Impinging Jet Boiling of a Fluorinert Liquid on a Foil Heater Array

2000 ◽  
Vol 122 (2) ◽  
pp. 132-137 ◽  
Author(s):  
Wataru Nakayama ◽  
Masud Behnia ◽  
Hiroaki Mishima
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Heat Flux ◽  
Thick Plate ◽  
Jet Impingement ◽  
Thermal Mass ◽  
Rapid Rise ◽  
Slot Nozzle ◽  
Transfer Behavior ◽  
Impinging Flow

An experimental study of forced convection in impinging flow, using fluorocarbon FX3250 and a simulated electronic chip, was performed. A test section consisting of a 35 mm long, 1 mm wide slot nozzle in a 2 mm thick plate offset 2 mm from the heat source was used. The simulated chip array consisted of five foil strip (4 mm wide) heaters, positioned with the center strip directly beneath the slot nozzle. The velocity of the coolant was varied from 0.53 to 5 m/s, and the subcooling in the range from 2 to 21 K. The experiments were conducted focusing on two cases. First, only the center strip was heated. Second, all the heaters were energized, and the strip-by-strip variations of heat transfer were measured. The critical heat flux (CHF) on the center strip, determined by sensing the onset of oscillations and subsequent rapid rise of foil temperatures, was found considerably lower than those predicted by the existing correlations. It is pointed out that the thermal mass of the test heater could be an important factor for the CHF. The heat transfer behavior of other strips showed channel-flow or jet-impingement mode depending on the strip location and the coolant flow rate. [S1043-7398(00)00202-4]

Heat Transfer Characteristics of Downward Facing Hot Horizontal Surfaces Using Mist Jet Impingement

2017 ◽  
Author(s):  
Ashutosh Kumar Yadav ◽  
Parantak Sharma ◽  
Avadhesh Kumar Sharma ◽  
Mayank Modak ◽  
Vishal Nirgude ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Surface Heat Flux ◽  
Cooling System ◽  
Water Pressure ◽  
Jet Impingement ◽  
Surface Heat ◽  
Heat Transfer Characteristics ◽  
Impingement Cooling ◽  
Transfer Characteristics

Impinging jet cooling technique has been widely used extensively in various industrial processes, namely, cooling and drying of films and papers, processing of metals and glasses, cooling of gas turbine blades and most recently cooling of various components of electronic devices. Due to high heat removal rate the jet impingement cooling of the hot surfaces is being used in nuclear industries. During the loss of coolant accidents (LOCA) in nuclear power plant, an emergency core cooling system (ECCS) cool the cluster of clad tubes using consisting of fuel rods. Controlled cooling, as an important procedure of thermal-mechanical control processing technology, is helpful to improve the microstructure and mechanical properties of steel. In industries for heat transfer efficiency and homogeneous cooling performance which usually requires a jet impingement with improved heat transfer capacity and controllability. It provides better cooling in comparison to air. Rapid quenching by water jet, sometimes, may lead to formation of cracks and poor ductility to the quenched surface. Spray and mist jet impingement offers an alternative method to uncontrolled rapid cooling, particularly in steel and electronics industries. Mist jet impingement cooling of downward facing hot surface has not been extensively studied in the literature. The present experimental study analyzes the heat transfer characteristics a 0.15mm thick hot horizontal stainless steel (SS-304) foil using Internal mixing full cone (spray angle 20 deg) mist nozzle from the bottom side. Experiments have been performed for the varied range of water pressure (0.7–4.0 bar) and air pressure (0.4–5.8 bar). The effect of water and air inlet pressures, on the surface heat flux has been examined in this study. The maximum surface heat flux is achieved at stagnation point and is not affected by the change in nozzle to plate distance, Air and Water flow rates.

Heat transfer of multi-slot nozzle air jet impingement with different Reynolds number

2020 ◽  
pp. 116470
Author(s):  
Jinqi Zhu ◽  
Ruifeng Dou ◽  
Ye Hu ◽  
Shixing Zhang ◽  
Xuyun Wang
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Jet Impingement ◽  
Slot Nozzle ◽  
Air Jet

Experimental Study on Heat Transfer Augmentation for High Heat Flux Removal in Rib-Roughened Narrow Channels

1998 ◽  
Vol 35 (9) ◽  
pp. 671-678 ◽  
Author(s):  
Md. Shafiqul ISLAM ◽  
Ryutaro HINO ◽  
Katsuhiro HAGA ◽  
Masanori MONDE ◽  
Yukio SUDO
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Heat Flux ◽  
High Heat ◽  
High Heat Flux ◽  
Narrow Channels ◽  
Heat Transfer Augmentation ◽  
Rib Roughened

Submerged Jet Impingement Cooling of a Nanostructured Plate

2010 ◽  
Author(s):  
Muhsincan Sesen ◽  
Ali Kosar ◽  
Ebru Demir ◽  
Evrim Kurtoglu ◽  
Nazli Kaplan ◽  
...  
Keyword(s):  
Thin Film ◽  
Heat Transfer ◽  
Heat Flux ◽  
Silicon Wafer ◽  
Heat Removal ◽  
Jet Impingement ◽  
Wafer Surface ◽  
Small Scale ◽  
Copper Thin Film ◽  
Thin Film Layer

In this paper, the results of a series of heat transfer experiments conducted on a compact electronics cooling device based on single phase jet impingement techniques are reported. Deionized-water is propelled into four microchannels of inner diameter 685 μm which are used as nozzles and located at a nozzle to surface distance of 2.5mm. The generated jet impingement is targeted through these channels towards the surface of a nanostructured plate. This plate of size 20mmx20mm consisted of ∼600 nm long copper nanorod arrays with an average nanorod diameter of ∼150 nm, which were integrated on top of a silicon wafer substrate coated with a copper thin film layer (i.e. Cu-nanorod/Cu-film/Silicon-wafer). Heat removal characteristics induced through jet impingement are investigated using the nanostructured plate and compared to results obtained from a flat plate of copper thin film coated on silicon wafer surface. Enhancement in heat transfer up to 15% using the nanostructured plate has been reported in this paper. Heat generated by small scale electronic devices is simulated using a thin film heater placed on an aluminum base. Surface temperatures are recorded by a data acquisition system with the thermocouples integrated on the surface at various locations. Constant heat flux provided by the film heater is delivered to the nanostructured plate placed on top of the base. Volumetric flow rate and heat flux values were varied in order to better characterize the potential enhancement in heat transfer by nanostructured surfaces.

scholarly journals Experimental study of curvature effects on jet impingement heat transfer on concave surfaces

2017 ◽  
Vol 30 (2) ◽  
pp. 586-594 ◽  
Author(s):  
Ying Zhou ◽  
Guiping Lin ◽  
Xueqin Bu ◽  
Lizhan Bai ◽  
Dongsheng Wen
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Jet Impingement ◽  
Curvature Effects ◽  
Impingement Heat Transfer

Single-Phase and Boiling Cooling of Small Pin Fin Arrays by Multiple Nozzle Jet Impingement

1996 ◽  
Vol 118 (1) ◽  
pp. 21-26 ◽  
Author(s):  
David Copeland
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Single Phase ◽  
Jet Impingement ◽  
Transfer Coefficients ◽  
Pin Fin ◽  
Heat Transfer Coefficients ◽  
Aspect Ratios ◽  
Pin Fin Arrays

Experimental measurements of multiple nozzle submerged jet array impingement single-phase and boiling heat transfer were made using FC-72 and 1 cm square copper pin fin arrays, having equal width and spacing of 0.1 and 0.2 mm, with aspect ratios from 1 to 5. Arrays of 25 and 100 nozzles were used, with diameters of 0.25 to 1.0 mm providing nozzle area from 5 to 20 mm2 (5 to 20% of the heat source base area). Flow rates of 2.5 to 10 cm3/s (0.15 to 0.6 l/min) were studied, with nozzle velocities from 0.125 to 2 m/s. Single nozzles and smooth surfaces were also evaluated for comparison. Single-phase heat transfer coefficients (based on planform area) from 2.4 to 49.3 kW/m2 K were measured, while critical heat flux varied from 45 to 395 W/cm2. Correlations of the single-phase heat transfer coefficient and critical heat flux as functions of pin fin dimensions, number of nozzles, nozzle area and liquid flow rate are provided.

Jet Cooling at the Rim of a Rotating Disk

1979 ◽  
Vol 101 (1) ◽  
pp. 68-72 ◽  
Author(s):  
D. E. Metzger ◽  
W. J. Mathis ◽  
L. D. Grochowsky
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Jet Impingement ◽  
Rotating Disk ◽  
Impinging Jets ◽  
Turbine Engine ◽  
Transfer Rates ◽  
Jet Cooling ◽  
Geometric Conditions ◽  
Face Contour

Results are presented from an experimental study conducted to measure heat transfer rates at the rim of a rotating disk convectively cooled by impinging jets. The disk face contour radially inward from the rim is varied to simulate the geometric conditions found on gas turbine engine rotors. Heat transfer rates are found to be relatively unaffected by impingement for jet flowrates less than the order of one-tenth the disk pumping flow. Disk pumping flows are evaluated through the use of an analysis which accounts for the presence of the disk hub. At larger jet flowrates, heat transfer rates increase strongly with increasing jet flow, reaching two to three times the no-impingement values at jet flowrates approximately equal to the pumped flow. All the heat transfer results, both with and without jet impingement, are essentially unaffected by changes in the disk face contour.

Sign in / Sign up

Export Citation Format

Share Document