scholarly journals Evaluating Plastic Deformation and Damage as Potential Mechanisms for Tendon Inelasticity Using a Reactive Modeling Framework

2019 ◽  
Vol 141 (10) ◽  
Author(s):  
Babak N. Safa ◽  
Andrea H. Lee ◽  
Michael H. Santare ◽  
Dawn M. Elliott
Keyword(s):  
Plastic Deformation ◽  
Mechanical Response ◽  
Independent Set ◽  
Tensile Tests ◽  
The Other ◽  
Modeling Framework ◽  
Validation Data ◽  
Molecular Bond ◽  
Bond Kinetics ◽  
Comprehensive Framework

Inelastic behaviors, such as softening, a progressive decrease in modulus before failure, occur in tendon and are important aspects in degeneration and tendinopathy. These inelastic behaviors are generally attributed to two potential mechanisms: plastic deformation and damage. However, it is not clear which is primarily responsible. In this study, we evaluated these potential mechanisms of tendon inelasticity by using a recently developed reactive inelasticity model (RIE), which is a structurally inspired continuum mechanics framework that models tissue inelasticity based on the molecular bond kinetics. Using RIE, we formulated two material models, one specific to plastic deformation and the other to damage. The models were independently fit to published macroscale experimental tensile tests of rat tail tendons. We quantified the inelastic effects and compared the performance of the two models in fitting the mechanical response during loading, relaxation, unloading, and reloading phases. Additionally, we validated the models by using the resulting fit parameters to predict an independent set of experimental stress–strain curves from ramp-to-failure tests. Overall, the models were both successful in fitting the experiments and predicting the validation data. However, the results did not strongly favor one mechanism over the other. As a result, to distinguish between plastic deformation and damage, different experimental protocols will be needed. Nevertheless, these findings suggest the potential of RIE as a comprehensive framework for studying tendon inelastic behaviors.

scholarly journals Evaluating Plastic Deformation and Damage as Potential Mechanisms for Tendon Inelasticity using a Reactive Modeling Framework

2018 ◽  
Author(s):  
Babak N. Safa ◽  
Andrea H. Lee ◽  
Michael H. Santare ◽  
Dawn M. Elliott
Keyword(s):  
Plastic Deformation ◽  
Mechanical Response ◽  
Independent Set ◽  
The Other ◽  
Modeling Framework ◽  
Validation Data ◽  
Molecular Bond ◽  
Experimental Protocols ◽  
Bond Kinetics ◽  
Comprehensive Framework

ABSTRACTInelastic behaviors, such as softening, a progressive decrease in modulus before failure, occur in tendon andare important aspect in degeneration and tendinopathy. These in elastic behaviors are generally attributed to two potential mechanisms: plastic deformation and damage. However, it is not clear which is primarily responsible.In this study, we evaluated these potential mechanisms of tendon in elasticity by using a recently developed reactive in elasticity model (RIE), which is a structurally-inspired continuum mechanics frame work that models tissue in elasticity based on the molecular bond kinetics. Using RIE, we formulated two material models, one specific toplastic deformation and the other to damage. The models were independently fit to published experimental tensiletests of rat tail tendons. We quantified the inelastic effects and compared the performance of the two models infitting the mechanical response during loading, relaxation, unloading, and reloading phases. Additionally, we validated the models by using the resulting fit parameters to predict an independent set of experimental stress-straincurves from ramp-to-failure tests. Overall, the models were both successful in fitting the experiments and predicting the validation data. However, the results did not strongly favor one mechanism over the other. As a result, to distinguish between plastic deformation and damage, different experimental protocols will be needed. Nevertheless, these findings suggest the potential of RIE as a comprehensive framework for studying tendon inelastic behaviors.

Construction of plastic contact deformation maps on ceramics: a case study on aluminum nitride

1996 ◽  
Vol 54 ◽  
pp. 636-637
Author(s):  
D. L. Callahan
Keyword(s):  
Plastic Deformation ◽  
Aluminum Nitride ◽  
Mechanical Response ◽  
Three Dimensional ◽  
Bright Field Image ◽  
Perfectly Plastic ◽  
Contrast Analysis ◽  
Deformation Patterns

Modern polishing, precision machining and microindentation techniques allow the processing and mechanical characterization of ceramics at nanometric scales and within entirely plastic deformation regimes. The mechanical response of most ceramics to such highly constrained contact is not predictable from macroscopic properties and the microstructural deformation patterns have proven difficult to characterize by the application of any individual technique. In this study, TEM techniques of contrast analysis and CBED are combined with stereographic analysis to construct a three-dimensional microstructure deformation map of the surface of a perfectly plastic microindentation on macroscopically brittle aluminum nitride.The bright field image in Figure 1 shows a lg Vickers microindentation contained within a single AlN grain far from any boundaries. High densities of dislocations are evident, particularly near facet edges but are not individually resolvable. The prominent bend contours also indicate the severity of plastic deformation. Figure 2 is a selected area diffraction pattern covering the entire indentation area.

Electron microscope studies of the plastic deformation of ternary alloys based on GaAs

1990 ◽  
Vol 48 (4) ◽  
pp. 1120-1120
Author(s):  
R. Haswell ◽  
U. Bangert ◽  
P. Charsley
Keyword(s):  
Plastic Deformation ◽  
Electron Microscope ◽  
Room Temperature ◽  
Stacking Faults ◽  
The Other ◽  
Ternary Alloys ◽  
Dislocation Mobility ◽  
Semiconducting Materials ◽  
Micro Indentation

A knowledge of the behaviour of dislocations in semiconducting materials is essential to the understanding of devices which use them . This work is concerned with dislocations in alloys related to the semiconductor GaAs . Previous work on GaAs has shown that microtwinning occurs on one of the <110> rosette arms after indentation in preference to the other . We have shown that the effect of replacing some of the Ga atoms by Al results in microtwinning in both of the rosette arms.In the work to be reported dislocations in specimens of different compositions of Gax Al(1-x) As and Gax In(1-x) As have been studied by using micro indentation on a (001) face at room temperature . A range of electron microscope techniques have been used to investigate the type of dislocations and stacking faults/microtwins in the rosette arms , which are parallel to the [110] and [10] , as a function of composition for both alloys . Under certain conditions microtwinning occurs in both directions . This will be discussed in terms of the dislocation mobility.

scholarly journals Influence of Hydrostatic Extrusion on the Mechanical Properties of the Model Al-Mg Alloys

2021 ◽  
Author(s):  
Aleksandra Towarek ◽  
Wojciech Jurczak ◽  
Joanna Zdunek ◽  
Mariusz Kulczyk ◽  
Jarosław Mizera
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Tensile Strength ◽  
Microstructural Analysis ◽  
Tensile Tests ◽  
Hydrostatic Extrusion ◽  
Microstructure Formation ◽  
Initial State ◽  
Degree Of Deformation ◽  
Al Mg Alloys

AbstractTwo model aluminium-magnesium alloys, containing 3 and 7.5 wt.% of Mg, were subjected to plastic deformation by means of hydrostatic extrusion (HE). Two degrees of deformation were imposed by two subsequent reductions of the diameter. Microstructural analysis and tensile tests of the materials in the initial state and after deformation were performed. For both materials, HE extrusion resulted in the deformation of the microstructure—formation of the un-equilibrium grain boundaries and partition of the grains. What is more, HE resulted in a significant increase of tensile strength and decrease of the elongation, mostly after the first degree of deformation.

scholarly journals The Effect of Different Annealing Strategies on the Microstructure Development and Mechanical Response of Austempered Steels

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1041
Author(s):  
Eliseo Hernandez-Duran ◽  
Luca Corallo ◽  
Tanya Ros-Yanez ◽  
Felipe Castro-Cerda ◽  
Roumen H. Petrov
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Mechanical Response ◽  
Steel Grade ◽  
The Other ◽  
Microstructure Development ◽  
Microstructural Refinement ◽  
Heterogeneous Distribution ◽  
Parent Austenite ◽  
Conventional Annealing

This study focuses on the effect of non-conventional annealing strategies on the microstructure and related mechanical properties of austempered steels. Multistep thermo-cycling (TC) and ultrafast heating (UFH) annealing were carried out and compared with the outcome obtained from a conventionally annealed (CA) 0.3C-2Mn-1.5Si steel. After the annealing path, steel samples were fast cooled and isothermally treated at 400 °C employing the same parameters. It was found that TC and UFH strategies produce an equivalent level of microstructural refinement. Nevertheless, the obtained microstructure via TC has not led to an improvement in the mechanical properties in comparison with the CA steel. On the other hand, the steel grade produced via a combination of ultrafast heating annealing and austempering exhibits enhanced ductility without decreasing the strength level with respect to TC and CA, giving the best strength–ductility balance among the studied steels. The outstanding mechanical response exhibited by the UFH steel is related to the formation of heterogeneous distribution of ferrite, bainite and retained austenite in proportions 0.09–0.78–0.14. The microstructural formation after UFH is discussed in terms of chemical heterogeneities in the parent austenite.

Nitrendipine blocks high potassium contractures but not twitches in rat skeletal muscle

1988 ◽  
Vol 66 (9) ◽  
pp. 1210-1213 ◽  
Author(s):  
G. B. Frank ◽  
L. Konya ◽  
T. Subrahmanyam Sudha
Keyword(s):  
Skeletal Muscle ◽  
Calcium Ions ◽  
Calcium Uptake ◽  
Channel Blocker ◽  
Mechanical Response ◽  
Extracellular Calcium ◽  
The Other ◽  
Rat Skeletal Muscle ◽  
Potassium Depolarization ◽  
High Potassium

The effects of the organic calcium channel blocker nitrendipine was tested on electrically evoked twitches and on potassium depolarization-induced contractures of rat lumbricalis muscles. Nitrendipine (10−7 to 5 × 10−5 M) blocked only the potassium contractures. It was concluded that blocking calcium uptake through the slow voltage-senstitive calcium channels during potassium depolarization blocks the mechanical response of the muscle. Thus extracellular calcium ions are required for the excitation–contraction (E–C) coupling during depolarization contractures. On the other hand, electrically evoked twitches were not affected by nitrendipine; therefore, extracellular calcium ions entering via the slow voltage-sensitive channels are not required for E–C coupling during the twitch.

scholarly journals Mechanical Properties and Microstructural Aspects of Two High-Manganese Steels with TWIP/TRIP Effects: A Comparative Study

Metals ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 24
Author(s):  
Matías Bordone ◽  
Juan Perez-Ipiña ◽  
Raúl Bolmaro ◽  
Alfredo Artigas ◽  
Alberto Monsalve
Keyword(s):  
Mechanical Response ◽  
Volume Fraction ◽  
Tensile Tests ◽  
Optical Microscope ◽  
Chemical Compositions ◽  
High Manganese ◽  
Microstructural Changes ◽  
Ε Martensite ◽  
High Manganese Steels ◽  
Manganese Steels

This article is focused on the mechanical behavior and its relationship with the microstructural changes observed in two high-manganese steels presenting twinning-induced plasticity (TWIP) and transformation-induced plasticity (TRIP), namely Steel B and Steel C, respectively. Chemical compositions were similar in manganese, but carbon content of Steel B approximately doubles Steel C, which directly impacted on the stacking fault energy (SFE), microstructure and mechanical response of each alloy. Characterization of as-cast condition by optical microscope revealed a fully austenitic microstructure in Steel B and a mixed microstructure in Steel C consisting of austenite grains and thermal-induced (εt) martensite platelets. Same phases were observed after the thermo-mechanical treatment and tensile tests, corroborated by means of X-Ray Diffraction (XRD), which confirms no phase transformation in Steel B and TRIP effect in Steel C, due to the strain-induced γFCC→εHCP transformation that results in an increase in the ε-martensite volume fraction. Higher values of ultimate tensile strength, yield stress, ductility and impact toughness were obtained for Steel B. Significant microstructural changes were revealed in tensile specimens as a consequence of the operating hardening mechanisms. Scanning Electron Microscopy (SEM) observations on the tensile and impact test specimens showed differences in fracture micro-mechanisms.

Molecular Dynamics Modeling the Nano-Identation of Titanium

2021 ◽  
Author(s):  
Peiqiang Yang ◽  
Xueping Zhang ◽  
Zhenqiang Yao ◽  
Rajiv Shivpuri
Keyword(s):  
Molecular Dynamics ◽  
Plastic Deformation ◽  
Titanium Alloys ◽  
Large Scale ◽  
Mechanical Response ◽  
Pure Titanium ◽  
Dynamics Modeling ◽  
Dynamics Model ◽  
Nano Indentation ◽  
Molecular Dynamics Modeling

Abstract Titanium alloys’ excellent mechanical and physical properties make it the most popular material widely used in aerospace, medical, nuclear and other significant industries. The study of titanium alloys mainly focused on the macroscopic mechanical mechanism. However, very few researches addressed the nanostructure of titanium alloys and its mechanical response in Nano-machining due to the difficulty to perform and characterize nano-machining experiment. Compared with nano-machining, nano-indentation is easier to characterize the microscopic plasticity of titanium alloys. This research presents a nano-indentation molecular dynamics model in titanium to address its microstructure alteration, plastic deformation and other mechanical response at the atomistic scale. Based on the molecular dynamics model, a complete nano-indentation cycle, including the loading and unloading stages, is performed by applying Large-scale Atomic/Molecular Massively Parallel Simulator (LAMMPS). The plastic deformation mechanism of nano-indentation of titanium with a rigid diamond ball tip was studied under different indentation velocities. At the same time, the influence of different environment temperatures on the nano-plastic deformation of titanium is analyzed under the condition of constant indentation velocity. The simulation results show that the Young’s modulus of pure titanium calculated based on nano-indentation is about 110GPa, which is very close to the experimental results. The results also show that the mechanical behavior of titanium can be divided into three stages: elastic stage, yield stage and plastic stage during the nano-indentation process. In addition, indentation speed has influence on phase transitions and nucleation of dislocations in the range of 0.1–1.0 Å/ps.

scholarly journals Filling of Mater-Bi with Nanoclays to Enhance the Biofilm Rigidity

2018 ◽  
Vol 9 (4) ◽  
pp. 60 ◽  
Author(s):  
Giuseppe Cavallaro ◽  
Giuseppe Lazzara ◽  
Lorenzo Lisuzzo ◽  
Stefana Milioto ◽  
Filippo Parisi
Keyword(s):  
Tensile Properties ◽  
Food Packaging ◽  
Mechanical Response ◽  
Materials Science ◽  
Traction Force ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Nanocomposite Films ◽  
Preliminary Study ◽  
Mechanical Performances

We investigated the efficacy of several nanoclays (halloysite, sepiolite and laponite) as nanofillers for Mater-Bi, which is a commercial bioplastic extensively used within food packaging applications. The preparation of Mater-Bi/nanoclay nanocomposite films was easily achieved by means of the solvent casting method from dichloroethane. The prepared bio-nanocomposites were characterized by dynamic mechanical analysis (DMA) in order to explore the effect of the addition of the nanoclays on the mechanical behavior of the Mater-Bi-based films. Tensile tests found that filling Mater-Bi with halloysite induced the most significant improvement of the mechanical performances under traction force, while DMA measurements under the oscillatory regime showed that the polymer glass transition was not affected by the addition of the nanoclay. The tensile properties of the Mater-Bi/halloysite nanotube (HNT) films were competitive compared to those of traditional petroleum plastics in terms of the elastic modulus and stress at the breaking point. Both the mechanical response to the temperature and the tensile properties make the bio-nanocomposites appropriate for food packaging and smart coating purposes. Here, we report a preliminary study of the development of sustainable hybrid materials that could be employed in numerous industrial and technological applications within materials science and pharmaceutics.

Influence of Severe Plastic Deformation on the PLC Effect and Mechanical Properties in Al 5XXX Alloy

2006 ◽  
Vol 114 ◽  
pp. 171-176 ◽  
Author(s):  
Joanna Zdunek ◽  
Pawel Widlicki ◽  
Halina Garbacz ◽  
Jaroslaw Mizera ◽  
Krzysztof Jan Kurzydlowski
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Grain Size ◽  
Severe Plastic Deformation ◽  
True Strain ◽  
Tensile Tests ◽  
Size Reduction ◽  
Hydrostatic Extrusion ◽  
Stress Strain ◽  
Chatelier Effect

In this work, Al-Mg-Mn-Si alloy (5483) in the as-received and severe plastically deformed states was used. Plastic deformation was carried out by hydrostatic extrusion, and three different true strain values were applied 1.4, 2.8 and 3.8. All specimens were subjected to tensile tests and microhardness measurements. The investigated material revealed an instability during plastic deformation in the form of serration on the stress-strain curves, the so called Portevin-Le Chatelier effect It was shown that grain size reduction effected the character of the instability.

Sign in / Sign up

Export Citation Format

Share Document