Condensation and Evaporation Heat Transfer Characteristics of Low Mass Fluxes in Horizontal Smooth Tube and Three-Dimensional Enhanced Tubes

2019 ◽  
Vol 12 (2) ◽  
Author(s):  
Xiang Ma ◽  
Wei Li ◽  
Chuan-cai Zhang ◽  
Zhi-chuan Sun ◽  
David J. Kukulka ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Mass Flux ◽  
Three Dimensional ◽  
Saturation Temperature ◽  
Transfer Enhancement ◽  
Heat Transfer Characteristics ◽  
Evaporation Heat ◽  
Enhanced Tubes ◽  
Evaporation Heat Transfer ◽  
Enhanced Surface

Abstract An experimental investigation of condensation and evaporation heat transfer characteristics was performed in 15.88-mm-OD and 12.7-mm-OD smooth and three-dimensional enhanced tubes (1EHT, 3EHT) using R134A and R410A as the working fluid. The enhanced surface of the 1EHT tube is made up of dimples and a series of petal arrays; while the 3EHT tube is made up of rectangular cavities. Evaluations are performed at a saturation temperature of 45 °C, over the quality range of 0.8–0.2 for condensation; while for evaporation the saturation temperature was 6 °C and the quality ranged from 0.2 to 0.8. For condensation, the enhancement ratio (enhanced tube/smooth tube) of the heat transfer coefficients was 1.42–1.95 for the mass flux ranging from 80 to 200 kg/m2s; while for evaporation, the heat transfer enhancement ratio is 1.05–1.42 for values of mass flux that range from 50 to 180 kg/m2s. Furthermore, the 1EHT tube provides the best condensation and evaporation heat transfer performance, for both working fluids at the mass flux considered. This performance is due to the dimples in the enhanced surface that produce interface turbulence; additionally, the increased surface roughness causes additional disturbances and secondary flows near the boundary, producing higher heat fluxes. The main objective of this study was to evaluate the heat transfer enhancement of two enhanced tubes when using R134A and R410A as a function of mass flux, saturation temperature, and tube diameter. As a result of this study, it was determined that the heat transfer coefficient decreases with an increase in saturation temperature and tube diameter.

Condensation and Evaporation Heat Transfer Characteristics in Horizontal Smooth and Three-Dimensional Enhanced Tubes

2020 ◽  
Author(s):  
Jianghui Zhang ◽  
Yu Guo ◽  
Chuancai Zhang ◽  
Yan He ◽  
David J. Kukulka ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Three Dimensional ◽  
Saturation Temperature ◽  
Secondary Flows ◽  
Outer Diameter ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Evaporation Heat ◽  
Enhanced Tubes ◽  
Evaporation Heat Transfer

Abstract An experimental investigation of condensation and evaporation heat transfer characteristics was performed in a smooth tube and two enhanced tubes (1EHT, 3EHT) using R134A as refrigerant. All tested tubes have the same inner diameter of 14.68mm and outer diameter of 15.88mm. The enhanced surface of the 1EHT tube is made up by dimples and a series of petal arrays, while that of 3EHT tube is rectangular cavities. The test runs are performed at a saturation temperature of 45°C, over the quality range of 0.8–0.2 for condensation and at a saturation temperature of 6°C, over the quality range of 0.1–0.6 for evaporation. For evaporation, the heat transfer coefficient ratio (hEHT/hs) is approximately 1.2–1.4 for mass from 50–90 kg/m2s. For condensation, the 1EHT tube provides the best condensation heat transfer performance. This is mainly due to the dimples and rectangular cavities that increase heat transfer surface area and interface turbulence, producing additional disturbances, secondary flows near the boundary and flow separation.

Experimental Study on Flow Evaporation Heat Transfer Characteristics Inside Horizontal Three-Dimensional Enhanced Tubes

2018 ◽  
Author(s):  
Wei Li ◽  
Chuancai Zhang ◽  
Zhichuan Sun ◽  
Zhichun Liu ◽  
Lianxiang Ma ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Mass Flux ◽  
Three Dimensional ◽  
Outer Diameter ◽  
Evaporation Heat ◽  
Enhanced Tubes ◽  
Evaporation Heat Transfer ◽  
The Heat Transfer Coefficient

Experimental investigation was performed to measure the evaporation heat transfer coefficients of R410A inside three three-dimensional enhanced tubes (1EHT-1, 1EHT-2 and 4LB). The inner and outer enhanced surface of the 4LB tube is composed by arrays of grooves and square pits, while 1EHT-1 tube and 1EHT-2 tube consist of longitudinal ripples and dimples of different depths. All these tubes have an inner diameter of 8.32 mm and an outer diameter of 9.52 mm. Experiment operational conditions are conducted as follows: the saturation temperature is 279 K, the vapor quality ranges from 0.2 to 0.8, and the mass flux varies from 160 kg/(m2·s) to 380 kg/(m2·s). With the mass flux increasing, the heat transfer coefficient increases accordingly. The heat transfer coefficient of 1EHT-2 is the highest of all three tubes, and that of 1EHT-1 is the lowest. The heat transfer coefficient of 4LB ranks between the 1EHT-1 and 1EHT-2 tube. The reason is that the heat transfer areas of the 1EHT-2 and 4LB tube are larger than that of 1EHT-1 and interfacial turbulence is enhanced in 1EHT-2.

Evaporation Heat Transfer and Pressure Drop of R-410A in a 5.0 mm O.D. Smooth and Microfin Tube

2015 ◽  
Vol 23 (01) ◽  
pp. 1550004 ◽  
Author(s):  
Nae-Hyun Kim
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Mass Flux ◽  
Saturation Temperature ◽  
Helix Angle ◽  
Apex Angle ◽  
Transfer Enhancement ◽  
Penalty Factor ◽  
Evaporation Heat ◽  
Evaporation Heat Transfer

R-410A's evaporation heat transfer and pressure drop data are provided for a 5.1 mm O.D. microfin tube having 40 fins with 18° helix angle and 40° fin apex angle. Tests were conducted for a range of quality (0.2–0.6), mass flux (260–433 kg/m2s), heat flux (10–20 kW/m2) and saturation temperature (8–12°C). Data are compared with smooth tube counterpart. It was found that both heat transfer coefficient and pressure drop increased as mass flux increased. The range of pressure drop penalty factor (1.10–1.70) was slightly smaller than that of heat transfer enhancement factor (1.39–1.79). Data are compared with available heat transfer and pressure drop correlations.

Experimental Study of Condensation Flow Inside Horizontal Smooth, Herringbone and Three Enhanced Surface Tubes

2017 ◽  
Author(s):  
Xiaolong Yan ◽  
Wei Li ◽  
Weiyu Tang ◽  
Hua Zhu ◽  
Zhijian Sun ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Mass Flux ◽  
Saturation Temperature ◽  
Horizontal Tube ◽  
Working Fluid ◽  
Experimental Investigations ◽  
Enhancement Effect ◽  
Two Phase ◽  
Inner Diameter ◽  
Enhanced Surface

Enhanced condensation heat transfer of two-phase flow on the horizontal tube side receives more and more concerns for its fundamentality and importance. Experimental investigations on convective condensation were performed respectively in different horizontal tubes: (i) a smooth tube (11.43 mm, inner diameter); (ii) a herringbone tube (11.43 mm, fin root diameter); and (iii) three enhanced surface (EHT) tubes (11.5 mm, equivalent inner diameter): 1EHT tube, 2EHT-1 tube and 2EHT-2 tubes. The surface of EHT tubes is enhanced by arrays of dimples with the background of petal arrays. Experiments were conducted at a saturation temperature of approximately 320 K; 0.8 inlet quality; and 0.2 outlet quality; 72–181 kg·m−2·s−1 mass flux using R22, R32 and R410A as the working fluid. The refrigerant R32 presents great heat transfer performance than R410A and R22 at low mass flux due to its higher latent heat of vaporization and larger thermal conductivity. The heat enhancement ratio of the herringbone tube is 2.72–2.82, rated number one. The primary dimples on the EHT tube increase turbulence and flow separation, and the secondary petal pattern produce boundary layer disruption to many smaller scale eddies. The 2EHT tubes are inferior to the 1EHT tube. A performance factor is used to evaluate the enhancement effect except of the contribution of area increase.

Evaporation Heat Transfer Characteristics on the Outside of Horizontal Smooth, Herringbone and Enhanced Surface 1EHT Tubes

2015 ◽  
Author(s):  
Jian-jun Sun ◽  
Jing-xiang Chen ◽  
David J. Kukulka ◽  
Kan Zhou ◽  
Wei Li ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Smooth Tube ◽  
External Diameter ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Mass Fluxes ◽  
Evaporation Heat ◽  
Evaporation Heat Transfer ◽  
Enhanced Surface

An experiment investigation was performed using R410A in order to determine the single-phase and evaporation heat transfer coefficients on the outside of (i) a smooth tube; (ii) herringbone tube; and (iii) the newly developed Vipertex enhanced surface 1EHT tube; all with the same external diameter (12.7 mm). The nominal evaporation temperature is 279 K, with inlet and outlet qualities of 0.1 and 0.8. Mass fluxes ranged from 10 to 40 kg m−2s−1. Results suggest that the 1EHT tube has excellent heat transfer performance but a higher pressure drop when compared to a smooth tube. Evaporation heat transfer coefficient for the 1EHT is lower than the herringbone tube and the pressure drop is almost the same.

An Experimental Study on Evaporation Heat Transfer Outside Horizontal Enhanced Tubes

2021 ◽  
Author(s):  
Zeguan Dong ◽  
Gu Zongbao ◽  
Xiang Ma ◽  
Wei Li ◽  
Yan He ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Evaporation Heat ◽  
Enhanced Tubes ◽  
Evaporation Heat Transfer

Predicting Heat Transfer in Long R-134a Filled Thermosyphons

2009 ◽  
Vol 131 (5) ◽  
Author(s):  
M. H. M. Grooten ◽  
C. W. M. van der Geld
Keyword(s):  
Heat Transfer ◽  
Saturation Temperature ◽  
Good Alternative ◽  
Condensation Heat Transfer ◽  
Air Cooling ◽  
Transfer Coefficients ◽  
Reduced Pressure ◽  
Evaporation Heat ◽  
Evaporation Heat Transfer ◽  
R 134A

When traditional air-to-air cooling is too voluminous, heat exchangers with long thermosyphons offer a good alternative. Experiments with a single thermosyphon with a large length-to-diameter ratio (188) and filled with R-134a are presented and analyzed. Saturation temperatures, filling ratios, and angles of inclination have been varied in wide ranges. A higher sensitivity of evaporation heat transfer coefficients on reduced pressure than in previous work has been found. Measurements revealed the effect of pressure or the saturation temperature on condensation heat transfer. The condensate film Reynolds number that marks a transition from one condensation heat transfer regime to another is found to depend on pressure. This effect was not accounted for by correlations from the literature. New correlations are presented to predict condensation and evaporation heat transfer rates.

Sign in / Sign up

Export Citation Format

Share Document