Parameter Optimization on Combined Gas Turbine-Fuel Cell Power Plants

2005 ◽  
Vol 2 (4) ◽  
pp. 268-273 ◽  
Author(s):  
Rainer Kurz
Keyword(s):  
Fuel Cell ◽  
Gas Turbine ◽  
Power Plants ◽  
Pressure Ratio ◽  
Design Parameters ◽  
Turbine Efficiency ◽  
Compressor Pressure Ratio ◽  
Turbine Design ◽  
Cycle Efficiency ◽  
Compressor Efficiency

A thermodynamic model for a gas turbine-fuel cell hybrid is created and described in the paper. The effects of gas turbine design parameters such as compressor pressure ratio, compressor efficiency, turbine efficiency, and mass flow are considered. The model allows to simulate the effects of fuel cell design parameters such as operating temperature, pressure, fuel utilization, and current density on the cycle efficiency. This paper discusses, based on a parametric study, optimum design parameters for a hybrid gas turbine. Because it is desirable to use existing gas turbine designs for the hybrids, the requirements for this hybridization are considered. Based on performance data for a typical 1600hp industrial single shaft gas turbine, a model to predict the off-design performance is developed. In the paper, two complementary studies are performed: The first study attempts to determine the range of cycle parameters that will lead to a reasonable cycle efficiency. Next, an existing gas turbine, that fits into the previously established range of parameters, will be studied in more detail. Conclusions from this paper include the feasibility of using existing gas turbine designs for the proposed cycle.

Effect of Bottoming Cycle Alternatives on the Performance of Combined Cycle

2003 ◽  
Author(s):  
R. Yadav
Keyword(s):  
Gas Turbine ◽  
Pressure Ratio ◽  
Positive Influence ◽  
Combined Cycle ◽  
Exhaust Temperature ◽  
Compressor Pressure Ratio ◽  
Topping Cycle ◽  
Steam Parameters ◽  
Cycle Efficiency ◽  
Steam Cycle

The increase in efficiency of combined cycle has mainly been caused by the improvements in gas turbine cycle efficiency. With the increase in firing temperature the exhaust temperature is substantially high around 873 K for moderate compressor pressure ratio, which has positive influence on steam cycle efficiency. Minimizing the irreversibility within the heat recovery steam generator HRSG and choosing proper steam cycle configuration with optimized steam parameters improve the steam cycle efficiency and thus in turn the combined cycle efficiency. In this paper, LM9001H gas turbine, a state of art technology turbine with modified compressor pressure ratio has been chosen as a topping cycle. Various bottoming cycles alternatives (sub-critical) coupled with LM9001H topping cycle with and without recuperation such as dual and triple pressure steam cycles with and without reheat have been chosen to predict the performance of combined cycle.

scholarly journals The Constant Volume Gas Turbine: A Thermodynamic Assessment

1974 ◽  
Author(s):  
M. Zockel
Keyword(s):  
Heat Exchanger ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Constant Pressure ◽  
Pressure Ratio ◽  
Constant Volume ◽  
Specific Power ◽  
Inlet Temperature ◽  
Turbine Efficiency ◽  
Compressor Pressure Ratio

A quasi-steady-state analysis is made of the performance of a gas-turbine working with intermittent, constant volume combustion. Variables considered include inlet temperature, compressor pressure ratio, scavenge ratio, combustion time, heat exchanger thermal ratio. Characteristics are computed over a full loading range. Computations are based on turbines having the following behavior: (a) constant turbine efficiency, (b) characteristics of a multistage axial turbine, and (c) characteristics of a single-stage radial turbine. The analysis indicates that the constant volume gas turbine has advantages in thermal efficiency, specific power and part load performance over constant pressure gas turbines operating at the same compressor pressure ratio and turbine inlet temperature. However, the addition of a heat exchanger shows less advantage when applied to a constant volume than to a constant pressure engine.

scholarly journals Scaling of an Aviation Hydrogen Micromix Injector Design for Industrial GT Combustion Applications

2021 ◽  
Author(s):  
Johannes Berger
Keyword(s):  
Renewable Energy ◽  
Gas Turbine ◽  
Power Plants ◽  
Supply And Demand ◽  
Pressure Ratio ◽  
Flame Temperature ◽  
Orifice Diameter ◽  
Design Parameters ◽  
Nox Emissions ◽  
The Impact

AbstractDecarbonising the energy grid through renewable energy requires a grid firming technology to harmonize supply and demand. Hydrogen-fired gas turbine power plants offer a closed loop by burning green hydrogen produced with excess power from renewable energy. Conventional dry low NOx (DLN) combustors have been optimized for strict emission limits. A higher flame temperature of hydrogen drives higher NOx emissions and faster flame speed alters the combustion behavior significantly. Micromix combustion offers potential for low NOx emissions and optimized conditions for hydrogen combustion. Many small channels, so-called airgates, accelerate the airflow followed by a jet-in-crossflow injection of hydrogen. This leads to short-diffusion flames following the principle of maximized mixing intensity and minimized mixing scales. This paper shows the challenges and the potential of an economical micromix application for an aero-derivative industrial gas turbine with a high-pressure ratio. A technology transfer based on the micromix combustion research in the ENABLEH2 project is carried out. The driving parameter for ground use adaption is an increased fuel orifice diameter from 0.3 mm to 1.0 mm to reduce cost and complexity. Increasing the fuel supply mass flow leads to larger flames and higher emissions. The impact was studied through RANS simulation and trends for key design parameters were shown. Increased velocity in the airgates leads to a higher pressure drop and reduced emissions through faster mixing. Altering the penetration depth shows potential for emission reduction without compromising on pressure loss. Two improved designs are found, and their performance is discussed.

Genetic Optimization of Steam Injected Gas Turbine Power Plants

2002 ◽  
Author(s):  
Ibrahim Sinan Akmandor ◽  
O¨zhan O¨ksu¨z ◽  
Sec¸kin Go¨kaltun ◽  
Melih Han Bilgin
Keyword(s):  
Gas Turbine ◽  
Power Output ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Power Plants ◽  
Pressure Ratio ◽  
Steam Injection ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Compressor Pressure Ratio

A new methodology is developed to find the optimal steam injection levels in simple and combined cycle gas turbine power plants. When steam injection process is being applied to simple cycle gas turbines, it is shown to offer many benefits, including increased power output and efficiency as well as reduced exhaust emissions. For combined cycle power plants, steam injection in the gas turbine, significantly decreases the amount of flow and energy through the steam turbine and the overall power output of the combined cycle is decreased. This study focuses on finding the maximum power output and efficiency of steam injected simple and combined cycle gas turbines. For that purpose, the thermodynamic cycle analysis and a genetic algorithm are linked within an automated design loop. The multi-parameter objective function is either based on the power output or on the overall thermal efficiency. NOx levels have also been taken into account in a third objective function denoted as steam injection effectiveness. The calculations are done for a wide range of parameters such as compressor pressure ratio, turbine inlet temperature, air and steam mass flow rates. Firstly, 6 widely used simple and combined cycle power plants performance are used as test cases for thermodynamic cycle validation. Secondly, gas turbine main parameters are modified to yield the maximum generator power and thermal efficiency. Finally, the effects of uniform crossover, creep mutation, different random number seeds, population size and the number of children per pair of parents on the performance of the genetic algorithm are studied. Parametric analyses show that application of high turbine inlet temperature, high air mass flow rate and no steam injection lead to high power and high combined cycle thermal efficiency. On the contrary, when NOx reduction is desired, steam injection is necessary. For simple cycle, almost full amount of steam injection is required to increase power and efficiency as well as to reduce NOx. Moreover, it is found that the compressor pressure ratio for high power output is significantly lower than the compressor pressure ratio that drives the high thermal efficiency.

scholarly journals Exergy and Exergoenvironmental Analysis of a CCHP System Based on a Parallel Flow Double-Effect Absorption Chiller

2016 ◽  
Vol 2016 ◽  
pp. 1-8 ◽  
Author(s):  
Ali Mousafarash
Keyword(s):  
Gas Turbine ◽  
Heat Recovery ◽  
Pressure Ratio ◽  
Design Parameters ◽  
Inlet Temperature ◽  
Heat Recovery Steam Generator ◽  
Absorption Chiller ◽  
Turbine Inlet Temperature ◽  
Compressor Pressure Ratio ◽  
Isentropic Efficiency

A combined cooling, heating, and power (CCHP) system which produces electricity, heating, and cooling is modeled and analyzed. This system is comprised of a gas turbine, a heat recovery steam generator, and a double-effect absorption chiller. Exergy analysis is conducted to address the magnitude and the location of irreversibilities. In order to enhance understanding, a comprehensive parametric study is performed to see the effect of some major design parameters on the system performance. These design parameters are compressor pressure ratio, gas turbine inlet temperature, gas turbine isentropic efficiency, compressor isentropic efficiency, and temperature of absorption chiller generator inlet. The results show that exergy efficiency of the CCHP system is higher than the power generation system and the cogeneration system. In addition, the results indicate that when waste heat is utilized in the heat recovery steam generator, the greenhouse gasses are reduced when the fixed power output is generated. According to the parametric study results, an increase in compressor pressure ratio shows that the network output first increases and then decreases. Furthermore, an increase in gas turbine inlet temperature increases the system exergy efficiency, decreasing the total exergy destruction rate consequently.

scholarly journals Investigation of the Pressure Gain Characteristics and Cycle Performance in Gas Turbines Based on Interstage Bleeding Rotating Detonation Combustion

Entropy ◽  
2019 ◽  
Vol 21 (3) ◽  
pp. 265 ◽  
Author(s):  
Lei Qi ◽  
Zhitao Wang ◽  
Ningbo Zhao ◽  
Yongqiang Dai ◽  
Hongtao Zheng ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Cycle Performance ◽  
Efficiency Enhancement ◽  
Compressor Pressure Ratio ◽  
Detonation Combustion ◽  
Gas Turbine Cycle ◽  
Cycle Efficiency ◽  
Rotating Detonation

To further improve the cycle performance of gas turbines, a gas turbine cycle model based on interstage bleeding rotating detonation combustion was established using methane as fuel. Combined with a series of two-dimensional numerical simulations of a rotating detonation combustor (RDC) and calculations of cycle parameters, the pressure gain characteristics and cycle performance were investigated at different compressor pressure ratios in the study. The results showed that pressure gain characteristic of interstage bleeding RDC contributed to an obvious performance improvement in the rotating detonation gas turbine cycle compared with the conventional gas turbine cycle. The decrease of compressor pressure ratio had a positive influence on the performance improvement in the rotating detonation gas turbine cycle. With the decrease of compressor pressure ratio, the pressurization ratio of the RDC increased and finally made the power generation and cycle efficiency enhancement rates display uptrends. Under the calculated conditions, the pressurization ratios of RDC were all higher than 1.77, the decreases of turbine inlet total temperature were all more than 19 K, the power generation enhancements were all beyond 400 kW and the cycle efficiency enhancement rates were all greater than 6.72%.

scholarly journals Analyses of Long-Term Off-Design Performance Strategy and Operation of a High-Pressure Ratio Intercooled Brayton Helium Gas Turbine Cycle for Generation IV Nuclear Power Plants

2018 ◽  
Vol 4 (4) ◽  
Author(s):  
A. Gad-Briggs ◽  
P. Pilidis ◽  
T. Nikolaidis
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Pressure Ratio ◽  
Pressure Losses ◽  
High Pressure Ratio ◽  
Compressor Pressure Ratio ◽  
Gas Turbine Cycle ◽  
Cycle Efficiency

The intercooled cycle (IC) is a simplified novel proposal for generation IV nuclear power plants (NPP) based on studies demonstrating efficiencies of over 45%. As an alternative to the simple cycle recuperated (SCR) and the intercooled cycle recuperated (ICR), the main difference in configuration is no recuperator, which reduces its size. It is expected that the components of the IC will not operate at optimum part power due to seasonal changes in ambient temperature and grid prioritization for renewable sources. Thus, the ability to demonstrate viable part load performance becomes an important requirement. The main objective of this study is to derive off-design points (ODPs) for a temperature range of −35 °C to 50 °C and core outlet temperatures (COTs) between 750 °C and 1000 °C. The ODPs have been calculated using a tool designed for this study. Based on the results, the intercooler changes the mass flow rate and compressor pressure ratio (PR). However, a drop of ∼9% in plant efficiency, in comparison to the ICR (6%) was observed for pressure losses of up to 5%. The reactor pressure losses for IC have the lowest effect on plant cycle efficiency in comparison to the SCR and ICR. Characteristic maps are created to support first-order calculations. It is also proposed to consider the intercooler pressure loss as a handle for ODP performance. The analyses brings attention to the IC an alternative cycle and aids development of cycles for generation IV NPPs specifically gas-cooled fast reactors (GFRs) and very-high-temperature reactors (VHTRs), using helium.

Environmental assessment of a hybrid system composed of solid oxide fuel cell, gas turbine and multiple effect evaporation desalination system

2020 ◽  
pp. 0958305X2097357
Author(s):  
Sobhan Jehandideh ◽  
Hasan Hassanzade ◽  
Seyyed Ehsan Shakib
Keyword(s):  
Fuel Cell ◽  
Gas Turbine ◽  
Pressure Ratio ◽  
Solid Oxide ◽  
Nox Emission ◽  
Emission Rates ◽  
Oxide Fuel ◽  
Exhaust Temperature ◽  
Desalination Plant ◽  
Compressor Pressure Ratio

This study deals with a solid oxide fuel cell- gas turbine (SOFC-GT) hybrid system coupled with a multi-effect evaporation desalination plant with steam condensation. The environmental evaluation is also done due to the importance of waste energy recovery especially waste heat in power generation systems. The evaporation desalination plant is studied for using the excess heat to produce freshwater. The thermodynamic relationships governing different components of the system are first provided, including fuel cells, heat exchangers, gas turbine, and desalination plant. Next, given the absence of previous research on the environmental effects of cogeneration systems, despite its necessity, the study system is analyzed from an environmental point of view. Accordingly, the impacts of the system performance parameters, including the fuel consumption coefficients, compressor pressure ratio, fuel pre-reforming percentage, and the steam to carbon ratio are investigated on the CO2, CO, and NOx emission rates. Based on the findings, it is concluded that of different species, the impacts of CO, CO2, and NOx emission rates are significant on the environment. Thus, the impacts of pressure ratio and pre-reforming percentage on their emission rates have been studied. The results revealed with increasing the compressor pressure ratio, increasing the fuel consumption coefficients, and decreasing the fuel cell's exhaust temperature, the CO and NOx emission rates and corresponding social costs diminished. On the other hand, with elevation of the ratio of steam to carbon, the recovery rate, the fuel cell's exhaust temperature, the concerned gas emission rates, and corresponding social costs increased.

scholarly journals Gas Turbine and Combined Cycle Technologies for Power and Efficiency Enhancement in Power Plants

1994 ◽  
Author(s):  
Meherwan P. Boyce ◽  
Cyrus B. Meher-Homji ◽  
A. N. Lakshminarasimha
Keyword(s):  
Gas Turbine ◽  
Power Plants ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Specific Work ◽  
Efficiency Enhancement ◽  
Turbine Inlet Temperature ◽  
Cycle Efficiency ◽  
Original Equipment Manufacturers

A wide variety of gas turbine based cycles exist in the market today with several technologies being promoted by individual Original Equipment Manufacturers. This paper is focused on providing users with a conceptual framework within which to view these cycles and choose suitable options for their needs. A basic parametric analysis is provided to show the interdependency of Turbine Inlet Temperature (TIT) and Pressure Ratio on cycle efficiency and specific work.

Performance Charateristics of Advanced Gas Turbine Cogeneration Power Plants

2005 ◽  
Author(s):  
Meherwan P. Boyce
Keyword(s):  
Steam Turbine ◽  
Gas Turbine ◽  
Firing Temperature ◽  
Gas Turbines ◽  
Heat Recovery ◽  
Power Plants ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Air Filter ◽  
Cycle Efficiency

The performance analysis of the new generation of Gas Turbines in combined cycle operation is complex and presents new problems, which have to be addressed. The new units operate at very high turbine firing temperatures. Thus variation in this firing temperature significantly affects the performance and life of the components in the hot section of the turbine. The compressor pressure ratio is high which leads to a very narrow operation margin, thus making the turbine very susceptible to compressor fouling. The turbines are also very sensitive to backpressure exerted on them by the heat recovery steam generators. The pressure drop through the air filter also results in major deterioration of the performance of the turbine. The performance of the combined cycle is also dependent on the steam turbine performance. The steam turbine is dependent on the pressure, temperature, and flow generated in the heat recovery steam generator, which in turn is dependent on the turbine firing temperature, and the air mass flow through the gas turbine. It is obvious that the entire system is very intertwined and that deterioration of one component will lead to off-design operation of other components, which in most cases leads to overall drop in cycle efficiency. Thus, determining component performance and efficiency is the key to determining overall cycle efficiency. Thermodynamic modeling of the plant with individual component analysis is not only extremely important in optimizing the overall performance of the plant but in also determining life cycle considerations.

Sign in / Sign up

Export Citation Format

Share Document