scholarly journals Embedded Two-Phase Cooling of High Flux Electronics Via Press-Fit and Bonded FEEDS Coolers

2018 ◽  
Vol 140 (3) ◽  
Author(s):  
Raphael K. Mandel ◽  
Daniel G. Bae ◽  
Michael M. Ohadi
Keyword(s):  
Experimental Testing ◽  
High Heat ◽  
Heat Fluxes ◽  
Coefficient Of Performance ◽  
System Level ◽  
Pumping Power ◽  
Test Chip ◽  
Two Phase ◽  
Press Fit ◽  
Two Phase Cooling

The increasing heat densities in electronic components and focus on energy efficiency have motivated utilization of embedded two-phase cooling, which reduces system-level thermal resistance and pumping power. To achieve maximum benefit, high heat fluxes and vapor qualities should be achieved simultaneously. While many researchers have achieved heat fluxes in excess of 1 kW/cm2, vapor qualities are often below 10%, requiring a significantly large amount of energy spent on subcooling or pumping power, which minimizes the benefit of using two-phase thermal transport. In this work, we describe our recent work with cooling devices utilizing film evaporation with an enhanced fluid delivery system (FEEDS). The design, calibration, and experimental testing of a press-fit and bonded FEEDS test section are detailed here. Heat transfer and pressure drop performance was characterized and discussed. With the press-fit Si test chip, heat fluxes in excess of 1 kW/cm2 were obtained at vapor qualities approaching 45% and a coefficient of performance (COP) approaching 1400. With the bonded SiC test chip, heat fluxes in excess of 1 kW/cm2 were achieved at a vapor quality of 85% and heat densities approaching 490 W/cm3.

Model Predictive Control of a Pumped Two-Phase Cooling System With Microchannel Heat Exchangers

2018 ◽  
Author(s):  
Oyuna Angatkina ◽  
Andrew Alleyne
Keyword(s):  
Heat Flux ◽  
Model Predictive Control ◽  
Predictive Control ◽  
Heat Exchangers ◽  
Cooling System ◽  
High Heat ◽  
High Heat Flux ◽  
Two Phase ◽  
Cooling Systems ◽  
Two Phase Cooling

Two-phase cooling systems provide a viable technology for high–heat flux rejection in electronic systems. They provide high cooling capacity and uniform surface temperature. However, a major restriction of their application is the critical heat flux condition (CHF). This work presents model predictive control (MPC) design for CHF avoidance in two-phase pump driven cooling systems. The system under study includes multiple microchannel heat exchangers in series. The MPC controller performance is compared to the performance of a baseline PI controller. Simulation results show that while both controllers are able to maintain the two-phase cooling system below CHF, MPC has significant reduction in power consumption compared to the baseline controller.

Analytical Model Quantifying the Net Coolant Flow Rate to a Microstructured Copper Surface validated with Two-Phase PIV Measurements

2021 ◽  
Author(s):  
Matt Harrison ◽  
Joshua Gess
Keyword(s):  
Heat Transfer ◽  
Analytical Model ◽  
Flow Rate ◽  
Circular Disk ◽  
Nucleate Boiling ◽  
High Heat ◽  
Heat Fluxes ◽  
Coolant Flow ◽  
Coolant Flow Rate ◽  
Two Phase

Abstract Using Particle Image Velocimetry (PIV), the amount of fluid required to sustain nucleate boiling was quantified to a microstructured copper circular disk. Having prepared the disk with preferential nucleation sites, an analytical model of the net coolant flow rate requirements to a single site has been produced and validated against experimental data. The model assumes that there are three primary phenomena contributing to the coolant flow rate requirements at the boiling surface; radial growth of vapor throughout incipience to departure, bubble rise, and natural convection around the periphery. The total mass flowrate is the sum of these contributing portions. The model accurately predicts the quenching fluid flow rate at low and high heat fluxes with 4% and 30% error of the measured value respectively. For the microstructured surface examined in this study, coolant flow rate requirements ranged from 0.1 to 0.16 kg/sec for a range of heat fluxes from 5.5 to 11.0 W/cm2. Under subcooled conditions, the coolant flow rate requirements plummeted to a nearly negligible value due to domination of transient conduction as the primary heat transfer mechanism at the liquid/vapor/surface interface. PIV and the validated analytical model could be used as a test standard where the amount of coolant the surface needs in relation to its heat transfer coefficient or thermal resistance is a benchmark for the efficacy of a standard surface or boiling enhancement coating/surface structure.

High Heat Flux Subcooled Flow Boiling of Methanol in Microtubes

2015 ◽  
Author(s):  
Farzad Houshmand ◽  
Hyoungsoon Lee ◽  
Mehdi Asheghi ◽  
Kenneth E. Goodson
Keyword(s):  
Heat Flux ◽  
Pressure Drop ◽  
Flow Boiling ◽  
High Heat ◽  
Heat Fluxes ◽  
Two Phase ◽  
Subcooled Flow Boiling ◽  
Subcooled Flow ◽  
Inner Diameter ◽  
Phase Pressure

As the proper cooling of the electronic devices leads to significant increase in the performance, two-phase heat transfer to dielectric liquids can be of an interest especially for thermal management solutions for high power density devices with extremely high heat fluxes. In this paper, the pressure drop and critical heat flux (CHF) for subcooled flow boiling of methanol at high heat fluxes exceeding 1 kW/cm2 is investigated. Methanol was propelled into microtubes (ID = 265 and 150 μm) at flow rates up to 40 ml/min (mass fluxes approaching 10000 kg/m2-s), boiled in a portion of the microtube by passing DC current through the walls, and the two-phase pressure drop and CHF were measured for a range of operating parameters. The two-phase pressure drop for subcooled flow boiling was found to be significantly lower than the saturated flow boiling case, which can lead to lower pumping powers and more stability in the cooling systems. CHF was found to be increasing almost linearly with Re and inverse of inner diameter (1/ID), while for a given inner diameter, it decreases with increasing heated length.

Experimental evaluation of a compact two-phase cooling system for high heat flux electronic packages

2019 ◽  
Vol 163 ◽  
pp. 114338 ◽  
Author(s):  
Fengze Hou ◽  
Wenbo Wang ◽  
Hengyun Zhang ◽  
Cheng Chen ◽  
Chuan Chen ◽  
...  
Keyword(s):  
Heat Flux ◽  
Experimental Evaluation ◽  
Cooling System ◽  
High Heat ◽  
High Heat Flux ◽  
Electronic Packages ◽  
Two Phase ◽  
Two Phase Cooling

Spatial and Temporal Wall Temperature Fluctuations in Two-Phase Flow in Microgap Coolers

2010 ◽  
Author(s):  
Jessica Sheehan ◽  
Avram Bar-Cohen
Keyword(s):  
Heat Transfer ◽  
High Heat ◽  
Heat Fluxes ◽  
Operating Conditions ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Heat Transfer Coefficients ◽  
High Heat Transfer ◽  
Volumetric Cooling ◽  
Very High

Heat transfer to an evaporating refrigerant and/or dielectric liquid in a microgap channel can provide very high heat transfer coefficients and volumetric cooling rates. Recent studies at Maryland have established the dominance of the annular flow regime in such microgap channels and related the observed high-quality peak of an M-shaped heat transfer coefficient curve to the onset of local dryout. The present study utilizes infrared thermography to locate such nascent dryout regions and operating conditions. Data obtained with a 210 micron microgap channel, operated with a mass flux of 195.2 kg/m2-s and heat fluxes of 10.3 to 26 W/cm2 are presented and discussed.

Two-Phase Convective Cooling for Ultrahigh Power Dissipation in Microprocessors

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
Peter A. Kottke ◽  
Thomas M. Yun ◽  
Craig E. Green ◽  
Yogendra K. Joshi ◽  
Andrei G. Fedorov
Keyword(s):  
High Heat ◽  
Heat Fluxes ◽  
High Mass ◽  
Two Phase ◽  
Worst Case ◽  
Pressure Drops ◽  
System Pressure ◽  
Performance Trends ◽  
Wide Range ◽  
Contraction And Expansion

We present results of modeling for the design of microgaps for the removal of high heat fluxes via a strategy of high mass flux, high quality, and two-phase forced convection. Modeling includes (1) thermodynamic analysis to obtain performance trends across a wide range of candidate coolants, (2) evaluation of worst-case pressure drop due to contraction and expansion in inlet/outlet manifolds, and (3) 1D reduced-order simulations to obtain realistic estimates of different contributions to the pressure drops. The main result is the identification of a general trend of improved heat transfer performance at higher system pressure.

High Heat Flux Two-Phase Cooling in Silicon Multimicrochannels

2008 ◽  
Vol 31 (3) ◽  
pp. 691-701 ◽  
Author(s):  
B. Agostini ◽  
J.R. Thome ◽  
M. Fabbri ◽  
B. Michel
Keyword(s):  
Heat Flux ◽  
High Heat ◽  
High Heat Flux ◽  
Two Phase ◽  
Two Phase Cooling

A Review of Two-Phase Forced Cooling in Three-Dimensional Stacked Electronics: Technology Integration

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
Craig Green ◽  
Peter Kottke ◽  
Xuefei Han ◽  
Casey Woodrum ◽  
Thomas Sarvey ◽  
...  
Keyword(s):  
Heat Flux ◽  
Heat Sink ◽  
Three Dimensional ◽  
High Heat ◽  
Heat Fluxes ◽  
Thermal Design ◽  
High Heat Flux ◽  
Two Phase ◽  
Forced Cooling ◽  
Fluidic Routing

Three-dimensional (3D) stacked electronics present significant advantages from an electrical design perspective, ranging from shorter interconnect lengths to enabling heterogeneous integration. However, multitier stacking exacerbates an already difficult thermal problem. Localized hotspots within individual tiers can provide an additional challenge when the high heat flux region is buried within the stack. Numerous investigations have been launched in the previous decade seeking to develop cooling solutions that can be integrated within the 3D stack, allowing the cooling to scale with the number of tiers in the system. Two-phase cooling is of particular interest, because the associated reduced flow rates may allow reduction in pumping power, and the saturated temperature condition of the coolant may offer enhanced device temperature uniformity. This paper presents a review of the advances in two-phase forced cooling in the past decade, with a focus on the challenges of integrating the technology in high heat flux 3D systems. A holistic approach is applied, considering not only the thermal performance of standalone cooling strategies but also coolant selection, fluidic routing, packaging, and system reliability. Finally, a cohesive approach to thermal design of an evaporative cooling based heat sink developed by the authors is presented, taking into account all of the integration considerations discussed previously. The thermal design seeks to achieve the dissipation of very large (in excess of 500 W/cm2) background heat fluxes over a large 1 cm × 1 cm chip area, as well as extreme (in excess of 2 kW/cm2) hotspot heat fluxes over small 200 μm × 200 μm areas, employing a hybrid design strategy that combines a micropin–fin heat sink for background cooling as well as localized, ultrathin microgaps for hotspot cooling.

Experimental Characterization of Two-Phase Cooling of Power Electronics in Thermosiphon and Forced Convection Modes

2021 ◽  
Vol 143 (3) ◽  
Author(s):  
Fabio Battaglia ◽  
Farah Singer ◽  
David C. Deisenroth ◽  
Michael M. Ohadi
Keyword(s):  
Heat Flux ◽  
Thermal Resistance ◽  
Power Electronics ◽  
Forced Convection ◽  
Heat Removal ◽  
High Heat ◽  
Heat Fluxes ◽  
High Heat Flux ◽  
Two Phase ◽  
Total Thermal Resistance

Abstract In this paper, we present the results of an experimental study involving low thermal resistance cooling of high heat flux power electronics in a forced convection mode, as well as in a thermosiphon (buoyancy-driven) mode. The force-fed manifold microchannel cooling concept was utilized to substantially improve the cooling performance. In our design, the heat sink was integrated with the simulated heat source, through a single solder layer and substrate, thus reducing the total thermal resistance. The system was characterized and tested experimentally in two different configurations: the passive (buoyancy-driven) loop and the forced convection loop. Parametric studies were conducted to examine the role of different controlling parameters. It was demonstrated that the thermosiphon loop can handle heat fluxes in excess of 200 W/cm2 with a cooling thermal resistance of 0.225 (K cm2)/W for the novel cooling concept and moderate fluctuations in temperature. In the forced convection mode, a more uniform temperature distribution was achieved, while the heat removal performance was also substantially enhanced, with a corresponding heat flux capacity of up to 500 W/cm2 and a thermal resistance of 0.125 (K cm2)/W. A detailed characterization leading to these significant results, a comparison between the performance between the two configurations, and a flow visualization in both configurations are discussed in this paper.

Sign in / Sign up

Export Citation Format

Share Document