Quantifying Blowing Ratio for Shaped Cooling Holes

2017 ◽  
Vol 140 (2) ◽  
Author(s):  
D. J. Cerantola ◽  
A. M. Birk
Keyword(s):  
Film Cooling ◽  
Discharge Coefficient ◽  
Area Ratio ◽  
Operating Conditions ◽  
Gas Turbine Combustor ◽  
Adiabatic Wall ◽  
Cross Sectional ◽  
Cooling Performance ◽  
Blowing Ratio ◽  
Cooling Hole

Effusion cooling has been a popular technology integrated into the design of gas turbine combustor liners. A staggering amount of research was completed that quantified performance with respect to operating conditions and cooling hole geometric properties; however, most of these investigations did not address the influence of the manufacturing process on the hole shape. This study completed an adiabatic wall numerical analysis using the realizable k–ϵ turbulence model of a laser-drilled hole that had a nozzled profile with an area ratio of 0.24 and five additional cylindrical, nozzled, diffusing, and fileted holes that yielded the same hole mass flow rate at representative engine conditions. The traditional methods for quantifying blowing ratio yielded the same value for all holes that was not useful considering the substantial differences in film cooling performance. It was proposed to define hole mass flux based on the outlet y-cross-sectional area projected onto the inclination angle plane. This gave blowing ratios that correlated to better and worse cooling performance for the diffusing and nozzled holes, respectively. The diffusing hole delivered the best film cooling due to having the lowest effluent velocity and greatest amount of in-hole turbulent production, which coincided with the worst discharge coefficient.

Quantifying Blowing Ratio for Shaped Cooling Holes

2017 ◽  
Author(s):  
D. J. Cerantola ◽  
A. M. Birk
Keyword(s):  
Film Cooling ◽  
Discharge Coefficient ◽  
Area Ratio ◽  
Operating Conditions ◽  
Gas Turbine Combustor ◽  
Adiabatic Wall ◽  
Cross Sectional ◽  
Cooling Performance ◽  
Blowing Ratio ◽  
Cooling Hole

Effusion cooling was a popular technology integrated into the design of gas turbine combustor liners. A staggering amount of research was completed that quantified performance with respect to operating conditions and cooling hole geometric properties; however, most of these investigations did not address the influence of the manufacturing process on the hole shape. This study completed an adiabatic wall numerical analysis using the realizable k-ε turbulence model of a laser-drilled hole that had a nozzled profile with an area ratio of 0.24 and five additional cylindrical, nozzled, diffusing, and filleted holes that yielded the same hole mass flow rate at representative engine conditions. The traditional methods for quantifying blowing ratio yielded the same value for all holes that was not useful considering the substantial differences in film cooling performance. It was proposed to define hole mass flux based on the outlet y-cross sectional area projected onto the inclination angle plane. This gave blowing ratios that correlated to better and worse cooling performance for the diffusing and nozzled holes respectively. The diffusing hole delivered the best film cooling due to having the lowest effluent velocity and greatest amount of in-hole turbulent production, which coincided with the worst discharge coefficient.

Numerical Investigation on Film Cooling Performance of Fusiform Diffusion Holes

2018 ◽  
Vol 140 (12) ◽  
Author(s):  
Bai-Tao An ◽  
Jian-Jun Liu
Keyword(s):  
Numerical Investigation ◽  
Cross Section ◽  
Film Cooling ◽  
Discharge Coefficient ◽  
Cross Sectional ◽  
Cooling Performance ◽  
Blowing Ratio ◽  
Section Area ◽  
Two Sides ◽  
Dynamics Method

This paper presents a numerical investigation of the film-cooling performance of a kind of diffusion hole with a fusiform cross section. Relative to the rectangular diffusion hole, the up- and/or downstream wall of the fusiform diffusion hole is outer convex. Under the same metering section area, six fusiform diffusion holes were divided into two groups with cross-sectional widths of W = 1.7D and W = 2.0D, respectively. Three fusiform cross section shapes in each group included only downstream wall outer convex, only upstream wall outer convex, or a combination of both. Simulations were performed in a flat plate model using a 3D steady computational fluid dynamics method under an engine-representative condition. The simulation results showed that the fusiform diffusion hole with only an outer convex upstream wall migrates the coolant laterally toward the hole centerline, and then forms or enhances a tripeak effectiveness pattern. Conversely, the fusiform diffusion hole with an outer convex downstream wall intensely expands the coolant to the hole two sides, and results in a bipeak effectiveness pattern, regardless of the upstream wall shape. Compared with the rectangular diffusion holes, the fusiform diffusion holes with only an upstream wall outer convex significantly increase the overall effectiveness at high blowing ratios. The increased magnitude is approximately 20% for the hole of W = 1.7D at M = 2.5. Besides, the fusiform diffusion holes with an outer convex upstream wall increase the discharge coefficient about 5%, within the moderate to high blowing ratio range.

Investigations on the Influence of Rib Orientation Angle on Film Cooling Performance of Compound Holes

2018 ◽  
Author(s):  
Lin Ye ◽  
Cun-liang Liu ◽  
Hai-yong Liu ◽  
Hui-ren Zhu ◽  
Jian-xia Luo
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Discharge Coefficient ◽  
Orientation Angle ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio

To investigate the effects of the inclined ribs on internal flow structure in film hole and the film cooling performance on outer surface, experimental and numerical studies are conducted on the effects of rib orientation angle on film cooling of compound cylindrical holes. Three coolant channel cases, including two ribbed cross-flow channels (135° and 45° angled ribs) and the plenum case, are studied under three blowing ratios (0.5, 1.0 and 2.0). 2D contours of film cooling effectiveness as well as heat transfer coefficient were measured by transient liquid crystal measurement technique (TLC). The steady RANS simulations with realizable k-ε turbulence model and enhanced wall treatment were performed. The results show that the spanwise width of film coverage is greatly influenced by the rib orientation angle. The spanwise width of the 45° rib case is obviously larger than that of the 135° rib case under lower blowing ratios. When the blowing ratio is 1.0, the area-averaged cooling effectiveness of the 135° rib case and the 45° rib case are higher than that of the plenum case by 38% and 107%, respectively. With the increase of blowing ratio, the film coverage difference between different rib orientation cases becomes smaller. The 45° rib case also produces higher heat transfer coefficient, which is higher than the 135° rib case by 3.4–8.7% within the studied blowing ratio range. Furthermore, the discharge coefficient of the 45° rib case is the lowest among the three cases. The helical motion of coolant flow is observed in the hole of 45° rib case. The jet divides into two parts after being blown out of the hole due to this motion, which induces strong velocity separation and loss. For the 135° rib case, the vortex in the upper half region of the secondary-flow channel rotates in the same direction with the hole inclination direction, which leads to the straight streamlines and thus results in lower loss and higher discharge coefficient.

Effects of Double Wall Cooling Configuration and Conditions on Performance of Full-Coverage Effusion Cooling

2017 ◽  
Vol 139 (5) ◽  
Author(s):  
Nathan Rogers ◽  
Zhong Ren ◽  
Warren Buzzard ◽  
Brian Sweeney ◽  
Nathan Tinker ◽  
...  
Keyword(s):  
Film Cooling ◽  
Cross Flow ◽  
Hole Array ◽  
Adiabatic Wall ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Full Coverage ◽  
Cooling Hole ◽  
Double Wall

Experimental results are presented for a double wall cooling arrangement which simulates a portion of a combustor liner of a gas turbine engine. The results are collected using a new experimental facility designed to test full-coverage film cooling and impingement cooling effectiveness using either cross flow, impingement, or a combination of both to supply the film cooling flow. The present experiment primarily deals with cross flow supplied full-coverage film cooling for a sparse film cooling hole array that has not been previously tested. Data are provided for turbulent film cooling, contraction ratio of 1, blowing ratios ranging from 2.7 to 7.5, coolant Reynolds numbers based on film cooling hole diameter of about 5000–20,000, and mainstream temperature step during transient tests of 14 °C. The film cooling hole array consists of a film cooling hole diameter of 6.4 mm with nondimensional streamwise (X/de) and spanwise (Y/de) film cooling hole spacing of 15 and 4, respectively. The film cooling holes are streamwise inclined at an angle of 25 deg with respect to the test plate surface and have adjacent streamwise rows staggered with respect to each other. Data illustrating the effects of blowing ratio on adiabatic film cooling effectiveness and heat transfer coefficient are presented. For the arrangement and conditions considered, heat transfer coefficients generally increase with streamwise development and increase with increasing blowing ratio. The adiabatic film cooling effectiveness is determined from measurements of adiabatic wall temperature, coolant stagnation temperature, and mainstream recovery temperature. The adiabatic wall temperature and the adiabatic film cooling effectiveness generally decrease and increase, respectively, with streamwise position, and generally decrease and increase, respectively, as blowing ratio becomes larger.

Investigations on the Influence of Rib Orientation Angle on Film Cooling Performance of Cylindrical Holes

2017 ◽  
Author(s):  
Lin Ye ◽  
Cun-liang Liu ◽  
Hui-ren Zhu ◽  
Jian-xia Luo ◽  
Ying-ni Zhai
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Discharge Coefficient ◽  
Cross Flow ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Flow Channels ◽  
Cylindrical Holes

This paper presents an experimental and numerical investigation on the film cooling with different coolant feeding channel structures. Two ribbed cross-flow channels with rib-orientation of 135° and 45° respectively and the plenum coolant channel have been studied and compared to find out the effect of rib orientation on the film cooling performances of cylindrical holes. The film cooling effectiveness and heat transfer coefficient were measured by the transient heat transfer measurement technique with narrow-band thermochromic liquid crystal. Numerical simulations with realizable k-ε turbulence model were also performed to analyze the flow mechanism. The results show that the coolant channel structure has a notable effect on the flow structure of film jet which is the most significant mechanism affecting the film cooling performance. Generally, film cooling cases fed with ribbed cross-flow channels have asymmetric counter-rotating vortex structures and related asymmetric temperature distributions, which make the film cooling effectiveness and the heat transfer coefficient distributions asymmetric to the hole centerline. The discharge coefficient of the 45° rib case is the lowest among the three cases under all the blowing ratios. And the plenum case has higher discharge coefficient than the 135° rib case under low blowing ratio. With the increase of blowing ratio, the discharge coefficient of the 135° rib case gets larger than the plenum case gradually, because the vortex in the upper half region of the coolant channel rotates in the same direction with the film hole inclination direction and makes the jet easy to flow into the film hole in the 135° rib case.

scholarly journals Interaction Mechanism and Loss Analysis of Mixing between Film Cooling Jet and Passage Vortex

Entropy ◽  
2021 ◽  
Vol 24 (1) ◽  
pp. 15
Author(s):  
Ziyu Chen ◽  
Kexin Hu ◽  
Yinbo Mao ◽  
Xinrong Su ◽  
Xin Yuan
Keyword(s):  
Film Cooling ◽  
Interaction Mechanism ◽  
Leading Edge ◽  
Underlying Mechanism ◽  
Entropy Generation Rate ◽  
Cooling Performance ◽  
Loss Analysis ◽  
Blowing Ratio ◽  
Passage Vortex ◽  
Cooling Hole

The interaction between the film-cooling jet and vortex structures in the turbine passage plays an important role in the endwall cooling design. In this study, a simplified topology of a blunt body with a half-cylinder is introduced to simulate the formation of the leading-edge horseshoe vortex, where similarity compared with that in the turbine cascade is satisfied. The shaped cooling hole is located in the passage. With this specially designed model, the interaction mechanism between the cooling jet and the passage vortex can therefore be separated from the crossflow and the pressure gradient, which also affect the cooling jet. The loss-analysis method based on the entropy generation rate is introduced, which locates where losses of the cooling capacity occur and reveals the underlying mechanism during the mixing process. Results show that the cooling performance is sensitive to the hole location. The injection/passage vortex interaction can help enhance the coolant lateral coverage, thus improving the cooling performance when the hole is located at the downwash region. The coolant is able to conserve its structure in that, during the interaction process, the kidney vortex with the positive rotating direction can survive with the negative-rotating passage vortex, and the mixture is suppressed. However, the larger-scale passage vortex eats the negative leg of the kidney vortices when the cooling hole is at the upwash region. As a result, the coolant is fully entrained into the main flow. Changes in the blowing ratio alter the overall cooling effectiveness but have a negligible effect on the interaction mechanism. The optimum blowing ratio increases when the hole is located at the downwash region.

Performance Evaluation of a Novel Film-Cooling Hole

2012 ◽  
Vol 134 (10) ◽  
Author(s):  
Ki-Don Lee ◽  
Kwang-Yong Kim
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Three Dimensional ◽  
Lateral Spreading ◽  
The Novel ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Cooling Hole ◽  
Shaped Hole

This paper presents a numerical investigation of the film-cooling performance of a novel film-cooling hole in comparison with a fan-shaped hole. The novel shaped hole is designed to increase the lateral spreading of coolant on the cooling surface. The film-cooling performance of the novel shaped hole is evaluated at a density ratio of 1.75 and the range of the blowing ratio of 0.5–2.5. The simulations were performed using three-dimensional Reynolds-averaged Navier–Stokes analysis with the SST k-ω model. The numerical results for the fan-shaped hole show very good agreement with the experimental data. For the blowing ratio of 0.5, the novel shaped film-cooling hole shows a similar cooling performance as the fan-shaped hole. However, as the blowing ratio increases, the novel shaped hole shows greatly improved lateral spreading of the coolant and the cooling performance in terms of the film-cooling effectiveness in comparison with the fan-shaped hole.

Effects of Pin-Fin Shapes on Mesh-Fed Slot Film Cooling for a Flat-Plate Model

2019 ◽  
Vol 11 (3) ◽  
Author(s):  
Xiao-Ming Tan ◽  
Jing-Zhou Zhang ◽  
Qing-Zhi Cai
Keyword(s):  
Flat Plate ◽  
Film Cooling ◽  
Coolant Flow ◽  
Plate Model ◽  
Cross Sectional ◽  
Cooling Performance ◽  
Pin Fin ◽  
Pin Fins ◽  
Cooling Hole ◽  
Slot Film Cooling

Experimental and numerical research is performed to illustrate the effects of pin-fin shapes on mesh-fed slot film cooling performance on a flat-plate model. Three types of pin-fin shapes (such as circular, elliptical, and drop-shaped) with the same cross-sectional area are taken into consideration. The results show that a pair of counter rotating vortices is still generated for the mesh-fed slot film cooling scheme due to the strong “jetting” effect of coolant flow at the slot outlet. As the coolant jet ejecting from mesh-fed slot is capable of establishing more uniform film layer over the protected surface, the kidney vortices are illustrated to have weakly detrimental role on the film cooling performance. By the shaping of pin fins, the uniformity of coolant flow exiting mesh-fed slot is improved in comparison to the baseline case of circular shape, especially for the elliptical-shape pin-fin array. Therefore, the jetting effect of coolant flow is alleviated for the elliptical and drop-shaped pin-fin meshes when compared to the circular pin-fin mesh. In general, the pin-fin shape has nearly no influence on cooling effectiveness immediately downstream the film cooling-hole outlet. However, beyond x/s = 5, the elliptical and drop-shaped pin fins are demonstrated to be advantageous over the circular pin fins.

Finite Element Analysis of Thermal-Mechanical Behavior in the Thermal Barrier Coatings With Cooling Hole Structure

2017 ◽  
Author(s):  
Jishen Jiang ◽  
Zhenwei Cai ◽  
Weizhe Wang ◽  
Yingzheng Liu
Keyword(s):  
Mechanical Behavior ◽  
Thermal Barrier Coatings ◽  
Film Cooling ◽  
Operating Conditions ◽  
Thermal Barrier ◽  
Transfer Coefficients ◽  
Adiabatic Wall ◽  
Element Analysis ◽  
Barrier Coatings ◽  
Cooling Hole

The present work aims to investigate the thermal-mechanical behavior in thermal barrier coatings (TBCs) with a round film cooling hole under gas turbine operating conditions. The adiabatic wall temperatures and surface heat transfer coefficients are firstly calculated for thermal boundary conditions. Subsequently, stress analyses during both thermal exposure and cooling down period are presented. The results show that: although the cooling hole has lower temperature, large stress concentration still appears because of the geometry of cooling holes and thermal mismatch between TBCs and substrate. The huge thermal stress may lead to pre-mature failure of TBCs, which should be carefully considered in the design of film cooling-TBC system.

Effects of Double Wall Cooling Configuration and Conditions on Performance of Full Coverage Effusion Cooling

2016 ◽  
Author(s):  
Nathan Rogers ◽  
Zhong Ren ◽  
Warren Buzzard ◽  
Brian Sweeney ◽  
Nathan Tinker ◽  
...  
Keyword(s):  
Film Cooling ◽  
Cross Flow ◽  
Hole Array ◽  
Adiabatic Wall ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Full Coverage ◽  
Cooling Hole ◽  
Double Wall

Experimental results are presented for a double wall cooling arrangement which simulates a portion of a combustor liner of a gas turbine engine. The results are collected using a new experimental facility designed to test full coverage film cooling and impingement cooling effectiveness using either cross flow, impingement, or a combination of both to supply the film cooling flow. The present experiment primarily deals with cross flow supplied full coverage film cooling for a sparse film cooling hole array that has not been previously tested. Data are provided for turbulent film cooling, contraction ratio of 1, blowing ratios ranging from 2.7 to 7.5, coolant Reynolds numbers based on film cooling hole diameter of about 5,000–20,000, and mainstream temperature step during transient tests of 14 °C. The film cooling hole array consists of a film cooling hole diameter of 6.4 mm with non-dimensional streamwise (X/de) and spanwise (Y/de) film cooling hole spacing of 15 and 4, respectively. The film cooling holes are streamwise inclined at an angle of 25 degrees with respect to the test plate surface and have adjacent streamwise rows staggered with respect to each other. Data illustrating the effects of blowing ratio on adiabatic film cooling effectiveness and heat transfer coefficient are presented. For the arrangement and conditions considered, heat transfer coefficients generally increase with streamwise development, and increase with increasing blowing ratio. The adiabatic film cooling effectiveness is determined from measurements of adiabatic wall temperature, coolant stagnation temperature, and mainstream recovery temperature. The adiabatic wall temperature and adiabatic film cooling effectiveness generally decrease and increase, respectively, with streamwise position, and generally decrease and increase, respectively, as blowing ratio becomes larger.

Sign in / Sign up

Export Citation Format

Share Document