Numerical Investigation on Film Cooling Performance of Fusiform Diffusion Holes

2018 ◽  
Vol 140 (12) ◽  
Author(s):  
Bai-Tao An ◽  
Jian-Jun Liu
Keyword(s):  
Numerical Investigation ◽  
Cross Section ◽  
Film Cooling ◽  
Discharge Coefficient ◽  
Cross Sectional ◽  
Cooling Performance ◽  
Blowing Ratio ◽  
Section Area ◽  
Two Sides ◽  
Dynamics Method

This paper presents a numerical investigation of the film-cooling performance of a kind of diffusion hole with a fusiform cross section. Relative to the rectangular diffusion hole, the up- and/or downstream wall of the fusiform diffusion hole is outer convex. Under the same metering section area, six fusiform diffusion holes were divided into two groups with cross-sectional widths of W = 1.7D and W = 2.0D, respectively. Three fusiform cross section shapes in each group included only downstream wall outer convex, only upstream wall outer convex, or a combination of both. Simulations were performed in a flat plate model using a 3D steady computational fluid dynamics method under an engine-representative condition. The simulation results showed that the fusiform diffusion hole with only an outer convex upstream wall migrates the coolant laterally toward the hole centerline, and then forms or enhances a tripeak effectiveness pattern. Conversely, the fusiform diffusion hole with an outer convex downstream wall intensely expands the coolant to the hole two sides, and results in a bipeak effectiveness pattern, regardless of the upstream wall shape. Compared with the rectangular diffusion holes, the fusiform diffusion holes with only an upstream wall outer convex significantly increase the overall effectiveness at high blowing ratios. The increased magnitude is approximately 20% for the hole of W = 1.7D at M = 2.5. Besides, the fusiform diffusion holes with an outer convex upstream wall increase the discharge coefficient about 5%, within the moderate to high blowing ratio range.

Quantifying Blowing Ratio for Shaped Cooling Holes

2017 ◽  
Author(s):  
D. J. Cerantola ◽  
A. M. Birk
Keyword(s):  
Film Cooling ◽  
Discharge Coefficient ◽  
Area Ratio ◽  
Operating Conditions ◽  
Gas Turbine Combustor ◽  
Adiabatic Wall ◽  
Cross Sectional ◽  
Cooling Performance ◽  
Blowing Ratio ◽  
Cooling Hole

Effusion cooling was a popular technology integrated into the design of gas turbine combustor liners. A staggering amount of research was completed that quantified performance with respect to operating conditions and cooling hole geometric properties; however, most of these investigations did not address the influence of the manufacturing process on the hole shape. This study completed an adiabatic wall numerical analysis using the realizable k-ε turbulence model of a laser-drilled hole that had a nozzled profile with an area ratio of 0.24 and five additional cylindrical, nozzled, diffusing, and filleted holes that yielded the same hole mass flow rate at representative engine conditions. The traditional methods for quantifying blowing ratio yielded the same value for all holes that was not useful considering the substantial differences in film cooling performance. It was proposed to define hole mass flux based on the outlet y-cross sectional area projected onto the inclination angle plane. This gave blowing ratios that correlated to better and worse cooling performance for the diffusing and nozzled holes respectively. The diffusing hole delivered the best film cooling due to having the lowest effluent velocity and greatest amount of in-hole turbulent production, which coincided with the worst discharge coefficient.

Quantifying Blowing Ratio for Shaped Cooling Holes

2017 ◽  
Vol 140 (2) ◽  
Author(s):  
D. J. Cerantola ◽  
A. M. Birk
Keyword(s):  
Film Cooling ◽  
Discharge Coefficient ◽  
Area Ratio ◽  
Operating Conditions ◽  
Gas Turbine Combustor ◽  
Adiabatic Wall ◽  
Cross Sectional ◽  
Cooling Performance ◽  
Blowing Ratio ◽  
Cooling Hole

Effusion cooling has been a popular technology integrated into the design of gas turbine combustor liners. A staggering amount of research was completed that quantified performance with respect to operating conditions and cooling hole geometric properties; however, most of these investigations did not address the influence of the manufacturing process on the hole shape. This study completed an adiabatic wall numerical analysis using the realizable k–ϵ turbulence model of a laser-drilled hole that had a nozzled profile with an area ratio of 0.24 and five additional cylindrical, nozzled, diffusing, and fileted holes that yielded the same hole mass flow rate at representative engine conditions. The traditional methods for quantifying blowing ratio yielded the same value for all holes that was not useful considering the substantial differences in film cooling performance. It was proposed to define hole mass flux based on the outlet y-cross-sectional area projected onto the inclination angle plane. This gave blowing ratios that correlated to better and worse cooling performance for the diffusing and nozzled holes, respectively. The diffusing hole delivered the best film cooling due to having the lowest effluent velocity and greatest amount of in-hole turbulent production, which coincided with the worst discharge coefficient.

Investigations on the Influence of Rib Orientation Angle on Film Cooling Performance of Compound Holes

2018 ◽  
Author(s):  
Lin Ye ◽  
Cun-liang Liu ◽  
Hai-yong Liu ◽  
Hui-ren Zhu ◽  
Jian-xia Luo
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Discharge Coefficient ◽  
Orientation Angle ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio

To investigate the effects of the inclined ribs on internal flow structure in film hole and the film cooling performance on outer surface, experimental and numerical studies are conducted on the effects of rib orientation angle on film cooling of compound cylindrical holes. Three coolant channel cases, including two ribbed cross-flow channels (135° and 45° angled ribs) and the plenum case, are studied under three blowing ratios (0.5, 1.0 and 2.0). 2D contours of film cooling effectiveness as well as heat transfer coefficient were measured by transient liquid crystal measurement technique (TLC). The steady RANS simulations with realizable k-ε turbulence model and enhanced wall treatment were performed. The results show that the spanwise width of film coverage is greatly influenced by the rib orientation angle. The spanwise width of the 45° rib case is obviously larger than that of the 135° rib case under lower blowing ratios. When the blowing ratio is 1.0, the area-averaged cooling effectiveness of the 135° rib case and the 45° rib case are higher than that of the plenum case by 38% and 107%, respectively. With the increase of blowing ratio, the film coverage difference between different rib orientation cases becomes smaller. The 45° rib case also produces higher heat transfer coefficient, which is higher than the 135° rib case by 3.4–8.7% within the studied blowing ratio range. Furthermore, the discharge coefficient of the 45° rib case is the lowest among the three cases. The helical motion of coolant flow is observed in the hole of 45° rib case. The jet divides into two parts after being blown out of the hole due to this motion, which induces strong velocity separation and loss. For the 135° rib case, the vortex in the upper half region of the secondary-flow channel rotates in the same direction with the hole inclination direction, which leads to the straight streamlines and thus results in lower loss and higher discharge coefficient.

Experimental and Numerical Investigation on Film Cooling Performance and Flow Structure of Film Holes

2019 ◽  
Author(s):  
Nan Cao ◽  
Xue Li ◽  
Ze-yu Wu ◽  
Xiang Luo
Keyword(s):  
Flow Visualization ◽  
Numerical Investigation ◽  
Flow Structure ◽  
Film Cooling ◽  
Cylindrical Hole ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Blowing Ratio ◽  
Visualization Experiment ◽  
Shaped Hole

Abstract Discrete hole film cooling has been commonly used as an effective cooling technique to protect gas turbine blades from hot gas. There have been numerous investigations on the cylindrical hole and shaped hole, but few experimental investigations on the cooling mechanism of the novel film holes with side holes (anti-vortex hole and sister hole) are available. This paper presents an experimental and numerical investigation to study the film cooling performance and flow structure of four kinds of film holes (cylindrical hole, fan-shaped hole, anti-vortex hole and sister hole) on the flat plate. The film holes have the same main hole diameter of 4mm and the same inclination angle of 45°. The adiabatic film cooling effectiveness is obtained by the steady-state Thermochromic Liquid Crystal (TLC). The flow visualization experiment and numerical investigation are performed to investigate the flow structure and counter-rotating vortex pair (CRVP) intensity. The smoke is selected as the tracer particle in the flow visualization experiment. The mainstream Reynolds number is 2900, the blowing ratio ranges from 0.3 to 2.0, and the density ratio of coolant to mainstream is 1.065. Experimental results show that compared with the cylindrical hole, the film cooling performance of the anti-vortex hole and sister hole shows significant improvement at all blowing ratios. The sister hole can achieve the best cooling performance at blowing ratios of 0.3 to 1.5. The fan-shaped hole only performs well at high blowing ratios and it performs best at the blowing ratio of 2.0. Flow visualization experiment and numerical investigation reveal that the anti-vortex hole and sister hole can decrease the CRVP intensity of the main hole and suppress the coolant lift-off because of side holes, which increases the film coverage and cooling effectiveness. For the sister hole, the side holes are parallel to the main hole, but for the anti-vortex hole, there are lateral angles between them. The coolant interaction between the side holes and main hole of the sister hole is stronger than that of the anti-vortex hole. Therefore, the sister hole provides better film cooling performance than the anti-vortex hole.

Film Cooling Investigation of a Slot-Based Diffusion Hole

2016 ◽  
Author(s):  
Bai-Tao An ◽  
Jian-Jun Liu ◽  
Si-Jing Zhou ◽  
Xiao-Dong Zhang ◽  
Chao Zhang
Keyword(s):  
Cross Section ◽  
Film Cooling ◽  
Rectangular Cross Section ◽  
Density Ratio ◽  
Vortex Structures ◽  
Cross Sectional ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Shaped Hole

This paper presents a new configuration of discrete film hole, i.e., the slot-based diffusion hole. Retaining the similar diffusion features to a traditional diffusion hole, the slot-based diffusion hole transforms the cross section of circle for the traditional diffusion hole to a flattened rectangle with respect to the equivalent cross-sectional area. Consequently, the exit width of the new hole is effectively enlarged. To verify the film cooling effectiveness, a low speed flat plate experimental facility incorporated with Pressure Sensitive Paint (PSP) measurement technique was employed to obtain the adiabatic film cooling effectiveness. The experiments were performed with hole pitch to diameter ratio p/D=6 and density ratio DR=1.38. The blowing ratio was varied from M=0.5 to M=2.5. A fan-shaped hole and two slot-based diffusion holes were tested and compared. Three-dimensional numerical simulation was employed to analyze the flow field in detail. The experimental results showed that the area averaged effectiveness of two slot-based diffusion holes is significantly higher than that of the fan-shaped hole when the blowing ratio exceeds 1.0. The slot-based diffusion hole demonstrates the great advantage over the fan-shaped hole at hole exit and maintains this to far downstream. The numerical results showed that the ends shape of the flattened rectangular cross section has large influences on film distribution patterns and downstream vortex structures. The semi-circle and straight line ends shapes lead to a bi-peak and a single-peak effectiveness pattern, respectively. The optimal ends shape can regulate the vortex structures and improve the film cooling effectiveness further.

Investigations on the Influence of Rib Orientation Angle on Film Cooling Performance of Cylindrical Holes

2017 ◽  
Author(s):  
Lin Ye ◽  
Cun-liang Liu ◽  
Hui-ren Zhu ◽  
Jian-xia Luo ◽  
Ying-ni Zhai
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Discharge Coefficient ◽  
Cross Flow ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Flow Channels ◽  
Cylindrical Holes

This paper presents an experimental and numerical investigation on the film cooling with different coolant feeding channel structures. Two ribbed cross-flow channels with rib-orientation of 135° and 45° respectively and the plenum coolant channel have been studied and compared to find out the effect of rib orientation on the film cooling performances of cylindrical holes. The film cooling effectiveness and heat transfer coefficient were measured by the transient heat transfer measurement technique with narrow-band thermochromic liquid crystal. Numerical simulations with realizable k-ε turbulence model were also performed to analyze the flow mechanism. The results show that the coolant channel structure has a notable effect on the flow structure of film jet which is the most significant mechanism affecting the film cooling performance. Generally, film cooling cases fed with ribbed cross-flow channels have asymmetric counter-rotating vortex structures and related asymmetric temperature distributions, which make the film cooling effectiveness and the heat transfer coefficient distributions asymmetric to the hole centerline. The discharge coefficient of the 45° rib case is the lowest among the three cases under all the blowing ratios. And the plenum case has higher discharge coefficient than the 135° rib case under low blowing ratio. With the increase of blowing ratio, the discharge coefficient of the 135° rib case gets larger than the plenum case gradually, because the vortex in the upper half region of the coolant channel rotates in the same direction with the film hole inclination direction and makes the jet easy to flow into the film hole in the 135° rib case.

Numerical Investigation on the Effects of Vortex Generator Locations on Film Cooling Performance

2019 ◽  
Vol 0 (0) ◽  
Author(s):  
Daren Zheng ◽  
Xinjun Wang ◽  
Qi Yuan
Keyword(s):  
Adverse Effect ◽  
Numerical Investigation ◽  
Opposite Direction ◽  
Film Cooling ◽  
Vortex Generator ◽  
Cooling Performance ◽  
Blowing Ratio ◽  
Twisted Flow

Abstract Described in this paper is a numerical investigation on the concept for enhancing film cooling performance by placing vortex generator (VG) upstream the film hole. Six film cooling configurations with different VG locations are investigated, including the distances for VG upstream the film hole (Upstream Distances) of 20 mm, 25 mm, and 30 mm and the VG gaps of 0, 2 mm, 4 mm and 6 mm respectively. The effect of VG locations on film cooling performance were conducted. The film cooling performance is evaluated at the density of 0.97 with the blowing ratio of 1.0. Results obtained show that the twisted flow generated by upstream VG rotates in the opposite direction of kidney vortex, producing an adverse effect on kidney vortex. The enhanced adverse effect could dramatically improve the film cooling performance. Moreover, the intensity of twisted flow is greatly related to the VG locations. The film cooling performance improves with the increasing upstream distances. The film cooling performance improves first and then impairs with increasing VG gaps. In this case, the film cooling performance in the case with gap of 4 mm is superior to those in other cases.

Film Cooling From Novel Sister Shaped Single-Holes

2014 ◽  
Author(s):  
Siavash Khajehhasani ◽  
Bassam Jubran
Keyword(s):  
Film Cooling ◽  
Three Dimensional ◽  
Lateral Spreading ◽  
Navier Stokes ◽  
The Novel ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Shaped Hole ◽  
Lift Off

A numerical investigation of the film cooling performance from novel sister shaped single-holes (SSSH) is presented in this paper and the obtained results are compared with a single cylindrical hole, a forward diffused shaped hole, as well as discrete sister holes. Three types of the novel sister shaped single-hole schemes namely downstream, upstream and up/downstream SSSH, are designed based on merging the discrete sister holes to the primary hole in order to reduce the jet lift-off effect and increase the lateral spreading of the coolant on the blade surface as well as a reduction in the amount of coolant in comparison with discrete sister holes. The simulations are performed using three-dimensional Reynolds-Averaged Navier Stokes analysis with the realizable k–ε model combined with the standard wall function. The upstream SSSH demonstrates similar film cooling performance to that of the forward diffused shaped hole for the low blowing ratio of 0.5. While it performs more efficiently at M = 1, where the centerline and laterally averaged effectiveness results improved by 70% and 17%, respectively. On the other hand, the downstream and up/downstream SSSH schemes show a considerable improvement in film cooling performance in terms of obtaining higher film cooling effectiveness and less jet lift-off effect as compared with the single cylindrical and forward diffused shaped holes for both blowing ratios of M = 0.5 and 1. For example, the laterally averaged effectiveness for the downstream SSSH configuration shows an improvement of approximately 57% and 110% on average as compared to the forward diffused shaped hole for blowing ratios of 0.5 and 1, respectively.

Experimental Study of the Effects of an Oscillating Approach Flow on Overall Cooling Performance of a Simulated Turbine Blade Leading Edge

2009 ◽  
Author(s):  
Ross Johnson ◽  
Jonathan Maikell ◽  
David Bogard ◽  
Justin Piggush ◽  
Atul Kohli ◽  
...  
Keyword(s):  
Turbine Blade ◽  
Film Cooling ◽  
Density Ratio ◽  
Leading Edge ◽  
Stagnation Line ◽  
Cooling Performance ◽  
Blowing Ratio ◽  
Oscillation Frequencies ◽  
Overall Effectiveness ◽  
Blade Leading Edge

When a turbine blade passes through wakes from upstream vanes it is subjected to an oscillation of the direction of the approach flow resulting in the oscillation of the position of the stagnation line on the leading edge of the blade. In this study an experimental facility was developed that induced a similar oscillation of the stagnation line position on a simulated turbine blade leading edge. The overall effectiveness was evaluated at various blowing ratios and stagnation line oscillation frequencies. The location of the stagnation line on the leading edge was oscillated to simulate a change in angle of attack between α = ± 5° at a range of frequencies from 2 to 20 Hz. These frequencies were chosen based on matching a range of Strouhal numbers typically seen in an engine due to oscillations caused by passing wakes. The blowing ratio was varied between M = 1, M = 2, and M = 3. These experiments were carried out at a density ratio of DR = 1.5 and mainstream turbulence levels of Tu ≈ 6%. The leading edge model was made of high conductivity epoxy in order to match the Biot number of an actual engine airfoil. Results of these tests showed that the film cooling performance with an oscillating stagnation line was degraded by as much as 25% compared to the performance of a steady flow with the stagnation line aligned with the row of holes at the leading edge.

Sign in / Sign up

Export Citation Format

Share Document