Turbine Vane Endwall Film Cooling Comparison From Five Film-Hole Design Patterns and Three Upstream Injection Angles

2019 ◽  
Vol 11 (3) ◽  
Author(s):  
Chao-Cheng Shiau ◽  
Izzet Sahin ◽  
Nian Wang ◽  
Je-Chin Han ◽  
Hongzhou Xu ◽  
...  
Keyword(s):  
Film Cooling ◽  
Design Patterns ◽  
Density Ratio ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Injection Angle ◽  
Operation Conditions ◽  
Turbine Vane ◽  
End Wall ◽  
Endwall Cooling

Abstract The effects of upstream injection angle on film cooling effectiveness of a turbine vane end wall with various endwall film-hole designs were examined by applying pressure-sensitive paint (PSP) measurement technique. As the leakage flow from the slot between the combustor and the turbine vane is not considered an active source to protect the vane endwall in certain engine designs, discrete cylindrical holes are implemented near the slot to create an additional controllable upstream film to cool the vane end wall. Three potential injection angles were studied: 30 deg, 40 deg, and 50 deg. To explore the optimum endwall cooling design, five different film-hole patterns were tested: axial row, cross row, cluster, midchord row, and downstream row. Experiments were conducted in a four-passage linear cascade facility in a blowdown wind tunnel at the exit isentropic Mach number of 0.5 corresponding to inlet Reynolds number of 380,000 based on turbine vane axial chord length. A freestream turbulence intensity of 19% with an integral length scale of 1.7 cm was generated at the cascade inlet plane. Detailed film cooling effectiveness for each design was analyzed and compared at the design operation conditions (coolant mass flow ratio (MFR) 1% and density ratio 1.5). The results are presented in terms of high-fidelity film effectiveness contours and laterally (spanwise) averaged effectiveness. This paper will provide the gas turbine designers valuable information on how to select the best endwall cooling pattern with minimum cooling air consumption over a range of upstream injection angle.

Turbine Vane Endwall Film Cooling Comparison From Five Film-Hole Design Patterns and Three Upstream Leakage Injection Angles

2018 ◽  
Author(s):  
Chao-Cheng Shiau ◽  
Izzet Sahin ◽  
Nian Wang ◽  
Je-Chin Han ◽  
Hongzhou Xu ◽  
...  
Keyword(s):  
Film Cooling ◽  
Design Patterns ◽  
Density Ratio ◽  
Leakage Flow ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Injection Angle ◽  
Operation Conditions ◽  
Turbine Vane ◽  
Endwall Cooling

The effects of upstream leakage injection angle on film cooling effectiveness of a turbine vane endwall with various endwall film-hole designs were examined by applying PSP measurement technique. As the leakage flow from the slot between the combustor and the turbine vane is not considered an active source to protect the vane endwall in certain engine designs, discrete cylindrical holes are implemented near the slot to create additional controllable upstream leakage flow to cool the vane endwall. Three potential leakage injection angles were studied: 30°, 40°, and 50°. To explore the optimum endwall cooling design, five different film-hole patterns were tested: axial row, cross row, cluster, mid-chord row, and downstream row. Experiments were conducted in a four-passage linear cascade facility in a blowdown wind tunnel at the exit isentropic Mach number of 0.5 corresponding to inlet Reynolds number of 380,000 based on turbine vane axial chord length. A freestream turbulence intensity of 19% with an integral length scale of 1.7 cm was generated at the cascade inlet plane. Detailed film cooling effectiveness for each design was analyzed and compared at the design operation conditions (coolant mass flow ratio 1% and density ratio 1.5). The results are presented in terms of high-fidelity film effectiveness contours and laterally (spanwise) averaged effectiveness. This paper will provide the gas turbine designers valuable information on how to select the best endwall cooling pattern with minimum cooling air consumption over a range of upstream leakage injection angle.

Film Cooling Effectiveness Comparison on Turbine Vane Endwall With Cluster Configurations Using PSP Measurement Technique

2017 ◽  
Author(s):  
Nafiz H. K. Chowdhury ◽  
Chao-Cheng Shiau ◽  
Je-Chin Han ◽  
Hongzhou Xu ◽  
Michael Fox
Keyword(s):  
Measurement Technique ◽  
Film Cooling ◽  
Density Ratio ◽  
Blow Down ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Comparison Results ◽  
Turbine Vane ◽  
Cooling Hole ◽  
Endwall Cooling

Film cooling performance comparison on a turbine vane endwall with two different cluster configurations incorporating upstream inlet leakage flow was studied by applying PSP measurement technique. Experiments were conducted in a blow-down wind tunnel cascade facility at the exit isentropic Mach number of 0.5 corresponding to inlet Reynolds number of 380,000, based on axial chord length. A freestream turbulence level was generated as high as 19% with an integral length scale of 1.7 cm at the inlet of vanes’ leading edge plane. The results of each design and the comparison are presented in two-dimensional adiabatic film cooling effectiveness distributions on the endwall surface as well as the corresponding laterally averaged distributions. The focus of this study is to compare two different endwall cooling designs by the parametric effect of coolant-to-mainstream mass flow ratio (MFR) and density ratio (DR) on film cooling effectiveness. Initially, increased MFR for the endwall cooling and upstream leakage levels up the local film cooling effectiveness and yields improved coverage on the endwall. However, the endwall and upstream leakage demonstrate different behavior, while highest MFR does not provide any improvement as endwall cooling is suffered from the jet lift-off, highest MFR from the upstream leakage shows a monotonic increasing effectiveness on the endwall. On the other hand, the DR effect on effectiveness reveals different trend at a different design. Under a given amount of coolant supply and a fixed number of cooling hole, the comparison results really emphasize the importance of the cooling hole arrangement as one of the proposed cluster design can properly cover the whole endwall area.

Numerical Investigation of Effects of Blockage, Inclination Angle, and Hole-Size on Film Cooling Effectiveness at Concave Surface

2021 ◽  
Vol 143 (2) ◽  
Author(s):  
Fu-qiang Wang ◽  
Jian Pu ◽  
Jian-hua Wang ◽  
Wei-dong Xia
Keyword(s):  
Film Cooling ◽  
Pressure Loss ◽  
Numerical Study ◽  
Density Ratio ◽  
Concave Surface ◽  
Blockage Ratio ◽  
Coverage Area ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Injection Angle

Abstract Film-hole can be often blocked by thermal-barrier coatings (TBCs) spraying, resulting in the variations of aerodynamic and thermal performances of film cooling. In this study, a numerical study of the blockage effect on the film cooling effectiveness of inclined cylindrical-holes was carried out on a concave surface to simulate the airfoil pressure side. Three typical blowing ratios (BRs) of 0.5, 1.0, and 1.5 were chosen at an engine-similar density ratio (DR) of 2.0. Two common inclination angles of 30 deg and 45 deg were designed. The blockage ratios were adjusted from 0 to 20%. The results indicated the blockage could enhance the penetration of film cooling flow to the mainstream. Thus, the averaged effectiveness and coolant coverage area were reduced. Moreover, the pressure loss inside of the hole was increased. With the increase of BR, the decrement of film cooling effectiveness caused by blockage rapidly increased. At BR = 1.5, the decrement could be acquired up to 70% for a blockage ratio of 20%. The decrement of film cooling effectiveness caused by blockage was nearly nonsensitive to the injection angle; however, the larger angle could generate the higher increment of pressure loss caused by blockage. A new design method for the couple scheme of film cooling and TBC was proposed, i.e., increasing the inlet diameter according to the blockage ratio before TBC spraying. In comparison with the original unblocked-hole, the enlarged blocked-hole not only kept the nearly same area-averaged effectiveness but also reduced slightly the pressure loss inside of the hole. Unfortunately, application of enlarged blocked-hole at large BR could lead to a more obvious reduction of effectiveness near hole-exit, in comparison with the original common-hole.

Turbine Vane Endwall Film Cooling From Cross-Row Configuration With Simulated Upstream Leakage Flow

2017 ◽  
Author(s):  
Nafiz H. K. Chowdhury ◽  
Chao-Cheng Shiau ◽  
Je-Chin Han ◽  
Luzeng Zhang ◽  
Hee-Koo Moon
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Companion Paper ◽  
Leakage Flow ◽  
Blow Down ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Free Stream Turbulence ◽  
Lift Off ◽  
Endwall Cooling

The performance of a full coverage film cooling configuration called cross-row (CR) configuration including upstream inlet leakage flow was studied by measuring the adiabatic film cooling effectiveness distribution using PSP technique. Experiments were conducted in a blow-down wind tunnel cascade facility at the isentropic exit Mach number of 0.5 corresponding to inlet Reynolds number of 3.8 × 105, based on axial chord length. A free-stream turbulence level was generated as high as 19% with a length scale of 1.7 cm at the inlet. The results are presented as two-dimensional adiabatic film cooling effectiveness distributions on the endwall surface with corresponding spanwise averaged distributions. The focus of this study is to investigate the effect of coolant-to-mainstream mass flow ratio (MFR) and density ratio (DR) on the proposed endwall cooling design. Initially, increased MFR for the endwall cooling and upstream leakage levels up the local adiabatic cooling effectiveness and yields relatively uniform coverage on the entire endwall. However, in either case, highest MFR does not provide any improvement as endwall cooling suffered from the jet lift-off and leakage coolant coverage restricted by the downstream near-wall flow field. Results also indicated a density ratio of 1.5 provides the best performance. Finally, a fair comparison is made with another design called axial-row (AR) configuration from a companion paper.

Film Cooling Effectiveness of Transonic Turbine Vane Suction Side With Compound-Angle Shaped Hole Configuration

2015 ◽  
Author(s):  
Shang-Feng Yang ◽  
Je-Chin Han ◽  
Alexander MirzaMoghadam ◽  
Ardeshir Riahi
Keyword(s):  
Transonic Flow ◽  
Film Cooling ◽  
Surface Film ◽  
Density Ratio ◽  
Suction Side ◽  
Flow Loop ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Turbine Vane ◽  
Compound Angle

This paper studies the effect of transonic flow velocity on local film cooling effectiveness distribution of turbine vane suction side, experimentally. A conduction-free Pressure Sensitive Paint (PSP) method is used to determine the local film cooling effectiveness. Tests were performed in a five-vane annular cascade at Texas A&M Turbomachinery laboratory blow-down flow loop facility. The exit Mach numbers are controlled to be 0.7, 0.9, and 1.1, from subsonic to transonic flow conditions. Three foreign gases N2, CO2 and Argon/SF6 mixture are selected to study the effects of three coolant-to-mainstream density ratios, 1.0, 1.5, and 2.0 on film cooling. Four averaged coolant blowing ratios in the range, 0.7, 1.0, 1.3 and 1.6 are investigated. The test vane features 3 rows of radial-angle cylindrical holes around the leading edge, and 2 rows of compound-angle shaped holes on the suction side. Results suggest that the PSP technique is capable of producing clear and detailed film cooling effectiveness contours at transonic condition. The effects of coolant to mainstream blowing ratio, density ratio, and exit Mach number on the vane suction-surface film cooling distribution are obtained, and the consequence results are presented and explained in this investigation.

Turbine Vane Endwall Film Cooling Effectiveness of Different Purge Slot Configurations in a Linear Cascade

2019 ◽  
Author(s):  
Gunther Müller ◽  
Christian Landfester ◽  
Martin Böhle ◽  
Robert Krewinkel
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Region Of Interest ◽  
Experimental Tests ◽  
Secondary Flows ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Turbine Vane ◽  
Density Ratios ◽  
Endwall Film Cooling

Abstract This study is concerned with the film cooling effectiveness of the flow issuing from the gap between the NGV and the transition duct on the NGV endwall, i.e. the purge slot. Different slot widths, positions and injection angles were examined in order to represent changes due to thermal expansion as well as design modifications. Apart from these geometric variations, different blowing ratios (BR) and density ratios (DR) were realized to investigate the effects of the interaction between secondary flow and film cooling effectiveness. The experimental tests were performed in a linear scale-1 cascade equipped with four highly loaded turbine vanes at the Institute of Fluid Mechanics and Fluid Machinery of the University of Kaiserslautern. The mainstream flow parameters were, with a Reynolds number of 300,000 and a Mach number (outlet) of 0.6, set to meet real engine conditions. By using various flow conditioners, periodic flow was obtained in the region of interest (ROI). The adiabatic film cooling effectiveness was determined by using the Pressure Sensitive Paint (PSP) technique. In this context, nitrogen and carbon dioxide were used as tracer gases realizing two different density ratios DR = 1.0 and 1.6. The investigation was conducted for a broad range of blowing ratios with 0.25 ≤ BR ≤ 1.50. In combination with 10 geometry variations and the aforementioned blowing and density ratio variations 100 single operating points were investigated. For a better understanding of the coolant distribution, the secondary flows on the endwall were visualized by oil dye. The measurement results will be discussed based on the areal distribution of film cooling effectiveness, its lateral spanwise as well as its area average. The results will provide a better insight into various parametric effects of gap variations on turbine vane endwall film cooling performance — notably under realistic engine conditions.

Full-Scale Turbine Vane End-Wall Film-Cooling Effectiveness Distribution Using PSP Technique

2015 ◽  
Author(s):  
Chao-Cheng Shiau ◽  
Andrew F. Chen ◽  
Je-Chin Han ◽  
Salam Azad ◽  
Ching-Pang Lee
Keyword(s):  
Film Cooling ◽  
Full Scale ◽  
Complex Flow ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Free Stream Turbulence ◽  
Turbine Vane ◽  
Tunnel Design ◽  
End Wall

Researchers in gas turbine field take great interest in the cooling performance on the first-stage vane because the complex flow characteristics and intensive heat load that comes from the exit of the combustion chamber. A better understanding is needed on how the coolant flow interacts with the mainstream and the resulting cooling effect in the real engine especially for the first-stage vane. An authentic flow channel and condition should be achieved. In this study, three full-scale turbine vanes are used to construct an annular-sector cascade. The film-cooling design is attained through numerous layback fan-shaped and cylindrical holes dispersed on the vane and both end-walls. With the three-dimensional vane geometry and corresponding wind tunnel design, the true flow field can thus be simulated as in the engine. This study targets the film-cooling effectiveness on the inner end-wall (hub) of turbine vane. Tests are performed under the mainstream Reynolds number 3.5 × 105; the related inlet Mach number is 0.09 and the free stream turbulence intensity is 8%. Two variables, coolant-to-mainstream mass flow ratios (MFR = 2%, 3%, 4%) and density ratios (DR = 1.0, 1.5) are examined. Pressure-sensitive paint (PSP) technique is utilized to capture the detail contour of film-cooling effectiveness on the inner end-wall and demonstrate the coolant trace. The presented results serve a comparison basis for other sets of vanes with different cooling designs. The results are expected to strengthen the promise of PSP technique on evaluating the film-cooling performance of the engine geometries.

High Resolution Film Cooling Effectiveness Comparison of Axial and Compound Angle Holes on the Suction Side of a Turbine Vane

2006 ◽  
Author(s):  
Scot K. Waye ◽  
David G. Bogard
Keyword(s):  
High Resolution ◽  
Flat Plate ◽  
Film Cooling ◽  
Density Ratio ◽  
Suction Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Turbine Vane ◽  
Adiabatic Effectiveness ◽  
Compound Angle

Film cooling adiabatic effectiveness for axial and compound angle holes on the suction side of a simulated turbine vane was investigated to determine the relative performance of these configurations. The effect of the surface curvature was also evaluated by comparing to previous curvature studies and flat plate film cooling results. Experiments were conducted for varying coolant density ratio, mainstream turbulence levels, and hole spacing. Results from these measurements showed that for mild curvature, 2r/d ≈ 160, flat plate results are sufficient to predict the cooling effectiveness. Furthermore, the compound angle injection improves adiabatic effectiveness for higher blowing ratios, similar to previous studies using flat plate facilities.

Turbine Vane Endwall Film Cooling With Slashface Leakage and Discrete Hole Configuration

2017 ◽  
Vol 139 (6) ◽  
Author(s):  
Nafiz H. K. Chowdhury ◽  
Chao-Cheng Shiau ◽  
Je-Chin Han ◽  
Luzeng Zhang ◽  
Hee-Koo Moon
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Density Ratio ◽  
Secondary Flows ◽  
Blow Down ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Free Stream Turbulence ◽  
Leakage Flows ◽  
Turbine Vane

Turbine vanes are typically assembled as a section containing single or double airfoil units in an annular pattern. First stage guide vane assembly results in two common mating interfaces: a gap between combustor and vane endwall and another resulted from the adjacent sections, called slashface. High pressure coolant could leak through these gaps to reduce the ingestion of hot gas and achieve certain cooling benefit. As vane endwall region flow field is already very complicated due to highly three-dimensional secondary flows, then a significant influence on endwall cooling can be expected due to the gap leakage flows. To determine the effect of leakage flows from those gaps, film cooling effectiveness distributions were measured using pressure sensitive paint (PSP) technique on the endwall of a scaled up, midrange industrial turbine vane geometry with the multiple rows of discrete film cooling (DFC) holes inside the passages. Experiments were performed in a blow-down wind tunnel cascade facility at the exit Mach number of 0.5 corresponding to Reynolds number of 3.8 × 105 based on inlet conditions and axial chord length. Passive turbulence grid was used to generate free-stream turbulence (FST) level about 19% with an integral length scale of 1.7 cm. Two parameters, coolant-to-mainstream mass flow ratio (MFR) and density ratio (DR), were studied. The results are presented as two-dimensional film cooling effectiveness distribution on the vane endwall surface with the corresponding spanwise averaged values along the axial direction.

Transonic Turbine Vane Endwall Film Cooling Using PSP Measurement Technique

2019 ◽  
Author(s):  
Chao-Cheng Shiau ◽  
Izzet Sahin ◽  
Izhar Ullah ◽  
Je-Chin Han ◽  
Alexander V. Mirzamoghadam ◽  
...  
Keyword(s):  
Shock Wave ◽  
Film Cooling ◽  
Density Ratio ◽  
Cross Flow ◽  
Flow Conditions ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Flow ◽  
Turbine Vane ◽  
Endwall Film Cooling

Abstract This work focuses on the parametric study of film cooling effectiveness on turbine vane endwall under various flow conditions. The experiments were performed in a five-vane annular sector cascade facility in a blowdown wind tunnel. The controlled exit isentropic Mach numbers were 0.7, 0.9, and 1.0, from high subsonic to transonic conditions. The freestream turbulence intensity is estimated to be 12%. Three coolant-to-mainstream mass flow ratios (MFR) in the range 0.75%, 1.0%, and 1.25% are studied. N2, CO2, and Argon/SF6 mixture were used to investigate the effects of density ratio (DR), ranging from 1.0, 1.5 to 2.0. There are 8 cylindrical holes on the endwall inside the passage. Pressure-sensitive paint (PSP) technique was used to capture the endwall pressure distribution for shock wave visualization and obtain the detailed film cooling effectiveness distributions. Both the high-fidelity effectiveness contour and the laterally (spanwise) averaged effectiveness were measured to quantify the parametric effect. This study will provide the gas turbine designer more insight on how the endwall film cooling effectiveness varies with different cooling flow conditions including shock wave through the endwall cross-flow passage.

Sign in / Sign up

Export Citation Format

Share Document