Unsteady Flow Field and Coarse Droplet Measurements in the Last Stage of a Low-Pressure Steam Turbine With Supersonic Airfoils Near the Blade Tip

2017 ◽  
Vol 139 (9) ◽  
Author(s):  
Ilias Bosdas ◽  
Michel Mansour ◽  
Anestis I. Kalfas ◽  
Reza S. Abhari ◽  
Shigeki Senoo
Keyword(s):  
Flow Field ◽  
Steam Turbine ◽  
Leading Edge ◽  
Low Pressure ◽  
Fast Response ◽  
Operating Conditions ◽  
Electricity Production ◽  
Test Facility ◽  
Steam Turbines ◽  
Last Stage

The largest share of electricity production worldwide belongs to steam turbines. However, the increase of renewable energy production has led steam turbines to operate under part load conditions and increase in size. As a consequence, long rotor blades will generate a relative supersonic flow field at the inlet of the last rotor. This paper presents a unique experiment work that focuses at the top 30% of stator exit in the last stage of an low pressure (LP) steam turbine test facility with coarse droplets and high wetness mass fraction under different operating conditions. The measurements were performed with two novel fast response probes: a fast response probe for three-dimensional flow field wet steam measurements and an optical backscatter probe for coarse water droplet measurements ranging from 30 μm up to 110 μm in diameter. This study has shown that the attached bow shock at the rotor leading edge is the main source of interblade row interactions between the stator and rotor of the last stage. In addition, the measurements showed that coarse droplets are present in the entire stator pitch with larger droplets located at the vicinity of the stator's suction side. Unsteady droplet measurements showed that the coarse water droplets are modulated with the downstream rotor blade-passing period. This set of time-resolved data will be used for in-house computational fluid dynamics (CFD) code development and validation.

Unsteady Flow Field and Coarse Droplet Measurements in the Last Stage of a Low Pressure Steam Turbine With Supersonic Airfoils Near the Blade Tip

2016 ◽  
Author(s):  
Ilias Bosdas ◽  
Michel Mansour ◽  
Anestis I. Kalfas ◽  
Reza S. Abhari ◽  
Shigeki Senoo
Keyword(s):  
Flow Field ◽  
Steam Turbine ◽  
Leading Edge ◽  
Suction Side ◽  
Fast Response ◽  
Operating Conditions ◽  
Electricity Production ◽  
Test Facility ◽  
Steam Turbines ◽  
Last Stage

The largest share of electricity production worldwide belongs to steam turbines. However, the increase of renewable energy production has led steam turbines to operate under part load conditions and increase in size. As a consequence long rotor blades will generate a relative supersonic flow field at the inlet of the last rotor. This paper presents a unique experiment work that focuses at the top 30% of stator exit in the last stage of an LP steam turbine test facility with coarse droplets and high wetness mass fraction under different operating conditions. The measurements were performed with two novel fast response probes. A fast response probe for three dimensional flow field wet steam measurements and an optical backscatter probe for coarse water droplet measurements ranging from 30 up to 110μm in diameter. This study has shown that the attached bow shock at the rotor leading edge is the main source of inter blade row interactions between the stator and rotor of the last stage. In addition, the measurements showed that coarse droplets are present in the entire stator pitch with larger droplets located at the vicinity of the stator’s suction side. Unsteady droplet measurements showed that the coarse water droplets are modulated with the downstream rotor blade-passing period. This set of time-resolved data will be used for in-house CFD code development and validation.

Unsteady Wet Steam Flow Field Measurements in the Last Stage of Low Pressure Steam Turbine

2015 ◽  
Author(s):  
Ilias Bosdas ◽  
Michel Mansour ◽  
Anestis I. Kalfas ◽  
Reza S. Abhari ◽  
Shigeki Senoo
Keyword(s):  
Flow Field ◽  
Steam Turbine ◽  
Total Pressure ◽  
Low Pressure ◽  
Operating Conditions ◽  
Test Facility ◽  
Flow Structures ◽  
Wet Steam ◽  
Operating Condition ◽  
Last Stage

Modern steam turbines need to operate efficiently and safely over a wide range of operating conditions. This paper presents a unique unprecedented set of time-resolved steam flowfield measurements from the exit of the last two stages of a low pressure (LP) steam turbine under various volumetric massflow conditions. The measurements were performed in the steam turbine test facility in Hitachi city in Japan. A newly developed fast response probe equipped with a heated tip to operate in wet steam flows was used. The probe tip is heated through an active control system using a miniature high-power cartridge heater developed in-house. Three different operating points, including two reduced massflow conditions, are compared and a detailed analysis of the unsteady flow structures under various blade loads and wetness mass fractions is presented. The measurements show that at the exit of the second to last stage the flow field is highly three dimensional. The measurements also show that the secondary flow structures at the tip region (shroud leakage and tip passage vortices) are the predominant sources of unsteadiness at 85% span. The high massflow operating condition exhibits the highest level of periodical total pressure fluctuation compared to the reduced massflow conditions at the inlet of the last stage. In contrast at the exit of the last stage, the reduced massflow operating condition exhibits the largest aerodynamic losses near the tip. This is due to the onset of the ventilation process at the exit of the LP steam turbine. This phenomenon results in 3 times larger levels of relative total pressure unsteadiness at 93% span, compared to the high massflow condition. This implies that at low volumetric flow conditions the blades will be subjected to higher dynamic load fluctuations at the tip region.

Design, Manufacturing and Testing of a New Family of Steam Turbine Low Pressure Stages

2007 ◽  
Author(s):  
Lorenzo Cosi ◽  
Jonathon Slepski ◽  
Steven DeLessio ◽  
Michele Taviani ◽  
Amir Mujezinovic´
Keyword(s):  
Power Generation ◽  
Steam Turbine ◽  
Low Pressure ◽  
Full Scale ◽  
Operating Conditions ◽  
Test Facility ◽  
Steam Turbines ◽  
Wide Range ◽  
The Family ◽  
Last Stage

New low pressure (LP), stages for variable speed, mechanical drive and geared power generation steam turbines have been developed. The new blade and nozzle designs can be applied to a wide range of turbine rotational speeds and last stage blade annulus areas, thus forming a family of low pressure stages—High Speed (HS) blades and nozzles. Different family members are exact scales of each other and the tip speeds of the corresponding blades within the family are identical. Thus the aeromechanical and aerodynamic characteristics of the individual stages within the family are identical as well. Last stage blades and nozzles have been developed concurrently with the three upstream stages, creating optimised, reusable low pressure turbine sections. These blades represent a step forward in improving speed, mass flow capability, reliability and aerodynamic efficiency of the low pressure stages for the industrial steam turbines. These four stages are designed as a system using the most modern design tools applied on Power Generation and Aircraft Engines turbo-machineries. The aerodynamic performance of the last three stage of the newly designed group will be verified in a full-scale test facility. The last stage blade construction incorporates a three hooks, axial entry dovetail with improved load carrying capability over other blade attachment methods. The next to the last stage blade also uses a three hooks axial entry dovetail, while the two front stage blades employ internal tangential entry dovetails. The last and next to the last stage blades utilize continuous tip coupling via implementation of integral snubber cover while a Z-lock integral cover is employed for the two upstream stages. Low dynamic strains at all operating conditions (off and on resonance speeds) will be validated via steam turbine testing at realistic steam conditions (steam flows, temperatures and pressures). Low load, high condenser pressure operation will also be verified using a three stage test turbine operated in the actual steam conditions as well. In addition, resonance speed margins of the four stages have been verified through full-scale wheel box tests in the vacuum spin cell, thus allowing the application of these stages to Power Generation applications. Stator blades are produced with a manufacturing technology, which combines full milling and electro-discharge machining. This process allows machining of the blades from an integral disc, and thus improving uniformity of the throat distribution. Accuracy of the throat distribution is also improved when compared to the assembled or welded stator blade technology. This paper will discuss the aerodynamic and aeromechanical design, development and testing program completed for this new low pressure stages family.

Unsteady Wet Steam Flow Field Measurements in the Last Stage of Low Pressure Steam Turbine

2015 ◽  
Vol 138 (3) ◽  
Author(s):  
Ilias Bosdas ◽  
Michel Mansour ◽  
Anestis I. Kalfas ◽  
Reza S. Abhari ◽  
Shigeki Senoo
Keyword(s):  
Flow Field ◽  
Steam Turbine ◽  
Total Pressure ◽  
Low Pressure ◽  
Operating Conditions ◽  
Test Facility ◽  
Flow Structures ◽  
Wet Steam ◽  
Operating Condition ◽  
Last Stage

Modern steam turbines need to operate efficiently and safely over a wide range of operating conditions. This paper presents a unique unprecedented set of time-resolved steam flowfield measurements from the exit of the last two stages of a low pressure (LP) steam turbine under various volumetric massflow conditions. The measurements were performed in the steam turbine test facility in Hitachi city in Japan. A newly developed fast response probe equipped with a heated tip to operate in wet steam flows was used. The probe tip is heated through an active control system using a miniature high-power cartridge heater developed in-house. Three different operating points (OPs), including two reduced massflow conditions, are compared and a detailed analysis of the unsteady flow structures under various blade loads and wetness mass fractions is presented. The measurements show that at the exit of the second to last stage the flow field is highly three dimensional. The measurements also show that the secondary flow structures at the tip region (shroud leakage and tip passage vortices) are the predominant sources of unsteadiness at 85% span. The high massflow operating condition exhibits the highest level of periodical total pressure fluctuation compared to the reduced massflow conditions at the inlet of the last stage. In contrast at the exit of the last stage, the reduced massflow operating condition exhibits the largest aerodynamic losses near the tip. This is due to the onset of the ventilation process at the exit of the LP steam turbine. This phenomenon results in three times larger levels of relative total pressure unsteadiness at 93% span, compared to the high massflow condition. This implies that at low volumetric flow conditions the blades will be subjected to higher dynamic load fluctuations at the tip region.

Influence of a Cylindrical Exhaust Hood Installation on the Last Stage Rotor Blades of a Low Pressure Model Steam Turbine

2017 ◽  
Author(s):  
Fabian F. Müller ◽  
Markus Schatz ◽  
Damian M. Vogt ◽  
Jens Aschenbruck
Keyword(s):  
Flow Field ◽  
Steam Turbine ◽  
Operating Conditions ◽  
Rotor Blades ◽  
Pressure Measurements ◽  
Exhaust Hood ◽  
Blade Vibration ◽  
Time Resolved ◽  
Vibration Behavior ◽  
Last Stage

The influence of a cylindrical strut shortly downstream of the bladerow on the vibration behavior of the last stage rotor blades of a single stage LP model steam turbine was investigated in the present study. Steam turbine retrofits often result in an increase of turbine size, aiming for more power and higher efficiency. As the existing LP steam turbine exhaust hoods are generally not modified, the last stage rotor blades frequently move closer to installations within the exhaust hood. To capture the influence of such an installation on the flow field characteristics, extensive flow field measurements using pneumatic probes were conducted at the turbine outlet plane. In addition, time-resolved pressure measurements along the casing contour of the diffuser and on the surface of the cylinder were made, aiming for the identification of pressure fluctuations induced by the flow around the installation. Blade vibration behavior was measured at three different operating conditions by means of a tip timing system. Despite the considerable changes in the flow field and its frequency content, no significant impact on blade vibration amplitudes were observed for the investigated case and considered operating conditions. Nevertheless, time-resolved pressure measurements suggest that notable pressure oscillations induced by the vortex shedding can reach the upstream bladerow.

Sequential vs Multidisciplinary Coupled Optimization and Efficient Surrogate Modelling of a Last Stage and the Successive Axial Radial Diffuser in a Low Pressure Steam Turbine

2014 ◽  
Author(s):  
Kevin Cremanns ◽  
Dirk Roos ◽  
Arne Graßmann
Keyword(s):  
Steam Turbine ◽  
Design Process ◽  
Energy Demand ◽  
Three Dimensional ◽  
Flow Simulation ◽  
Low Pressure ◽  
Steam Turbines ◽  
Low Pressure Turbine ◽  
Pressure Steam ◽  
Last Stage

In order to meet the requirements of rising energy demand, one goal in the design process of modern steam turbines is to achieve high efficiencies. A major gain in efficiency is expected from the optimization of the last stage and the subsequent diffuser of a low pressure turbine (LP). The aim of such optimization is to minimize the losses due to separations or inefficient blade or diffuser design. In the usual design process, as is state of the art in the industry, the last stage of the LP and the diffuser is designed and optimized sequentially. The potential physical coupling effects are not considered. Therefore the aim of this paper is to perform both a sequential and coupled optimization of a low pressure steam turbine followed by an axial radial diffuser and subsequently to compare results. In addition to the flow simulation, mechanical and modal analysis is also carried out in order to satisfy the constraints regarding the natural frequencies and stresses. This permits the use of a meta-model, which allows very time efficient three dimensional (3D) calculations to account for all flow field effects.

Development of 60Hz Titanium 48-Inch Last Stage Blade for Steam Turbine

2011 ◽  
Author(s):  
Yoriharu Murata ◽  
Naoki Shibukawa ◽  
Itaru Murakami ◽  
Joji Kaneko ◽  
Kenichi Okuno
Keyword(s):  
Steam Turbine ◽  
Mechanical Design ◽  
Thermal Power ◽  
Combined Cycle ◽  
Operating Conditions ◽  
Scale Model ◽  
Test Facility ◽  
Recent Analysis ◽  
Last Stage ◽  
Actual Size

The titanium 48-inch last stage blade that has world’s largest class exhaust annulus area and tip speed for 60Hz steam turbines has been developed. Concept of this blade is to achieve high performance and compact design of steam turbine for 1000MW thermal power plant and 300MW combined cycle plant. In the design of this blade, the optimization design has been done by using the recent analysis technologies, three dimensional CFD in aerodynamic design and FEA in mechanical design. The blade has curved axial fir-tree dovetail, snubber cover both at the tip and at the mid-span. To achieve superior vibration characteristics, continuously coupled structure was adopted for blade connection. To confirm the validity of design, first, sub-scale model blades were provided and tested in model steam turbine test facilities. Second, one row of actual size blades were assembled on the wheel of test rotor and were exposed rotating vibration test in a wheel box. Finally, these blades were tested at actual steam conditions in a full scale steam turbine test facility. In this paper, aerodynamic and mechanical design features will be introduced, and the test results of both sub-scale and actual size blades under real steam turbine operating conditions will be presented.

The Effect of Rotor Casing on Low-Pressure Steam Turbine and Diffuser Interactions

2016 ◽  
Vol 139 (2) ◽  
Author(s):  
Gursharanjit Singh ◽  
Andrew P. S. Wheeler ◽  
Gurnam Singh
Keyword(s):  
Steam Turbine ◽  
Computational Study ◽  
Low Pressure ◽  
Computational Method ◽  
Test Facility ◽  
Leakage Flows ◽  
Flow Features ◽  
Last Stage ◽  
Lp Turbine ◽  
Tip Leakage Flows

The present study aims to investigate the interaction between a last-stage steam turbine blade row and diffuser. This work is carried out using computational fluid dynamics (CFD) simulations of a generic last-stage low-pressure (LP) turbine and axial–radial exhaust diffuser attached to it. In order to determine the validity of the computational method, the CFD predictions are first compared with data obtained from an experimental test facility. A computational study is then performed for different design configurations of the diffuser and rotor casing shapes. The study focuses on typical flow features such as effects of rotor tip leakage flows and subsequent changes in the rotor–diffuser interactions. The results suggest that the rotor casing shape influences the rotor work extraction capability and yields significant improvements in the diffuser static pressure recovery.

Experimental and Numerical Investigation of the Flow in a Low-Pressure Industrial Steam Turbine With Part-Span Connectors

2016 ◽  
Vol 138 (7) ◽  
Author(s):  
Markus Häfele ◽  
Christoph Traxinger ◽  
Marius Grübel ◽  
Markus Schatz ◽  
Damian M. Vogt ◽  
...  
Keyword(s):  
Flow Field ◽  
Steam Turbine ◽  
Numerical Study ◽  
Three Dimensional ◽  
Low Pressure ◽  
Operating Conditions ◽  
Engineering Practice ◽  
Cfd Model ◽  
Wide Range ◽  
The Impact

An experimental and numerical study on the flow in a three-stage low-pressure (LP) industrial steam turbine is presented and analyzed. The investigated LP section features conical friction bolts in the last and a lacing wire in the penultimate rotor blade row. These part-span connectors (PSC) allow safe turbine operation over an extremely wide range and even in blade resonance condition. However, additional losses are generated which affect the performance of the turbine. In order to capture the impact of PSCs on the flow field, extensive measurements with pneumatic multihole probes in an industrial steam turbine test rig have been carried out. State-of-the-art three-dimensional computational fluid dynamics (CFD) applying a nonequilibrium steam (NES) model is used to examine the aerothermodynamic effects of PSCs on the wet steam flow. The vortex system in coupled LP steam turbine rotor blading is discussed in this paper. In order to validate the CFD model, a detailed comparison between measurement data and steady-state CFD results is performed for several operating conditions. The investigation shows that the applied one-passage CFD model is able to capture the three-dimensional flow field in LP steam turbine blading with PSC and the total pressure reduction due to the PSC with a generally good agreement to measured values and is therefore sufficient for engineering practice.

Forced Response Prediction for Steam Turbine Last Stage Blade Subject to Low Engine Order Excitation

2011 ◽  
Author(s):  
Bin Zhou ◽  
Amir Mujezinovic ◽  
Andrew Coleman ◽  
Wei Ning ◽  
Asif Ansari
Keyword(s):  
Steam Turbine ◽  
Low Pressure ◽  
Forced Response ◽  
Operating Conditions ◽  
Low Flow ◽  
Analytical Prediction ◽  
Unsteady Pressure ◽  
Engine Order ◽  
Last Stage ◽  
Cfd Analyses

Low Engine Order (LEO) excitations on a steam turbine Last Stage low-pressure (LP) Bucket (or Blade) (LSB) are largely the result of flow unsteadiness (e.g. flow circulation and reversal) due to low steam exit velocity (Vax) off the LSB at the off-design conditions. These excitations at low frequencies impose major constraints on LP bucket aeromechanical design. In this study, bucket forced response under typical LEO excitation was analytically predicted and correlated to experimental measurements. First, transient CFD analyses were performed at typical low flow, low Vax operating conditions that had been previously tested in a subscale low pressure turbine test rig. The unsteady pressure distribution on the bucket was derived from the transient CFD analyses at frequencies corresponding to the bucket’s modes of vibration. Subsequently, these computed unsteady pressure were mapped onto a LSB finite element model, and forced response analyses were performed to estimate the bucket dynamic response, i.e. the alternating stresses and strains. The analytically predicted bucket response was compared against measured data from airfoil mounted strain gages and good correlation was found between the analytical prediction and the test data. Despite uncertainty associated with various parameters such as damping and unsteady steam forcing etc., the developed methodology provides a viable approach for predicting bucket forced response and in turn High Cycle Fatigue (HCF) capability during early phases of steam turbine LSB design.

Sign in / Sign up

Export Citation Format

Share Document