Dynamic Metal Transfer Behavior in Double-Wire DP-GMAW of Aluminum Alloy Under Different Pulse Phases

2020 ◽  
Vol 143 (4) ◽  
Author(s):  
Kaiyuan Wu ◽  
Jiatong Zhan ◽  
Xuanwei Cao ◽  
Xiaobin Hong ◽  
Peimin Xie
Keyword(s):  
High Speed ◽  
Droplet Diameter ◽  
Gas Metal Arc Welding ◽  
Metal Transfer ◽  
Double Pulse ◽  
Droplet Growth ◽  
Al Alloy ◽  
Spray Transfer ◽  
Pulse Phase ◽  
Transfer Behavior

Abstract The effects of pulse phase and pulse stage on the metal transfer characteristics in double-wire double pulse gas metal arc welding (DP-GMAW) of aluminum (Al) alloy were studied using high-speed camera images and current and voltage waveforms. In addition, the effects of various forces on dynamic metal transfer behavior were analyzed under different pulse phases and pulse stages. The results show that the spray transfer mode can be obtained in both the alternating pulse phase (APP) and synchronous pulse phase (SPP). The transfer pattern of the leading and trailing droplets is alternating in the APP, but changes to simultaneous metal transfer in the SPP, mainly owing to influence of the pulse phase on droplet growth. The transfer type is one drop double pulse (ODDP) during the strong pulse stage and one drop triple pulse (ODTP) during the weak pulse stage, regardless of the pulse phase. The pulse phase does, however, affect the Lorentz force between the leading and trailing droplets, causing droplet collision in the SPP, which results in a poorer weld bead appearance compared with in the APP. Finally, the droplet diameter was found to be similar during different pulse phases and pulse stages.

Arc characteristics and metal transfer behavior of CMT+P process for Q235 steel of titanium-steel composite plate

2019 ◽  
Vol 33 (01n03) ◽  
pp. 1940040
Author(s):  
Yang Wang ◽  
Zhongyin Zhu ◽  
Guoqing Gou ◽  
Lin Peng ◽  
Yali Liu ◽  
...  
Keyword(s):  
High Speed ◽  
Short Circuit ◽  
Welding Process ◽  
Metal Transfer ◽  
Pulse Period ◽  
Cold Metal Transfer ◽  
Q235 Steel ◽  
Spray Transfer ◽  
Transfer Mode ◽  
Transfer Behavior

The cold metal transfer (CMT) with addition of pulses (CMT[Formula: see text]P) process is a new CMT welding method. This paper uses a high-speed camera and electrical signal synchronization acquisition system to perform a CMT[Formula: see text]P welding test on a 10 mm thick Q235 steel plate, and performs arc characteristic and droplet transfer behavior in the welding process. It has been founded that under relatively small currents and voltages, the CMT[Formula: see text]P transfer mode is a combination of a projected transfer mode with one droplet in the pulse period and a short circuit transfer mode during the CMT period. The process is stable with little spatter; at relatively large currents and voltages, the transition mode is the combination of pulse transfer, spray transfer and short circuit transfer. It results in one or more droplets that enter the pool both in pulse transfer in the spray transfer mode during the pulse period and in the short circuit transfer mode during the CMT period in a weld cycle.

scholarly journals Effects of active gases on droplet transfer and weld morphology in pulsed-current NG-GMAW of mild steel

2020 ◽  
Author(s):  
Guoqiang Liu ◽  
Xinhua Tang ◽  
Qi Xu ◽  
Fenggui Lu ◽  
Haichao Cui
Keyword(s):  
Mild Steel ◽  
High Speed ◽  
Gas Metal Arc Welding ◽  
Welding Process ◽  
Metal Transfer ◽  
Pulsed Current ◽  
Shielding Gas ◽  
Droplet Transfer ◽  
Spray Transfer ◽  
Pure Argon

Abstract Small amount of active gases CO 2 and O 2 were added into pure argon inert shielding gas to improve the weld formation of pulsed-current narrow-gap gas metal arc welding (NG-GMAW) of mild steel. Their effects on droplet transfer and arc behavior were investigated. A high-speed visual sensing system was utilized to observe the metal transfer process and arc morphology. When the proportion of CO 2 , being added into the pure argon shielding gas, changes from 5% to 5%, the metal transfer mode changes from pulsed spray streaming transfer to pulsed projected spray transfer, while it remains the pulsed spray streaming transfer when 2% to 10% O 2 is added. Both CO 2 and O 2 are favorable to stabilizing arc and welding process. O 2 is even more effective than CO 2 . However, O 2 is more likely to cause the inclusion defects in the weld, while CO 2 can improve the weld appearance in some sense. The weld surface concavity, which is sensitive to the formation of lack-of-fusion defect in NG-GMAW, is greatly influenced by the addition of active gas, but the weld width and weld penetration almost keep constant.

A Way to Weld Sheet Metal with Double-Electrode GMAW

2013 ◽  
Vol 651 ◽  
pp. 333-337 ◽  
Author(s):  
Guo Hong Ma ◽  
Yu Ming Zhang
Keyword(s):  
Arc Welding ◽  
High Speed ◽  
Gas Metal Arc Welding ◽  
Metal Transfer ◽  
Constant Current ◽  
Spray Transfer ◽  
Metal Arc Welding ◽  
Globular Transfer ◽  
Double Electrode ◽  
Welding System

This paper designed a double-electrode GMAW(gas metal arc welding) system. This system includes main arc and bypass arc. Main arc (Base metal current: Ibm) is supplied with Constant Current power (CC mode) and bypass arc (bypass current: Ibp) is Constant Voltage power (CV mode). Main arc electrode used common carbon wire, bypass arc electrode used water cool copper. Welding experiment shows this DE-GMAW can change common metal transfer into spray transfer with lowest critical total current (Itotal) 200 amps. When Ibm decreases and bypass voltage increases, this critical current will increase and it is less than 230 amps when keeping spray transfer. High speed video proved that metal transfer is changed from spray transfer to globular transfer.

Effect of Current Waveform on Metal Transfer in Controlled Short Circuiting Gas Metal Arc Welding

2013 ◽  
Vol 718-720 ◽  
pp. 202-208 ◽  
Author(s):  
Mao Ai Chen ◽  
Yuan Ning Jiang ◽  
Chuan Song Wu
Keyword(s):  
Transfer Process ◽  
High Speed ◽  
Gas Metal Arc Welding ◽  
Welding Current ◽  
Metal Transfer ◽  
Arc Voltage ◽  
Metal Arc Welding ◽  
Maximum Stability ◽  
The Stability ◽  
Welding Inverter

With high-speed welding inverter and precisely controlling the welding current with arc-bridge state, advanced pulse current waveforms can be produced to optimize the transfer characteristics of short circuiting transfer welding. In this paper, the images of droplet/wire, and the transient data of welding current and arc voltage were simultaneously recorded to study the influence of peak arcing current, background arcing current and tail-out time on the stability of short circuiting transfer process. It was found that maximum short circuiting transfer stability is reached under specific welding conditions. Any deviation from these conditions will cause abnormal rises in arc voltage indicating instantaneous arc extinguishing and greater spatter. Optimal welding conditions were obtained to achieve the maximum stability of short circuiting metal transfer process.

Mechanically assisted droplet transfer process in gas metal arc welding

2002 ◽  
Vol 216 (4) ◽  
pp. 555-564 ◽  
Author(s):  
Y Wu ◽  
R Kovacevic
Keyword(s):  
Transfer Process ◽  
Arc Welding ◽  
High Speed ◽  
Gas Metal Arc Welding ◽  
Metal Transfer ◽  
Droplet Transfer ◽  
Macroscopic Appearance ◽  
Transfer Mode ◽  
Metal Arc Welding ◽  
Separate Control

Gas metal arc welding has been generally accepted as the preferred joining technique due to its advantages in high production and automated welding applications. Separate control of arc energy and arc force is an essential way to improve the welding quality and to obtain the projected metal transfer mode. One of the most effective methods for obtaining separate control is to exert an additional force on the metal transfer process. In this paper, the droplet transfer process with additional mechanical force is studied. The welding system is composed of an oscillating wire feeder. The images of molten metal droplets are captured by a high-speed digital camera, and both the macroscopic appearance and the cross-sectional profiles of the weld beads are analysed. It is shown that the droplet transfer process can be significantly improved by wire electrode oscillation, and a projected spray transfer mode can be established at much lower currents. By increasing the oscillation frequency, the droplet transfer rate increases while the droplet size decreases. In addition, the improvement in the droplet transfer process with wire oscillation leads to an enhancement of the surface quality and a modification of the geometry of the weld beads that could be of importance for overlay cladding and rapid prototyping based on deposition by welding.

scholarly journals 3D Numerical Study of External Axial Magnetic Field-Controlled High-Current GMAW Metal Transfer Behavior

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5792
Author(s):  
Lei Xiao ◽  
Ding Fan ◽  
Jiankang Huang ◽  
Shinichi Tashiro ◽  
Manabu Tanaka
Keyword(s):  
Magnetic Field ◽  
Axial Magnetic Field ◽  
Numerical Study ◽  
Metal Transfer ◽  
Temperature Fields ◽  
Dominant Factor ◽  
Conductive Heat ◽  
High Current ◽  
Spray Transfer ◽  
Transfer Behavior

For gas metal arc welding (GMAW), increasing the welding current is the most effective way to improve welding efficiency. However, much higher current decreases the welding quality as a result of metal rotating-spray transfer phenomena in the high-current GMAW process. In this work, the external axial magnetic field (EAMF) was applied to the high-current GMAW process to control the metal transfer and decrease the welding spatters. A unified arc-droplet coupled model for high-current GMAW using EAMFs was built to investigate the metal rotating-spray transfer behavior. The temperature fields, flow fields in the arc, and droplet were revealed. Considering all the heat transferred to the molten metal, the Joule heat was found to be the dominant factor affecting the droplet temperature rise, followed by the anode heat. The conductive heat from the arc contributed less than half the value of the other two. Considering the EAMFs of different alternating frequencies, the arc constricting effects and controlled metal transfer behaviors are discussed. The calculated results agree well with the experimental high-speed camera observations.

Metal Transfer in Double-Electrode Gas Metal Arc Welding

2007 ◽  
Vol 129 (6) ◽  
pp. 991-999 ◽  
Author(s):  
Kehai Li ◽  
YuMing Zhang
Keyword(s):  
Base Metal ◽  
Arc Welding ◽  
High Speed ◽  
Gas Metal Arc Welding ◽  
High Melting ◽  
High Productivity ◽  
Spray Transfer ◽  
Metal Arc Welding ◽  
Double Electrode ◽  
Melting Current

Gas metal arc welding (GMAW) is the most widely used process for metal joining because of its high productivity and good quality, but analysis shows that the fundamental characteristic restricts conventional GMAW from further increasing the welding productivity. A novel GMAW process, refereed to as double-electrode GMAW or DE-GMAW, thus has been developed to make it possible to increase the melting current while the base metal current can still be controlled at a desired level. This fundamental change provides an effective method to allow manufacturers to use high melting currents to achieve high melting speed and low base metal heat input. A series of experiments have been conducted to uncover the basic characteristics of this novel process. Results obtained from analyses of high-speed image sequences and recorded current signals suggest that DE-GMAW can lower the critical current for achieving the desired spray transfer, shift the droplet trajectory, reduce the diameter of the droplet, and increase the speed and (generation) rate of the droplets.

Numerical analysis of the dynamic growth of droplets in gas metal arc welding

2000 ◽  
Vol 214 (10) ◽  
pp. 1247-1258 ◽  
Author(s):  
Y M Zhang ◽  
E Liguo
Keyword(s):  
Feedback Control ◽  
Transfer Process ◽  
Arc Welding ◽  
Gas Metal Arc Welding ◽  
Surface Tension Force ◽  
Metal Transfer ◽  
Force Balance ◽  
Droplet Growth ◽  
Metal Arc Welding ◽  
Control Technologies

Feedback control of droplet transfer is pursued as a solution to produce sound welds in gas metal arc welding. In previous work, a real-time visual system has been developed to monitor on line the droplet size and geometry. To realize feedback control of metal transfer, this study addresses the dynamic process of droplet growth and detachment. The droplet is subjected to gravitational force, electromagnetic force, plasma drag force and surface tension force. The geometry of the droplet is determined by these forces through the static force balance. However, the forces acting on the droplet continuously change as the melting electrode wire changes the droplet geometry. Because of this interdependence between the droplet geometry and the forces, the model must be solved dynamically and iteratively. A numerical program has been developed to acquire its dynamic numerical solution. Hence, the dynamics of the metal transfer process can be understood and simulated. Currently, this model is being used to simulate theclosed-loop controlled metal transfer process using different advanced control technologies.

scholarly journals Characteristics of Magnetic Field Assisting Plasma GMAW-P

2020 ◽  
Vol 99 (1) ◽  
pp. 25s-38s
Author(s):  
JIANG YU ◽  
◽  
BO WANG ◽  
HONGTAO ZHANG ◽  
PENG HE ◽  
...  
Keyword(s):  
Magnetic Field ◽  
High Speed ◽  
Gas Metal Arc Welding ◽  
Welding Current ◽  
Plasma Welding ◽  
Droplet Transfer ◽  
Spray Transfer ◽  
The Wire ◽  
Indirect Arc ◽  
The Magnetic Field

The droplet transfer and voltage-current characteristics of gas metal arc welding (GMAW) in single-pulsed GMAW (single GMAW-P), plasma pulsed GMAW (plasma GMAW-P), and plasma-GMAW-P with a magnetic field were studied using the synchronous acquisition system of high-speed camera and electric signals. The results showed the plasma arc and magnetic field had a significant effect on the droplet transfer process. The indirect arc of the plasma and gas metal arc emerged in the pulse peak phase causing a shunt phenomenon of the GMAW current. The period of the indirect arc was increased under the action of the magnetic field. In hybrid plasma GMAW-P, when the GMAW current did not exceed 140 A, several pulsed one-drop free transfers occurred and the droplet transfer period decreased with the increase in the plasma welding current; when the GMAW current exceeded 140 A, and the plasma welding current was less than 180 A, spray transfer was formed. The droplet transfer transformed into a projected transfer when the plasma welding current increased to 180 A. In plasma-GMAW-P hybrid welding with a magnetic field, the magnetic field had a slight effect on the transfer period. When the GMAW current did not exceed 140 A, the droplet transfer was mainly repelled transfer. The detaching location was on the right side of the wire when the magnetic field current was less than 3 A. When the magnetic field current exceeded 3 A, it was below or on the left side of the wire. When the GMAW current exceeded 140 A and the magnetic field current was less than 5 A, spray transfer was formed, but the droplet transfer mode transformed into a projected transfer with a magnetic field current of 5 A.

Sign in / Sign up

Export Citation Format

Share Document