole entry with and without cross flow was also investigated. For all parallel flow configurations ribs were installed at the top and bottom coolant channel wall. As the hole length-to-diameter ratio has an influence on the film cooling effectiveness, the wall thickness has also been varied. In order to optimise the benefit of the geometry effects with ribs, a vortex generator was designed and tested. Results from these experiments show in a region 5≤X/D≤80 downstream of the coolant injection location differences in adiabatic film cooling effectiveness between +5% and +65% compared with a standard plenum configuration.

Injection Angle Influence of Secondary Holes on the Enhancement of Film Cooling Effectiveness With Horn-Shaped or Cylindrical Primary Holes

2017 ◽  
Author(s):  
Rui Zhu ◽  
Gongnan Xie ◽  
Terrence W. Simon
Keyword(s):  
Film Cooling ◽  
Numerical Study ◽  
Cylindrical Hole ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Injection Angle ◽  
Inclination Angles ◽  
Cooling Hole ◽  
Cylindrical Holes

Secondary holes to a main film cooling hole are used to improve film cooling performance by creating anti-kidney vortices. The effects of injection angle of the secondary holes on both film cooling effectiveness and surrounding thermal and flow fields are investigated in this numerical study. Two kinds of primary hole shapes are adopted. One is a cylindrical hole, the other is a horn-shaped hole which is designed from a cylindrical hole by expanding the hole in the transverse direction to double the hole size at the exit. Two smaller cylindrical holes, the secondary holes, are located symmetrically about the centerline and downstream of the primary hole. Three compound injection angles (α = 30°, 45° and 60°, β = 30°) of the secondary holes are analyzed while the injection angle of the primary hole is kept at 45°. Cases with various blowing ratios are computed. It is shown from the simulation that cooling effectiveness of secondary holes with a horn-shaped primary hole is better than that with a cylindrical primary hole, especially at high blowing ratios. With a cylindrical primary hole, increasing inclination angle of the secondary holes provides better cooling effectiveness because the anti-kidney vortices created by shallow secondary holes cannot counteract the kidney vortex pairs adequately, enhancing mixing of main flow and coolant. For secondary holes with a horn-shaped primary hole, large secondary hole inclination angles provide better cooling performance at low blowing ratios; but, at high blowing ratios, secondary holes with small inclination angles are more effective, as the film coverage becomes wider in the downstream area.

Turbine Blade Platform Film Cooling With Typical Stator-Rotor Purge Flow and Discrete-Hole Film Cooling

2009 ◽  
Vol 131 (4) ◽  
Author(s):  
Zhihong Gao ◽  
Diganta Narzary ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Pressure Loss ◽  
Total Pressure ◽  
Total Pressure Loss ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Hole ◽  
Purge Flow ◽  
Cylindrical Holes ◽  
Film Cooling Holes

This paper is focused on the effect of film-hole configurations on platform film cooling. The platform is cooled by purge flow from a simulated stator-rotor seal combined with discrete-hole film cooling within the blade passage. The cylindrical holes and laidback fan-shaped holes are assessed in terms of film-cooling effectiveness and total pressure loss. Lined up with the freestream streamwise direction, the film holes are arranged on the platform with two different layouts. In one layout, the film-cooling holes are divided into two rows and more concentrated on the pressure side of the passage. In the other layout, the film-cooling holes are divided into four rows and loosely distributed on the platform. Four film-cooling hole configurations are investigated totally. Testing was done in a five-blade cascade with medium high Mach number condition (0.27 and 0.44 at the inlet and the exit, respectively). The detailed film-cooling effectiveness distributions on the platform were obtained using pressure sensitive paint technique. Results show that the combined cooling scheme (slot purge flow cooling combined with discrete-hole film cooling) is able to provide full film coverage on the platform. The shaped holes present higher film-cooling effectiveness and wider film coverage than the cylindrical holes, particularly at higher blowing ratios. The hole layout affects the local film-cooling effectiveness. The shaped holes also show the advantage over the cylindrical holes with lower total pressure loss.

Turbine Blade Platform Film Cooling With Typical Stator-Rotor Purge Flow and Discrete-Hole Film Cooling

2008 ◽  
Author(s):  
Zhihong Gao ◽  
Diganta Narzary ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Pressure Loss ◽  
Total Pressure ◽  
Total Pressure Loss ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Hole ◽  
Purge Flow ◽  
Cylindrical Holes ◽  
Film Cooling Holes

This paper is focused on the effect of film hole configurations on platform film cooling. The platform is cooled by purge flow from a simulated stator-rotor seal combined with discrete-hole film cooling within the blade passage. The cylindrical holes and laidback fan-shaped holes are assessed in terms of film cooling effectiveness and total pressure loss. Lined up with the freestream streamwise direction, the film holes are arranged on the platform with two different layouts. In one layout, the film cooling holes are divided into two rows and more concentrated on the pressure side of the passage. In the other layout, the film cooling holes are divided into four rows and loosely distributed on the platform. Four film cooling hole configurations are investigated totally. Testing was done in a five-blade cascade with medium high Mach number condition (0.27 and 0.44 at the inlet and the exit, respectively). The detailed film cooling effectiveness distributions on the platform was obtained using pressure sensitive paint (PSP) technique. Results show that the combined cooling scheme (slot purge flow cooling combined with discrete hole film cooling) is able to provide full film coverage on the platform. The shaped holes present higher film cooling effectiveness and wider film coverage than the cylindrical holes, particularly at higher blowing ratios. The hole layout affects the local film cooling effectiveness. The shaped holes also show the advantage over the cylindrical holes with lower total pressure loss.

Implementation of Vortex Generator and Ramp to Improve Film Cooling Effectiveness on Blade Endwall

2021 ◽  
Author(s):  
Sadam Hussain ◽  
Xin Yan
Keyword(s):  
Numerical Methods ◽  
Film Cooling ◽  
Vortex Generator ◽  
Leading Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Baseline Case ◽  
Cooling Hole ◽  
Cooling Effects ◽  
Endwall Film Cooling

Abstract With the arrangements of vortex generators (VG) and ramp, film cooling effects on endwall near leading edge were numerically investigated at two blowing ratios (i.e. M = 0.5 and M = 1). To determine suitable numerical methods, mesh independency analysis and turbulence model selection were carried out based on the existing experimental data and LES results. With the numerical methods, flow fields near the leading edge were visualized to illustrate the influence of VG and ramp on coolant coverage on blade endwall. Film cooling effectiveness distributions on endwall and coolant trajectories near leading edge were compared among five different configurations with VG and ramp. The results show that the attachment of coolant on blade endwall is improved with the implement of VG between shaped-hole and leading edge. With the implementation of ramp on endwall between cooling hole and leading edge, the coolant spreads wider on endwall along pitchwise direction than the baseline case. With the implementation of VG and ramp, film cooling effect on endwall near leading edge is significantly improved as compared with the only ramp and only VG cases. Compared with the baseline case, pitchwise-averaged film cooling effectiveness on blade endwall near leading edge is increased by about 9%, and the film cooling effectiveness distributions on endwall along pitchwise direction become much uniform, for the case with both ramp and VG at M = 1.

Effects of Trenched Holes on Film Cooling of a Contoured Endwall Nozzle Vane

2011 ◽  
Vol 134 (4) ◽  
Author(s):  
Giovanna Barigozzi ◽  
Giuseppe Franchini ◽  
Antonio Perdichizzi ◽  
Silvia Ravelli
Keyword(s):  
Energy Loss ◽  
Film Cooling ◽  
Flow Rate Ratio ◽  
Pressure Probe ◽  
Intensity Level ◽  
Thermochromic Liquid Crystal ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Coolant Injection ◽  
Cylindrical Holes

The present paper investigates the effects of the application of trenched holes in the front part of a contoured film cooled endwall. Two trench configurations were tested, changing the trench depth. Tests have been carried out at low speed (M2is=0.2) and low inlet turbulence intensity level, with coolant mass flow rate ratio varied within the 0.5–2.5% range. Pressure probe traverses were performed downstream of the vane trailing edge to show the secondary flow field modifications and to evaluate trench additional losses. Endwall distributions of film cooling effectiveness have been obtained by the thermochromic liquid crystal (TLC) technique. For each injection condition, energy loss coefficient and film cooling effectiveness distributions were analyzed and compared with the ones obtained from rows of cylindrical holes. Laterally and area averaged effectiveness as well as pitch and mass averaged kinetic energy loss coefficients were computed to enlighten any change induced by the introduction of trenched holes. A uniform and high thermal coverage was obtained in the region just downstream of the trench, but it quickly decayed because of enforced mixing of coolant with main flow. Compared with the cylindrical hole configuration, trenches are able to provide a higher global cooling effectiveness, but a larger amount of coolant injection is required. The introduction of both trenches is responsible for a secondary thermodynamic loss increase of about 0.7% at low coolant injection rates. Increasing the blowing rates, the additional loss vanishes.

Experimental and Numerical Film Effectiveness Downstream a Row of Compound Angle Film Holes

2003 ◽  
Author(s):  
A. Khanicheh ◽  
M. E. Taslim
Keyword(s):  
High Temperature ◽  
Film Cooling ◽  
Computational Study ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Single Row ◽  
Cooling Hole ◽  
Cylindrical Holes ◽  
Film Cooling Holes ◽  
Compound Angle

High component lifetimes of modern gas turbines can be achieved by cooling the airfoils effectively. Film cooling is commonly employed on the airfoils and other engine hot section surfaces in order to protect them from the high thermal stress fields created by exposure to combustion gases. Complex geometries as well as optimized cooling considerations often dictate the use of compound-angled film cooling hole. In the present experimental and computational study, the effects that two different compound angle film cooling hole injection configurations have on film cooling effectiveness are investigated. Film cooling effectiveness measurements have been made downstream of a single row of compound angle cylindrical holes with a diameter of 7.5 mm, and a single row of compound angle, diffuser-shaped holes with an inlet diameter of 7.5 mm. The cylindrical holes were inclined (α=25°) with respect to the coverage surface and were oriented perpendicular to the high-temperature airflow direction. The diffuser-shaped holes had a compound angle of 45 degrees with respect to the high temperature air flow direction and, similar to the cylindrical film holes, a 25-deg angle with the coverage surface. Both geometries were tested over a blowing ratio range of 0.7 to 4.0. Surface temperatures were measured along four longitudinal rows of thermocouples covering the downstream area between two adjacent holes. The results showed that the best overall protection over the widest range of blowing ratios was provided by the diffuser-shaped film cooling holes. Compared with the cylindrical hole results, the diffuser-shaped expansion holes produced higher film cooling effectiveness downstream of the film cooling holes, particularly at high blowing ratios. The increased cross sectional area at the shaped hole exit compared to that of the cylindrical hole lead to a reduction of the mean velocity, thus the reduction of the momentum flux of the jet exiting the hole. Therefore, the penetration of the jet into the main flow was reduced, resulting in an increased cooling effectiveness. A commercially available CFD software package was used to study film cooling effectiveness downstream of the row of holes. Comparisons between the experimentally measured and numerically calculated film effectiveness distributions showed that the computed results are in reasonable agreement with the measured results. Therefore, CFD can be considered as a viable tool to predict the cooling performance of different film cooling configurations in a parametric study. A more realistic turbulence model, possibly adopting a two-layer model that incorporates boundary layer anisotropy, in the computational study may improve the predicted results.

Effect of Upstream Step on Flat Plate Film-Cooling Effectiveness Using PSP

2011 ◽  
Vol 133 (4) ◽  
Author(s):  
Akhilesh P. Rallabandi ◽  
Joshua Grizzle ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Axial Angle ◽  
Step Effect ◽  
Cooling Hole ◽  
Cylindrical Holes ◽  
Film Cooling Holes ◽  
Compound Angle ◽  
State Pressure

The effect of a step positioned upstream of a row of film-cooling holes on the film-cooling effectiveness is studied systematically using the steady state pressure sensitive paint technique. The upstream step effect is studied on four separate hole geometries: simple angled (axial angle of 30 deg) and compound angled (axial angle of 30 deg and compound angle of 45 deg) and cylindrical and fan-shaped film-cooling holes. Each plate considered has seven holes, each hole 4 mm in diameter. The plates with cylindrical holes have a spacing of 3 diameters (12 mm) between the centers of two consecutive holes while the fan-shaped holes have a spacing of 3.75 diameters (15 mm). Three different step heights (12.5%d, 25%d, and 37.5%d) are studied. The effect of the width of the step is also studied; the distance of the step upstream of the hole and the positioning of the step downstream of the film-cooling hole. Four separate blowing ratios are reported for all tests: M=0.3, M=0.6, M=1.0, and M=1.5. All studies have been conducted with a mainstream of 25 m/s velocity at an ambient temperature of 22°C. Results indicate an increase in film-cooling effectiveness in the region near the hole due to the upstream step for all the plates considered. This increase due to the step is found to be most significant in the case of compound angled cylindrical holes and least significant in the case of simple angled fan-shaped holes.

Film Cooling Effectiveness From Two-Row of Compound Angled Cylindrical Holes Using PSP Technique

2018 ◽  
Author(s):  
Nian Wang ◽  
Mingjie Zhang ◽  
Chao-Cheng Shiau ◽  
Je-Chin Han
Keyword(s):  
Flat Plate ◽  
Film Cooling ◽  
Density Ratio ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Free Stream Turbulence ◽  
Cooling Hole ◽  
Cylindrical Holes ◽  
Inclined Angle ◽  
Density Ratios

This study investigates the combined effects of blowing ratio and density ratio on flat plate film cooling effectiveness from two-row of compound angled cylindrical holes. Two arrangements of two-row compound angled cylindrical holes are tested: the first row and second row are oriented in staggered but same compound angled direction (β = +45° for the first row, +45° for the second row); the first row and second row are oriented in inline but opposite direction (β = +45° for the first row, −45° for the second row). Each cooling hole is 4 mm in diameter with an inclined angle 30°. The streamwise distance between the two rows is fixed at 4d and the spanwise pitch between the two holes (p) is 4d, 6d, and 8d, respectively. The experiments are performed at four blowing ratios (M = 0.5, 1.0, 1.5, 2.0) and three density ratios (DR = 1.0, 1.5, 2.0). The free stream turbulence intensity is kept at 6%. Detailed film cooling effectiveness distributions are obtained using the steady state pressure-sensitive paint (PSP) technique. The detailed film cooling effectiveness contours are presented and the spanwise averaged film effectiveness results are compared over the range of flow parameters. Film cooling effectiveness correlations are developed for both inline and staggered compound angled cylindrical holes. The results provide baseline information for the flat plate film cooling analysis with two-row of compound angled cylindrical holes.

Experimental Investigation of Louver Cooling Scheme on Gas Turbine Vane Suction Side

2011 ◽  
Author(s):  
T. Elnady ◽  
O. Hassan ◽  
I. Hassan ◽  
L. Kadem ◽  
T. Lucas
Keyword(s):  
Experimental Investigation ◽  
Gas Turbine ◽  
Film Cooling ◽  
Density Ratio ◽  
Suction Side ◽  
Thermochromic Liquid Crystal ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Cylindrical Holes

An experimental investigation has been performed to measure the film cooling performance of louver scheme over a scaled vane of high-pressure gas turbine using a two-dimensional cascade. Two rows of axially oriented louver scheme are used to cool the suction side and their performance is compared with two similar rows of standard cylindrical holes. The effect of hole location on the cooling performance is investigated for each row individually, then the row interaction is investigated for both rows at four different blowing ratios ranging from 1 to 2 with a 0.9 density ratio. The exit Reynolds number based on the true chord is 1.5E5 and exit Mach number is 0.23. The temperature distribution on the vane is mapped using a transient Thermochromic Liquid Crystal (TLC) technique to obtain the local distributions of the heat transfer coefficient and film cooling effectiveness. The louver scheme shows a superior cooling effectiveness than that of the cylindrical holes at all blowing ratios in terms of protection and lateral coverage. The row location highly affects the cooling performance for both the louver and cylindrical scheme.

Sign in / Sign up

Export Citation Format

Share Document