Tribological Characterization of AZ91 and AE42 Magnesium Alloys in Fretting Contact

2017 ◽  
Vol 140 (1) ◽  
Author(s):  
D. Khabale ◽  
M. F. Wani
Keyword(s):  
Magnesium Alloys ◽  
Coefficient Of Friction ◽  
Normal Load ◽  
Fretting Wear ◽  
Wear Volume ◽  
Dry Sliding ◽  
Running Time ◽  
Average Coefficient ◽  
Tribological Characterization

Fretting wear studies were conducted on AZ91 and AE42 magnesium alloys against steel ball. Average coefficient of friction (COF) remains steady with the increase in running time. However, average coefficient of friction decreases with the increase in normal load and frequency and marginally increases with the increase in amplitude. A constant average coefficient of friction of 0.06 was observed for both AZ91 and AE42 under dry sliding conditions at normal load of 50 N. Wear volume increases linearly with increasing running time. Wear volume first decreases sharply, attains minima, and then increases marginally with the increase in normal load. However, wear volume increases with increasing amplitude and frequency. Higher specific wear rate of 10.5 × 10−6 mm3 N−1·m−1 was observed for AE42, as compared to 4.5 × 10−6 mm3 N−1·m−1 for AZ91. The wear in magnesium alloy was caused by a combination of adhesion, abrasion, oxidation, delamination, and plastic deformation under different fretting conditions.

scholarly journals Tribological Characterization of Polyether Ether Ketone (PEEK) Polymers Produced by Additive Manufacturing for Hydrodynamic Bearing Application

Lubricants ◽  
2021 ◽  
Vol 9 (11) ◽  
pp. 112
Author(s):  
Davide Massocchi ◽  
Giacomo Riboni ◽  
Nora Lecis ◽  
Steven Chatterton ◽  
Paolo Pennacchi
Keyword(s):  
Additive Manufacturing ◽  
Optical Microscope ◽  
Wear Volume ◽  
Coating Materials ◽  
Hydrodynamic Bearing ◽  
Polyether Ether Ketone ◽  
Strength Tests ◽  
Ether Ketone ◽  
Tribological Characterization

The coating materials commonly used in hydrodynamic bearings are the so-called “Babbitt metals” or “white metals”, as defined by ASTM B23-00. Their low Young’s modulus and yield point have encouraged researchers to find new coatings to overcome these limitations. In this paper, the friction and wear of PEEK are studied in a dry sliding environment (without lubrication) using a ball-on-disk tribometer and compared to those of Babbitt metal. Furthermore, the bond strength tests between PEEK and metals/alloys are evaluated. PEEK polymer samples were obtained from cylindrical rods, manufactured by an innovative process for polymer bonding on bearing surfaces, using additive manufacturing technology. The morphologies of the degraded surfaces were examined using a high-resolution metallurgical optical microscope (OM) and a scanning electron microscope (SEM). The coefficients of friction (CoF) were obtained under the alternating ball-on-disk dry tribometer. The results of the experimental activity show that PEEK polymers have CoFs of about 0.22 and 0.16 under the 1 and 5 N applied load, respectively. The CoF and wear volume loss results are reported and compared to the reference Babbitt coating.

scholarly journals Fretting wear rate of sulphur deficient MoSx coatings based on dissipated energy

2001 ◽  
Vol 16 (12) ◽  
pp. 3567-3574 ◽  
Author(s):  
Xiaoling Zhang ◽  
W. Lauwerens ◽  
L. Stals ◽  
Jiawen He ◽  
J-P. Celis
Keyword(s):  
Relative Humidity ◽  
Wear Rate ◽  
Coefficient Of Friction ◽  
Contact Stress ◽  
Ambient Air ◽  
Fretting Wear ◽  
Dissipated Energy ◽  
Wear Volume ◽  
The Coefficient Of Friction ◽  
Crystallographic Orientations

The fretting wear of sulphur-deficient MoSx coatings with different crystallographic orientations has been investigated in ambient air of controlled relative humidity. The coefficient of friction and the wear rate of MoSx coatings sliding against corundum depend not only on fretting parameters like contact stress, fretting frequency, and relative humidity, but also strongly on the crystallographic orientation of the coatings. For randomly oriented MoSx coatings, the coefficient of friction and the wear rate increased significantly with increasing relative humidity. In contrast, basal-oriented MoSx coatings were less sensitive to relative humidity. The coefficient of friction of both types of MoSx coatings decreased on sliding against corundum with increasing contact stress and decreasing fretting frequency. A correlation between dissipated energy and wear volume is proposed. This approach allows detection in a simple way of differences in fretting wear resistance between random- and basal-oriented MoSx coatings tested in ambient air of different relative humidity.

Tribological Characterization of N 80A and 21-4N Valve Materials Against GGG-40 Seat Material Under Dry Sliding Conditions at Temperatures Up To 500 °C

2017 ◽  
Vol 139 (6) ◽  
Author(s):  
Sheikh Shahid Saleem ◽  
M. F. Wani
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Raman Spectroscopy ◽  
Friction Coefficient ◽  
Friction And Wear ◽  
Dry Sliding ◽  
Nimonic 80A ◽  
Tribological Characterization ◽  
Scanning Electron

Friction and wear studies of Nimonic 80A and 21-4N valve materials against GGG-40 under dry sliding conditions, at temperatures ranging from 50 °C to 500 °C, are presented in this paper. Friction coefficient was found to be continuously decreased with time for all tests with prominent running-in behavior seen in the 50 °C and 500 °C tests. Higher friction coefficient and wear were observed at 300 °C as compared to those at 50 °C and 500 °C. Formation of oxide Fe3O4, at 300 °C, was confirmed by Raman spectroscopy, which resulted in a higher friction coefficient and wear. Raman spectroscopy further revealed the presence of α-Fe2O3, hematite, in most cases, with the presence of oxides of Ni–Cr and Ni–Fe as well. Energy dispersive spectroscopy (EDS) results on the samples confirmed the same. Wear at 500 °C was found to be the least for both the valve materials with scanning electron microscopy (SEM) confirming the formation of well-developed glaze layers.

Effect of Fine TiC Particle Reinforcement on the Dry Sliding Wear Behavior of In Situ Synthesized ZA27 Alloy

2018 ◽  
Vol 141 (2) ◽  
Author(s):  
Roshita David ◽  
Rupa Dasgupta ◽  
B. K. Prasad
Keyword(s):  
Wear Rate ◽  
Coefficient Of Friction ◽  
Sliding Wear ◽  
Wear Behavior ◽  
Base Alloy ◽  
Dry Sliding Wear ◽  
Wear Volume ◽  
Dry Sliding ◽  
Material Loss

The in situ method of making zinc-aluminum composites wherein TiC has been introduced has been investigated in the present paper for its microstructural, physical, and dry sliding wear behavior and compared with the base alloy. In the present study, ZA-27 alloy reinforced with 5 and 10 vol % TiC was taken into consideration. The results indicate that the wear rate and coefficient of friction of composites were lower than that of base alloy. The material loss in terms of both wear volume loss and wear rate increases with increase in load and sliding distance, respectively, while coefficient of friction follows a reverse trend with increase in load. Better performance was obtained for 5% TiC reinforcement than with 10% probably due to agglomeration of particles resulting in nonuniform dispersion. Worn surfaces were analyzed by scanning electron microscopy (SEM) analysis.

Finite element analysis of fretting wear considering variable coefficient of friction

2018 ◽  
Vol 233 (5) ◽  
pp. 758-768 ◽  
Author(s):  
Ling Li ◽  
Le Kang ◽  
Shiyun Ma ◽  
Zhiqiang Li ◽  
Xiaoguang Ruan ◽  
...  
Keyword(s):  
Finite Element ◽  
Coefficient Of Friction ◽  
Variable Coefficient ◽  
Friction Model ◽  
Slip Condition ◽  
Fretting Wear ◽  
Partial Slip ◽  
Wear Volume ◽  
The Coefficient Of Friction ◽  
Contact Surfaces

Fretting wear is a kind of material damage in contact surfaces caused by microrelative displacement between two bodies. It can change the profile of contact surfaces, resulting in loosening of fasteners or fatigue cracks. Finite element method is an effective method to simulate the evolution of fretting wear process. In most studies of fretting wear, the coefficient of friction was assumed to be constant to simplify model and reduce the difficulty of solving. However, fretting wear test showed that the coefficient of friction was a variable related to the number of fretting cycles. Therefore, this paper introduces the coefficient of friction as a function of the number of fretting cycles in numerical simulation. A wear model considering variable coefficient of friction is established by combining energy consumption model and adaptive grid technique. The nodes of contact surfaces are updated through the UMESHMOTION subroutine. The effects of constant coefficient of friction and variable coefficient of friction on fretting wear are analyzed by comparing the wear amount under different loading conditions. The results show that when compared with coefficient of friction model, fretting wear is obviously affected by variable coefficient of friction and the variable coefficient of friction model has a larger wear volume when the fretting is in partial slip condition and mixed slip condition. In gross slip condition, the difference of wear volume between variable coefficient of friction model and coefficient of friction model decreases with the increase in the displacement amplitudes.

Modelling the tribological response in dry sliding of boron modified as-cast Ti6Al4V on hardened steel

2021 ◽  
pp. 135065012110592
Author(s):  
Palash Roy Choudhury ◽  
Korimilli Eswar Prasad ◽  
John K. Schueller ◽  
Abhijit Bhattacharyya
Keyword(s):  
Wear Rate ◽  
Coefficient Of Friction ◽  
Boron Content ◽  
Normal Load ◽  
Operating Conditions ◽  
Dry Sliding ◽  
Contour Plots ◽  
The Coefficient Of Friction ◽  
En 31 ◽  
Full Factorial

Tribological characteristics of boron modified as-cast Ti6Al4V alloys are not very well known, but these alloys enjoy improved as-cast mechanical properties and favourable manufacturing economy. Experimental results are reported here for the effects of sliding speed and normal load on the wear rate and the coefficient of friction in dry sliding of these alloys on hardened EN 31 steel. Alloys having 0%, 0.30%, and 0.55% boron by weight were tested. A full factorial experiment assessed the effects of boron content, speed, and load on wear and friction. Interactions between speed and load were found to be statistically significant in influencing the wear rate and the coefficient of friction. Regression models are developed to predict the wear rate and coefficient of friction responses. The developed contour plots can assist designers in choosing operating conditions when selecting these alloys even if the wear mechanisms are unknown. Evidence shows that the wear resistance of Ti6Al4V can be improved by boron addition, and wear regimes are sensitive to boron content.

INVESTIGATION ON DRY SLIDING WEAR BEHAVIOR OF TITANIUM DIOXIDE-REINFORCED MAGNESIUM MATRIX COMPOSITE

2021 ◽  
pp. 2150106
Author(s):  
P. C. ELUMALAI ◽  
R. GANESH
Keyword(s):  
Titanium Dioxide ◽  
Wear Rate ◽  
Coefficient Of Friction ◽  
Wear Mechanisms ◽  
Sliding Wear ◽  
Normal Load ◽  
Dry Sliding Wear ◽  
Dry Sliding ◽  
Sliding Velocity ◽  
Significant Change

In this work, the dry sliding wear behaviors of pure monolithic magnesium and magnesium–titanium dioxide (Mg–TiO2) composites were studied using pin-on-disc tribometer against an oil-hardened nonshrinking die steel (OHNS) counter-disc with a normal load of 0.5–2[Formula: see text]kg and a sliding velocity of 1.5–2.5[Formula: see text][Formula: see text] with the sliding distance and wear track diameter of 1500[Formula: see text]m and 90[Formula: see text]mm, respectively. The pin samples were characterized for their microstructural, nanomechanical and tribological properties such as wear rate, coefficient of friction and wear fractographs. Scanning electron microscopy (SEM) was used to analyze the worn-out surfaces of each pin sample in order to identify the different types of wear and wear mechanisms and the chemical constituents of each element were quantified by energy-dispersive spectroscopy. The influence of TiO2 reinforcements on the nanomechanical behavior was studied by nanoindentation technique. As compared with pure Mg, the nanoindentation strengths of Mg–1.5TiO2, Mg–2.5TiO2 and Mg–5TiO2 composites were found to increase by 11.9%, 22.2% and 35.8%, respectively, which was due to the addition of TiO2 particles and also due to the good bonding at the interface of TiO2 and magnesium particles. From the wear test results, a significant change in wear rate was observed with the change in normal load than that of sliding speed, whereas a significant change in coefficient of friction was noticed with the changes in both normal load and sliding velocity. The dominant wear mechanisms involved under the testing conditions were identified through plotting the contour maps and SEM fractographs. Also, from the fractographs it was noticed that delamination and plowing effect have been the significant wear mechanisms observed during low wear rate of samples, whereas melting, delamination and oxidation wear have been observed during high wear rate of pure Mg and its composites.

Plowing Friction Under Harmonic Normal Loads

1999 ◽  
Vol 121 (2) ◽  
pp. 282-285 ◽  
Author(s):  
D. P. Hess
Keyword(s):  
Shear Strength ◽  
Coefficient Of Friction ◽  
Metal Surfaces ◽  
Sliding Friction ◽  
Normal Load ◽  
Hard Materials ◽  
Lubricated Contacts ◽  
Highly Nonlinear ◽  
Average Coefficient ◽  
The Coefficient Of Friction

The influence of harmonic normal loads on sliding friction is investigated through analysis of contacts consisting of conical and spherical sliders of hard materials on softer metal surfaces. Friction for such contacts is assumed to result from a plowing component and a shearing component. Calculations and experiments show that the coefficient of friction is essentially independent of normal load for contacts with conical sliders. However, for spherical sliders the relation between the coefficient of friction and normal load is highly nonlinear. In the presence of harmonic variations in normal load, this non-linearity causes a shift in the average coefficient of friction. For ideal lubricated contacts, the shearing component of friction is very small and for this case, it is shown that the maximum average reduction in the coefficient of friction is ten percent. When the shearing component is more significant, as with dry contacts, the shift is less. For example, when the shear strength is one-sixth the hardness of the softer material, the maximum average reduction in the coefficient of friction is five percent.

Tribological Characterization of Porous TiO2 Coatings Produced by Electrodeposition

2011 ◽  
Vol 493-494 ◽  
pp. 430-435
Author(s):  
E. Santos ◽  
S.S. Camargo ◽  
G.A. Soares ◽  
Neide K. Kuromoto
Keyword(s):  
Electrolyte Solutions ◽  
Wear Volume ◽  
Oxide Coatings ◽  
Porous Ti ◽  
The Coefficient Of Friction ◽  
Dry Conditions ◽  
Anodic Oxidation Method ◽  
Tribological Characterization ◽  
Scratch Tests

In this work, the resistance to scratch and wear (pin-on-flat) tests of five different porous TiO2 films were compared. Such tribological tests were carried out under dry conditions. The coatings were electrodeposited on commercially pure-Ti by anodic oxidation method in different electrolyte solutions at constant voltages. The scratch tests were conducted by applying increasing normal loads up to 400 mN. The coefficient of friction (COF) varied from 0.2 up to 0.5, and increased at larger penetrations depths. When the electrolyte concentration was changed from 0.5 into 1.0M H2SO4, the COF slightly decreased. Scanning electron microscopy indicated that the coatings produced in H2SO4/150V and Na2SO4/100V did not have their substrates revealed. In addition, the samples anodized in H2SO4/150V had the highest elastic recoveries. Therefore, such coatings seem to be more resistant to scratch tests than the others. The wear tests were carried out with Berkovich tip as counter-face under constant normal loads of 10 mN in 10 forward-backward cycles. The coatings deposited in H2SO4/150V had the lowest wear volume rates. The findings suggest that the porous Ti oxide coatings electrodeposited above their rupture voltages are more suitable to both scratch- and wear-resistance compared to those prepared at the lowest voltage (H2SO4/100V).

Sign in / Sign up

Export Citation Format

Share Document