scholarly journals Emissions Performance of Staged Premixed and Diffusion Combustor Concepts for an NH3/AIR Flame with and Without Reactant Humidification

2020 ◽  
Author(s):  
Daniel Pugh ◽  
Agustin Valera Medina ◽  
Philip Bowen ◽  
Anthony Giles ◽  
Burak Goktepe ◽  
...  
Keyword(s):  
High Speed ◽  
Equivalence Ratio ◽  
Nox Reduction ◽  
Secondary Process ◽  
Inlet Temperature ◽  
Numerical Comparison ◽  
Fuel Delivery ◽  
Secondary Air ◽  
Uncertain Supply ◽  
And Diffusion

Abstract Renewably generated ammonia offers a form of carbon-free chemical energy storage to meet the differences between uncertain supply and fluctuating demand and has the potential to support future energy requirements. The storage/transportation characteristics of NH3 are favourable compared with H2, however there are combustion research challenges to enhance fuel reactivity whilst reducing harmful emissions production. The purpose of this work was to evaluate different fuel delivery concepts for a representative GT combustor. An experimental and numerical comparison was made between swirl-stabilized premixed and diffusion NH3-air flames at elevated inlet temperature (473K). The exhaust NOx and NH3 emissions generated from each concept were quantified to optimize combustor performance. High-speed OH* and NH2* chemiluminescence was employed to characterize the change in flame topology with variation in fuel-air equivalence ratio, and the resultant influence on measured emission concentrations. Chemiluminescence intensities were shown to elucidate changes in sampled exhaust emissions, enabling detailed analysis of intermediate chemistry. A comparison was made between experimental data and kinetic simulations, demonstrating the sensitivity of NOx emissions to premixed fuel-air equivalence ratio. A comparison was also made between exclusive primary airflow, and the staged introduction of secondary air, to quantify the change in NOx production between each configuration and improve fuel burnout. Secondary air loadings were incrementally increased through the combustor. Finally, reactant humidification was employed as a secondary process for NOx reduction, having shown favourable performance with NH3-H2 mixtures, with the efficacy compared for both premixed and diffusion configurations.

scholarly journals Emissions Performance of Staged Premixed and Diffusion Combustor Concepts for an NH3/Air Flame With and Without Reactant Humidification

2020 ◽  
Author(s):  
D. Pugh ◽  
A. Valera-Medina ◽  
P. Bowen ◽  
A. Giles ◽  
B. Goktepe ◽  
...  
Keyword(s):  
High Speed ◽  
Equivalence Ratio ◽  
Nox Reduction ◽  
Exhaust Emissions ◽  
Secondary Process ◽  
Inlet Temperature ◽  
No Production ◽  
Numerical Comparison ◽  
Secondary Air ◽  
And Diffusion

Abstract Renewably generated ammonia offers a form of carbon-free chemical energy storage to meet the differences between uncertain renewable supply and fluctuating demand, and has the potential to support future energy requirements as a power-to-X concept. The storage and transportation characteristics of NH3 are favorable compared with H2, however there are significant combustion research challenges to enhance fuel reactivity whilst reducing harmful emissions production. The purpose of the presented work was to evaluate different fuel delivery concepts for a representative GT combustor. An experimental and numerical comparison was made between swirl-stabilized premixed and diffusion NH3-air flames at elevated inlet temperature (473 K). The exhaust NOx and unburned NH3 emissions generated from each concept were quantified to optimize operational combustor performance. High-speed OH* and NH2* chemiluminescence was employed to characterize the change in flame topology with variation in fuel-air equivalence ratio, and the resultant influence on measured emission concentrations. Chemiluminescence intensities were shown to elucidate changes in sampled exhaust emissions, enabling detailed analysis of intermediate chemistry. A comparison was made between experimental data and chemical kinetic simulations with a reactor network model, demonstrating the sensitivity of NOx emissions to premixed fuel-air equivalence ratio. A comparison was also made between exclusive primary airflow, and the staged introduction of secondary air, to quantify the change in NOx production between each configuration and improve fuel burnout. Secondary air loadings were incrementally increased through the combustor, and the change in exhaust emissions mapped. In addition, reactant humidification was employed as a secondary process for NOx reduction, having shown favorable performance with NH3/H2 mixtures to limit thermochemical NO production. The efficacy of humidification was compared for both premixed and diffusion configurations.

Passive Shroud Cooling Concepts for HP Turbines: CFD Based Design Approach

2006 ◽  
Author(s):  
E. Janke ◽  
F. Haselbach ◽  
C. Whitney ◽  
V. Kanjirakkad ◽  
R. Thomas ◽  
...  
Keyword(s):  
Film Cooling ◽  
High Speed ◽  
Flow Region ◽  
Design Approach ◽  
Inlet Temperature ◽  
Operational Parameters ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Secondary Air ◽  
Aerodynamic Losses

One option to improve the cycle efficiency of current state-of-the-art aero engines is to increase the turbine inlet temperature. Since this temperature is above the melting temperature for the alloys utilised in the turbine component already today, efficient cooling methods must be developed that consider both aerodynamic and aerothermal aspects of cooling. Here, the goal is to extract as little as possible secondary air from the main hot gas cycle for cooling and to use this coolant then aerodynamically and aerothermally as efficient as possible. The paper to be presented documents a CFD based design approach that lead to a new passive shroud cooling concept and the definition of its operational parameters. By using a simple one dimensional method [10] for predicting the aerodynamic losses resulting from such a cooling configuration in connection with 3d Navier-Stokes solvers (RANS) for predicting film cooling effectiveness contours on the rotor shroud surfaces, the new cooling configuration was developed. The concept was then tested and confirmed experimentally as documented in more detail in Part 2 of this paper. It is noted that only 70% of the coolant mass flow required for the current configuration was used for the new concept whereas the aerodynamic efficiency measured remained nearly constant. Improving upon existing passive shroud cooling systems where the coolant is injected directly into the labyrinth of the shroud, the new approach comprises cooling holes that inject the coolant upstream of the labyrinth and through the stator platform into the main passage flow. Here, it is important that the bulk of the coolant is placed below the dividing streamlines between main passage flow and labyrinth flow. Thereby, it can be achieved that the major part of the coolant indeed reaches the thermally loaded target surfaces on the shroud bottom at various axial gaps due to different operating points of the turbine. Besides the improved film-cooling effectiveness measured, the second important aspect of the new concept is the achievement of as small as possible additional aerodynamic losses due to coolant ejection into a high speed flow region. It will be shown that both goals can be achieved by the new concept. Furthermore, CFD results on film-cooling performance and aerodynamic losses will be shown and compared with experimental data.

Influence of Main Swirler Vane Angle on the Ignition Performance of TeLESS-II Combustor

2016 ◽  
Vol 139 (1) ◽  
Author(s):  
Bo Wang ◽  
Chi Zhang ◽  
Yuzhen Lin ◽  
Xin Hui ◽  
Jibao Li
Keyword(s):  
High Speed ◽  
Inlet Temperature ◽  
Main Stage ◽  
Ignition Process ◽  
High Speed Camera ◽  
Fuel Distribution ◽  
Fuel Droplets ◽  
Planar Laser ◽  
Cfd Method ◽  
Vane Angle

In order to balance the low emission and wide stabilization for lean premixed prevaporized (LPP) combustion, the centrally staged layout is preferred in advanced aero-engine combustors. However, compared with the conventional combustor, it is more difficult for the centrally staged combustor to light up as the main stage air layer will prevent the pilot fuel droplets arriving at igniter tip. The goal of the present paper is to study the effect of the main stage air on the ignition of the centrally staged combustor. Two cases of the main swirler vane angle of the TeLESS-II combustor, 20 deg and 30 deg are researched. The ignition results at room inlet temperature and pressure show that the ignition performance of the 30 deg vane angle case is better than that of the 20 deg vane angle case. High-speed camera, planar laser induced fluorescence (PLIF), and computational fluids dynamics (CFD) are used to better understand the ignition results. The high-speed camera has recorded the ignition process, indicated that an initial kernel forms just adjacent the liner wall after the igniter is turned on, the kernel propagates along the radial direction to the combustor center and begins to grow into a big flame, and then it spreads to the exit of the pilot stage, and eventually stabilizes the flame. CFD of the cold flow field coupled with spray field is conducted. A verification of the CFD method has been applied with PLIF measurement, and the simulation results can qualitatively represent the experimental data in terms of fuel distribution. The CFD results show that the radial dimensions of the primary recirculation zone of the two cases are very similar, and the dominant cause of the different ignition results is the vapor distribution of the fuel. The concentration of kerosene vapor of the 30 deg vane angle case is much larger than that of the 20 deg vane angle case close to the igniter tip and along the propagation route of the kernel, therefore, the 30 deg vane angle case has a better ignition performance. For the consideration of the ignition performance, a larger main swirler vane angle of 30 deg is suggested for the better fuel distribution when designing a centrally staged combustor.

Simulation of HCCI Combustion Characteristics for Low RON Gasoline Surrogate Fuels

2014 ◽  
Vol 694 ◽  
pp. 54-58
Author(s):  
Ling Zhe Zhang ◽  
Ya Kun Sun ◽  
Su Li ◽  
Qing Ping Zheng
Keyword(s):  
Equivalence Ratio ◽  
Chemical Kinetic ◽  
Combustion Characteristics ◽  
Material Strength ◽  
Inlet Temperature ◽  
Compression Ignition Engine ◽  
Chemical Kinetic Model ◽  
Hcci Engine ◽  
Surrogate Fuels ◽  
Inlet Conditions

A reduced chemical kinetic model (103species and 468 reactions) for new low-RON(research octane number) gasoline surrogate fuels has been proposed. Simulations explored for ignition delay time have been compared with experimental data in shock tubes at pressure of 10atm-55 atm and temperatue of 600-1400 K (fuel/air equivalence ratio=0.5,1.0,2.0 and EGR rate=0, 20%). The simulation data presented 15% enlargement compared with experiments showed applicability of the new kinetic mode in this work. A combustion simulation model has been build for HCCI(homogeneous charge compression ignition) engine with Chemkin-pro. The effects of different air inlet temperature, inlet pressure, engine speed and the fuel air equivalence ratio on the combustion characteristics of the fuel were researched. The results indicated the combustion in an HCCI engine worked sufficiently with lean mixtures and low speed. Meanwhile the material strength could be influenced when the inlet conditions changed. This helps to promote the low-RON gasoline surrogate fuel application in the HCCI engine.

Study on the Effect of Adiabatic Flame Temperature on NOx Formation Using Ethanol Gasoline Blend in SI Engine

2013 ◽  
Vol 781-784 ◽  
pp. 2471-2475 ◽  
Author(s):  
B. M. Masum ◽  
M.A. Kalam ◽  
H.H. Masjuki ◽  
S. M. Palash
Keyword(s):  
Equivalence Ratio ◽  
Gasoline Engine ◽  
Flame Temperature ◽  
Inlet Temperature ◽  
Si Engine ◽  
Nox Formation ◽  
Adiabatic Flame Temperature ◽  
No Formation ◽  
Blended Fuel ◽  
Active Research

Active research and development on using ethanol fuel in gasoline engine had been done for few decades since ethanol served as a potential of infinite fuel supply. This paper discussed analytically and provides data on the effects of compression ratio, equivalence ratio, inlet temperature, inlet pressure and ethanol blend in cylinder adiabatic flame temperature (AFT) and nitrogen oxide (NO) formation of a gasoline engine. Olikara and Borman routines were used to calculate the equilibrium products of combustion for ethanol gasoline blended fuel. The equilibrium values of each species were used to predict AFT and the NO formation of combustion chamber. The result shows that both adiabatic flame temperature and NO formation are lower for ethanol-gasoline blend than gasoline fuel.

Characteristics of Flame Bases for V-Gutters Stabilized Premixed Flames

2013 ◽  
Author(s):  
Fan Gong ◽  
Yong Huang
Keyword(s):  
Thermal Conductivity ◽  
Temperature Gradient ◽  
Equivalence Ratio ◽  
Premixed Flames ◽  
Flame Stabilization ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Heat Conducting ◽  
Inlet Velocity ◽  
The Impact

The objective of this work is to investigate the flame stabilization mechanism and the impact of the operating conditions on the characteristics of the steady, lean premixed flames. It’s well known that the flame base is very important to the existence of a flame, such as the flame after a V-gutter, which is typically used in ramjet and turbojet or turbofan afterburners and laboratory experiments. We performed two-dimensional simulations of turbulent premixed flames anchored downstream of the heat-conducting V-gutters in a confined passage for kerosene-air combustion. The flame bases are symmetrically located in the shear layers of the recirculation zone immediately after the V-gutter’s trailing edge. The effects of equivalence ratio of inlet mixture, inlet temperature, V-gutter’s thermal conductivity and inlet velocity on the flame base movements are investigated. When the equivalence ratio is raised, the flame base moves upstream slightly and the temperature gradient dT/dx near the flame base increases, so the flame base is strengthened. When the inlet temperature is raised, the flame base moves upstream very slightly, and near the flame base dT/dx increases and dT/dy decreases, so the flame base is strengthened. As the V-gutter’s thermal conductivity increases, the flame base moves downstream, and the temperature gradient dT/dx near the flame base decreases, so the flame base is weakened. When the inlet velocity is raised, the flame base moves upstream, and the convection heat loss with inlet mixture increases, so the flame base is weakened.

Experimental Investigation of Turbine Stage Flow Field and Performance at Varying Cavity Purge Rates and Operating Speeds

2016 ◽  
Author(s):  
Johan Dahlqvist ◽  
Jens Fridh
Keyword(s):  
Mach Number ◽  
Flow Field ◽  
High Speed ◽  
Control Volume ◽  
Spatial Average ◽  
Turbine Stage ◽  
Wide Range ◽  
Annulus Flow ◽  
Purge Flow ◽  
Secondary Air

The aspect of hub cavity purge has been investigated in a high-pressure axial low-reaction turbine stage. The cavity purge is an important part of the secondary air system, used to isolate the hot main annulus flow from cavities below the hub level. A full-scale cold-flow experimental rig featuring a rotating stage was used in the investigation, quantifying main annulus flow field impact with respect to purge flow rate as it was injected upstream of the rotor. Five operating speeds were investigated of which three with respect to purge flow, namely a high loading case, the peak efficiency, and a high speed case. At each of these operating speeds, the amount of purge flow was varied across a very wide range of ejection rates. Observing the effect of the purge rate on measurement plane averaged parameters, a minor outlet swirl decrease is seen with increasing purge flow for each of the operating speeds while the Mach number is constant. The prominent effect due to purge is seen in the efficiency, showing a similar linear sensitivity to purge for the investigated speeds. An attempt is made to predict the efficiency loss with control volume analysis and entropy production. While spatial average values of swirl and Mach number are essentially unaffected by purge injection, important spanwise variations are observed and highlighted. The secondary flow structure is strengthened in the hub region, leading to a generally increased over-turning and lowered flow velocity. Meanwhile, the added volume flow through the rotor leads to higher outlet flow velocities visible in the tip region, and an associated decreased turning. A radial efficiency distribution is utilized, showing increased impact with increasing rotor speed.

The Effect of Transient Fuel Staging on Self-Excited Instabilities in a Multi-Nozzle Model Gas Turbine Combustor

2017 ◽  
Author(s):  
Wyatt Culler ◽  
Janith Samarasinghe ◽  
Bryan D. Quay ◽  
Domenic A. Santavicca ◽  
Jacqueline O’Connor
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
High Speed ◽  
Equivalence Ratio ◽  
Growth Time ◽  
Stable Operation ◽  
Time Constants ◽  
Decay Times ◽  
Fuel Staging ◽  
Passive Techniques

Combustion instability in gas turbines can be mitigated using active techniques or passive techniques, but passive techniques are almost exclusively used in industrial settings. While fuel staging, a common passive technique, is effective in reducing the amplitude of self-excited instabilities in gas turbine combustors at steady-state conditions, the effect of transients in fuel staging on self-excited instabilities is not well understood. This paper examines the effect of fuel staging transients on a laboratory-scale five-nozzle can combustor undergoing self-excited instabilities. The five nozzles are arranged in a four-around-one configuration and fuel staging is accomplished by increasing the center nozzle equivalence ratio. When the global equivalence ratio is φ = 0.70 and all nozzles are fueled equally, the combustor undergoes self-excited oscillations. These oscillations are suppressed when the center nozzle equivalence ratio is increased to φ = 0.80 or φ = 0.85. Two transient staging schedules are used, resulting in transitions from unstable to stable operation, and vice-versa. It is found that the characteristic instability decay times are dependent on the amount of fuel staging in the center nozzle. It is also found that the decay time constants differ from the growth time constants, indicating hysteresis in stability transition points. High speed CH* chemiluminescence images in combination with dynamic pressure measurements are used to determine the instantaneous phase difference between the heat release rate fluctuation and the combustor pressure fluctuation throughout the combustor. This analysis shows that the instability onset process is different from the instability decay process.

scholarly journals Learning how: Body techniques, skill acquisition and the consumption of experience

2018 ◽  
Vol 19 (4) ◽  
pp. 425-445 ◽  
Author(s):  
Stephen Murphy ◽  
Maurice Patterson ◽  
Lisa O’Malley
Keyword(s):  
Skill Acquisition ◽  
Sustained Attention ◽  
High Speed ◽  
Empirical Investigation ◽  
Subject Formation ◽  
The Social ◽  
Body Techniques ◽  
And Diffusion

Although the skilful body has been ever-present in research accounts of consumption experiences, no sustained attention has been given to the acquisition of skills necessary for successful engagement with those experiences. In the present study, we report an empirical investigation of the acquisition and diffusion of embodied competencies among high-speed motorcyclists. In doing so, we mobilize the concept of reflexive body techniques in order to unpack the social, physical and mindful aspects of skilled embodiment. We demonstrate that skill acquisition is a necessary precursor to successful immersion into certain kinds of consumption experiences offered by the marketplace. Further, we underline the role of skill acquisition in subject formation.

Experimental Investigation of Combustion Dynamics in a Turbulent Syngas Combustor

2017 ◽  
Author(s):  
Nikhil Ashokbhai Baraiya ◽  
Baladandayuthapani Nagarajan ◽  
Satynarayanan R. Chakravarthy
Keyword(s):  
High Speed ◽  
Equivalence Ratio ◽  
Bluff Body ◽  
Dynamic Pressure ◽  
Fuel Mixture ◽  
High Amplitude ◽  
Acoustic Oscillations ◽  
Combustion Dynamics ◽  
Dynamic Pressure Measurement ◽  
Body Location

In the present work, the proportion of carbon monoxide to hydrogen is widely varied to simulate different compositions of synthesis gas and the potential of the fuel mixture to excite combustion oscillations in a laboratory-scale turbulent bluff body combustor is investigated. The effect of parameters such as the bluff body location and equivalence ratio on the self-excited acoustic oscillations of the combustor is studied. The flame oscillations are mapped by means of simultaneous high-speed CH* and OH* chemiluminescence imaging along with dynamic pressure measurement. Mode shifts are observed as the bluff body location or the air flow Reynolds number/overall equivalence ratio are varied for different fuel compositions. It is observed that the fuel mixtures that are hydrogen-rich excite high amplitude pressure oscillations as compared to other fuel composition cases. Higher H2 content in the mixture is also capable of exciting significantly higher natural acoustic modes of the combustor so long as CO is present, but not without the latter. The interchangeability factor Wobbe Index is not entirely sufficient to understand the unsteady flame response to the chemical composition.

Sign in / Sign up

Export Citation Format

Share Document