Modeling Strategies for Large Eddy Simulation of Lean Burn Spray Flames

2017 ◽  
Vol 140 (5) ◽  
Author(s):  
S. Puggelli ◽  
D. Bertini ◽  
L. Mazzei ◽  
A. Andreini
Keyword(s):  
Large Eddy Simulation ◽  
Ambient Pressure ◽  
Nox Reduction ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Test Case ◽  
Lean Burn ◽  
Eddy Simulation ◽  
Flamelet Generated Manifold ◽  
Large Eddy

Over the last years, aero-engines are progressively evolving toward design concepts that permit improvements in terms of engine safety, fuel economy, and pollutant emissions. With the aim of satisfying the strict NOx reduction targets imposed by ICAO-CAEP, lean burn technology is one of the most promising solutions even if it must face safety concerns and technical issues. Hence, a depth insight on lean burn combustion is required, and computational fluid dynamics can be a useful tool for this purpose. In this work, a comparison in large eddy simulation (LES) framework of two widely employed combustion approaches like the artificially thickened flame (ATF) and the flamelet generated manifold (FGM) is performed using ANSYS fluent v16.2. Two literature test cases with increasing complexity in terms of geometry, flow field, and operating conditions are considered. First, capabilities of FGM are evaluated on a single swirler burner operating at ambient pressure with a standard pressure atomizer for spray injection. Then, a second test case, operated at 4 bar, is simulated. Here, kerosene fuel is burned after an injection through a prefilming airblast atomizer within a corotating double swirler. Obtained comparisons with experimental results show different capabilities of ATF and FGM in modeling the partially premixed behavior of the flame and provide an overview of the main strengths and limitations of the modeling strategies under investigation.

Modelling Strategies for Large-Eddy Simulation of Lean Burn Spray Flames

2017 ◽  
Author(s):  
S. Puggelli ◽  
D. Bertini ◽  
L. Mazzei ◽  
A. Andreini
Keyword(s):  
Large Eddy Simulation ◽  
Ambient Pressure ◽  
Nox Reduction ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Lean Burn ◽  
Eddy Simulation ◽  
Flamelet Generated Manifold ◽  
Large Eddy ◽  
Modelling Strategies

During the last years aero-engines are progressively evolving toward design concepts that permit improvements in terms of engine safety, fuel economy and pollutant emissions. With the aim of satisfying the strict NOx reduction targets imposed by ICAO-CAEP, lean burn technology is one of the most promising solutions even if it must face safety concerns and technical issues. Hence a depth insight on lean burn combustion is required and Computational Fluid Dynamics (CFD) can be a useful tool for this purpose. In this work a comparison in Large-Eddy Simulation (LES) framework of two widely employed combustion approaches like the Artificially Thickened Flame (ATF) and the Flamelet Generated Manifold (FGM) is performed using ANSYS® Fluent v16.2. Two literature test cases with increasing complexity in terms of geometry, flow field and operating conditions are considered. Firstly, capabilities of FGM are evaluated on a single swirler burner operating at ambient pressure with a standard pressure atomizer for spray injection. Then a second test case, operated at 4 bar, is simulated. Here kerosene fuel is burned after an injection through a prefilming airblast atomizer within a co-rotating double swirler. Obtained comparisons with experimental results show the different capabilities of ATF and FGM in modelling the partially-premixed behaviour of the flame and provides an overview of the main strengths and limitations of the modelling strategies under investigation.

Study of Ignition Processes of a Lean Burn Engine using Large-Eddy Simulation

2019 ◽  
Author(s):  
O. Benoit ◽  
P. Luszcz ◽  
Y. Drouvin ◽  
T. Kayashima ◽  
P. Adomeit ◽  
...  
Keyword(s):  
Large Eddy Simulation ◽  
Lean Burn ◽  
Eddy Simulation ◽  
Large Eddy

Large Eddy Simulation of Combustor and Complete Single-Stage High-Pressure Turbine of the FACTOR Test Rig

2019 ◽  
Author(s):  
Martin Thomas ◽  
Jerome Dombard ◽  
Florent Duchaine ◽  
Laurent Gicquel ◽  
Charlie Koupper
Keyword(s):  
High Pressure ◽  
Large Eddy Simulation ◽  
Combustion Chamber ◽  
Measurement Data ◽  
Single Stage ◽  
High Pressure Turbine ◽  
Lean Burn ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Compact Design

Abstract Development goals for next generation aircraft engines are mainly determined by the need to reduce fuel consumption and environmental impact. To reduce NOx emissions lean combustion technologies will be applied in future development projects. The more compact design and the absence of dilution holes in this type of engines shortens residence times in the combustion chamber and reduces mixing which results in higher levels of swirl, turbulence and temperature distortions at the exit of the combustion chamber. For these engines interactions between components are more important, so that the traditional engine design approach of component-wise optimization will have to be adapted. To study new lean burn architectures the European FACTOR project investigates the transport of hot streaks produced by a non-reactive combustor simulator through a single stage high-pressure turbine. In this work high-fidelity Large Eddy Simulation (LES) of combustor and complete high-pressure turbine are discussed and validated against experimental data. Measurement data is available on P40 (exit of the combustion chamber), P41 (exit of the stator) and P42 (exit of the rotor) and generally shows a good agreement to LES data.

scholarly journals Study of the Wall Thermal Condition Effect in a Lean-Premixed Downscaled Can Combustor Using Large-Eddy Simulation

2016 ◽  
Author(s):  
D. Mira ◽  
M. Vázquez ◽  
G. Houzeaux ◽  
S. Gövert ◽  
J. W. B. Kok ◽  
...  
Keyword(s):  
Turbulent Combustion ◽  
Mixture Fraction ◽  
Flame Stabilization ◽  
Operating Conditions ◽  
Laminar Flames ◽  
Combustion Model ◽  
Test Case ◽  
Eddy Simulation ◽  
Condition Effect ◽  
Large Eddy

The primary purpose of this study is to evaluate the ability of LES, with a turbulent combustion model based on steady flamelets, to predict the flame stabilization mechanisms in an industrial can combustor at full load conditions. The test case corresponds to the downscaled Siemens can combustor tested in the high pressure rig at the DLR. The effects of the wall temperature on the prediction capabilities of the codes is investigated by imposing several heat transfer conditions at the pilot and chamber walls. The codes used for this work are Alya and OpenFOAM, which are well established CFD codes in the fluid mechanics community. Prior to the simulation, results for 1-D laminar flames at the operating conditions of the combustor are compared with the detailed solutions. Subsequently, results from both codes at the mid-plane are compared against the experimental data available. Acceptable results are obtained for the axial velocity, while discrepancies are more evident for the mixture fraction and the temperature, particularly with Alya. However, both codes showed that the heat losses influence the size and length of the pilot and main flame.

On the Combination of Large Eddy Simulation and Phenomenological Soot Modelling to Calculate the Smoke Index From Aero-Engines Over a Large Range of Operating Conditions

2017 ◽  
Author(s):  
Jean Lamouroux ◽  
Stéphane Richard ◽  
Quentin Malé ◽  
Gabriel Staffelbach ◽  
Antoine Dauptain ◽  
...  
Keyword(s):  
Large Eddy Simulation ◽  
Gas Turbines ◽  
Soot Formation ◽  
Operating Conditions ◽  
Extended Model ◽  
Eddy Simulation ◽  
Design Office ◽  
Wide Range ◽  
Large Eddy ◽  
Aero Engines

Nowadays, models predicting soot emissions are, neither able to describe correctly fine effects of technological changes on sooting trends nor sufficiently validated at relevant operating conditions to match design office quantification needs. Yet, phenomenological descriptions of soot formation, containing key ingredients for soot modeling exist in the literature, such as the well-known Leung et al. model (Combust Flame 1991). This approach indeed includes contributions of nucleation, surface growth, coagulation, oxidation and thermophoretic transport of soot. When blindly applied to aeronautical combustors for different operating conditions, this model fails to hierarchize operating points compared to experimental measurements. The objective of this work is to propose an extension of the Leung model, including an identification of its constants over a wide range of condition relevant of gas turbines operation. Today, the identification process can hardly be based on laboratory flames since few detailed experimental data are available for heavy-fuels at high pressure. Thus, it is decided to directly target smoke number values measured at the engine exhaust for a variety of combustors and operating conditions from idling to take-off. A Large Eddy Simulation approach is retained for its intrinsic ability to reproduce finely unsteady behavior, mixing and intermittency. In this framework, The Leung model for soot is coupled to the TFLES model for combustion. It is shown that pressure-sensitive laws for the modelling constant of the soot surface chemistry are sufficient to reproduce engine emissions. Grid convergence is carried out to verify the robustness of the proposed approach. Several cases are then computed blindly to assess the prediction capabilities of the extended model. This study paves the way for the systematic use of a high fidelity tool solution in design office constraints for combustion chamber development.

Numerical and Experimental Investigation on an Effusion-Cooled Lean Burn Aeronautical Combustor: Aerothermal Field and Emissions

2018 ◽  
Vol 141 (4) ◽  
Author(s):  
L. Mazzei ◽  
S. Puggelli ◽  
D. Bertini ◽  
A. Andreini ◽  
B. Facchini ◽  
...  
Keyword(s):  
Temperature Distribution ◽  
Combustion Process ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Flame Spray ◽  
Distribution Factor ◽  
Lean Burn ◽  
Radial Temperature ◽  
Flamelet Generated Manifold ◽  
The Impact

Lean burn combustion is increasing its popularity in the aeronautical framework due to its potential in reducing drastically pollutant emissions (NOx and soot in particular). Its implementation, however, involves significant issues related to the increased amount of air dedicated to the combustion process, demanding the redesign of injection and cooling systems. Also, the conditions at the combustor exit are a concern, as high turbulence, residual swirl, and the impossibility to adjust the temperature profile with dilution holes determine a harsher environment for nozzle guide vanes. This work describes the final stages of the design of an aeronautical effusion-cooled lean burn combustor. Full annular tests were carried out to measure temperature profiles and emissions (CO and NOx) at the combustor exit. Different operating conditions of the ICAO cycle were tested, considering Idle, Cruise, Approach, and Take-off. Scale-adaptive simulations with the flamelet generated manifold (FGM) combustion model were performed to extend the validation of the employed computational fluid dynamics (CFD) methodology and to reproduce the experimental data in terms of radial temperature distribution factor (RTDF)/overall temperature distribution factor (OTDF) profiles as well as emission indexes (EIs). The satisfactory agreement paved the way to an exploitation of the methodology to provide a deeper understanding of the flow physics within the combustion chamber, highlighting the impact of the different operating conditions on flame, spray evolution, and pollutant formation.

Sign in / Sign up

Export Citation Format

Share Document