scholarly journals Characteristics of Magnetic Field Assisting Plasma GMAW-P

2020 ◽  
Vol 99 (1) ◽  
pp. 25s-38s
Author(s):  
JIANG YU ◽  
◽  
BO WANG ◽  
HONGTAO ZHANG ◽  
PENG HE ◽  
...  
Keyword(s):  
Magnetic Field ◽  
High Speed ◽  
Gas Metal Arc Welding ◽  
Welding Current ◽  
Plasma Welding ◽  
Droplet Transfer ◽  
Spray Transfer ◽  
The Wire ◽  
Indirect Arc ◽  
The Magnetic Field

The droplet transfer and voltage-current characteristics of gas metal arc welding (GMAW) in single-pulsed GMAW (single GMAW-P), plasma pulsed GMAW (plasma GMAW-P), and plasma-GMAW-P with a magnetic field were studied using the synchronous acquisition system of high-speed camera and electric signals. The results showed the plasma arc and magnetic field had a significant effect on the droplet transfer process. The indirect arc of the plasma and gas metal arc emerged in the pulse peak phase causing a shunt phenomenon of the GMAW current. The period of the indirect arc was increased under the action of the magnetic field. In hybrid plasma GMAW-P, when the GMAW current did not exceed 140 A, several pulsed one-drop free transfers occurred and the droplet transfer period decreased with the increase in the plasma welding current; when the GMAW current exceeded 140 A, and the plasma welding current was less than 180 A, spray transfer was formed. The droplet transfer transformed into a projected transfer when the plasma welding current increased to 180 A. In plasma-GMAW-P hybrid welding with a magnetic field, the magnetic field had a slight effect on the transfer period. When the GMAW current did not exceed 140 A, the droplet transfer was mainly repelled transfer. The detaching location was on the right side of the wire when the magnetic field current was less than 3 A. When the magnetic field current exceeded 3 A, it was below or on the left side of the wire. When the GMAW current exceeded 140 A and the magnetic field current was less than 5 A, spray transfer was formed, but the droplet transfer mode transformed into a projected transfer with a magnetic field current of 5 A.

scholarly journals Effect of Alternating Magnetic Field on Arc Plasma Characteristics and Droplet Transfer during Narrow Gap Laser-MIG Hybrid Welding

Metals ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1712
Author(s):  
Baihao Cai ◽  
Juan Fu ◽  
Yong Zhao ◽  
Fugang Chen ◽  
Yonghui Qin ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Electron Temperature ◽  
High Speed ◽  
Stable State ◽  
Alternating Magnetic Field ◽  
Hybrid Welding ◽  
Arc Plasma ◽  
Narrow Gap ◽  
Droplet Transfer ◽  
The Magnetic Field

In this paper, the morphological characteristics of arc plasma and droplet transfer during the alternating magnetic field-assisted narrow gap groove laser-MIG (metal inert gas) hybrid welding process were investigated. The characteristics of arc plasma and droplet transfer, electron temperature, and density were analyzed using a high-speed camera and spectrum diagnosis. Our results revealed that the arc maintained a relatively stable state and rotated at a high speed to enhance the arc stiffness, and further improved the stability of the arc under the alternating magnetic field. The optimum magnetic field parameters in this experiment were B = 16 mT and f = 20 Hz, the electron temperature was 9893.6 K and the electron density was 0.99 × 1017 cm−3 near the bottom of the groove, which improved the temperature distribution inside the narrow gap groove and eliminated the lack of sidewall fusion defect. Compared to those without a magnetic field, the magnetic field could promote droplet transfer, the droplet diameter decreased by 17.6%, and the transition frequency increased by 23.5% (owing to the centrifugal force during droplet spinning and electromagnetic contraction force). The width of the weld bead was increased by 12.4% and the pores were also significantly reduced due to the stirring of the magnetic field on the molten pool.

scholarly journals Effects of active gases on droplet transfer and weld morphology in pulsed-current NG-GMAW of mild steel

2020 ◽  
Author(s):  
Guoqiang Liu ◽  
Xinhua Tang ◽  
Qi Xu ◽  
Fenggui Lu ◽  
Haichao Cui
Keyword(s):  
Mild Steel ◽  
High Speed ◽  
Gas Metal Arc Welding ◽  
Welding Process ◽  
Metal Transfer ◽  
Pulsed Current ◽  
Shielding Gas ◽  
Droplet Transfer ◽  
Spray Transfer ◽  
Pure Argon

Abstract Small amount of active gases CO 2 and O 2 were added into pure argon inert shielding gas to improve the weld formation of pulsed-current narrow-gap gas metal arc welding (NG-GMAW) of mild steel. Their effects on droplet transfer and arc behavior were investigated. A high-speed visual sensing system was utilized to observe the metal transfer process and arc morphology. When the proportion of CO 2 , being added into the pure argon shielding gas, changes from 5% to 5%, the metal transfer mode changes from pulsed spray streaming transfer to pulsed projected spray transfer, while it remains the pulsed spray streaming transfer when 2% to 10% O 2 is added. Both CO 2 and O 2 are favorable to stabilizing arc and welding process. O 2 is even more effective than CO 2 . However, O 2 is more likely to cause the inclusion defects in the weld, while CO 2 can improve the weld appearance in some sense. The weld surface concavity, which is sensitive to the formation of lack-of-fusion defect in NG-GMAW, is greatly influenced by the addition of active gas, but the weld width and weld penetration almost keep constant.

scholarly journals Arc Characteristics and Welding Process of Magnetic Field Assisting Plasma-GMAW-P

2021 ◽  
Vol 100 (01) ◽  
pp. 1-12
Author(s):  
JIANG YU ◽  
◽  
HONGTAO ZHANG ◽  
PENG HE ◽  
XIAO YANG ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Gas Flow ◽  
Gas Metal Arc Welding ◽  
Low Carbon Steel ◽  
Welding Process ◽  
Welding Current ◽  
Electrical Signal ◽  
Maximum Temperature ◽  
Low Carbon ◽  
The Magnetic Field

Low-carbon steel Q235B was successfully joined by plasma-pulsed gas metal arc welding (plasma-GMAW-P) with an external magnetic field. The arc profile, temperature field, electrical signal, microstructure, and mechanical properties of this method were analyzed. The results indicated that the coupling degree of the two arcs increased with the strengthening of the magnetic field current. However, when the magnetic field current was greater than 1 A, the arc pro-file changed slightly with the increase of the magnetic field current. Fixed on the magnetic field current, the coupling degree first increased and then decreased with the increase of the plasma welding current, GMAW-P welding current, plasma gas flow rate, and nozzle height, respectively. The maximum temperature had no obvious influence on joint penetration at different magnetic field cur-rents. However, the average temperature had an inverse effect on joint penetration at different magnetic field currents. The weld fusion zone joint tensile test results showed that the ratio of depth to width increased with the application of magnetic field currents. Moreover, tensile strength on the upper and lower part of the tensile samples were 521 and 488 MPa, respectively, which were 4.6% and 3.2% higher than those without the magnetic field. The microhardness of the weld joints was higher than that without the magnetic field.

Experimental investigation and optimization on field shaper structure parameters in magnetic pulse welding

2021 ◽  
pp. 095440542110148
Author(s):  
Yingzi Chen ◽  
Zhiyuan Yang ◽  
Wenxiong Peng ◽  
Huaiqing Zhang
Keyword(s):  
Magnetic Field ◽  
High Speed ◽  
Light Metal ◽  
Magnetic Pulse ◽  
Cross Sectional ◽  
Magnetic Pulse Welding ◽  
Pulse Welding ◽  
Sectional Shape ◽  
Welding System ◽  
The Magnetic Field

Magnetic pulse welding is a high-speed welding technology, which is suitable for welding light metal materials. In the magnetic pulse welding system, the field shaper can increase the service life of the coil and contribute to concentrating the magnetic field in the welding area. Therefore, optimizing the structure of the field shaper can effectively improve the efficiency of the system. This paper analyzed the influence of cross-sectional shape and inner angle of the field shaper on the ability of concentrating magnetic field via COMSOL software. The structural strength of various field shapers was also analyzed in ABAQUS. Simulation results show that the inner edge of the field shaper directly affects the deformation and welding effect of the tube. So, a new shape of field shaper was proposed and the experimental results prove that the new field shaper has better performance than the conventional field shaper.

Effect of Current Waveform on Metal Transfer in Controlled Short Circuiting Gas Metal Arc Welding

2013 ◽  
Vol 718-720 ◽  
pp. 202-208 ◽  
Author(s):  
Mao Ai Chen ◽  
Yuan Ning Jiang ◽  
Chuan Song Wu
Keyword(s):  
Transfer Process ◽  
High Speed ◽  
Gas Metal Arc Welding ◽  
Welding Current ◽  
Metal Transfer ◽  
Arc Voltage ◽  
Metal Arc Welding ◽  
Maximum Stability ◽  
The Stability ◽  
Welding Inverter

With high-speed welding inverter and precisely controlling the welding current with arc-bridge state, advanced pulse current waveforms can be produced to optimize the transfer characteristics of short circuiting transfer welding. In this paper, the images of droplet/wire, and the transient data of welding current and arc voltage were simultaneously recorded to study the influence of peak arcing current, background arcing current and tail-out time on the stability of short circuiting transfer process. It was found that maximum short circuiting transfer stability is reached under specific welding conditions. Any deviation from these conditions will cause abnormal rises in arc voltage indicating instantaneous arc extinguishing and greater spatter. Optimal welding conditions were obtained to achieve the maximum stability of short circuiting metal transfer process.

Mechanically assisted droplet transfer process in gas metal arc welding

2002 ◽  
Vol 216 (4) ◽  
pp. 555-564 ◽  
Author(s):  
Y Wu ◽  
R Kovacevic
Keyword(s):  
Transfer Process ◽  
Arc Welding ◽  
High Speed ◽  
Gas Metal Arc Welding ◽  
Metal Transfer ◽  
Droplet Transfer ◽  
Macroscopic Appearance ◽  
Transfer Mode ◽  
Metal Arc Welding ◽  
Separate Control

Gas metal arc welding has been generally accepted as the preferred joining technique due to its advantages in high production and automated welding applications. Separate control of arc energy and arc force is an essential way to improve the welding quality and to obtain the projected metal transfer mode. One of the most effective methods for obtaining separate control is to exert an additional force on the metal transfer process. In this paper, the droplet transfer process with additional mechanical force is studied. The welding system is composed of an oscillating wire feeder. The images of molten metal droplets are captured by a high-speed digital camera, and both the macroscopic appearance and the cross-sectional profiles of the weld beads are analysed. It is shown that the droplet transfer process can be significantly improved by wire electrode oscillation, and a projected spray transfer mode can be established at much lower currents. By increasing the oscillation frequency, the droplet transfer rate increases while the droplet size decreases. In addition, the improvement in the droplet transfer process with wire oscillation leads to an enhancement of the surface quality and a modification of the geometry of the weld beads that could be of importance for overlay cladding and rapid prototyping based on deposition by welding.

Metal Transfer in Double-Electrode Gas Metal Arc Welding

2007 ◽  
Vol 129 (6) ◽  
pp. 991-999 ◽  
Author(s):  
Kehai Li ◽  
YuMing Zhang
Keyword(s):  
Base Metal ◽  
Arc Welding ◽  
High Speed ◽  
Gas Metal Arc Welding ◽  
High Melting ◽  
High Productivity ◽  
Spray Transfer ◽  
Metal Arc Welding ◽  
Double Electrode ◽  
Melting Current

Gas metal arc welding (GMAW) is the most widely used process for metal joining because of its high productivity and good quality, but analysis shows that the fundamental characteristic restricts conventional GMAW from further increasing the welding productivity. A novel GMAW process, refereed to as double-electrode GMAW or DE-GMAW, thus has been developed to make it possible to increase the melting current while the base metal current can still be controlled at a desired level. This fundamental change provides an effective method to allow manufacturers to use high melting currents to achieve high melting speed and low base metal heat input. A series of experiments have been conducted to uncover the basic characteristics of this novel process. Results obtained from analyses of high-speed image sequences and recorded current signals suggest that DE-GMAW can lower the critical current for achieving the desired spray transfer, shift the droplet trajectory, reduce the diameter of the droplet, and increase the speed and (generation) rate of the droplets.

Study on Metal Transfer and Welding Spatter Characteristics of Basic Flux Cored Wire

2013 ◽  
Vol 477-478 ◽  
pp. 1369-1372 ◽  
Author(s):  
Yong Wang ◽  
Ying Qiao Zhang ◽  
Bao Wang ◽  
Zhi Jun Wang
Keyword(s):  
High Speed ◽  
Short Circuit ◽  
Welding Current ◽  
Metal Transfer ◽  
Welding Parameters ◽  
Droplet Transfer ◽  
Cored Wire ◽  
Basic Flux ◽  
Key Factor ◽  
Slag Column

The metal transfer behaviors of basic flux cored wire at different arc voltage and welding current and the resultant welding spatter were investigated by using a high speed camera. Two modes of metal transfer are found: globular repelled transfer (lower welding parameters) and small droplet transfer (higher welding parameters). The former is accompanied by large granular spatter, large droplet itself explosion spatter and electric explosive spatter of short-circuit, and spatter in the latter is reduced obviously. But if the slag column is found in the two models, spatter could be dropped evidently owing to its significant guiding role for metal transfer. Therefore the slag column is the key factor of reducing welding spatter.

Influence of Preset Pulsed Magnetic Field on Process Stability of Short Circuiting Transfer in Gas Metal Arc Welding

2011 ◽  
Vol 339 ◽  
pp. 440-443 ◽  
Author(s):  
Shu Jun Chen ◽  
Chang Hui Liu ◽  
Yang Yu ◽  
Shao Jun Bai
Keyword(s):  
Magnetic Field ◽  
Arc Welding ◽  
Short Circuit ◽  
Gas Metal Arc Welding ◽  
Welding Current ◽  
Pulsed Magnetic Field ◽  
Optimum Conditions ◽  
Horizontal Magnetic Field ◽  
Metal Arc Welding ◽  
Peak Value

This study proposed preset pulsed magnetic field acting on process of the short circuiting transfer. It is a controlled horizontal magnetic field which attached at the very beginning of contact between the wire and the weld pool during welding. It was found that there exists optimum conditions of magnetic field with which preset pulsed magnetic field could accelerate the rupture of the liquid bridge and reduce the peak value of welding current in the period of short circuiting transfer. This lead to energy accumulation lowered at the last phase of the short circuiting transfer and spatter loss reduced resulting from explosive short circuit rupture, in the meantime, it could improve the regularity and stability of the short circuiting transfer as well as the weld shaping quality.

Sign in / Sign up

Export Citation Format

Share Document