Effect of Partition on the Mechanical Behaviors of Soft Adhesive Layers

2019 ◽  
Vol 86 (6) ◽  
Author(s):  
Danming Zhong ◽  
Junjie Liu ◽  
Yuhai Xiang ◽  
Tenghao Yin ◽  
Wei Hong ◽  
...  
Keyword(s):  
Cyclic Loading ◽  
Structural Design ◽  
Adhesive Layer ◽  
Mechanical Behaviors ◽  
Adhesive Layers ◽  
Mechanical Responses ◽  
Aspect Ratios ◽  
Instability Modes ◽  
Tensile Curve ◽  
Partition Process

A soft adhesive layer bonded between two rigid substrates, which are being pulled apart, may exhibit diverse instability phenomena before failure, such as cavitation, fingering, and fringe instability. In this study, by subdividing the soft layers into different numbers of disconnected smaller parts, we achieve desired instability modes and mechanical responses of the layer. The partition process not only retains the monotonicity on the tensile curve but also tunes the modulus and stretchability of the adhesive layer. Meanwhile, cavitation in layers of large aspect ratios is suppressed, and the hysteresis during cyclic loading is reduced. This study provides a guideline for the structural design of soft joints and adhesive layers.

scholarly journals Comparative Evaluation of Structural Systems for Tapered Tall Buildings

Buildings ◽  
2018 ◽  
Vol 8 (8) ◽  
pp. 108
Author(s):  
Kyoung Moon
Keyword(s):  
Structural Design ◽  
Comparative Evaluation ◽  
Building Materials ◽  
Tall Buildings ◽  
Structural Systems ◽  
Lateral Stiffness ◽  
Design Studies ◽  
Structural Efficiency ◽  
Aspect Ratios ◽  
Enormous Amount

Structural efficiency of tapered tall buildings has been well recognized, and many tall buildings of tapered forms have been built throughout the world. Tall buildings are built with an enormous amount of building materials. As one of the most efficient structural forms for tall buildings, the contribution of tapered forms to saving structural materials coming from our limited natural resources could be significant. Structural design of tall buildings is generally governed by lateral stiffness rather than strength. This paper systematically studies the structural efficiency of tapered tall buildings in terms of lateral stiffness. Tall buildings of various heights and angles of taper are designed with different structural systems prevalently used for today’s tall buildings, such as diagrids, braced tubes, and core-outrigger systems. The heights of the studied buildings range from 60 to 100 stories, and the corresponding height-to-width aspect ratios in their non-tapered prismatic forms range from 6.5 to 10.8. The angles of taper studied are 1, 2, and 3 degrees. Gross floor area of each building of the same story height is maintained to be the same regardless of the different angles of taper. Based on design studies, comparative evaluation of the various structural systems for tapered tall buildings is presented.

scholarly journals Hydroxypropylsulfonation/Caproylation of Cornstarch to Enhance Its Adhesion to PLA Fibers for PLA Sizing

Polymers ◽  
2019 ◽  
Vol 11 (7) ◽  
pp. 1197 ◽  
Author(s):  
Wei Li ◽  
Jie Wu ◽  
Xingui Cheng ◽  
Lanjuan Wu ◽  
Zhi Liu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Internal Stress ◽  
Mechanical Behaviors ◽  
Cohesive Failure ◽  
Adhesive Layers ◽  
Adhesion Measurement ◽  
Acid Sodium Salt ◽  
The Stability ◽  
The Impact ◽  
Scanning Electron

The impact of hydroxypropylsulfonation/caproylation on the adhesion of cornstarch to polylactic acid (PLA) fibers was investigated for ameliorating the applications such as PLA sizing. The hydroxypropylsulfonated and caproylated cornstarch (HCS) samples with different degrees of substitution (DS) were synthesized by a hydroxypropylsulfonation of acid-converted cornstarch (ACS) with 3-chloro-2-hydroxy-1-propanesulfonic acid sodium salt (CHPS-Na) and subsequently a caproylation with caproic anhydride (CA). The HCS granules were characterized by Fourier transform infrared spectroscopic and scanning electron microscopy. The adhesion was evaluated by measuring the bonding forces of the PLA roving impregnated. The mechanical behaviors of the adhesive layers were estimated by determining the properties of the films. The results of adhesion measurement were also analyzed especially through the wetting and spreading of the paste on the fiber surfaces, as well as the failure type, internal stress and mechanical behaviors of the adhesive layers among fibers. Additionally, apparent viscosity and its stability of the pastes were also determined. It was found that hydroxypropylsulfonation/caproylation was not only able to obviously improve the adhesion of ACS to PLA fibers, but also capable of further improving the adhesion of hydroxypropylsulfonated starch (HS) to the fibers. With the rise in the total DS, the adhesion gradually increased. The two substituents improved the wetting and spreading, reduced the internal stress, lowered the probabilities of interfacial failure and cohesive failure, decreased the film brittleness, and increased the van der Waals force at the interfaces. Moreover, the HCS samples with a stability of above 85% could meet the demand on the stability for sizing. Considering the experimental results of the adhesion and the analysis of the results, HCS showed potential in the application of PLA sizing.

scholarly journals Experimental Investigation of Adhesion Failure between Waterproof Coatings and Terrace Tiles under Usage Loads

Buildings ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 59
Author(s):  
Barbara Francke ◽  
Artur Piekarczuk
Keyword(s):  
Adhesive Layer ◽  
Ceramic Tiles ◽  
Applied Water ◽  
Water Contact ◽  
Adhesive Layers ◽  
Freeze Thaw ◽  
Adhesion Failure ◽  
Functional Factors ◽  
Tensile Adhesion ◽  
The Impact

This paper analyses the mechanism of the loss of functional properties of water-impermeable products used under ceramic tiles bonded with adhesives. Recorded damages were caused by selected ageing factors and were measured by the loss of adhesion of individual layers of the set. The analyzed phenomenon is found mainly on terraces and balconies located in a mid-European transitional climate, i.e., exposed to temperatures passing through 0 °C for three seasons a year. The tests reflected the action of three main functional factors, i.e., temperatures, water and freeze/thaw cycles. Tested waterproof coatings were grouped into three types, i.e., dispersion, cementitious and reaction resin-based products. Research kits consisted of liquid-applied water-impermeable products laid on a concrete substrate, adhesives and tiles. Comparing the effects of the action of the above-mentioned ageing factors revealed that water has the greatest impact on the reduction of the tensile adhesion strength of such sets. The adhesion of waterproof coatings to the concrete substrate showed higher values than the adhesion between the waterproof coating and the tile adhesive layers, regardless of the coating material. Both for samples not exposed to ageing factors, and for those exposed to such impacts, failure usually occurred in the adhesive layer or between the tile adhesive and the waterproof coating, without damaging the waterproof layer. The loss of adhesion of finishing layers to the substrate was not accompanied by a loss of tightness of the waterproof coating. The impact of negative water ageing was particularly destructive on the adhesion of cement-based tile adhesives to waterproof coatings made of polymer with a water dispersion of absorbability above 7% (V/V). There was no correlation among the results of adhesion of the finishing layers to the waterproofing layer after the action of the three ageing factors, i.e., water contact, elevated temperature and freeze/thaw cycles.

scholarly journals INELASTIC RESPONSES OF SWOLLEN NITRILE RUBBER UNDER CYCLIC LOADING

2018 ◽  
Vol 91 (1) ◽  
pp. 136-150 ◽  
Author(s):  
Mei Sze Loo ◽  
Jean Benoît Le Cam ◽  
Andri Andriyana ◽  
Eric Robin
Keyword(s):  
Cyclic Loading ◽  
Mechanical Response ◽  
Mechanical Responses ◽  
Material Compatibility ◽  
Durability Analysis ◽  
Inelastic Responses ◽  
Nitrile Rubbers ◽  
Loading Tests ◽  
Cyclic Loading Tests ◽  
Conventional Diesel Fuel

ABSTRACT Palm biodiesel is deemed a promising future fuel substitute for conventional diesel fuel. In line with this perspective, necessary changes in the existing diesel engine system are expected in order to address the issue of material compatibility. One typical degradation observed in rubber components exposed to aggressive solvent such as palm biodiesel during the service is swelling. Thus, the investigation of the effect of swelling on the mechanical response under cyclic loading is prerequisite for durability analysis of such components. In this study, filled and unfilled swollen nitrile rubbers are immersed in conventional diesel and palm biodiesel baths until a 5% swelling level is achieved. Both dry and swollen rubbers are subjected to uniaxial cyclic loading tests. The analysis of the mechanical responses has shown that swelling decreases inelastic effects such as hysteresis, stress softening, and permanent set. For both dry and swollen rubbers, fillers are found to have significant effects in the inelastic responses, whereas the effects of solvent and loading rate are comparable.

scholarly journals Quasi-Static Tests of Hybrid Adhesive Bonds Based on Biological Reinforcement in the Form of Eggshell Microparticles

Polymers ◽  
2020 ◽  
Vol 12 (6) ◽  
pp. 1391 ◽  
Author(s):  
Viktor Kolář ◽  
Miroslav Müller ◽  
Rajesh Mishra ◽  
Anna Rudawska ◽  
Vladimír Šleger ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cyclic Loading ◽  
Service Life ◽  
Adhesive Layer ◽  
Maximum Load ◽  
Adhesive Bonds ◽  
Static Tests ◽  
Static Test ◽  
The Matrix ◽  
Positive Effect

The paper is focused on the research of the cyclic loading of hybrid adhesive bonds based on eggshell microparticles in polymer composite. The aim of the research was to characterize the behavior of hybrid adhesive bonds with composite adhesive layer in quasi-static tests. An epoxy resin was used as the matrix and microparticles of eggshells were used as the filler. The adhesive bonds were exposed to cyclic loading and their service life and mechanical properties were evaluated. Testing was performed by 1000 cycles at 5–30% (165–989 N) and 5–70% (165–2307 N) of the maximum load of the filler-free bond in the static test. The results of the research show the importance of cyclic loading on the service life and mechanical properties of adhesive bonds. Quasi-static tests demonstrated significant differences between measured intervals of cyclic loading. All adhesive bonds resisted 1000 cycles of the quasi-static test with an interval loading 5–30%. The number of completed quasi-static tests with the interval loading 5–70% was significantly lower. The filler positively influenced the service life of adhesive bonds at a higher amount of quasi-static tests, i.e., the safety of adhesive bonds increased. The filler had a positive effect on adhesive bonds ABF2, where the strength significantly increased up to 20.26% at the loading of 5–30% against adhesive bonds ABF0. A viscoelasticity characteristic (creep) of the adhesive layer occurred at higher values of loading, i.e., between loading 5–70%. The viscoelasticity behavior did not occur at lower values of loading, i.e., between loading 5–30%.

Disc Mechanics With Trans-Endplate Partial Nucleotomy are not Fully Restored Following Cyclic Compressive Loading and Unloaded Recovery

2006 ◽  
Vol 128 (6) ◽  
pp. 823-829 ◽  
Author(s):  
Edward J. Vresilovic ◽  
Wade Johannessen ◽  
Dawn M. Elliott
Keyword(s):  
Cyclic Loading ◽  
Stress Relaxation ◽  
Nucleus Pulposus ◽  
Time Constant ◽  
Annulus Fibrosus ◽  
Compressive Loading ◽  
Magnetic Resonance Images ◽  
Mechanical Behaviors ◽  
Short Time

Mechanical function of the intervertebral disc is maintained through the interaction between the hydrated nucleus pulposus, the surrounding annulus fibrosus, and the superior and inferior endplates. In disc degeneration the normal transfer of load between disc substructures is compromised. The objective of this study was to explore the mechanical role of the nucleus pulposus in support of axial compressive loads over time. This was achieved by measuring the elastic slow ramp and viscoelastic stress-relaxation mechanical behaviors of cadaveric sheep motion segments before and after partial nucleotomy through the endplate (keeping the annulus fibrosus intact). Mechanics were evaluated at five conditions: Intact, intact after 10,000cycles of compression, acutely after nucleotomy, following nucleotomy and 10,000cycles of compression, and following unloaded recovery. Radiographs and magnetic resonance images were obtained to examine structure. Only the short time constant of the stress relaxation was altered due to nucleotomy. In contrast, cyclic loading resulted in significant and large changes to both the stiffness and stress relaxation behaviors. Moreover, the nucleotomy had little to no effect on the disc mechanics after cyclic loading, as there were no significant differences comparing mechanics after cyclic loading with or without the nucleotomy. Following unloaded recovery the mechanical changes that had occurred as a consequence of cyclic loading were restored, leaving only a sustained change in the short time constant due to the trans-endplate nucleotomy. Thus the swelling and redistribution of the remaining nucleus pulposus was not able to fully restore mechanical behaviors. This study reveals insights into the role of the nucleus pulposus in disc function, and provides new information toward the potential role of altered nucleus pulpous function in the degenerative cascade.

scholarly journals Interaction morphology and bond strength of nanofilled simplified-step adhesives to acid etched dentin

2012 ◽  
Vol 06 (04) ◽  
pp. 349-360 ◽  
Author(s):  
Vinicius Di Hipólito ◽  
André Figueiredo Reis ◽  
Sumita B Mitra ◽  
Mario Fernando de Goes
Keyword(s):  
Bond Strength ◽  
Colloidal Silica ◽  
Resin Composite ◽  
Adhesive Layer ◽  
Single Bond ◽  
Hybrid Layer ◽  
Microtensile Bond Strength ◽  
Tem Analysis ◽  
Cross Sectional ◽  
Adhesive Layers

ABSTRACTObjective: To evaluate the effect of nanofillers incorporated into adhesives on the microtensile bond strength (μ-TBS) and interfacial micromorphology to dentin.Methods: The occlusal enamel of 5 human molars was removed and each tooth sectioned into four quarters. The exposed dentin was treated with one of the following adhesives: Adper Single Bond (SB-unfilled), OptiBond Solo Plus (OS-barium aluminoborosilicate, 400nm Ø), Prime & Bond NT (NT-colloidal silica, 7-40 nm Ø) and Adper Single Bond 2 (SB2-colloidal silica, 5nm Ø). Cylinders of resin-based composite were constructed on the adhesive layers. After 24-hour storage, the restored tooth-quadrants were sectioned to obtain stick-shaped specimens (0.8 mm2, cross-sectional area) and submitted to μ-TBS at a cross-speed of 0.5 mm/min. Data were analyzed using one-way ANOVA and Tukey’s test (alpha = .05). Twenty-eight additional teeth were used for interfacial micromorphologic analysis by SEM (16-teeth) and TEM (12-teeth). The dentin surfaces of 32 discs were treated with the adhesives (8 discs for adhesive) and laminated to form disc-pairs using a flowable resin composite for SEM/EDS analysis. For TEM, 90nm-thick nondemineralized unstained sections were processed.Results: SB2 showed significant higher bond strength than SB, OS and NT. The SEM/EDS and TEM analysis revealed nanofillers infiltrated within the interfibrillar spaces of the SB2-hybrid layer. Fillers were concentrated around patent tubular orifices and in the adhesive layer for OS and NT.Conclusion: The presence of nanofillers within the interfibrillar spaces of the SB2-hybrid layer suggests its importance in the improvement of the μ-TBS. (Eur J Dent 2012;6:349-360)

scholarly journals A Model of Damage for Brittle and Ductile Adhesives in Glued Butt Joints

Technologies ◽  
2021 ◽  
Vol 9 (1) ◽  
pp. 19
Author(s):  
Maria Letizia Raffa ◽  
Raffaella Rizzoni ◽  
Frédéric Lebon
Keyword(s):  
Adhesive Layer ◽  
Imperfect Interface ◽  
Interface Condition ◽  
Stress Strain ◽  
Butt Joints ◽  
Adhesive Layers ◽  
Strain Behavior ◽  
Rate Dependent ◽  
Torsional Loads ◽  
Relative Errors

The paper presents a new analytical model for thin structural adhesives in glued tube-to-tube butt joints. The aim of this work is to provide an interface condition that allows for a suitable replacement of the adhesive layer in numerical simulations. The proposed model is a nonlinear and rate-dependent imperfect interface law that is able to accurately describe brittle and ductile stress–strain behaviors of adhesive layers under combined tensile–torsion loads. A first comparison with experimental data that were available in the literature provided promising results in terms of the reproducibility of the stress–strain behavior for pure tensile and torsional loads (the relative errors were less than 6%) and in terms of failure strains for combined tensile–torsion loads (the relative errors were less than 14%). Two main novelties are highlighted: (i) Unlike the classic spring-like interface models, this model accounts for both stress and displacement jumps, so it is suitable for soft and hard adhesive layers; (ii) unlike classic cohesive zone models, which are phenomenological, this model explicitly accounts for material and damage properties of the adhesive layer.

Sign in / Sign up

Export Citation Format

Share Document