Local and Average Heat Transfer and Pressure Drop for Refrigerants Evaporating in Horizontal Tubes

1960 ◽  
Vol 82 (3) ◽  
pp. 189-196 ◽  
Author(s):  
M. Altman ◽  
R. H. Norris ◽  
F. W. Staub
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Test Facility ◽  
Transfer Coefficients ◽  
Local Pressure ◽  
Average Heat ◽  
Heat Transfer Coefficients ◽  
Horizontal Tubes

A test facility is described that has been constructed to investigate local heat transfer and pressure drop for evaporating or condensing refrigerants. The empirical method of B. Pierre [1] for correlating the average heat-transfer coefficients of refrigerants evaporating in horizontal tubes is presented in conjunction with the data of several authors [3–6]. Data on local heat-transfer coefficients and pressure drop are presented for Refrigerant-22 evaporating in two 4-ft-long, 0.343-in-ID straight horizontal tubes, and are correlated by a refinement of the curve proposed in [1]. The procedure of Martinelli-Nelson [9] correlated the data for local pressure drop within 15 per cent.

scholarly journals Condensation inside smooth horizontal tubes: Part 1. Survey of the methods of heat-exchange prediction

2015 ◽  
Vol 19 (5) ◽  
pp. 1769-1789 ◽  
Author(s):  
Volodymyr Rifert ◽  
Volodymyr Sereda
Keyword(s):  
Heat Transfer ◽  
Heat Exchange ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Film Condensation ◽  
Experimental Investigations ◽  
Phase Flow ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Horizontal Tubes

Survey of the works on condensation inside smooth horizontal tubes published from 1955 to 2013 has been performed. Theoretical and experimental investigations, as well as more than 25 methods and correlations for heat transfer prediction are considered. It is shown that accuracy of this prediction depends on the accuracy of volumetric vapor content and pressure drop at the interphase. The necessity of new studies concerning both local heat transfer coefficients and film condensation along tube perimeter and length under annular, stratified and intermediate regimes of phase flow was substantiated. These characteristics being defined will allow determining more precisely the boundaries of the flow regimes and the methods of heat transfer prediction.

Prediction of Horizontal Tubeside Condensation of Pure Components Using Flow Regime Criteria

1980 ◽  
Vol 102 (3) ◽  
pp. 471-476 ◽  
Author(s):  
G. Breber ◽  
J. W. Palen ◽  
J. Taborek
Keyword(s):  
Heat Transfer ◽  
Prediction Method ◽  
Local Heat Transfer ◽  
Flow Regimes ◽  
Local Heat ◽  
Pure Component ◽  
Liquid Volume ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Horizontal Tubes

In order to select the appropriate correlations for prediction of horizontal tubeside condensation heat transfer coefficients, it is necessary to estimate what types of flow patterns exist at various points along the tube. The main criteria required are shown to be the ratio of shear to gravity forces on the condensate film and the ratio of vapor volume to liquid volume. A recently proposed prediction method by Taitel and Dukler is compared with observed flow regimes for condensation in horizontal tubes. The theoretically obtained parameters are shown to characterize the flow regimes well. Based on these parameters, a simplified procedure for prediction of local heat transfer coefficients for pure component condensation in horizontal tubes is proposed.

Local Heat Transfer Coefficients and Pressure Drop During Evaporation in a Smooth Horizontal Tube

2002 ◽  
Author(s):  
C. Aprea ◽  
A. Greco ◽  
G. P. Vanoli
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pressure Drop ◽  
Mass Flux ◽  
Local Heat Transfer ◽  
Horizontal Tube ◽  
Local Heat ◽  
Working Fluid ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients

R22 is the most widely employed HCFC working fluid in vapour compression plant. HCFCs must be replaced within 2020. Major problems arise with the substitution of the working fluids, related to the decrease in performance of the plant. Therefore, extremely accurate design procedures are needed. The relative sizing of each of the components of the plant is crucial for cycle performance. For this reason, the knowledge of the new fluids heat transfer characteristics in condensers and evaporators is required. The local heat transfer coefficients and pressure drop of pure R22 and of the azeotropic mixture R507 (R125-R143a 50%/50% in weight) have been measured during convective boiling. The test section is a smooth horizontal tube made of a with a 6 mm I.D. stainless steel tube, 6 m length, uniformly heated by Joule effect. The effects of heat flux, mass flux and evaporation pressure on the heat transfer coefficients are investigated. The evaporating pressure varies within the range 3 ÷10 bar, the refrigerant mass flux within the range 200 ÷ 1000 kg/m2s, the heat flux within 0 ÷ 44 kW/m2. A comparison have been carried out between the experimental data and those predicted by means of the most credited literature relationships.

Local Heat Transfer Coefficients around Horizontal Tubes in Fluidized Beds

1980 ◽  
Vol 102 (1) ◽  
pp. 152-157 ◽  
Author(s):  
R. Chandran ◽  
J. C. Chen ◽  
F. W. Staub
Keyword(s):  
Heat Transfer ◽  
Particle Size ◽  
Fluidized Beds ◽  
Local Heat Transfer ◽  
Local Heat ◽  
General Tendency ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Horizontal Tubes ◽  
System Pressure

The local characteristics of heat transfer from horizontal tubes immersed in fluidized beds were investigated experimentally. Steady-state heat transfer measurements were obtained in air-fluidized beds of glass beads, both for a single tube and a ten-row bare tube bundle. The test results indicated that local heat transfer coefficients are strongly influenced by angular position and gas flow rate, as well as by particle size and system pressure. The heat transfer coefficients, averaged around the circumference of the tube, exhibited a general tendency to increase with decreasing particle size and increasing system pressure. The heat transfer coefficients for a tube in an inner-row position within the bundle were found to be slightly higher than those for a tube in the bottom-row. Comparison of the average heat transfer coefficient data obtained in this study with some of the existing correlations for heat transfer from horizontal tubes showed that the correlations are unsatisfactory.

Evaporation Heat Transfer and Pressure Drop in Horizontal Tubes With Strip-Type Inserts Using Refrigerant 600a

1999 ◽  
Vol 122 (2) ◽  
pp. 387-391 ◽  
Author(s):  
S.-S. Hsieh ◽  
K.-J. Jang ◽  
Y.-C. Tsai
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pressure Drop ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Pressure Drops ◽  
Horizontal Tubes ◽  
Evaporation Heat

Results of a study on saturated boiling heat transfer of refrigerant R-600a in horizontal tubes (ID=10.6 mm) with strip-type inserts (longitudinal strip LS with/without perforated holes and cross-strip CS inserts) are reported. Local heat transfer coefficients are measured for a range of heat flux (9.1∼31.2 kW/m2), mass velocity (8.23∼603.3 kg/m2s), and equilibrium mass quality (⩽0.8) and the influences were studied. The data were compared with the performance of the corresponding smooth tubes. Enhancement factors are presented and discussed. Pressure drop measurement was also conducted and it is found that both single-phase and two-phase pressure drops increase with increasing heat flux levels and mass velocities. [S0022-1481(00)00302-9]

Measurement of Condensation Heat Transfer Coefficients at Near-Critical Pressures in Refrigerant Blends

2006 ◽  
Vol 129 (8) ◽  
pp. 958-965 ◽  
Author(s):  
Yirong Jiang ◽  
Biswajit Mitra ◽  
Srinivas Garimella ◽  
Ulf C. Andresen
Keyword(s):  
Heat Transfer ◽  
Mass Flux ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Condensation Heat Transfer ◽  
Liquid Region ◽  
Transfer Coefficients ◽  
Reduced Pressure ◽  
Heat Transfer Coefficients ◽  
Horizontal Tubes

This paper presents the results of an experimental study on condensation heat transfer of refrigerant blends R404A and R410A flowing through horizontal tubes of 9.4 and 6.2mm inner diameter at nominal pressures of 80% and 90% of the critical pressure. Local heat transfer coefficients were measured for the mass flux range 200<G<800kg∕m2‐s in small quality increments over the entire vapor-liquid region. Heat transfer coefficients increased with quality and mass flux, while the effect of reduced pressure was not very significant within this range of pressures. The heat transfer coefficients increased with a decrease in diameter.

Pressure Based Prediction of Spray Cooling Heat Transfer Coefficients

2007 ◽  
Author(s):  
Thierry Some ◽  
Eckhard Lehmann ◽  
Hitoshi Sakamoto ◽  
Jungho Kim ◽  
Jin Taek Chung ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Spray Cooling ◽  
Local Heat Transfer Coefficient ◽  
Transfer Coefficients ◽  
Local Pressure ◽  
Heat Transfer Coefficients

An important goal of spray cooling research is the ability to predict local heat transfer coefficient from the spray hydrodynamics. It is postulated in this work that the local pressure is the controlling parameter for local heat transfer coefficient. To test this hypothesis, local pressure and heat transfer data were obtained for a 1×1, 1×2, and 2×2 arrays of hollow cone sprays at two pressures and three standoff distances. A correlation between the pressure and heat transfer coefficient was determined, then used to “predict” the heat transfer coefficient from the pressure data. The local variations in heat transfer coefficient were captured well using this technique, and the area-averaged heat transfer coefficient could be predicted within 12.6%. The technique needs to be verified with different nozzles and fluids over a wider range of conditions.

Heat Transfer From Arrays of Impinging Jets with Large Jet-to-Jet Spacing

1978 ◽  
Vol 100 (2) ◽  
pp. 352-357 ◽  
Author(s):  
B. R. Hollworth ◽  
R. D. Berry
Keyword(s):  
Heat Transfer ◽  
Local Heat Transfer ◽  
Target Surface ◽  
Turbulent Jets ◽  
Local Heat ◽  
Impinging Jets ◽  
Transfer Coefficients ◽  
Average Heat ◽  
Turbine Cooling ◽  
Heat Transfer Coefficients

Local and average convective heat transfer coefficients were measured for arrays of widely spaced impinging air jets and correlated in terms of system geometry, air flow, and fluid properties. The configurations were square arrays of circular turbulent jets (spaced from 10–25 diameters apart) incident upon a flat isothermal target surface. Independent parameters were varied over ranges generally corresponding to gas turbine cooling applications. Local heat transfer coefficients were influenced by interference from neighboring jets only when the target plate and the jet orifice plate were less than five jet diameters apart. Average heat transfer coefficients were nearly equal for all the arrays tested as long as the coolant flow per unit area of target surface was held constant. In fact, there was a tendency for the more widely spaced configurations to produce slightly higher average heat transfer under such conditions.

Sign in / Sign up

Export Citation Format

Share Document