Evaporation Heat Transfer and Pressure Drop in Horizontal Tubes With Strip-Type Inserts Using Refrigerant 600a

1999 ◽  
Vol 122 (2) ◽  
pp. 387-391 ◽  
Author(s):  
S.-S. Hsieh ◽  
K.-J. Jang ◽  
Y.-C. Tsai
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pressure Drop ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Pressure Drops ◽  
Horizontal Tubes ◽  
Evaporation Heat

Results of a study on saturated boiling heat transfer of refrigerant R-600a in horizontal tubes (ID=10.6 mm) with strip-type inserts (longitudinal strip LS with/without perforated holes and cross-strip CS inserts) are reported. Local heat transfer coefficients are measured for a range of heat flux (9.1∼31.2 kW/m2), mass velocity (8.23∼603.3 kg/m2s), and equilibrium mass quality (⩽0.8) and the influences were studied. The data were compared with the performance of the corresponding smooth tubes. Enhancement factors are presented and discussed. Pressure drop measurement was also conducted and it is found that both single-phase and two-phase pressure drops increase with increasing heat flux levels and mass velocities. [S0022-1481(00)00302-9]

Local Heat Transfer Coefficients and Pressure Drop During Evaporation in a Smooth Horizontal Tube

2002 ◽  
Author(s):  
C. Aprea ◽  
A. Greco ◽  
G. P. Vanoli
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pressure Drop ◽  
Mass Flux ◽  
Local Heat Transfer ◽  
Horizontal Tube ◽  
Local Heat ◽  
Working Fluid ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients

R22 is the most widely employed HCFC working fluid in vapour compression plant. HCFCs must be replaced within 2020. Major problems arise with the substitution of the working fluids, related to the decrease in performance of the plant. Therefore, extremely accurate design procedures are needed. The relative sizing of each of the components of the plant is crucial for cycle performance. For this reason, the knowledge of the new fluids heat transfer characteristics in condensers and evaporators is required. The local heat transfer coefficients and pressure drop of pure R22 and of the azeotropic mixture R507 (R125-R143a 50%/50% in weight) have been measured during convective boiling. The test section is a smooth horizontal tube made of a with a 6 mm I.D. stainless steel tube, 6 m length, uniformly heated by Joule effect. The effects of heat flux, mass flux and evaporation pressure on the heat transfer coefficients are investigated. The evaporating pressure varies within the range 3 ÷10 bar, the refrigerant mass flux within the range 200 ÷ 1000 kg/m2s, the heat flux within 0 ÷ 44 kW/m2. A comparison have been carried out between the experimental data and those predicted by means of the most credited literature relationships.

Local and Average Heat Transfer and Pressure Drop for Refrigerants Evaporating in Horizontal Tubes

1960 ◽  
Vol 82 (3) ◽  
pp. 189-196 ◽  
Author(s):  
M. Altman ◽  
R. H. Norris ◽  
F. W. Staub
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Test Facility ◽  
Transfer Coefficients ◽  
Local Pressure ◽  
Average Heat ◽  
Heat Transfer Coefficients ◽  
Horizontal Tubes

A test facility is described that has been constructed to investigate local heat transfer and pressure drop for evaporating or condensing refrigerants. The empirical method of B. Pierre [1] for correlating the average heat-transfer coefficients of refrigerants evaporating in horizontal tubes is presented in conjunction with the data of several authors [3–6]. Data on local heat-transfer coefficients and pressure drop are presented for Refrigerant-22 evaporating in two 4-ft-long, 0.343-in-ID straight horizontal tubes, and are correlated by a refinement of the curve proposed in [1]. The procedure of Martinelli-Nelson [9] correlated the data for local pressure drop within 15 per cent.

scholarly journals Experimental investigation of the two-phase local heat transfer coefficients for condensation of R134a in a micro-structured plate heat exchanger

2021 ◽  
Author(s):  
Ru Wang ◽  
Tingyan Sun ◽  
Anja-Elsa Polzin ◽  
Stephan Kabelac
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Exchanger ◽  
Saturation Pressure ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Plate Heat Exchanger ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Plate Heat

AbstractPlate heat exchangers are widely used for two-phase heat transfer in the industrial applications, and recently more attention has been paid to the plate heat exchangers with enhanced surface due to their better heat transfer performance. In this paper, the local condensation heat transfer coefficients are studied using R134a in a micro-structured plate heat exchanger. In order to obtain a more accurate prediction model, a series of measurements are conducted under various operating conditions. The mass flux of R134a varied from 47 kg/m2s to 77 kg/m2s, the saturation pressure in the condenser ranged from 6.32 bar to 8.95 bar, and the value of the heat flux was between 13 kW/m2 and 22 kW/m2. The local two-phase Nusselt number increases with the increase of the mass flux. As the saturation pressure increases, the local two-phase Nusselt number increase at the beginning of the condensation and decrease at the end of the condensation. However, the effect of heat flux on local heat transfer is irregular, due to the interaction of these parameters in the experiment. Comparing with the unstructured plate heat exchanger, R134a condenses faster at the beginning of the process in the micro-sturctured plate heat exchanger, and the local heat transfer performs better when the vapor quality is lower. Combing with the phenomenon that the overall heat flux in micro-structured plate is larger under the same working conditions, it shows that the overall heat transfer of the micro-structured plate is improved, but the local heat transfer uprades only at lower vapor qualities. A new correlation is developed, it predicts all the experimental data within the root mean square error 10%, and a new correlation for the waterside is suggested as well.

scholarly journals Condensation inside smooth horizontal tubes: Part 1. Survey of the methods of heat-exchange prediction

2015 ◽  
Vol 19 (5) ◽  
pp. 1769-1789 ◽  
Author(s):  
Volodymyr Rifert ◽  
Volodymyr Sereda
Keyword(s):  
Heat Transfer ◽  
Heat Exchange ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Film Condensation ◽  
Experimental Investigations ◽  
Phase Flow ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Horizontal Tubes

Survey of the works on condensation inside smooth horizontal tubes published from 1955 to 2013 has been performed. Theoretical and experimental investigations, as well as more than 25 methods and correlations for heat transfer prediction are considered. It is shown that accuracy of this prediction depends on the accuracy of volumetric vapor content and pressure drop at the interphase. The necessity of new studies concerning both local heat transfer coefficients and film condensation along tube perimeter and length under annular, stratified and intermediate regimes of phase flow was substantiated. These characteristics being defined will allow determining more precisely the boundaries of the flow regimes and the methods of heat transfer prediction.

Heat Transfer Enhancement in Triangular Ducts With an Array of Side-Entry Wall/Impinged Jets

1999 ◽  
Author(s):  
J.-J. Hwang ◽  
C.-S. Cheng ◽  
Y.-P. Tsia
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Leading Edge ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Enhancement ◽  
Transfer Coefficients ◽  
Pressure Drops ◽  
Heat Transfer Coefficients ◽  
Inclined Angle

An experimental study has been performed to measure local heat transfer coefficients and static well pressure drops in leading-edge triangular ducts cooled by wall/impinged jets. Coolant provided by an array of equally spaced wall jets is aimed at the leading-edge apex and exits from the radial outlet. Detailed heat transfer coefficients are measured for the two walls forming the apex using transient liquid crystal technique. Secondary-flow structures are visualized to realize the mechanism of heat transfer enhancement by wall/impinged jets. Three right-triangular ducts of the same altitude and different apex angles of β = 30 deg (Duct A), 45 deg (Duct B) and 60 deg (Duct C) are tested for various jet Reynolds numbers (3000≦Rej≦12600) and jet spacings (s/d = 3.0 and 6.0). Results show that an increase in Rej increases the heat transfer on both walls. Local heat transfer on both walls gradually decreases downstream due to the crossflow effect. At the same Rej, the Duct C has the highest wall-averaged heat transfer because of the highest jet center velocity as well as the smallest jet inclined angle. Moreover, the distribution of static pressure drop based on the local through flow rate in the present triangular duct is similar to that that of developing straight pipe flows. Average jet Nusselt numbers on the both walls have been correlated with jet Reynolds number for three different duct shapes.

Experimental Study of Evaporation Heat Transfer Characteristics and Pressure Drops of R410A and R134a in a Multiport Mini-Channel

2009 ◽  
Author(s):  
Jatuporn Kaew-On ◽  
Somchai Wongwises
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Transfer Coefficients ◽  
Pressure Drops ◽  
Heat Transfer Coefficients ◽  
Evaporation Heat ◽  
Evaporation Heat Transfer ◽  
R 134A

The evaporation heat transfer coefficients and pressure drops of R-410A and R-134a flowing through a horizontal-aluminium rectangular multiport mini-channel having a hydraulic diameter of 3.48 mm are experimentally investigated. The test runs are done at refrigerant mass fluxes ranging between 200 and 400 kg/m2s. The heat fluxes are between 5 and 14.25 kW/m2, and refrigerant saturation temperatures are between 10 and 30 °C. The effects of the refrigerant vapour quality, mass flux, saturation temperature and imposed heat flux on the measured heat transfer coefficient and pressure drop are investigated. The experimental data show that in the same conditions, the heat transfer coefficients of R-410A are about 20–50% higher than those of R-134a, whereas the pressure drops of R-410A are around 50–100% lower than those of R-134a. The new correlations for the evaporation heat transfer coefficient and pressure drop of R-410A and R-134a in a multiport mini-channel are proposed for practical applications.

Comparison of Pressure Drop and Endwall Heat Transfer Measurements to Flow Visualization Testing of Solid and Porous Pin Fin Arrays

2009 ◽  
Author(s):  
Jared M. Pent ◽  
Jay S. Kapat ◽  
Mark Ricklick
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Visualization ◽  
Local Heat Transfer ◽  
Ccd Camera ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Porous Aluminum ◽  
Pin Fins ◽  
A Charge

This paper examines the local and averaged endwall heat transfer effects of a staggered array of porous aluminum pin fins with a channel blockage ratio (blocked channel area divided by open channel area) of 50%. Two sets of pins were used with pore densities of 0 (solid) and 10 pores per inch (PPI). The pressure drop through the channel was also determined for several flow rates using each set of pins. Local heat transfer coefficients on the endwall were measured using Thermochromatic Liquid Crystal (TLC) sheets recorded with a charge-coupled device (CCD) camera. Static and total pressure measurements were taken at the entrance and exit of the test section to determine the overall pressure drop through the channel and explain the heat transfer trends through the channel. The heat transfer and pressure data was then compared to flow visualization tests that were run using a fog generator. Results are presented for the two sets of pins with Reynolds numbers between 25000 and 130000. Local HTC (heat transfer coefficient) profiles as well as spanwise and streamwise averaged HTC plots are displayed for both pin arrays. The thermal performance was calculated for each pin set and Reynolds number. All experiments were carried out in a channel with an X/D of 1.72, a Y/D of 2.0, and a Z/D of 1.72.

Investigation of Buoyancy Effects in Asymmetrically Heated Near-Critical Flows of Carbon Dioxide in Horizontal Microchannels Using Infrared Thermography

2021 ◽  
Author(s):  
Lindsey V. Randle ◽  
Brian M. Fronk
Keyword(s):  
Heat Transfer ◽  
Carbon Dioxide ◽  
Heat Flux ◽  
Infrared Thermography ◽  
Test Section ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Parallel Microchannels

Abstract In this study, we use infrared thermography to calculate local heat transfer coefficients of top and bottom heated flows of near-critical carbon dioxide in an array of parallel microchannels. These data are used to evaluate the relative importance of buoyancy for different flow arrangements. A Joule heated thin wall made of Inconel 718 applies a uniform heat flux either above or below the horizontal flow. A Torlon PAI test section consists of three parallel microchannels with a hydraulic diameter of 923 μm. The reduced inlet temperature (TR = 1.006) and reduced pressure (PR = 1.03) are held constant. For each heater orientation, the mass flux (520 kgm−2s−2 ≤ G ≤ 800 kgm−2s−2) and heat flux (4.7 Wcm−2 ≤ q″ ≤ 11.1 Wcm−2) are varied. A 2D resistance network analysis method calculates the bulk temperatures and heat transfer coefficients. In this analysis, we divide the test section into approximately 250 segments along the stream-wise direction. We then calculate the bulk temperatures using the enthalpy from the upstream segment, the heat flux in a segment, and the pressure. To isolate the effect of buoyancy, we screen the data to omit conditions where flow acceleration may be important or where relaminarization may occur. In the developed region of the channel, there was a 10 to 15 percent reduction of the local heat transfer coefficients for the upward heating mode compared to downward heating with the same mass and heat fluxes. Thus buoyancy effects should be considered when developing correlations for these types of flow.

Prediction of Horizontal Tubeside Condensation of Pure Components Using Flow Regime Criteria

1980 ◽  
Vol 102 (3) ◽  
pp. 471-476 ◽  
Author(s):  
G. Breber ◽  
J. W. Palen ◽  
J. Taborek
Keyword(s):  
Heat Transfer ◽  
Prediction Method ◽  
Local Heat Transfer ◽  
Flow Regimes ◽  
Local Heat ◽  
Pure Component ◽  
Liquid Volume ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Horizontal Tubes

In order to select the appropriate correlations for prediction of horizontal tubeside condensation heat transfer coefficients, it is necessary to estimate what types of flow patterns exist at various points along the tube. The main criteria required are shown to be the ratio of shear to gravity forces on the condensate film and the ratio of vapor volume to liquid volume. A recently proposed prediction method by Taitel and Dukler is compared with observed flow regimes for condensation in horizontal tubes. The theoretically obtained parameters are shown to characterize the flow regimes well. Based on these parameters, a simplified procedure for prediction of local heat transfer coefficients for pure component condensation in horizontal tubes is proposed.

Sign in / Sign up

Export Citation Format

Share Document