Mapping Efficiency of a Pulsing Flow-Driven Turbine

2020 ◽  
Vol 142 (6) ◽  
Author(s):  
Mark H. Fernelius ◽  
Steven E. Gorrell
Keyword(s):  
Pressure Pulse ◽  
Pressure Ratio ◽  
Pulse Amplitude ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Turbine Efficiency ◽  
Pressure Gain Combustion ◽  
Pulsing Flow ◽  
Cycle Efficiency ◽  
Flow Experiences

Abstract Pressure gain combustion (PGC) shows potential to increase the cycle efficiency of conventional gas turbine engines (GTEs) if used in place of the steady combustor. However, a turbine driven by pulsing flow experiences a decrease in efficiency. An experimental rig was built to compare a steady flow-driven turbine with a pulsing flow-driven turbine. The pressure pulse was a full annular, sinusoidal pressure pulse. The experimental data showed a decrease in turbine efficiency and pressure ratio. The pressure pulse amplitude and not the frequency was discovered to be the cause for the decrease in turbine efficiency for the current experimental setup. The decrease in turbine efficiency was mapped with turbine pressure ratio and corrected amplitude to demonstrate how the efficiency of a turbine under pulsing flow conditions could be mapped.

Predicting Efficiency of a Turbine Driven by Pulsing Flow

2017 ◽  
Author(s):  
Mark H. Fernelius ◽  
Steven E. Gorrell
Keyword(s):  
Computational Fluid Dynamic ◽  
Fluid Dynamic ◽  
Pulse Amplitude ◽  
Driving Factor ◽  
Dynamic Simulations ◽  
Turbine Engine ◽  
Turbine Efficiency ◽  
Pressure Gain Combustion ◽  
Pulsing Flow ◽  
Flow Experiences

One of the challenges of integrating pressure gain combustion into a gas turbine engine is that a turbine driven by pulsing flow experiences a decrease in efficiency. Computational fluid dynamic simulations validated with experiments showed that pulse amplitude is the driving factor for decreased turbine efficiency and not the pulsing frequency. A quadratic correlation between turbine efficiency and corrected pulse amplitude is presented. Incidence variation is shown to cause the change in turbine efficiency and a correlation between corrected incidence and corrected amplitude is shown to predict turbine efficiency.

The Effects of Ambient Conditions on Gas Turbine Emissions—Generalized Correction Factors

1978 ◽  
Vol 100 (4) ◽  
pp. 640-646 ◽  
Author(s):  
P. Donovan ◽  
T. Cackette
Keyword(s):  
Gas Turbine ◽  
Pressure Ratio ◽  
Turbine Engines ◽  
Inlet Temperature ◽  
Gas Turbine Engines ◽  
Correction Factors ◽  
Oxides Of Nitrogen ◽  
Ambient Conditions ◽  
Nitrogen Emission ◽  
Wide Range

A set of factors which reduces the variability due to ambient conditions of the hydrocarbon, carbon monoxide, and oxides of nitrogen emission indices has been developed. These factors can be used to correct an emission index to reference day ambient conditions. The correction factors, which vary with engine rated pressure ratio for NOx and idle pressure ratio for HC and CO, can be applied to a wide range of current technology gas turbine engines. The factors are a function of only the combustor inlet temperature and ambient humidity.

Thermo-Economic Optimization in the Design of Small-Scale and Residential Cogeneration Systems

2009 ◽  
Author(s):  
C. P. Lea˜o ◽  
S. F. C. F. Teixeira ◽  
A. M. Silva ◽  
M. L. Nunes ◽  
L. A. S. B. Martins
Keyword(s):  
Gas Turbine ◽  
Urban Areas ◽  
Pressure Ratio ◽  
Optimization Method ◽  
Turbine Engines ◽  
Small Scale ◽  
Inlet Temperature ◽  
Gas Turbine Engines ◽  
Economic Optimization ◽  
Micro Turbine

In recent years, gas-turbine engines have undergone major improvements both in efficiency and cost reductions. Several inexpensive models are available in the range of 30 to 250 kWe, with electrical efficiencies already approaching 30%, due to the use of a basic air-compressor associated to an internal air pre-heater. Gas-turbine engines offer significant advantages over Diesel or IC engines, particularly when Natural Gas (NG) is used as fuel. With the current market trends toward Distributed Generation (DG) and the increased substitution of boilers by NG-fuelled cogeneration installations for CO2 emissions reduction, small-scale gas turbine units can be the ideal solution for energy systems located in urban areas. A numerical optimization method was applied to a small-scale unit delivering 100 kW of power and 0.86 kg/s of water, heated from 318 to 353K. In this academic study, the unit is based on a micro gas-turbine and includes an internal pre-heater, typical of these low pressure-ratio turbines, and an external heat recovery system. The problem was formulated as a non-linear optimisation model with the minimisation of costs subject to the physical and thermodynamic constraints. Despite difficulties in obtaining data for some of the components cost-equations, the preliminary results indicate that the optimal compressor pressure ratio is about half of the usual values found in large installations, but higher than those of the currently available micro-turbine models, while the turbine inlet temperature remains virtually unchanged.

Design Study of an Advanced Concept Simple Gas Turbine for Possible Use in Low Emission Automobiles

1972 ◽  
Author(s):  
H. C. Eatock ◽  
M. D. Stoten
Keyword(s):  
High Pressure ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Simple Cycle ◽  
Turbine Engines ◽  
Nox Emissions ◽  
Preliminary Design ◽  
Gas Turbine Engines ◽  
High Pressure Ratio

United Aircraft Corporation studied the potential costs of various possible gas turbine engines which might be used to reduce automobile exhaust emissions. As part of that study, United Aircraft of Canada undertook the preliminary design and performance analysis of high-pressure-ratio nonregenerated (simple cycle) gas turbine engines. For the first time, high levels of single-stage component efficiency are available extending from a pressure ratio less than 4 up to 10 or 12 to 1. As a result, the study showed that the simple-cycle engine may provide satisfactory running costs with significantly lower manufacturing costs and NOx emissions than a regenerated engine. In this paper some features of the preliminary design of both single-shaft and a free power turbine version of this engine are examined. The major component technology assumptions, in particular the high pressure ratio centrifugal compressor, employed for performance extrapolation are explained and compared with current technology. The potential low NOx emissions of the simple-cycle gas turbine compared to regenerative or recuperative gas turbines is discussed. Finally, some of the problems which might be encountered in using this totally different power plant for the conventional automobile are identified.

scholarly journals A review of pollutants emissions in various pressure gain combustors

2019 ◽  
Vol 11 ◽  
pp. 175682771987072 ◽  
Author(s):  
Vijay Anand ◽  
Ephraim Gutmark
Keyword(s):  
Fluid Dynamic ◽  
Pollutant Emission ◽  
Turbine Engines ◽  
Thermodynamic Efficiency ◽  
Gas Turbine Engines ◽  
Wave Rotor ◽  
Pulse Detonation ◽  
Global View ◽  
Pressure Gain Combustion ◽  
Rotating Detonation

Recent years have witnessed a significant growth in the advancement and study of various unsteady combustors because of the prospective stagnation pressure gain offered by them. The pressure gain combustion produced by this class of combustors is poised to produce a step-change increase in the thermodynamic efficiency of gas-turbine engines. The current manuscript is oriented toward presenting a review on the pollutant emission characteristics of these devices; specifically, studies done so far on wave rotor combustors, pulsejet combustors, pulse detonation combustors, and rotating detonation combustors are evaluated. Because of the inherent fluid dynamic unsteadiness peculiar to pressure gain combustion devices, their emissions behavior is not well understood, and is notably different from the more conventional, steady combustors. The global view provided herein is expected to further the understanding of pressure gain combustion systems and ascertain the practicality of implementing them in real-world applications.

Advanced Multi-Cup Fuel Injector Technology for Environmentally Responsible Aviation Gas Turbine Engines

2015 ◽  
Author(s):  
Erlendur Steinthorsson ◽  
Adel Mansour ◽  
Brian Hollon ◽  
Michael Teter ◽  
Clarence Chang
Keyword(s):  
Gas Turbine ◽  
Direct Injection ◽  
Pressure Ratio ◽  
Test Facility ◽  
Turbine Engines ◽  
Practical Implementation ◽  
Gas Turbine Engines ◽  
Fuel Injector ◽  
Ambient Conditions ◽  
Environmentally Responsible

Participating in NASA’s Environmentally Responsible Aviation (ERA) Project, Parker Hannifin built and tested multipoint Lean Direct Injection (LDI) fuel injectors designed for NASA’s N+2 55:1 Overall Pressure-Ratio (OPR) gas turbine engine cycles. The injectors are based on Parker’s earlier three-zone injector (3ZI) which was conceived to enable practical implementation of multipoint LDI schemes in conventional aviation gas turbine engines. The new injectors offer significant aerodynamic design flexibility, excellent thermal performance, and scalability to various engine sizes. The injectors built for this project contain 15 injection points and incorporate staging to enable operation at low power conditions. Ignition and flame stability were demonstrated at ambient conditions with ignition air pressure drop as low as 0.3% and fuel-to-air ratio (FAR) as low as 0.011. Lean Blowout (LBO) occurred at FAR as low as 0.005 with air at 460 K and atmospheric pressure. A high pressure combustion testing campaign was conducted in the CE-5 test facility at NASA Glenn Research Center at pressures up to 250 psi and combustor exit temperatures up to 2,033 K (3,200 °F). The tests demonstrated estimated LTO cycle emissions that are about 30% of CAEP/6 for a reference 60,000 lbf thrust, 54.8-OPR engine. This paper presents some details of the injector design along with results from ignition, LBO and emissions testing.

Parameter Optimization on Combined Gas Turbine-Fuel Cell Power Plants

2005 ◽  
Vol 2 (4) ◽  
pp. 268-273 ◽  
Author(s):  
Rainer Kurz
Keyword(s):  
Fuel Cell ◽  
Gas Turbine ◽  
Power Plants ◽  
Pressure Ratio ◽  
Design Parameters ◽  
Turbine Efficiency ◽  
Compressor Pressure Ratio ◽  
Turbine Design ◽  
Cycle Efficiency ◽  
Compressor Efficiency

A thermodynamic model for a gas turbine-fuel cell hybrid is created and described in the paper. The effects of gas turbine design parameters such as compressor pressure ratio, compressor efficiency, turbine efficiency, and mass flow are considered. The model allows to simulate the effects of fuel cell design parameters such as operating temperature, pressure, fuel utilization, and current density on the cycle efficiency. This paper discusses, based on a parametric study, optimum design parameters for a hybrid gas turbine. Because it is desirable to use existing gas turbine designs for the hybrids, the requirements for this hybridization are considered. Based on performance data for a typical 1600hp industrial single shaft gas turbine, a model to predict the off-design performance is developed. In the paper, two complementary studies are performed: The first study attempts to determine the range of cycle parameters that will lead to a reasonable cycle efficiency. Next, an existing gas turbine, that fits into the previously established range of parameters, will be studied in more detail. Conclusions from this paper include the feasibility of using existing gas turbine designs for the proposed cycle.

A Mean Line Prediction Method for Axial Flow Turbine Efficiency

1982 ◽  
Vol 104 (1) ◽  
pp. 111-119 ◽  
Author(s):  
S. C. Kacker ◽  
U. Okapuu
Keyword(s):  
Gas Turbine ◽  
Axial Flow ◽  
Prediction Method ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Loss System ◽  
Turbine Efficiency ◽  
Wide Range ◽  
Line Loss ◽  
Axial Turbines

A mean line loss system is described, capable of predicting the design point efficiencies of current axial turbines of gas turbine engines. This loss system is a development of the Ainley/Mathieson technique of 1951. The prediction method is tested against the “Smith’s chart” and against the known efficiencies of 33 turbines of recent design. It is shown to be able to predict the efficiencies of a wide range of axial turbines of conventional stage loadings to within ± 1 1/2 percent.

scholarly journals ВПЛИВ ГУСТОТИ РЕШІТКИ НА АЕРОДИНАМІЧНУ НАВАНТАЖЕНІСТЬ РОБОЧОГО КОЛЕСА ОСЬОВОГО ВЕНТИЛЯТОРА

2020 ◽  
pp. 38-43
Author(s):  
Екатерина Викторовна Дорошенко ◽  
Михаил Владимирович Хижняк ◽  
Юрий Матвеевич Терещенко
Keyword(s):  
Gas Turbine ◽  
Pressure Ratio ◽  
Turbine Engines ◽  
Average Radius ◽  
Gas Turbine Engines ◽  
Axial Fan ◽  
Aerodynamic Loading ◽  
Wide Range ◽  
Axial Fans ◽  
Bypass Ratio

The main requirements that apply to axial fans and axial compressors of aircraft gas turbine engines include minimum dimensions and weight; high aerodynamic load; high coefficient of performance; wide range of steady work; high reliability. For gas turbine engines, the requirements of minimum weight and dimensions are especially important, since the engines must provide flights at high velocities and altitudes. This study aims to assess the effect of the solidity of the impeller fan on the average radius on the aerodynamic loading of the impeller of an axial fan for an engine with a high bypass ratio. The object of the study is the impeller of the fan. The solidity of the impeller fan on the average radius varied in the range from 1.8 to 0.82, the number of blades of the impeller fan varied from 33 to 15, respectively. The studies in this work were carried out by the method of numerical experiment. The flow in the axial fans was simulated by solving the system of Navier-Stokes equations, which were closed by the SST turbulent viscosity model. Based on the analysis of the results of the study, an assessment is made of the influence of the solidity of the impeller fan at an average radius on the aerodynamic loading of the impeller of an axial fan for an engine with a high bypass ratio. The research results showed that with a decrease in the solidity of the impeller fan at an average radius of 1.8 to 0.82 in operating modes with an axial inlet velocity of 80 to 120 m / s, the impeller fan pressure ratio decreases by 0.11 ... 3.2 %. The maximum decrease in the fan pressure ratio increase for the fan impeller with the parameters studied is 3.2 %, with a decrease in the number of fan blades from 33 to 15, while the total weight of the blades decreases by 54.55 %. The decrease in the solidity on the average radius of the impeller of the studied fan leads to a decrease in the relative sizes of the low-velocity zones at the sleeve and on the periphery and to a decrease in the level of flow unevenness. A further reduction in the level of flow non-uniformity behind the fan is possible when using the boundary layer control in the fan - this is the task of subsequent studies.

scholarly journals МЕТОД РАСЧЕТА ТЕРМОГАЗОДИНАМИЧЕСКИХ ПАРАМЕТРОВ ТУРБОВАЛЬНОГО ГТД НА ОСНОВЕ ПОВЕНЦОВОГО ОПИСАНИЯ ЛОПАТОЧНЫХ МАШИН. ЧАСТЬ 1. ОСНОВНЫЕ УРАВНЕНИЯ

2018 ◽  
pp. 48-58
Author(s):  
Людмила Георгиевна Бойко ◽  
Олег Владимирович Кислов ◽  
Наталия Владимировна Пижанкова
Keyword(s):  
Gas Turbine ◽  
Flow Rate ◽  
Pressure Ratio ◽  
Turbine Engines ◽  
Geometrical Parameters ◽  
Gas Turbine Engines ◽  
Balance Equations ◽  
Wide Range ◽  
In Series ◽  
Multistage Compressor

Gas turbine engines processes mathematic simulations are widely used in different steps of its living cycle. All engine simulations may be divided into different difficulty levels: higher simulation level allows doing a more pre­cise description of physical processes in main units of gas turbine engines and their elements. It gives the oppor­tunity for getting better arrangement of calculation results and experimental data, reduce the quality of factors, which are traditionally used in determine engine operational characteristics with 1-level models.The purpose of the article is to describe the thermogasdynamic parameters and maintenance perfomances cal­culation method, which based on second level mathematic simulation. Its main feature is blade-to-blade turbomachines description (multistage compressor and multistage cooling gas turbine), which allows to take into account blade and flow path geometrical parameters. Their changing during the gas turbine engine design and de­velopment processes influence its performances: thrust, fuel consumption, efficiency as functions of values of flow rate, rotational speed, engine entrance conditions and so on. All these dependences could be defined by using proposed calculation method.In distinction from methods which are noted, this method allows to concede compressor or turbine incidence angles, drag values, pressure ratio, surge margin in design and off-design  engine regimes. The opportunity to take into account by-passing and air bleeding from compressor blade channels and their engine parameters influence is very important also.The article includes calculation method main points, block-scheme, equations system, which gives the opportunity of alignment the engine units and their elements in wide range of state working regimes. Set of equations consists of flow rate balance equations through the stages of multistage compressor and turbine, combustion chamber and connected channels. Also system includes power balance equations, by-passing, air bleeding from compressor stages channels, its admission into the cooling turbine stages and ac­counts their thermodynamic parameters. Compressors and turbines maps parameters are calculated with main turbomachinery theory lows and semi-empirical dependences.This article is the first in series of articles, which considers this problem

Sign in / Sign up

Export Citation Format

Share Document