Exergy Analysis of Single-Effect Vapor Absorption System Using Design Parameters

2020 ◽  
Vol 143 (6) ◽  
Author(s):  
Khursheed Afroz Ansari ◽  
Md. Azhar ◽  
M. Altamush Siddiqui
Keyword(s):  
Energy Exchange ◽  
Operating Conditions ◽  
System Component ◽  
Design Parameters ◽  
Absorption System ◽  
Vapor Absorption ◽  
Shell And Tube ◽  
Single Effect ◽  
Internal Irreversibility ◽  
Control Volumes

Abstract In the present communication, internal irreversibility at each component of a single-effect vapor absorption refrigeration system has been evaluated and presented. The irreversibility is induced owing to the pressure drop in the shell and tube and energy exchange between the working fluids. Each component of the system is considered to be a shell and tube-type energy exchanger with slight modifications depending upon the applications. Each energy exchanger is divided into three control volumes, namely, tube wall, shell, and tube for which both energy and exergy balances are applied to evaluate the exergy destruction rate (EDR). Moreover, the overall EDR in the energy exchanger is then estimated in the form of pumping work and energy exchange duty. This objective function is further simplified in the form of design parameters such as tube diameter, friction coefficient, number of tubes, number of baffles, and overall heat transfer coefficient for the energy exchanger. In addition to this, optimum generator temperature and minimum EDR of each component of the absorption system have been tabulated and presented. Results show that for a single tube, UA value in the system component ranges from 2.99 W/K to 48.9 W/K depending on the operating conditions and design parameters of the system. Also, the number of tube in the system components ranges from 1108 tubes to 24803 tubes and the number of baffles in the respective components ranges from 2 to 7.

Performance Analyses of Photovoltaic Thermal Integrated Concentrator Collector Combined With Single Effect Absorption Cooling Cycle: Constant Flow Rate Mode

2020 ◽  
Vol 142 (12) ◽  
Author(s):  
Md. Meraj ◽  
M.E. Khan ◽  
Md. Azhar
Keyword(s):  
Climatic Conditions ◽  
Operating Conditions ◽  
Coefficient Of Performance ◽  
Design Parameters ◽  
Inlet Temperature ◽  
New Delhi ◽  
Absorption System ◽  
Simulation Code ◽  
Single Effect ◽  
Performance Analyses

Abstract In the present communication, performance analyses of interconnected N number of fully covered semitransparent photovoltaic thermal integrated concentrator collectors combined with single effect vapor absorption refrigeration system have been carried out. The proposed system was analyzed under the constant mass flowrate of collectors’ fluid. Mathematical expressions have also been derived for generator temperature of the absorption unit as a function of both design and operating parameters. Further, simulations have been performed for a typical day of May month of New Delhi climatic conditions. Performance parameters have been evaluated such as collector exit temperature, generator inlet temperature, electrical power output, electrical efficiency, overall thermal energy gain, instantaneous thermal efficiency, overall exergy gain and coefficient of performance of the absorption system. The simulation code has been written in matlab. From the present analyses, the following salient conclusions have been drawn: Operating generator temperature of the absorption system is suitable for five number of photovoltaic thermal-integrated parabolic concentrator collector connected in series. The proposed system will continue operating for 5 h during May month in New Delhi climate conditions. The maximum solar coefficient of performance, refrigeration coefficient of performance, and exergy coefficient of performance are reported as 0.1551, 0.8344, and 0.2697, respectively, for the proposed novel system under given design and operating conditions. Additionally, the effects of other design parameters of this novel system have also been investigated.

INFLUENCE OF THE SOLUTION HEAT EXCHANGER EFFICIENCY ON THE PERFORMANCE OF A SINGLE EFFECT H2O-LiBr ADIABATIC ABSORPTION SYSTEM

2011 ◽  
Vol 19 (02) ◽  
pp. 107-112 ◽  
Author(s):  
GEYDY GUTIÉRREZ URUETA ◽  
PEDRO RODRÍGUEZ AUMENTE ◽  
MARIA RODRÍGUEZ HIDALGO ◽  
ANTONIO LECUONA NEUMANN
Keyword(s):  
Heat Exchanger ◽  
Strong Solution ◽  
Heat Transfer Process ◽  
Operating Conditions ◽  
Coefficient Of Performance ◽  
Test Facility ◽  
Absorption System ◽  
Experimental Conditions ◽  
Single Effect ◽  
Absorption Cycle

This work analyzes the effect that particular operating conditions of a single effect H2O - LiBr adiabatic absorption system have on a plate-type solution heat exchanger efficiency. The corresponding influence of such efficiency on the performance of facility under study is evaluated. As a result of the design of experimental test facility, the functioning of the strong solution circuit leads to take into account some particular operating conditions which affect the correct performance of the solution heat exchanger. For some experimental conditions, the strong solution side is not completely filled by the solution fluid. As a consequence of this, the heat transfer process is affected, reducing the solution heat exchanger efficiency and changing greatly the resulting coefficient of performance (COP) of the absorption facility. In order to illustrate this phenomenon, this paper offers graphical results including: solution working temperatures, solution heat exchanger efficiency and COP in a time sequence of an experiment, as well as for fixed steady-state operating conditions. These results show the importance of a correct functioning of the solution heat exchanger on the performance of an absorption system. The results are useful for researchers interested in new absorption cycle designs.

Enhancement of the performance of bubble absorber using hybrid nanofluid as a cooled absorption system

2019 ◽  
Vol 29 (10) ◽  
pp. 3857-3871 ◽  
Author(s):  
Rawya Ben Jaballah ◽  
Mohamed Bechir Ben Hamida ◽  
Jehad Saleh ◽  
Mohammed A. Almeshaal
Keyword(s):  
Numerical Model ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Operating Conditions ◽  
Design Parameters ◽  
Hybrid Nanofluid ◽  
Absorption System ◽  
Content Type ◽  
Cooling Medium ◽  
High Heat Transfer

Purpose The purpose of this paper is to investigate the enhancement of the performance of bubble absorber using hybrid nanofluid as a cooled NH3/H2O absorption system to reduce their size and to find the best fitting model. A numerical model for ammonia-water bubble absorber was developed to show the influence of operating conditions and design parameters on the absorber performance. Design/methodology/approach A finite difference numerical method is used to solve the numerical model. The model is subjected to the inlet conditions of liquid, vapor and coolant flow regimes. The absorber modeling was divided into small elements along the absorber length. Findings The model proposed is validated with previously published works. Then agreement between the both is considered as good. Research limitations/implications Numerical results/The use of hybrid nanofluids. Originality/value The results showed that the hybrid nanofluid is the best cooling medium. Very high heat transfer rates are obtained because of the high thermal conductivity and specific heat of hybrid nanofluid, and consequently, the absorber size decreases. It was also found that the absorber thermal load and the mass absorption flux increase with increasing of solid volume fraction. Also, the existence of an optimal absorber length was revealed, required for complete absorption when using hybrid nanofluid as a cooling medium. It is recommended that using hybrid nanofluid to remove the heat from the absorber is the best candidate for NH3/H2O absorption performance enhancement.

scholarly journals Simulation of the Westinghouse AP1000 Response to SBLOCA Using RELAP/SCDAPSIM

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Ayah Elshahat ◽  
Timothy Abram ◽  
Judith Hohorst ◽  
Chris Allison
Keyword(s):  
Driving Forces ◽  
Natural Circulation ◽  
Safety System ◽  
Operating Conditions ◽  
Severe Accident ◽  
Passive Safety ◽  
System Component ◽  
Pressurized Water ◽  
Loss Of Coolant Accident ◽  
Accident Conditions

Great interest is given now to advanced nuclear reactors especially those using passive safety components. The Westinghouse AP1000 Advanced Passive pressurized water reactor (PWR) is an 1117 MWe PWR designed to achieve a high safety and performance record. The AP1000 safety system uses natural driving forces, such as pressurized gas, gravity flow, natural circulation flow, and convection. In this paper, the safety performance of the AP1000 during a small break loss of coolant accident (SBLOCA) is investigated. This was done by modelling the AP1000 and the passive safety systems employed using RELAP/SCDAPSIM code. RELAP/SCDAPSIM is designed to describe the overall reactor coolant system (RCS) thermal hydraulic response and core behaviour under normal operating conditions or under design basis or severe accident conditions. Passive safety components in the AP1000 showed a clear improvement in accident mitigation. It was found that RELAP/SCDAPSIM is capable of modelling a LOCA in an AP1000 and it enables the investigation of each safety system component response separately during the accident. The model is also capable of simulating natural circulation and other relevant phenomena. The results of the model were compared to that of the NOTRUMP code and found to be in a good agreement.

The Dynamic Modeling of PEMFC System for Automotive Application

2008 ◽  
Author(s):  
Sanggyu Kang ◽  
Kyoungdoug Min
Keyword(s):  
Energy Balance ◽  
Thermal Management ◽  
Dynamic Modeling ◽  
Management System ◽  
Mass Conservation ◽  
Cell System ◽  
Operating Conditions ◽  
Automotive Application ◽  
Thermal Management System ◽  
Control Volumes

Water and thermal management are crucial factors in determining the performance of PEMFC for automotive application. In order to investigate the effect of cell humidity and temperature on the performance of PEMFC, a dynamic model of a PEMFC system for automotive application has been developed by using Matlab/Simulink®. The model is composed of a PEM unit cell, membrane humidifier, and thermal management system (TMS). At first, fuel and air are well hydrated by the shell and tube humidifier, then humidified fuel and air flow into the PEMFC for electrochemical reaction. PEMFC temperature was maintained at a constant level by the thermal management system. The active area of PEM model is 240 cm2. The cell was discretized into several control volumes in the through-plane to resolve energy balance and species diffusion. The membrane humidifier model is also discretized into three control volumes in the through-plane to resolve the mass conservation and energy balance. Fuel and air are hydrated by the diffusion of the water through the membrane. The thermal management system consists of radiator, fan and pump. De-ionized water cools down the temperature of PEMFC. In order to validate the model, the model was compared with a corresponding experiment. Comparison shows that simulation results are in good agreement with experiments. And the dynamic response of PEMFC with regard to the change of current was also investigated. The model is useful to elucidate the relationships between operating conditions such as air relative humidity, temperature, etc. It is expected that this dynamic modeling of PEMFC system can contribute to the design optimization of PEM fuel cell system for vehicle application.

scholarly journals Binary Amplitude Reflection Gratings for X-ray Shearing and Hartmann Wavefront Sensors

Sensors ◽  
2021 ◽  
Vol 21 (2) ◽  
pp. 536
Author(s):  
Kenneth A. Goldberg ◽  
Antoine Wojdyla ◽  
Diane Bryant
Keyword(s):  
Operating Conditions ◽  
Design Parameters ◽  
Wavefront Aberration ◽  
Light Sources ◽  
Wavefront Sensors ◽  
X Ray ◽  
New Class ◽  
Coherent Wave ◽  
Reflection Gratings ◽  
Dynamic Operating

New, high-coherent-flux X-ray beamlines at synchrotron and free-electron laser light sources rely on wavefront sensors to achieve and maintain optimal alignment under dynamic operating conditions. This includes feedback to adaptive X-ray optics. We describe the design and modeling of a new class of binary-amplitude reflective gratings for shearing interferometry and Hartmann wavefront sensing. Compact arrays of deeply etched gratings illuminated at glancing incidence can withstand higher power densities than transmission membranes and can be designed to operate across a broad range of photon energies with a fixed grating-to-detector distance. Coherent wave-propagation is used to study the energy bandwidth of individual elements in an array and to set the design parameters. We observe that shearing operates well over a ±10% bandwidth, while Hartmann can be extended to ±30% or more, in our configuration. We apply this methodology to the design of a wavefront sensor for a soft X-ray beamline operating from 230 eV to 1400 eV and model shearing and Hartmann tests in the presence of varying wavefront aberration types and magnitudes.

Impact of Operating Conditions and Design Parameters on Gas Turbine Hot Section Creep Life

2010 ◽  
Author(s):  
S. Eshati ◽  
M. F. Abdul Ghafir ◽  
P. Laskaridis ◽  
Y. G. Li
Keyword(s):  
Gas Turbines ◽  
Performance Model ◽  
Operating Conditions ◽  
Creep Model ◽  
Design Parameters ◽  
Gas Temperature ◽  
Creep Life ◽  
Cooling Effectiveness ◽  
Radial Temperature ◽  
The Impact

This paper investigates the relationship between design parameters and creep life consumption of stationary gas turbines using a physics based life model. A representative thermodynamic performance model is used to simulate engine performance. The output from the performance model is used as an input to the physics based model. The model consists of blade sizing model which sizes the HPT blade using the constant nozzle method, mechanical stress model which performs the stress analysis, thermal model which performs thermal analysis by considering the radial distribution of gas temperature, and creep model which using the Larson-miller parameter to calculate the lowest blade creep life. The effect of different parameters including radial temperature distortion factor (RTDF), material properties, cooling effectiveness and turbine entry temperatures (TET) is investigated. The results show that different design parameter combined with a change in operating conditions can significantly affect the creep life of the HPT blade and the location along the span of the blade where the failure could occur. Using lower RTDF the lowest creep life is located at the lower section of the span, whereas at higher RTDF the lowest creep life is located at the upper side of the span. It also shows that at different cooling effectiveness and TET for both materials the lowest blade creep life is located between the mid and the tip of the span. The physics based model was found to be simple and useful tool to investigate the impact of the above parameters on creep life.

Numerical prediction of the performance of gas-lubricated spiral groove thrust bearings

1997 ◽  
Vol 211 (2) ◽  
pp. 117-128 ◽  
Author(s):  
Y Yue ◽  
T. A. Stolarski
Keyword(s):  
Control Volume ◽  
Numerical Procedure ◽  
Operating Conditions ◽  
Hydrodynamic Bearings ◽  
Thrust Bearings ◽  
Flow Balance ◽  
Control Volumes ◽  
Volume Method ◽  
Spiral Angle ◽  
Spiral Grooves

The objective of this paper is to develop an accurate numerical procedure for the analysis of nominally flat contacts with spiral grooves lubricated by gases. The numerical procedure, which is based on the control-volume method, enables the solutions of the non-linear Reynolds equation to be obtained without limitation in geometry and operating conditions. Satisfactory flow balance was achieved on the control volumes as well as on the whole boundary and the method was proved to be very accurate. Convergence of the method was quick for any compressibility number. Three types of contact with spiral grooves were analysed. They were hydrodynamic bearings without interior chambers, hydrodynamic bearings with interior chambers and hybrid bearings. The effects of spiral angle, groove geometry (length, depth and width) and compressibility on performances were investigated for all possible designs.

A Parametric Examination of the Factors Affecting the Performance of a Diffusion Absorption Refrigeration System

2021 ◽  
pp. 1-38
Author(s):  
Noman Yousuf ◽  
Timothy Anderson ◽  
Roy Nates
Keyword(s):  
Waste Heat ◽  
Operating Conditions ◽  
Design Parameters ◽  
Working Fluid ◽  
Low Grade ◽  
Absorption Refrigeration ◽  
Factors Affecting ◽  
Thermally Driven ◽  
Mass Flowrate ◽  
Diffusion Absorption

Abstract Despite being identified nearly a century ago, the diffusion absorption refrigeration (DAR) cycle has received relatively little attention. One of the strongest attractions of the DAR cycle lies in the fact that it is thermally driven and does not require high value work. This makes it a prime candidate for harnessing low grade heat from solar collectors, or the waste heat from stationary generators, to produce cooling. However, to realize the benefits of the DAR cycle, there is a need to develop an improved understanding of how design parameters influence its performance. In this vein, this work developed a new parametric model that can be used to examine the performance of the DAR cycle for a range of operating conditions. The results showed that the cycle's performance was particularly sensitive to several factors: the rate of heat added and the temperature of the generator, the effectiveness of the gas and solution heat exchangers, the mass flowrate of the refrigerant and the type of the working fluid. It was shown that can deliver good performance at low generator temperatures if the refrigerant mass fraction in the strong solution is made as high as possible. Moreover, it was shown that a H2O-LiBr working pair could be useful for achieving cooling at low generator temperatures.

A Practical Approach to Expedite a Pore to Process Simulation Model for a Rich Gas Condensate Reservoir – Case Study

2021 ◽  
Author(s):  
Mohamed Ibrahim Mohamed ◽  
Ahmed Mahmoud El-Menoufi ◽  
Eman Abed Ezz El-Regal ◽  
Ahmed Mohamed Ali ◽  
Khaled Mohamed Mansour ◽  
...  
Keyword(s):  
Simulation Model ◽  
Production Optimization ◽  
Operating Conditions ◽  
Gas Condensate ◽  
Western Desert ◽  
Design Parameters ◽  
Compositional Approach ◽  
Process Plant ◽  
Black Oil

Abstract Field development planning of gas condensate fields using numerical simulation has many aspects to consider that may lead to a significant impact on production optimization. An important aspect is to account for the effects of network constraints and process plant operating conditions through an integrated asset model. This model should honor proper representation of the fluid within the reservoir, through the wells and up to the network and facility. Obaiyed is one of the biggest onshore gas field in Egypt, it is a highly heterogeneous gas condensate field located in the western desert of Egypt with more than 100 wells. Three initial condensate gas ratios are existing based on early PVT samples and production testing. The initial CGRs as follows;160, 115 and 42 STB/MMSCF. With continuous pressure depletion, the produced hydrocarbon composition stream changes, causing a deviation between the design parameters and the operating parameters of the equipment within the process plant, resulting in a decrease in the recovery of liquid condensate. Therefore, the facility engineers demand a dynamic update of a detailed composition stream to optimize the system and achieve greater economic value. The best way to obtain this compositional stream is by using a fully compositional integrated asset model. Utilizing a fully compositional model in Obaiyed is challenging, computationally expensive, and impractical, especially during the history match of the reservoir numerical model. In this paper, a case study for Obaiyed field is presented in which we used an alternative integrated asset modeling approach comprising a modified black-oil (MBO) that results in significant timesaving in the full-field reservoir simulation model. We then used a proper de-lumping scheme to convert the modified black oil tables into as many components as required by the surface network and process plant facility. The results of proposed approach are compared with a fully compositional approach for validity check. The results clearly identified the system bottlenecks. The model can be used to propose the best tie-in location of future wells in addition to providing first-pass flow assurance indications throughout the field's life and under different network configurations. The model enabled the facility engineers to keep the conditions of the surface facility within the optimized operating envelope throughout the field's lifetime.

Sign in / Sign up

Export Citation Format

Share Document