Solar Thermal Application for Decentralized Food Baking Using Scheffler Reflector Technology

2018 ◽  
Vol 140 (6) ◽  
Author(s):  
Iqra Ayub ◽  
Anjum Munir ◽  
Abdul Ghafoor ◽  
Waseem Amjad ◽  
Muhammad Salman Nasir
Keyword(s):  
Fluid Dynamic ◽  
Low Cost ◽  
Three Dimensional ◽  
Quality Parameters ◽  
Energy Utilization ◽  
Average Value ◽  
Airflow Distribution ◽  
Series Of Experiments ◽  
Food Processes ◽  
Maximum Retention

Baking is an energy intensive unit operation. The thermal application of solar energy is getting attention in food processes by eliminating the facts of interrupted supply and fluctuated costs of nonrenewable energy sources. This study has been carried out for the design and development of solar bakery unit which comprises of a 10 m2 Scheffler reflector focusing all the beam radiations on a secondary reflector that further concentrate the beam radiations toward the heat receiver of solar bakery unit to heat up the air circulated through baking chamber employing a photovoltaic operated fan. Computational fluid dynamic (CFD)-based three-dimensional (3D) simulation was performed to analyze the design for uniform air distribution in the baking chamber. The system designed configurations gave quite good results for airflow distribution. The receiver temperature reached between 300 and 400 °C while temperature at the inlet of baking chamber was in the range of 200–230 °C, sufficient for most of the products to be baked. The maximum available solar power at receiver was calculated to be 3.46 kW having an average efficiency of 63%. A series of experiments were conducted for the baking of cakes and total energy available in baking chamber was about 3.29 kW and cake utilized 0.201 kW energy to be baked. The average value of energy utilization ratio was found to be 45%. As a base, the study would lead to the development of an appropriate and low cost solar baking units for the maximum retention of quality parameters and energy saving.

scholarly journals Study on the Effect of the Three-Dimensional Electrode in Degradation of Methylene Blue by Lithium Modified Rectorite

2016 ◽  
Vol 2016 ◽  
pp. 1-6 ◽  
Author(s):  
Jian Huang ◽  
Yin’an Ming ◽  
Ying Du ◽  
Yingru Wang ◽  
Ci’en Wang
Keyword(s):  
Methylene Blue ◽  
Electrical Property ◽  
Adsorption Property ◽  
Low Cost ◽  
Three Dimensional ◽  
Cell Voltage ◽  
Operating Conditions ◽  
The Novel ◽  
Synthetic Solution ◽  
Series Of Experiments

This study presents the electrochemical degradation of methylene blue (MB) wastewater in a synthetic solution using three-dimensional particle electrodes. The novel particle electrodes were fabricated in this work using the lithium modified rectorite (Li-REC). The adsorption property of the fabricated particle electrodes was studied in a series of experiments. The optimum electrochemical operating conditions of plate distance, cell voltage, and concentration of electrolyte were 2 cm, 9 V, and 0.06 mol L−1, respectively. It was also found that microwave irradiation can effectively improve the adsorption property and electrical property of the fabricated electrodes. In addition, the scanning electron microscope (SEM) of the fabricated electrodes was investigated. The experimental results revealed the order of adsorption property and electrical property of the fabricated electrodes. So, fabricated electrodes are not only of low cost and mass produced, but also efficient to achieve decolorization of MB solution.

scholarly journals Cooling Characteristics of Film-Cooled Turbine Blades

1984 ◽  
Author(s):  
T. Abe ◽  
N. Doi ◽  
T. Kawaguchi ◽  
T. Yamane ◽  
T. Kumagai ◽  
...  
Keyword(s):  
Film Cooling ◽  
Small Deviation ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Cooling Effectiveness ◽  
Average Value ◽  
Pin Fin ◽  
Series Of Experiments ◽  
Cooling Air Flow ◽  
Cooling Air

A series of experiments was performed to measure the cooling effectiveness of pin-fin type blades applicable to the first-stage blades of the high pressure turbine for the Advanced Gas Turbine of Japan (AGTJ-100A). Actual pin-fin type blades were used in three-dimensional hot cascade tests. Resulting cooling effectiveness distributions in chordwise direction showed relatively small deviation from the high average value and closely corresponded with analytical predictions. Another major finding was that for film cooling blades, particularly with a shower head film cooling, it is essential in the cascade tests to set the ratio between the coolant and mainstream temperature at values the same as real conditions. This makes it possible to simulate cooling air flow distributions in the blades of high temperature actual turbines using low temperature tests. This is also applicable to vanes with a shower head film cooling.

Fabrication of 3D Temperature Sensor Using Magnetostrictive Inkjet Printhead

2020 ◽  
Vol 64 (5) ◽  
pp. 50405-1-50405-5
Author(s):  
Young-Woo Park ◽  
Myounggyu Noh
Keyword(s):  
Flexible Electronics ◽  
Inkjet Printing ◽  
Temperature Sensor ◽  
Computer Aided Design ◽  
Low Cost ◽  
Three Dimensional ◽  
Drop On Demand ◽  
Aided Design ◽  
Nanoparticle Ink ◽  
Inkjet Printhead

Abstract Recently, the three-dimensional (3D) printing technique has attracted much attention for creating objects of arbitrary shape and manufacturing. For the first time, in this work, we present the fabrication of an inkjet printed low-cost 3D temperature sensor on a 3D-shaped thermoplastic substrate suitable for packaging, flexible electronics, and other printed applications. The design, fabrication, and testing of a 3D printed temperature sensor are presented. The sensor pattern is designed using a computer-aided design program and fabricated by drop-on-demand inkjet printing using a magnetostrictive inkjet printhead at room temperature. The sensor pattern is printed using commercially available conductive silver nanoparticle ink. A moving speed of 90 mm/min is chosen to print the sensor pattern. The inkjet printed temperature sensor is demonstrated, and it is characterized by good electrical properties, exhibiting good sensitivity and linearity. The results indicate that 3D inkjet printing technology may have great potential for applications in sensor fabrication.

Constructive Optimisation of the Propeller Type Mixing Devices Using the Virtual and Rapid Prototyping

2017 ◽  
Vol 68 (3) ◽  
pp. 453-458 ◽  
Author(s):  
Daniel Besnea ◽  
Alina Spanu ◽  
Iuliana Marlena Prodea ◽  
Gheorghita Tomescu ◽  
Iolanda Constanta Panait
Keyword(s):  
Rapid Prototyping ◽  
Low Cost ◽  
Scale Up ◽  
Three Dimensional ◽  
Rapid Identification ◽  
Multidisciplinary Optimization ◽  
External Diameter ◽  
Process Industries ◽  
Parametric Cad ◽  
Shaft Torque

The paper points out the advantages of rapid prototyping for improving the performances/constructive optimization of mixing devices used in process industries, here exemplified to propeller types ones. The multidisciplinary optimization of the propeller profile affords its design using parametric CAD methods. Starting from the mathematical curve equations proposed for the blade profile, it was determined its three-dimensional virtual model. The challenge has been focused on the variation of propeller pitch and external diameter. Three dimensional ranges were manufactured using the additive manufacturing process with Marker Boot 3D printer. The mixing performances were tested on the mixing equipment measuring the minimum rotational speed and the correspondent shaft torque for complete suspension achieved for each of the three models. The virtual and rapid prototyping method is newly proposed by the authors to obtain the basic data for scale up of the mixing systems, in the case of flexible production (of low quantities), in which both the nature and concentration of the constituents in the final product varies often. It is an efficient and low cost method for the rapid identification of the optimal mixing device configuration, which contributes to the costs reduction and to the growing of the output.

Sandwich hydrogel with confined plasmonic Cu/carbon cells for efficient solar water purification

2021 ◽  
Author(s):  
Cheng Tian ◽  
Chengcheng Li ◽  
Delun Chen ◽  
Yifan Li ◽  
LEI XING ◽  
...  
Keyword(s):  
Solar Energy ◽  
Water Purification ◽  
Low Cost ◽  
Energy Utilization ◽  
Solar Water ◽  
Solar Energy Utilization

Designing low-cost and efficient evaporation system to maximize solar energy utilization is of great importance for the emerging solar water purification technologies. Herein, we demonstrate a universal sandwich hydrogel by...

scholarly journals An “Animated Spatial Time Machine” in Co-Creation: Reconstructing History Using Gamification Integrated into 3D City Modelling, 4D Web and Transmedia Storytelling

2021 ◽  
Vol 10 (7) ◽  
pp. 460
Author(s):  
Mario Matthys ◽  
Laure De Cock ◽  
John Vermaut ◽  
Nico Van de Weghe ◽  
Philippe De Maeyer
Keyword(s):  
Public Space ◽  
Low Cost ◽  
Three Dimensional ◽  
Physical Situation ◽  
Time Machine ◽  
Transmedia Storytelling ◽  
Spatial Reconstruction ◽  
3D Software ◽  
The City ◽  
City Models

More and more digital 3D city models might evolve into spatiotemporal instruments with time as the 4th dimension. For digitizing the current situation, 3D scanning and photography are suitable tools. The spatial future could be integrated using 3D drawings by public space designers and architects. The digital spatial reconstruction of lost historical environments is more complex, expensive and rarely done. Three-dimensional co-creative digital drawing with citizens’ collaboration could be a solution. In 2016, the City of Ghent (Belgium) launched the “3D city game Ghent” project with time as one of the topics, focusing on the reconstruction of disappeared environments. Ghent inhabitants modelled in open-source 3D software and added animated 3D gamification and Transmedia Storytelling, resulting in a 4D web environment and VR/AR/XR applications. This study analyses this low-cost interdisciplinary 3D co-creative process and offers a framework to enable other cities and municipalities to realise a parallel virtual universe (an animated digital twin bringing the past to life). The result of this co-creation is the start of an “Animated Spatial Time Machine” (AniSTMa), a term that was, to the best of our knowledge, never used before. This research ultimately introduces a conceptual 4D space–time diagram with a relation between the current physical situation and a growing number of 3D animated models over time.

scholarly journals Minimal Monitoring of Improvements in Energy Performance after Envelope Renovation in Subsidized Single Family Housing in Madrid

2020 ◽  
Vol 13 (1) ◽  
pp. 235
Author(s):  
Fernando Martín-Consuegra ◽  
Fernando de Frutos ◽  
Ignacio Oteiza ◽  
Carmen Alonso ◽  
Borja Frutos
Keyword(s):  
Energy Efficiency ◽  
Energy Savings ◽  
Low Cost ◽  
Energy Performance ◽  
Quality Parameters ◽  
Urban Setting ◽  
Single Family ◽  
Nineteen Fifties ◽  
Environment Quality ◽  
Urban Complex

This study quantified the improvement in energy efficiency following passive renovation of the thermal envelope in highly inefficient residential complexes on the outskirts of the city of Madrid. A case study was conducted of a single-family terrace housing, representative of the smallest size subsidized dwellings built in Spain for workers in the nineteen fifties and sixties. Two units of similar characteristics, one in its original state and the other renovated, were analyzed in detail against their urban setting with an experimental method proposed hereunder for simplified, minimal monitoring. The dwellings were compared on the grounds of indoor environment quality parameters recorded over a period covering both winter and summer months. That information was supplemented with an analysis of the energy consumption metered. The result was a low-cost, reasonably accurate measure of the improvements gained in the renovated unit. The monitoring output data were entered in a theoretical energy efficiency model for the entire neighborhood to obtain an estimate of the potential for energy savings if the entire urban complex were renovated.

Optimum Design for the Frame of Open Type Abrasive Flow Polish Machine

2012 ◽  
Vol 497 ◽  
pp. 89-93
Author(s):  
Liang Liang Yuan ◽  
Ke Hua Zhang ◽  
Li Min
Keyword(s):  
Finite Element ◽  
Natural Frequency ◽  
Finite Element Methods ◽  
Optimization Design ◽  
Low Cost ◽  
Three Dimensional ◽  
Force Model ◽  
Optimization Analysis ◽  
Open Type ◽  
Set Up

In order to process heterotype hole of workpiece precisely, an open abrasive flow polish machine is designed, and the optimization design of machine frame is done for low cost. Firstly, basing on the parameters designed with traditional ways, three-dimensional force model is set up with the soft of SolidWorks. Secondly, the statics and modal analysis for machine body have been done in Finite element methods (FEM), and then the optimization analysis of machine frame has been done. At last, the model of rebuild machine frame has been built. Result shows that the deformation angle value of machine frame increased from 0.72′ to 1.001′, the natural frequency of the machine decreased from 75.549 Hz to 62.262 Hz, the weight of machine decreased by 74.178 Kg after optimization. It meets the strength, stiffness and angel stiffness requirement of machine, reduces the weight and cost of machine.

Experimental investigation on the three-dimensional flow field from a meltblowing slot die

e-Polymers ◽  
2020 ◽  
Vol 20 (1) ◽  
pp. 724-732
Author(s):  
Changchun Ji ◽  
Yudong Wang
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Great Influence ◽  
Distribution Characteristics ◽  
Air Velocity ◽  
Three Dimensional Flow ◽  
Dimensional Flow ◽  
Airflow Distribution ◽  
Slot Die ◽  
Center Area

AbstractTo investigate the distribution characteristics of the three-dimensional flow field under the slot die, an online measurement of the airflow velocity was performed using a hot wire anemometer. The experimental results show that the air-slot end faces have a great influence on the airflow distribution in its vicinity. Compared with the air velocity in the center area, the velocity below the slot end face is much lower. The distribution characteristics of the three-dimensional flow field under the slot die would cause the fibers at different positions to bear inconsistent air force. The air velocity of the spinning centerline is higher than that around it, which is more conducive to fiber diameter attenuation. The violent fluctuation of the instantaneous velocity of the airflow could easily cause the meltblowing fiber to whip in the area close to the die.

scholarly journals Coupled Fluid–Solid Numerical Simulation for Flow Field Characteristics and Supporting Performance of Flexible Support Cylindrical Gas Film Seal

Aerospace ◽  
2021 ◽  
Vol 8 (4) ◽  
pp. 97
Author(s):  
Junfeng Sun ◽  
Meihong Liu ◽  
Zhen Xu ◽  
Taohong Liao ◽  
Xiangping Hu ◽  
...  
Keyword(s):  
Flow Field ◽  
Film Thickness ◽  
Fluid Dynamic ◽  
Structural Characteristics ◽  
Structural Parameters ◽  
Equivalent Stress ◽  
Three Dimensional ◽  
High Rotational Speed ◽  
Flexible Support ◽  
Flow Field Characteristics

A new type of cylindrical gas film seal (CGFS) with a flexible support is proposed according to the working characteristics of the fluid dynamic seal in high-rotational-speed fluid machinery, such as aero-engines and centrifuges. Compared with the CGFS without a flexible support, the CGFS with flexible support presents stronger radial floating characteristics since it absorbs vibration and reduces thermal deformation of the rotor system. Combined with the structural characteristics of a film seal, an analytical model of CGFS with a flexible wave foil is established. Based on the fluid-structure coupling analysis method, the three-dimensional flow field of a straight-groove CGFS model is simulated to study the effects of operating and structural parameters on the steady-state characteristics and the effects of gas film thickness, eccentricity, and the number of wave foils on the equivalent stress of the flexible support. Simulation results show that the film stiffness increases significantly when the depth of groove increases. When the gas film thickness increases, the average equivalent stress of the flexible support first decreases and then stabilizes. Furthermore, the number of wave foils affects the average foils thickness. Therefore, when selecting the number of wave foils, the support stiffness and buffer capacity should be considered simultaneously.

Sign in / Sign up

Export Citation Format

Share Document