Foam-Metal Casing Treatment on an Axial Flow Compressor: Stability Improvement and Noise Reduction

2021 ◽  
pp. 1-66
Author(s):  
Dakun Sun ◽  
Jia Li ◽  
Xu Dong ◽  
Ruize Xu ◽  
Xiaofeng Sun
Keyword(s):  
Noise Reduction ◽  
Axial Compressor ◽  
Axial Flow ◽  
Performance Comparison ◽  
Stall Inception ◽  
Stall Margin ◽  
Casing Treatment ◽  
Foam Metal ◽  
Metal Casing ◽  
Flow Compressor

Abstract This paper concerns the stability improvement and noise reduction of an axial compressor caused by the foam metal casing treatment (FMCT). Three FMCTs with different PPI (pores per inch), 20, 35, and 50, are tested experimentally. Two installation locations of foam metal in casing are considered and investigated. At location 1, it is found that the FMCT improves the stall margin by 5.4%~8.7% and the attenuation of compressor noise is up to 5 dB. At location 2, the stall margin is extended by 22.2%~37.1% but increasing the noise mostly. Besides, foam metal at location 1 causes less efficiency loss than that in location 2. Based on the analysis in near-casing pressure distribution, spanwise performance comparison and stall inception, the mechanism of the FMCT for enhancing compressor stability is also discussed.

Effect of the Foam Metal Casing Treatment on a Low-Speed Axial Compressor

2020 ◽  
Author(s):  
Jia Li ◽  
Dakun Sun ◽  
Reize Xu ◽  
Xu Dong ◽  
Xiaofeng Sun
Keyword(s):  
Axial Compressor ◽  
Leading Edge ◽  
Metal Ring ◽  
Efficiency Loss ◽  
Stall Inception ◽  
Stall Margin ◽  
Casing Treatment ◽  
Foam Metal ◽  
Metal Casing ◽  
The Impact

Abstract Foam metal is a foam-like substance made out of metal and can be used in flow control, vibration damping and acoustic absorption mainly based on their special physical properties. A kind of foam metal casing treatment is proposed and tested in this study. The impact of the foam metal casing treatment on compressor stability and noise reduction are experimentally investigated. The foam metal selected in the experiments is constructed from ferronickel and its PPI (pores per inch) is 35. The foam metal casing treatment comprises annular support casing and foam metal ring. The effect of foam metal location on stability of the test compressor are investigated by placing shims in support casing. Both time-mean and high-response instrumentation are applied to capture the steady and unsteady compressor performances with the presence of the foam metal casing treatment. 20 microphones of G.R.A.S type are used to measure in-duct acoustic level of the compressor. It is found that the SMI (stall margin improvement) is 36.1% and the efficiency loss is 1.5% at location 7. When foam metal moves to rotor leading edge, the SMI as well as the efficiency loss are getting smaller. The optimal location in the experiments is location 4 where the SMI of compressor is 14.9% and the efficiency loss is 0.1%. The interaction of foam metal with flow in the blade tip region at these locations are investigated and presented in detail. The PSD (power spectrum density) analysis is carried out to show the unsteady signal development in stall inception. The noise attenuation varies in 0.18∼1.6 dB when foam metal is at different locations. Finally, the mechanism and application of the foam metal casing treatment are also discussed.

scholarly journals Axial Flow Compressor Stability Enhancement: Circumferential T-Shape Grooves Performance Investigation

Aerospace ◽  
2021 ◽  
Vol 8 (1) ◽  
pp. 12
Author(s):  
Marco Porro ◽  
Richard Jefferson-Loveday ◽  
Ernesto Benini
Keyword(s):  
Vortex Breakdown ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Suction Side ◽  
Treatment Technique ◽  
Tip Leakage Flow ◽  
Stall Inception ◽  
Stall Margin ◽  
Casing Treatment ◽  
Stall Margin Improvement

This work focuses its attention on possibilities to enhance the stability of an axial compressor using a casing treatment technique. Circumferential grooves machined into the case are considered and their performances evaluated using three-dimensional steady state computational simulations. The effects of rectangular and new T-shape grooves on NASA Rotor 37 performances are investigated, resolving in detail the flow field near the blade tip in order to understand the stall inception delay mechanism produced by the casing treatment. First, a validation of the computational model was carried out analysing a smooth wall case without grooves. The comparisons of the total pressure ratio, total temperature ratio and adiabatic efficiency profiles with experimental data highlighted the accuracy and validity of the model. Then, the results for a rectangular groove chosen as the baseline case demonstrated that the groove interacts with the tip leakage flow, weakening the vortex breakdown and reducing the separation at the blade suction side. These effects delay stall inception, improving compressor stability. New T-shape grooves were designed keeping the volume as a constant parameter and their performances were evaluated in terms of stall margin improvement and efficiency variation. All the configurations showed a common efficiency loss near the peak condition and some of them revealed a stall margin improvement with respect to the baseline. Due to their reduced depth, these new configurations are interesting because they enable the use of a thinner light-weight compressor case as is desirable in aerospace applications.

Influencing Parameters of Tip Blowing Interacting With Rotor Tip Flow

2016 ◽  
Vol 139 (2) ◽  
Author(s):  
Cyril Guinet ◽  
André Inzenhofer ◽  
Volker Gümmer
Keyword(s):  
Geometric Model ◽  
Axial Compressor ◽  
Axial Flow ◽  
Navier Stokes ◽  
Axial Position ◽  
Design Parameters ◽  
Stall Margin ◽  
Casing Treatment ◽  
Transonic Compressor ◽  
Casing Treatments

The design space of axial-flow compressors is restricted by stability issues. Different axial-type casing treatments (CTs) have shown their ability to enhance compressor stability and to influence efficiency. Casing treatments have proven to be effective, but there still is need for more detailed investigations and gain of understanding for the underlying flow mechanism. Casing treatments are known to have a multitude of effects on the near-casing 3D flow field. For transonic compressor rotors, these are more complex, as super- and subsonic flow regions alternate while interacting with the casing treatment. To derive design rules, it is important to quantify the influence of the casing treatment on the different tip flow phenomena. Designing a casing treatment in a way that it antagonizes only the deteriorating secondary flow effects can be seen as a method to enhance stability while increasing efficiency. The numerical studies are carried out on a tip-critical rotor of a 1.5-stage transonic axial compressor. The examined recirculating tip blowing casing treatment (TBCT) consists of a recirculating channel with an air off-take above the rotor and an injection nozzle in front of the rotor. The design and functioning of the casing treatment are influenced by various parameters. A variation of the geometry of the tip blowing, more specifically the nozzle aspect ratio, the axial position, or the tangential orientation of the injection port, was carried out to identify key levers. The tip blowing casing treatment is defined as a parameterized geometric model and is automatically meshed. A sensitivity analysis of the respective design parameters of the tip blowing is carried out on a single rotor row. Their impact on overall efficiency and their ability to improve stall margin are evaluated. The study is carried out using unsteady Reynolds-averaged Navier–Stokes (URANS) simulations.

Extensive Experimental Study of Circumferential Single Groove in an Axial Flow Compressor

2014 ◽  
Author(s):  
Jichao Li ◽  
Feng Lin ◽  
Sichen Wang ◽  
Juan Du ◽  
Chaoqun Nie ◽  
...  
Keyword(s):  
Experimental Study ◽  
Unsteady Flow ◽  
Axial Compressor ◽  
Axial Flow ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Good Tool ◽  
Stall Margin ◽  
Casing Treatment ◽  
Tip Leakage

Circumferential single-groove casing treatment becomes an interesting topic in recent few years, because it is a good tool to explore the interaction between the groove and the flow in blade tip region. The stall margin improvement (SMI) as a function of the axial groove location has been found for some compressors, such a trend cannot be predicted by steady high-fidelity CFD simulations. Recent efforts show that to catch such a trend, multi-passage, unsteady flow simulations are needed as the stalling mechanism itself involves cross-passage flows and unsteady dynamics. This indicates a need to validate unsteady numerical simulation results. In this paper, an extensive experimental study of a total of fifteen single casing grooves in a low-speed axial compressor rotor is presented, the groove location varies from 0.4% to 98.3% of axial tip chord are tested. The unsteady pressure data both at casing and at the blade wake with different groove locations are measured and processed, including the movement of trajectory of tip leakage flow, the evolution of unsteadiness of tip leakage flow (UTLF), the unsteady spectrum signature during the stall process, and the outlet unsteady flow characteristic along the span. These data provide a case study for validation of the unsteady CFD results, and may be helpful for further interpretation on the stalling mechanism affected by circumferential casing grooves.

scholarly journals Flow mechanism of affecting an axial flow compressor performance and stability with cross-blade slot casing treatments

2018 ◽  
Vol 233 (1) ◽  
pp. 17-36 ◽  
Author(s):  
HaoGuang Zhang ◽  
XuDong Zhang ◽  
YanHui Wu ◽  
WuLi Chu ◽  
HaiYang Kuang
Keyword(s):  
Axial Flow ◽  
Low Energy ◽  
Peak Efficiency ◽  
Stall Margin ◽  
Casing Treatment ◽  
Flow Loss ◽  
Stall Margin Improvement ◽  
And Performance ◽  
Flow Compressor ◽  
Casing Treatments

The objective of this study is to evaluate the effect of cross-blade slot casing treatment on the stability and performance of an axial flow compressor rotor. The experimental and unsteady calculated results both show that cross-blade slot casing treatment can generate about 22% stall margin improvement, and the compressor peak efficiency is reduced by about 13%. The detailed flow-field analyses indicate that the sucked and injected flow caused by the slots of cross-blade slot casing treatment can restrain the rotor tip passage blockage, which is made by the low energy tip clearance leakage vortex. When cross-blade slot casing treatment is applied, not only the rotor wheel flange work becomes lower in most of the rotor blade span, but also the flow loss in the blade tip passage becomes fairly large due to the strong interaction between the mainstream and the injected flows made by the slots. As a result, the compressor total pressure ratio and efficiency for cross-blade slot casing treatment are reduced obviously. Three kinds of new cross-blade slot casing treatment were designed according to the previous successful experience and investigated in this paper. The numerical results show that the new three cross-blade slot casing treatments both generate about 54% stall margin improvement at the cost of minor peak efficiency. For one new cross-blade slot casing treatment (CSCT2), the compressor peak efficiency is reduced by about 0.3%. The low energy TLV, which is present for cross-blade slot casing treatment, is removed by the strong sucked flow made by CSCT2. Moreover, the interaction between the mainstream and the injected flows caused by CSCT2 becomes weak obviously, and the corresponding flow loss is reduced greatly. Hence, the compressor stability and performance with CSCT2 are higher than those with cross-blade slot casing treatment.

Numerical Investigations of the Coupled Flow Through a Subsonic Compressor Rotor and Axial Skewed Slot

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
Xingen Lu ◽  
Wuli Chu ◽  
Junqiang Zhu ◽  
Yangfeng Zhang
Keyword(s):  
Axial Flow ◽  
Tip Clearance ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Casing Treatment ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Flow Through ◽  
Flow Compressor

In order to advance the understanding of the fundamental mechanisms of axial skewed slot casing treatment and their effects on the subsonic axial-flow compressor flow field, the coupled unsteady flow through a subsonic compressor rotor and the axial skewed slot was simulated with a state-of-the-art multiblock flow solver. The computational results were first compared with available measured data, that showed the numerical procedure calculates the overall effect of the axial skewed slot correctly. Then, the numerically obtained flow fields were interrogated to identify the physical mechanism responsible for improvement in stall margin of a modern subsonic axial-flow compressor rotor due to the discrete skewed slots. It was found that the axial skewed slot casing treatment can increase the stall margin of subsonic compressor by repositioning of the tip clearance flow trajectory further toward the trailing of the blade passage and retarding the movement of the incoming∕tip clearance flow interface toward the rotor leading edge plane.

The Effects on Stability, Performance, and Tip Leakage Flow of Recirculating Casing Treatment in a Subsonic Axial Flow Compressor

2016 ◽  
Author(s):  
Wei Wang ◽  
Wuli Chu ◽  
Haoguang Zhang ◽  
Yanhui Wu
Keyword(s):  
Axial Flow ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Stall Inception ◽  
Casing Treatment ◽  
Tip Leakage ◽  
Axial Flow Compressor ◽  
Overall Performance ◽  
Flow Compressor

Recirculating casing treatment (RCT) was studied in a subsonic axial flow compressor experimentally and numerically. The RCT was parameterized with the injector throat height and circumferential coverage percentage (ccp) to investigate its influence on compressor stability and on the overall performance in the experimentation. The injector throat height varied from 2 to 6 times the height of the rotor tip clearance, and the ccp ranged from 8.3% to 25% of the casing perimeter. Various RCT configurations were achieved with a modular design procedure. The rotor casing was instrumented with fast-response pressure transducers to detect the stall inception, rotational speed of stall cells, and pressure flow fields. Whole-passage unsteady simulations were also implemented for the RCT and solid casing to understand the flow details. Results indicate that both the compressor stability and overall performance can be improved through RCT with appropriate geometrical parameters. The effect of injector throat height on the stability depends on the choice of ccp, i.e., interaction effect exists. In general, the RCT with a moderate injector throat height and a large circumferential coverage is the optimal choice. Phase-locked pattern of the casing wall pressure reveals a weakened tip leakage vortex under the effect of RCT compared with the solid casing. The numerical results show that the RCT has a substantial effect on tip blockage even when the blade passages break away from the domain of RCT. The reduction of tip blockage induced by the tip leakage vortex is the main reason for the extension of stable operation range. The unsteadiness of double-leakage flow is detected both in the experiment and in numerical simulations. The pressure fluctuations caused by double-leakage flow are depressed with RCT. This observation indicates reduced losses related with the double-leakage flow. Although the stall inception is not changed by implementing RCT, the stall pattern is altered. The stall with two cells is detected in RCT compared with the solid casing with only one stall cell.

scholarly journals Improvement of Moderately Loaded Transonic Axial Compressor Performance Using Low Porosity Bend Skewed Casing Treatment

2014 ◽  
Vol 2014 ◽  
pp. 1-14 ◽  
Author(s):  
Dilipkumar Bhanudasji Alone ◽  
S. Satish Kumar ◽  
Shobhavathy M. Thimmaiah ◽  
Janaki Rami Reddy Mudipalli ◽  
A. M. Pradeep ◽  
...  
Keyword(s):  
Axial Compressor ◽  
Axial Flow ◽  
Experimental Results ◽  
Compressor Stage ◽  
Stall Margin ◽  
Casing Treatment ◽  
Plenum Chamber ◽  
Chamber Volume ◽  
Maximum Improvement ◽  
Low Porosity

This paper presents experimental results of a single stage transonic axial flow compressor coupled with low porosity bend skewed casing treatment. The casing treatment has a plenum chamber above the bend slots. The depth of the plenum chamber is varied to understand its impact on the performance of compressor stage. The performance of the compressor stage is evaluated for casing treatment and plenum chamber configurations at two axial locations of 20% and 40%. Experimental results reveal that the stall margin of the compressor stage increases with increase in the plenum chamber volume. Hot-wire measurements show significant reduction in the turbulence intensity with increase in the plenum chamber volume compared to that with the solid casing at the stall condition. At higher operating speeds of 80% and at 20% axial coverage, the stall margin of the compressor increases by 20% with half and full plenum depth. The improvement in the peak stage efficiency observed is 4.6% with half plenum configuration and 3.34% with the full plenum configuration. The maximum improvement in the stall margin of 29.16% is obtained at 50% operating speed with full plenum configurations at 40% axial coverage.

Experimental and numerical investigation of a subsonic compressor with bend-skewed slot-casing treatment

2006 ◽  
Vol 220 (12) ◽  
pp. 1785-1796 ◽  
Author(s):  
X Lu ◽  
W Chu ◽  
Y Zhang ◽  
J Zhu
Keyword(s):  
Rotor Blade ◽  
Axial Flow ◽  
Efficiency Gain ◽  
Stall Margin ◽  
Blade Passage ◽  
Casing Treatment ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Flow Compressor ◽  
Isentropic Efficiency

On the basis of the test results of discrete axial and blade angle slot casing treatment, a new type of casing treatment was designed for a subsonic axial flow compressor rotor by optimizing various geometry parameters. To obtain a wide operating range and to minimize penalties in terms of isentropic efficiency, seven compressor configurations incorporating casing treatments of 0, 16.6, 33.3, 50, 66.6, 83.3, and 100 per cent rotor exposures were experimentally investigated. The results showed that significant improvements in stall margin are possible in all exposures and insignificant isentropic efficiency sacrifices are recorded in some exposures. Nearly 21.43 per cent stall margin improvement in terms of the corrected mass flow-rate was achieved with 33.3 per cent rotor blade tip axial chord exposure. The compressor built with 16.6 per cent rotor exposure was the best configuration in terms of maximum isentropic efficiency gain. The second issue of the paper was to offer a contribution to the understanding of the physical mechanism by which bend-skewed slot-casing treatment improves stall margin under subsonic conditions. By applying a concept similar to ‘Domain scaling’ approach (as often used in multistage turbomachinery flow-fields) to the interface between the rotor blade passage and end-wall treatments, a time-dependent three-dimensional numerical simulation was performed for the subsonic axial-flow compressor rotor with bend-skewed slot-casing treatment. The numerical results agreed well with the available experimental results. Detailed analyses of the coupled flow through bend-skewed slot-casing treatment and rotor blade passage under subsonic conditions led to some preliminary conclusions as to the flow physics involved in the stall margin improvements afforded by the use of bend-skewed slot-casing treatment.

Sign in / Sign up

Export Citation Format

Share Document